FCC ID: SPYBTS002 Bluetooth Scanner

Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:

The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.

II User Quick Guide Bluetooth Scanner Please read this manual thoroughly and carefully before you start to use this device and keep this document in the safe place to get easily after reading it. This Guide is to introduce the user the basic ways to use We have tried to avoid as few mistake as possible in the manual. However, if there is any trouble or loss caused by this manual, we are sorry that we are not able to take such kind of responsibility. This document is preliminary version and will be subject to change without any notice in advance. Followings are the notices you have to mind on the safe use:

This device has taken the safety into consideration if user wrongly uses this device under very dangerous case. To avoid any kind of accident, please follow the following principals:

Danger!

Please do not put the device into water resulting in short-circuit and fire. It cannot be used or stocked under the conditions of overheat or high temperature which will cause the battery become hot, fired& broken etc issues to cause failure and safety concern. Please do not put it in the place which is easily to get fire. Warning!

Please stop using immediately when there is some weird smell or overheat under the charging or operation mode. When it is still under charging mode after lasting for a long time (more than that standard required time), Please stop charging immediately. Please do not use the adaptor outside and do not use the cotton cloth to pack it which will easily to get electric shock or fire. Please start to charge this device in the place without any water-spray or moisture. If there is any dust on the plug of AC adapter, please use the dry cloth to clean to avoid any fire accident. Please do not use the wet hand to pull out the AC adapter which will cause electric shock. If there is any cable seriously twisted or broken, Please stop using immediately or it will easily to cause electric shock, short-circuit or fire. Please do not use this adapter on the other different devices. NOTICES:

Please dont put it close to fire or directly under the sunlight, which will cause deformed and defective easily. Please do not drop this device under the strong strike and impact. Please stop using immediately when there is some dew on the device. Please make sure the adaptor is properly plugged into the socket or it will easily to cause electric shock, short-circuit or fire. When you are trying to pull out the plug, please do not pull the cable only but must pull from the connector head. Except charging the power, please pull out the adapter plug from the socket or it will cause the fire accident. Please do not put any heavy thing on this device, which might cause some cutting accident. The notices must to be minded when using:

Regarding the battery life, defect, repair or other issues, please confirm they are not caused by errors of the user operation. It is possible there will be some information to be wiretapped or leak during the wireless transmission, which case will not be under our charge. Please do not use any alcohol, benzine or cleaner liquid with grinding function on this device. Please do not hurt the surface of Scan window which will cause it not workable on scanning. Bluetooth This device is design based on Bluetooth standard specification but it maybe not workable with the other kind of BT device. Special Features Easy to use and convenient to carry due to its small and light design. CYCLOPS II is with COS Image scanner which can read the 1D and 2D barcode. Compared with the other laser scanners, CYCLOPS II is small, reliable and can resist any kind of high impact from the environment. CYCLOPS II is Better than the normal barcode scanner, and it can read any reverse barcode. You can use the attached AC adaptor or through the USB connection to PC to charge the battery power. With Bluetooth connection, CYCLOPS II can transmit the scanned data to PC, notebook or other mobile devices. If you use iPhone or iPad (iOS) device, you can use the software keyboard to display and save the max 8,000 data files (data size:2048Byte) with its massive storage function. When you are using CYCLOPS II usb port connecting to the PC, it will become the mobile storage device and help you to get the data easily. Built-in Time auto-correction function can save the read date& time together with Data. You can also save the configuration file into PC which can be duplicated into multiple CYCLOPS II to simplify the set-up process. Bluetooth LED Scan Led Charge Led Buzzer volume can set up as totally OFF/ High/ Mid/ Low 4 levels. Items inside the package Please confirm if there is any below item of the package listed in lack or broken:

If such issue happens, Please immediately contact the store where you bought. Data collector Strap AC Adaptor Quick guide USB cableOption to buy Key features on the device:

Scanner window LED Light Status:

Reset buttom USB port Function Key Scan Key AC port Strap holes Scan LED Battery LED Bluetooth LED Scan (Power) key Function key AC Port USB Reset button Strap hole Result of Scanning Barcode Green light onSuccessful Red light onFailed Blinking OrangeSystem firmware is updating OrangeSystem firmware update is completed Battery Status Green light onCharging completed Green light twinklingPower too Low Red light onPower Charging Red light twinklingFailed on Charging Result of Bluetooth connection:

Green light twinkling fastWaiting for Paring connection Green light twinkling slowly: Data is Pairing successfully and transmitting data Press the key button for 3 seconds to turn on and start Barcode scanning According to which mode to activate different functions This is for power charging This USB port for data transmission Press this button to reset all values into Default values You can put the strap through this hole Mode There are three different modes for your different applications to choose:

Real Mode (You can choose HID or SPP profile ) You can use BT to transfer the data right after scanning and it will also show the error message when data transmission is failed. Batch mode You can save the data into memory after scanning and use the below two ways to get: (1) Use BT SPP program to get data.

