1 Assembly Prep To prepare for the assembly of your BirdBike, first take out all pieces of the BirdBike from the box and remove all packaging. Also, open the accessory box and remove all tools, parts and everything else thats inside of it. 2.5 mm Allen key Pedals
(x 2) 3mm / 4mm /
5mm Y-wrench L-key Phillips Screwdriver 13mm / 15mm Two-sided Wrench Cap nut and washer Wheel Reflectors
(x 2) and fasteners (x 2) Rear and Front Reflectors Battery Keys Power Supply This Manual and Cable A F R A M E Saddle Rear fender Rear rim Tire Tail light Rear disc brake Motor Kickstand Front Sprocket Crank Pedal Frame Handlebar Front light Front fender Front rim Fork Front disc brake Battery 1 4 2 Install the handlebar Remove Display from the Handlebar Use the 2.5mm Allen Key to remove the screw thats behind the display on the handlebar. If the display isnt easily removed from the handlebar, use the hex key to gently push it from the back of the handlebar through the hole from where the screw was removed. 2.5 mm Allen key Y-wrench Install the Handlebar Use the 5mm end of the Y-wrench to remove the hex bolt from inside the steerer tube and insert the handlebar over the steerer tube. After the handlebar is installed and lined up properly with the tire and frame, insert the hex bolt through the handlebar and into the steerer tube. Use the 5mm end of the Y-wrench to gently tighten the hex bolt into the handlebar so that theres no play between the fork and frame. Finally, make sure the handlebar, frame, and front wheel are still aligned and tighten the two steering stem screws with the 5mm end of the Y-wrench so the handlebar stays in place. V F R A M E V F R A M E 1 6 3 Attach the front fender Y-wrench 4 heel Install the front wheel Cap Nut and Cap Nut and Washer Washer Wrench Wrench Attach the front fender to the fork by using the screws that are already in the fork legs. otector from the front wheel axle Be sure to remove the plastic front rotor protector from the front wheel axle Use the 4mm end of the Y-wrench to remove the two screws from the fork legs and then tighten the screws through the holes at the end of the fender mounts. Using the 4mm end of the Y-wrench remove the screw thats on the top of the backside of the fork and tighten the screw through the fender mount bracket on top of the fender so that its secured tightly to the back of the fork. When tightening the fender, avoid rubbing the Y-wrench on the frame so the paint doesnt get scratched. Also, dont over tighten the screws to avoid stripping the holes. before starting this step. Align the front wheel axle so that its inside of the fork slots on both sides. The side of the fork slots on both sides. The side with the brake rotor should be aligned so that it fits inside the front disc brake. hat it fits inside the front disc brake. Once the fork slots are sitting on both sides of the axle, install washers at both s of the axle, install washers at both ends and tighten up the cap nuts on the outside using the 15mm end of the utside using the 15mm end of the wrench. After installing the front wheel, extend the kickstand for better stability and easier assembly during the next steps. V F R A M E 1 8 5 Attach the pedals Wrench Pedals 6 Install the display 2.5 mm Allen key For the final step before powering on your BirdBike, reinstall the display back into the handlebar so that the Bird logo is at the bottom. Be sure to not pinch the cable inside of the handlebar while reinstalling. Once reinstalled, use the 2.5mm Allen key to replace and tighten the screw under the display so that its tightened into place inside of the handlebar. Connect the one end of the power cable coming from the bottom of the display to the other end of the power cable that is coming out of the bottom of the frame. At this point you can power on your BirdBike, but be sure to read through the rest of this manual before riding. Install the left and right pedals by screwing them into the crank. Pay attention to which pedal is being installed on the left and the right as the left pedal is reverse threaded so it is tightened counter-clockwise. You can tell the two pedals apart by looking for the R on the right pedal and L on the left. After the pedals are screwed on by hand, use the 15mm end of the wrench to give the pedals a final tightening. R L 2 0 F U N C T I O N S O V E R V I E W Operating Options Speed display Power button Walk mode
+ button
- button Head light Battery capacity display Switch between mph and km/h Assist level Mileage display Error warning P O W E R O N O F F WA L K M O D E After long pressing the power button, the BirdBike will be turned on. While the After pressing and holding the - button for 2 seconds the BirdBike will go into Walk power is on, press and hold the power Mode. The display will show the push button again to turn off the power. symbol and you will receive The power will automatically shut off after 5 minutes if not being used. D I S P L AY I N T E R FA C E After the BirdBike is turned on, the display defaults to showing real-time speed and total distance traveled (miles or km). With a short press of the power button you can toggle through the total distance
