2019/09 BIOPTICRR20 User Manual BIOPTICRR20 Us e r M a n u a l Instruction description The following are displayed in ASCII string, Baud rate 115200, 8, N, 1 red for the command, green for the reply 1. ISO14443A and ISO15693 General settings 0108000304FF0000 Entry command mode, need to be released after booting Command mode 010A0003041001210000 Parameter setup Register write request. 010C00030410002101000000 Parameter setup Register write request. 0109000304F0000000 Parameter setup AGC Toggle 0109000304F1FF0000 Parameter setup AM PM Toggle 2. ISO14443A Read / Write TAG memory 0109000304A0000000 ISO14443A protocol, 14443A REQA. 14443A REQA.
[042E41E3425F1D8080,7F]
010E00030418A207AAAABBBB0000 write data AAAAAAAA to 01 memory block Request mode.
[]
010A0003041830070000 write data BBBBBBBB to 02 memory block
[AAAABBBB88880000000000000000000067C8]
Copyright 2019, BiOptic Inc. 2 BIOPTICRR20 Us e r M a n u a l 3. ISO15693 Read / Write TAG memory 010B000304140401000000 ISO15693 protocol, ISO 15693 Inventory request
[FFC7BA76500104E0,7F]
010F00030418002101AAAAAAAA0000 write data AAAAAAAA to 01 memory block Request mode.
[00]
010F00030418002102BBBBBBBB0000 write data BBBBBBBB to 02 memory block Request mode.
[00]
010B000304180020010000 Read 01 memory block Request mode.
[00AAAAAAAA]
010B000304180020020000 Read 02 memory block Request mode.
[00BBBBBBBB]
Copyright 2019, BiOptic Inc. 3 BIOPTICRR20 Us e r M a n u a l Copyright 2019, BiOptic Inc. 4 BIOPTICRR20 Us e r M a n u a l FCC 15.19 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.105 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 15.21 Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible Modular Approval OEM INTEGRATION INSTRUCTIONS:
This device is intended only for OEM integrators under the following conditions: 1) The module must be installed in the host equipment such that 20 cm is maintained between the antenna and users, and 2) the transmitter module may not be co-located with any other transmitter or antenna. As long as 2) conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization for this module in combination with the host equipment is no longer considered valid and the FCC ID of the module cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. USERS MANUAL OF THE END PRODUCT:
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID: 2AUQB-STMB003-B ". The following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. info@bioptic.com.tw https://www.bioptic.com.tw Copyright 2019, BiOptic Inc. 5