(2) Connecting with PC to get data. Before using this device, please remember not to use any other mobile devices or equipment in the same application area within the short distance to cause any interference. Signal interferes from TV and radio Sometimes, there will be some failure of data transmission and receiving which are caused by the signal interferes from TV and radio. Hybrid mode Under this mode, CYCLOPS II will transfer data automatically (similar to real mode). When it is out of Communication range or disconnection mode, it will save the data into memory after scanning and transfer the data according to the order of data saving completely after BT connection is ready again. Power Charging This device is built-in with Lithium Battery and not charged fully. Please Must charge it before the 1st time use under the temperature of 535. 1Charging with AC adapter:

You can start power charging through This AC port and mind the direction of Plug-in. 2Charging with USB cable:

You can also start power charging through AC cable connected with the PC USB port . The Ac cable one site is USB that can not transfer data from Cyclops II to PC only for power charge. It will take about 2.5hrs to charge full power with AC adapter. It will take about 3hrs to charge full power with connecting PC USB port. Please do not Charge power with the USB Hub Please use the specified AC Adapter in this box, it might cause charge failure or burn this device with the other adaptors. 3Power Charge Time Full Power Charge Time will change depending on the condition how you use and the battery status. 4There are about 300 times of Li battery charge and discharge power. The life of Li battery will change depending on the condition how you use. Please must stop using immediately if you find there are some situations as below which might be caused by device failure or unknown failure:

Power is full but it will turn off very soon after using. When Charging with AC adapter or USB cable, the device becomes very hot. Default Setup Value ModeReal mode Auto Power-OFF time3mins Device nameBTS700BT last address digitals AuthorizationNo BT profileHID EncryptionNo PIN Code0000 Time setupOFF RESET Back to Default Setup Value How to reset back to Default Setup Value When there is no way to delete the set-up values, we would like to suggest you to reset this device back to Default Value. Please read the setup barcode at the right side. As the memory setup data cannot be deleted, please try the other below way to initialize and delete it. When CYCLOPS II has been setup as reverse barcode scanner, please read reverse barcode at the right side. Memory Initialization Memory Initialization will delete all data and values in the memory. Please read the barcode at the right side which can make the memory initialized. Please note: that there is no way to get the data back after the memory is initialized. Simple ways to start CYCLOPS II 1Power Turn-on Press the scan button for 3 seconds to turn on and Scan Led will light up as well. After power is on, Scan Led will light off. 2Power Turn Off Automatically When the system is standing-by for a period of time, it will turn off automatically

(Default: 3mins). There is no power switch on CYCLOPS II to turn off. 3RESET Back to Default Setup Value by Hand Please press the RESET key when the power is on (it will turn off after resetting). Only when this machine is not working well, we would suggest you can use this way to reset. 4Bluetooth communication Before start Bluetooth communication, please make Paring connection with the other Bluetooth device. PIN default code is 0000. You can easily start connection through Bluetooth Host device and can be confirmed by the BT LED status. Also, You can read the setup barcode to switch mode to SPP master. 5Barcode scanning Please press the scan key to scan the Barcode. Barcode scanning can be confirmed by the Scan LED status. And read the setup barcode at the right side to confirm if CYCLOPS II is able to scan. Communication with iPadiPhone Under the default setup, you can use HID Profile to start BT Communication with iPad iPhone quickly. And you can also press the function key to show or hide the software keyboard. CYCLOPS Detailed Setting Guide On our below website, you can download the Detailed Setting Guide. Please carefully read the guide to understand all detailed explanations and ways on setup. http://www.bitatek.com.tw Since our Setting Guide can shown on PC monitor, CYCLOPS II can read these barcodes directly and set up accordingly So you do not have to print out this guide. However, it will be not easy to scan the barcode because of the light reflection on monitor or the barcode size. Duplication of Setup data You can easily duplicate the Setup data from one CYCLOPS II to the other CYCLOPS II scanners. This way will provide fast and correct Setup process for multiple data collectors. 1You can Setup the first one CYCLOPS II through scanning the Setting Guide. 2You can connect the first CYCLOPS II with the PC through USB cable to transfer the setup data to PC (SYSTEM.CFG file). 3Then You can connect the other CYCLOPS II with PC through USB cable to duplicate the setup data from PC. Long term Storage Please store this device under the dry condition (with few moisture) When the system is under the Batch mode and keeping off for a period of long time, it will be RESET the time after battery is without any power. Always charge before using CYCLOPS II and Please refer to the setting guide to set the date& time. How to discard this device This device is built-in with Lithium Battery and Lithium Battery is recyclable and important resource. If you send it back to our company, we will disassembly and recycle it. If you want to discard this device by yourself, please remember to pull out the battery and recycle it in the store you bought or the other related stores. The way to disassembly:

Remove the four screw plugs out of the case screw holes and pull out the screws. Open the case and Remove the screws to fix the battery then you can pull out the battery. Notice when you are disassembling :

Please tape the metal part of the battery and it will be insulated. Specification:

