FCC ID: 2BD4W-82078 FAST FETCH

USER SAFETY Instruction Manual Item: 80278 20231026 Failure to follow instruction manual may result in accident and/or injury Please read this manual carefully before using Fast Fetch Do NOT leave Fast Fetch outside when not in use Fast Fetch is not waterproof; Do NOT use Fast Fetch in rainy, stormy, muddy, snowy or otherwise hazardous conditions SAFETY RECOMMENDATIONS:

Do NOT leave your pet unattended with Fast Fetch. Consult your veterinarian to be sure your pet is up for vigorous exercise. Fast Fetch is not recommended for young puppies. Carefully evaluate your pets condition after each round; Fast Fetch is vigorous exercise and not every pet is up for this type of activity. Watch your pet for signs of fatigue and stop whenever appropriate. Fast Fetch includes safety features to pause operation when the line is stepped on, grabbed or otherwise encounters resistance; Nevertheless, check your pet for signs of abrasion after play. Make sure the eld of play is free of obstacles, debris and other hazards such as open holes in the ground. Use the included tethers to anchor the drive unit and pulleys to the ground; Do NOT anchor the stakes directly into the holes in the drive unit and pulleys. Keep the manual safe for future reference. PLEASE READ!

90 Second Shut Off:

Fast Fetch will pause for 5 seconds after 90 seconds of active use to protect the motor and battery. During the pause the remote will automatically disconnect and reconnect to the drive unit. Stall Feature:

Fast Fetch will pause when it detects increased resistance such as when your dog steps on the moving line. Fast Fetch will beep after a short pause to indicate it is ready to continue. PARTS Remote Control FAST FETCH Drive Unit 3 Field Pulleys 2 Rolls Flags Nylon Cord Cord Winder 4 Ground Stakes + 2 Spares Charger Cable

(Battery Charger) Carry Bag Rechargeable Battery Battery Charger 4 Straps + 2 Spares SAFETY PRECAUTIONS Adult assembly and setup required; Adult supervision required at all times while Fast Fetch is in use. Only setup on level, well maintained areas Setup away from all structures, hazards and obstacles Do not touch the pulley or drive wheels while in use Minimum distance between each unit is 7 ft, Maximum distance between each unit is 33 ft. Make sure your unit battery is fully charged before rst use. Keep hands off the running Pulleys and the cord. DO NOT FLIP OVER THE FAST FETCH. Keep pets off and away from FAST FETCH when setting up. BATTERY CHARGING AND OPERATION Battery Charger Input Voltage: 100-240V AC Output Current: 3 X 800mA Removable Rechargeable Battery Type: Li-ion battery Voltage: 11.1V Battery Capacity: 2,500mAh Charging Lead-time: 6 hours Plug into electrical outlet to power Battery Charger 4 Pins Rechargeable Battery 3 LED indicates battery charge level White plug White plug for charging Orange plug connects to the Drive Unit IMPORTANT!

Never use the charger unsupervised. Note! Leaving the battery connected after it is fully charged may result in one or more of the lights turning red again - the battery is fully charged at this point, please try to remove the battery from the charger once fully charged. If all three lights have not turned green after 6 hours on the charger. The battery is fully charged once all three of the lights turn green. Only connect the battery to the charger using the white plug. Pay attention to the alignment of the plug to the charger. Do NOT force the plug into the charger. Disconnect the battery from the charger when fully charged. Rechargeable batteries are only to be charged under adult supervision. Battery Charger Installing the Battery 1. Fully charge battery before use. 2. Slide open the battery door at the rear of the Drive Unit. 3. Connect the battery using the orange plug;