(miles/km) and single trip distance
(miles/km). power-assistance while pushing the BirdBike in more difficult situations, like going uphill. When you release the button, Walk Mode will automatically turn off. The power-assisted Walk Mode function should only be used while pushing the electric vehicle and never used while riding. 2 2 T U R N O N O F F T H E H E A D L I G H T S B AT T E R Y L E V E L S E T T I N G S M O D E M P H & K M H P 1 Press and hold the
+ key for 2 seconds When the battery is full, the five-segment to turn on the headlight. When the battery icon will be fully lit and the number headlight is on, the display brightness will of bars will decrease as the battery level also automatically dim. Whenever natural decreases. When the battery is low and To enter Settings Mode first power on the BirdBike, then long press and hold keys +/- at the same time. Once in Settings Mode you adjust from mph to km/h, set a When P1 is displayed in the speed position while in Settings Mode, press the
+/- buttons to switch the display between mph or km/h. After selecting, short press lighting is insufficient (such as in bad needs charging, the battery icon will flash. speed limit, set wheel diameter, and adjust the power button to save. weather) or when riding in the dark, you should always turn on the headlight. Press and hold the + key again for 2 seconds to switch off the headlight. A S S I S T L E V E L Short press the
+ / - buttons to switch the assist level of the BirdBike and change the output power of the motor. Level 0 is no assistance, and level 5 offers the highest amount of assist. The default level when the BirdBike is first turned on is level 5, and each subsequent time it will default to the last assist level that was used. E R R O R C O D E D I S P L AY Error code display: For more information on error codes, please visit support.bird.co. When an error code is displayed, please troubleshoot or contact BirdBike support as soon as possible as the BirdBike will not be able to be ridden normally until the error is resolved. the brightness of the display. While In Settings Mode, you can toggle up and down with the up (+) and down (-) buttons. Short press the power button to adjust the tem you want to change, then short press the power button after making your selection to save. To exit Settings Mode just long press the
- button for 2 seconds. Also, while in Settings Mode if no operation is performed for 30 seconds, then the display will return back to normal. S P E E D L I M I T P 2 When P2 is displayed in the speed position while in Settings Mode and the speed limit value is displayed in the trip position, you can then adjust the speed limit with the
+/- buttons. The minimum is 7 mph
(12km/h) and the maximum is 20mph
(32km/h). After selecting, short press the power button to save. 2 4 W H E E L D I A M E T E R P 3 D I S P L AY B R I G H T N E S S P 4 A U TO M AT I C P O W E R O F F T I M E R P 5 S E R V I C E R E M I N D E R :
When P4 is displayed in the speed position When P5 is displayed at the speed position After the BirdBike has been ridden 300 miles When P3 is displayed in the speed position while in Settings Mode, the wheel diameter setting will be shown in inches and can be adjusted with the +/- buttons. Be sure to know the proper sizes as selecting the wrong size can result in unexpected speeds. After selecting, press the power button so save. while in Settings Mode, the display brightness settings from 1 to 5 are displayed according to the current setting. 1 is the lowest brightness setting, and 5 is the highest (default setting is 5). D A R K B R I G H T 1 2 3 4 5 After the setting is completed, short press the power button to save. while in Settings Mode, choose 0-9 by using the +/- buttons, which represents the automatic shutdown time in
(500km), there will be a service inspection reminder shown on the display the next time its turned on. If the reminder isnt minutes. The default setting to power off marked as complete, then it will be displayed automatically after 5 minutes and setting the timer to 0 means that auto power off will be disabled. After selecting, short press the power button to save. R E S E T T R I P M E T E R P 6 When P6 is displayed at the speed position while in Settings Mode, press the +/-
buttons to select either Y or N. After selecting Y, short press the power button to reset the trip meter to 0. After resetting the trip meter, short press the power button to save the parameters. every time the vehicle is turned on. The reminder can be cleared by a short press of the power button. To remove the service reminder completely until the next 300 miles (500km), the rider must connect to the BirdBike through the Bird App and mark the service inspection as complete. Once marked complete in the Bird App, the service reminder will then no longer be displayed by default each time the BirdBike is powered on. 2 62 6 Operation and Safety Instructions R E A D B E F O R E R I D I N G Do not drive under the influence of alcohol. For your personal safety, you must pay attention to the following The charger should be used and maintained correctly in safe use of the BirdBike:
accordance with the method required by this manual. It is recommended to always wear a helmet when riding. Carefully read the warning labels and instructions of the Do not exceed the maximum load of 265 lbs (120.2 kg) and no more than one rider at a time. purchased from Bird only. When riding in rain or snow, it will take longer to slow the vehicle, so be aware of braking earlier than normal. Try to avoid riding in severe weather, such as heavy rain, snow, or wind. charger before use. When replacing the charger, it should be the brakes. Please do not replace any parts by yourself to avoid damage. Before washing the ebike, you should read and understand the part of the manual about the "Precautions for washing". Do not touch things on the road with your feet while riding. If any parts are damaged while riding that affect safety, While riding at high speed, be sure to brake the bike slowly, please stop riding immediately. and do not brake suddenly under any circumstances. You should not listen to music while riding (because when When adjusting the handlebars or saddles, care should be When driving at night, slow down, drive with caution and use taken not to expose the safety marks of the handlebars and the lights of the vehicle. Anyone who suffers from diseases such as hypertension, hernia, concussion, epilepsy, and cardiovascular disease should not ride the BirdBike. Do not follow motor vehicles too closely (because they may slow down or turn at any time), and always pay attention to BirdBike. type of riding you plan to do. It is best to wear a pair of sports sunglasses, which can reduce the damage of ultraviolet rays to the eyes and protect the eyes from tree branches and flying rocks or stones. Please perform regular maintenance and inspection of your saddles. normally. For your personal safety, you must pay attention to the following safe use of electric bicycles:
Always check your BirdBike before riding. If there are any issues found, please seek professional assistance with solving the issue or repair. Do not park the BirdBike in building halls, evacuation stairs, or Always check whether the front and rear brakes work walkways. Do not charge or park the BirdBike in residential buildings. Always check that handlebars, front and rear wheels, and all Keep away from combustibles when charging, and do not other parts of the BirdBike are tightened properly. leave charging for an extended period of time. The battery should be used and maintained correctly in Precautions while riding:
accordance with the method required by this manual. The battery should not be disassembled without authorization and should be recycled by professional experts. Pay attention and observe all pedestrians, vehicles, obstacles, and others using the road at all times. Try to ride in designated bicycle lanes or the edge of the road, in the direction of traffic flow. It is recommended to ride on city roads. Stop at stop signs, slow down and watch traffic at intersections. Jackets, boots, trousers, gloves, etc. are effective protective clothing to prevent abrasions if an accident were to occur while riding. It is recommended to wear them to protect yourself. Do not wear loose clothing to avoid the risk of entanglementin the moving parts of the BirdBike. Please wear appropriate safety equipment according to the you listen, it distracts your attention, and you cannot hear the sound of horns or other sounds of motor vehicles, which is very dangerous) If you have any problems while riding, please resolve the problem if possible or contact Bird support for help. Precautions for washing the BirdBike:
When washing the BirdBike, do not directly pour water on the motor and the front and rear axles to prevent water from affecting the performance and life of the product. When washing the BirdBike, do not use a strong steam or high-pressure water spray. After washing the vehicle or riding through water, pay special attention to the working conditions of the brakes.The braking capability may be reduced in these circumstances. 2 8 Maintenance and general troubleshooting Inspection of handlebar and front & rear wheel:
Inspection of front and rear brakes Move the BirdBike up, down, front, back, left and right to check Adjustment of the brake lever: Pinch the front and rear brake whether the handlebars and the axle nuts of the front and rear levers, and conrm whether the brakes are working when the wheels are tightened properly, whether the handlebars are distance between the brake lever and the handlebar is inch. tightened properly, and whether there is any abnormal rubbing or damage happening between parts Adjustment method of the front and rear brakes: The distance between the brake and the brake lever is specied to be Push the vehicle back and forth to check whether the front between 10-20mm. and rear wheels rotate smoothly and without any abnormal noise or rubbing. Carefully check the entire vehicle before riding and if you nd any issues, please contact a professional for repair or contact Bird support for help. When the brake is in a tightly gripped state, the brake pad and the brake disc should be contacting evenly. The brake pads and brake discs should be replaced at the same time (the adjustment of the rear wheel brake is the same as that of the front wheel brake). Inspection of power circuit and lighting circuit Battery installation status Turn on the power, operate the lighting switch, check whether the headlights and taillights are on, and if they are at normal Conrm that the battery is in a xed state, connected, and operating properly. levels. Check for any damage with the lighting system. Check whether the power cables on the BirdBike are connected and are operating safely as intended as well as whether all connectors are functioning properly. The rotation parts of the wheels and pedals are maintained and checked regularly, and lubricating oil is added to the position of the rotation axis. Ensure that the corresponding parts can rotate normally without resistance. 3 0 Belt tightness adjustment and requirements Use a belt tension meter to measure the recommended range of tension values (35-45LBS) according to the method below Loosen the 4 m6x16mm screws at the rear hook to adjust the position and lock four screws. Conrm that the indicator arm is fully Place the Krikit gauge on top of the belt, and lowered. As shown in the picture, put your then place the gauge in the middle of the full index nger in the rubber nger ring or length of the belt, making sure that the edge above the hand pressure spring plate. of the gauge is close to the belt. Press the spring plate of the tester until it The measurement point is the intersection of clicks. Be sure to use only one nger. line A and line B. The displayed tension gauge reading is: 20 KG (40 LBS) Rotate the crank 1/4 turn, then repeat the previous steps 1 to step 4. Repeat the rotation and measure 3 times or more. BirdBike Limited Manufacturers Warranty FCC Statement The BirdBike comes with a limited manufacturers warranty and is covered from any defects or issues that are outside of normal wear & tear within the warranty period and terms outlined at support.bird.co. Do not modify the BirdBike as it will void your warranty and introduce potential safety issues. Read and understand all safety warnings listed on the product label and in this manual. Proof of purchase must be veried before any warranty claim is led. info. Warranty terms only apply to the original owner. If you need any type of support or warranty information for your BirdBike, please contact us before returning it back to wherever you purchased it. The BirdBike Support Team is ready to help you via phone or email and you can also visit support.bird.co for more Phone: 1-888-309-3702 (M-F 9a-5p EST) Email: BirdBike@bird.co Web: support.bird.co This device complies with Part 15 of the FCC rules. Operation is
-Consult the dealer or an experienced radio/TV technician for subject to the following two conditions: 1) this device may not help. cause harmful interference, and 2) this device must accept any interference received, including interference that may cause Changes or modications not expressly approved by the party undesired operation. responsible for compliance could void your authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC The distance between user and products should be no less rules. These limits are designed to provide reasonable than 20cm protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures:
-Reorient the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into and outlet on a circuit different from that to which the receiver is connected. 3 2 ISED Statement This device contains licenceexempt transmitter(s)/receiv-
er(s) that comply with Innovation, Science and Economic Development Canadas licenceexempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. ADVERTENCIA IC Cet appareil contient des metteurs /
rcepteurs exempts de licence conformes aux RSS
(RSS)d'Innovation, Sciences et Dveloppement conomique Canada. Le fonctionnement est soumis auxdeux conditions suivantes : (1) Cet appareil ne doit pas causer d'interfrences.
(2) Cet appareil doit accepter toutes les interfrences, y compris celles susceptibles deprovoquer un fonctionnement indsirable de l'appareil. This device complies with ISED RF radiation exposure limits set forth for an uncontrolled environment. Prop 65 Warning This product can expose you to chemicals including chromium, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to: http://www.p65warnings.ca.gov. 3 4 Questions? Weve got answers. Visit support.bird.co for more info. Phone: 1-888-309-3702 (M-F 9a-5p EST) Email: BirdBike@bird.co