Model CPU Memory USB Bluetooth Scanner Clock function Power Supply I/O Interface AC Adapter Operation condition Storage condition Free Drop Sealing Regulatory Dimensions Weight Cyclops II Atmel AT91SAM9G25 400MHz 32 MB Flash ROM The max 8,000 data files (fixed data size: 2048 Byte including date& time ) can be saved. 128 MB SDRAM Yes, under Batch Mode only Ver.2.1+EDR Class210mincluding SPP/ HID Profile USB2.0 Full Speed CMOS Imager2DMotorola SE4710 soft decode Micro USB-B type Built-in Lithium Ion battery It will take about 2.5hrs to complete battery charge with AC adapter and Battery life about 8 hours ( QR code 256bytes ) scan1 Input 100240VAC 50/60Hz Output DC5V/2A, connector type: Micro USB Temperature 1050 ( charging temperature 535 Humidity 2085% without condensing Temperature Humidity 595%

-2560 1.5m2 drop, and 1.0 m Tumble Drop 100 Cycles IP level IP54 CE/ FCC About 50g 90Lmm 38Wmm 16Hmm 1 One scan per Six seconds under room temperature and Bluetooth connection. 2 Free drop on concrete, 3 times per 6 surface at room temperature Trademark Bluetooth & Logo is belonging to Bluetooth SIG, INC Trademark. iPadiPhone and iOS is belonging to Apple Inc. Trademark. ALL company name or logo appearing on this document are all intellectual property rights belonging to BITATEK CO.,LTD. All copy rights are reserved: without any agreement of our company, that is not allowed to copy or quote any part or all content of this document. Rev.1.0

Cyclops2 FOR CHANNEL 2 Bluetooth No. Label 4G32-BB000601 4G30-BB000101 LOGO Cyclops2 FOR CHANNEL Cyclops2 FOR CHANNEL 1.0 m m 8 3

. 2 1 2:1 1:1 17.20 mm m m 2 2

. 3

:pantone cool gray 6C Bita Data collector2 2D artwork 2013/09/26 Model No label for ALFCyclops m m 3

. 0 0 5

. 0 0.50 0.3mm 0.50 0.3mm 1:1 m m 3

. 0 0 5

. 0 2:1 White 0.50.5mm m m 1 1

. 4 23.60 0.20 3

0 2

. 0 0 0

. 1 R 0.15 Label prints slant should not over 0.5mm. 0 2

. 0 0 1

. 9 1 100% Size Print Reference R0.50 0.20-2 Vicki-lin Cyclops2 FOR CHANNEL Model No label for Data Collector 4G30-BB000101 1.0 23.6 7 1 3 5

0.1 Adhesive 2:1 Notes:

1. "o"is the control dimension of this part. 2. "p" is the checking dimension of this part. 3. Material: See table. 4. Color: See table. 5. Unspecified Tolerance: Please follow the tolerance table. 6. Scratch and burr follow QC cosmetic inspection spec (B3-QA-054). Cyclops2 FOR CHANNEL 4G60-BB001001 1.0 54.0 White 0

. 0 3 21mm m m 1 2 100% Size Print Reference Space between vertical line on left of the packing label and label edge should be 21mm;

Space between horizontal line on bottom of the packing label and label edge should be 21mm Cyclops2 FOR CHANNEL 4G60-BB001001 1.0 BATTERY CAUTION LABEL 120.0 0

. 0 1 1 100% Size Print Reference 1:1 Vicki-lin

*4G55-BB000601;

Cyclops2 FOR CHANNEL BATTERY CAUTION LABEL

() 4G30-BB000301 1.0 EXTERNAL PACKAGE LABEL 110.0 1:1 0

. 5 8 T Tolerance :

Vicki-lin 100% Size Print Reference Cyclops2 FOR CHANNEL 4G52-BB001801 1.0 Carton Lable List Carton Tape BATTERY CAUTION LABEL External package label L -type partition L L -type partition L 5 4 10 9 3 8 2 1 7 6 15 14 13 12 11 20 19 18 17 16 25 24 23 22 21 External package label BATTERY CAUTION LABEL

[2]

the opppsite side Carton Cyclops2 FOR CHANNEL Vicki-lin Packaging Box& Carton Lable List 1.0

BITATEK Co., Ltd. 6F., No.115, Wugone 3rd Rd. Wugu Dist. New Taipei City Date: 2014-09-12 FCC ID: SPYBTS002 Taiwan 248 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below:

Schematics Block Diagram Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours,

BITATEK Co., Ltd. 6F., No.115, Wugone 3rd Rd. Wugu Dist. New Taipei City Taiwan 248 Date: 2014-09-12 FCC ID: SPYBTS002 A U T H O R I Z A T I O N L E T T E R To whom it may concern:

We, the undersigned, hereby authorize Andrea Hsia / Senior Specialist of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all manners relating to FCC application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Andrea Hsia / Senior Specialist of BV CPS Taoyuan on our behalf shall have the same effect as acts of our own. If you have any questions regarding the authorization, please dont hesitate to contact us. Sincerely yours,