White plug will be left disconnected. 4. Position the battery in the battery compartment and slide the door closed. SETTING UP FAST FETCH 1. Place the drive and pulley units in a square or rectangular layout. 2. Anchor the pulley units to the ground by rst connecting a strap to the rear of the unit, then staking the strap to the ground; Do not stake down the drive unit yet. 3. Open the caps to each unit and extend the line around each pulley. Cut the line leaving enough to tie the two loose ends together. Tie the loose ends together and close the caps to each unit. 4. Adjust the position of the drive unit to add tension to the line. The line should no longer be loose or lying on the ground. Do not over tension the line because it will cause the motor to stall. 5. Tear off a ag from the foll and tie it to a free spot on the line. We recommend testing the unit before bringing your dog out to play. Try different levels of line tension by adjusting the position of the drive unit to see what works best for your area. Tie the strap on the hole, stake though the hole. Driver Cord Pulley Pulley Pulley Recommend distance between each unit Maximum length: 33 FT (10m) Minimum length: 7 FT (2.1m) Speed Control button Release to Stop Low High Requires 2 x AA Batteries

(Batteries Included) HOW TO CHANGE BATTERIES 1. Remove the battery box door by screwdriver (not included). 2. Replace old batteries with 2x fresh AA (2x1.5V) batteries and then close the battery door. 1.5V/AA/LR6/AM3 1.5V/AA/LR6/AM3 LED Power ON/OFF OPERATION OF REMOTE CONTROL 1. Remove the battery box doors insulator 2. Use the screwdriver (not included) to lock the battery box door 3. Press the ON button on the driver 4. Press once ON/OFF button, Green LED (ashes 3 times) + vibrate 5. When LED turned solid Green, the remote connected with driver 6. To change the speed by pressing the speed button, press harder, the drivers speed turn faster 7. After 90 seconds, it will shut off, it will pause for 5 seconds after 90 seconds of active use to protect the motor and battery. During the pause the remote will automatically disconnect and reconnect to driver. 8. Turn Off, Hold the ON/OFF for 3 seconds, LED will be off. The remote will disconnect with the driver. Remote Control LED Indication DESCRIPTION SIGNAL Power ON the remote Green LED (ashes 3 times) + vibrate Signal Pairing Ready to use Shut Down Flashing green LED Solid Green LED Red LED (ashes 2 times) + vibrate CAUTION:

Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc.) batteries. Do not dispose of batteries in a re as batteries may explode or leak. Do not short-circuit the batteries. Do not attempt to recharge non-rechargeable batteries. Remove batteries if the product will not be used for an extended period of time. Use a screwdriver to open the battery compartment door and replace old batteries. Non-rechargeable batteries are not to be recharged. Exhausted batteries are to be removed from the toy. The supply terminals are not to be short-circuited. Batteries are to be inserted with the correct polarity (+ and -). Batteries are to be handled by an adult only. Batteries are to be inserted with the correct polarity as shown on the battery compartment. Ensure battery compartment is secure before use. Only batteries of the same or equivalent type as recommended are to be used. Warning and Caution of the Li-ion Battery:

THIS PRODUCT CONTAINS LI-ION BATTERY 11.1V / 2,500mAh Li-ion battery has a severe risk of re and injury if it is improperly handled or misused. Read all enclosed instructions, warnings and precautions regarding the care, use and disposed of Li-ion battery. The enclosed Li-ion battery is only to be used with the shower and charger included with this product. Keep away from ammable materials. Do not place in res or leave in hot places. Never throw battery in a re or attempt to open outer casing. Charging cord used with the FAST FETCH is to be regularly examined for damage to the cord, plug, enclosure and other parts. In the event of such damage, it must not be used until the damage has been repaired. Li-ion battery disposal: Li-ion battery must be recycled or disposed of properly. They should not be disposed of with other correct recycling and/or battery disposal. Do not expose to direct sunlight. Keep dry after use. Rechargeable battery is only to be charged by adults. FCC NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Produced by Black Swan Manufacturing Inc. Richmond, B.C. V6X 4K1, Canada Made in China

Summary ITEM Model Name Center Frequency MAX. Gain Polarization Azimuth Beam Pattern Impedance Antenna Length Manufacture Address Inverted F Antenna Specification ANT SPEC 2.4G ANT Horizontal Vertical 2400MHz 2450MHz 2500MHz 2400MHz 2450MHz 2500MHz

-1.26

-0.76

-0.58

-5.25

-2.46

-1.86

-0.58dB Horizontal and Vertical Omni-directional 50 Ohm 11.1mm ZHUHAI JIELI TECHNOLOGY CO.,LTD 333 Kexing Road, Xiangzhou District, Zhuhai City Antenna Photo & Length (mm) Horizontal: 2400 MHz 2450 MHz 2500 MHz Power (dBm) Max: 0 Min: -40 Scale: 5/div Frequency

(MHz) 2400 2450 2500 Max

-1.26174

-0.765802

-0.585582 Gain(dB) Min

-30.0801

-36.5604

-22.0315 Avg

-7.18716

-7.48023

-6.59127 Vertical: 2400 MHz 2450 MHz 2500 MHz Power (dBm) Max: 0 Min: -30 Scale: 5/div Frequency

(MHz) 2400 2450 2500 Max

-5.2537

-2.4652

-1.86120 Gain(dB) Min

-22.1424

-24.5837

-29.5214 Avg

-12.4294

-10.4702

-9.20432 ANT Test LabsAttestation of Global Compliance Co., Ltd.

Black Swan Manufacturing Inc. Date: Jan. 03, 2024 Product Model Number: 82078 FCC ID: 2BD4W-82078 To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following:

Testing Approval applications and procedures We declare that ORGANIZATION. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by ORGANIZATION. on our behalf shall have the same effect as acts of our own. By:

Contact Listed on FCC Wesbite Title: QA Email: chenzzh@zixinteco.cn Telephone: 852-3590-6409 On behalf of: 227-8680 Cambie Road, Richmond, BC V6X4K1, Canada Effective Date: April 2, 2020 Revision Date:

QSF 7.6.4-8 Agent Authorization Letter Template Revision: 0 Page 1 of 1

Black Swan Manufacturing Inc. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject; Request for Confidentiality FCC ID: 2BD4W-82078 To Whom It May Concern, Date: January 3, 2024 Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Software Security Requirements for UNII devices In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Leo Siu Title: QA

Black Swan Manufacturing Inc. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2024-01-03 FCC ID: 2BD4W-82078 Ref. #1: Attestation Statements Part 2.911(d)(5)(i) Filing Black Swan Manufacturing Inc. certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Ref. #2: Attestation Statements Part 2.911(d)(5)(ii) Filing Black Swan Manufacturing Inc. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Applicant: Black Swan Manufacturing Inc. Address: 227-8680 Cambie Road, Richmond, BC V6X4K1, Canada Contact Person: Leo Siu Tel.: 852-3590-6409 Email: chenzzh@zixinteco.cn Sincerely, Signature:

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/7059279.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case US Age ent for Se ervice of P Process L LETTER OF F ATTEST TATION TO:

Office Feder 7435 Colum e of Enginee ral Commun 5 Oakland Mi mbia, MD 21 1046 ering Techno ications Com lls Road ology mmission US A Agent for Se ervice of Pr rocess:

CLF Import a and Export L Limited Comp FRN:0 Conta Addre Telep Email EIN:9 pany Name:

0033489683 act Name: Da ess: 1312 17 phone No: (9 l:market@clf 98-1720547 avid chen 7th Street #6 949) 254-256 fimportexpor 692Denver 65 rt.com r, CO 80202, United State es This l a loca letter is to co al representa onfirm that t ative on beha the US Agent alf ofBlack Sw t for Service wan Manufac of Process a cturing Inc. accepts resp onsibility to act as The U outlin 2.9 US Agent fo ned in the FC 11. r Service of CC Equipmen Process is a nt Authorizat aware of and tion Program d agrees to c

, Report and comply with d Order FCC the require 22-84, and c ments clause Black Swan M on:FAST FET Manufacturing TCH g Inc. Appl Comp Produ FRN:0 Grant FCC I Cont Addre Telep Email icant:

pany name:B uct Descriptio 0034613950 tee code:2BD ID:2BD4W-8 tact Name:

ess:227-8680 phone No: 85 l:chenzzh@z D4W 2078 Leo Siu 0 Cambie Ro 52-3590-640 zixinteco.cn oad, Richmon 9 nd, BC V6X4K K1, Canada The A Equip Applicant is pment Autho aware of a rization Prog nd agrees to gram, Report o comply w t and Order F ith the requ FCC 22-84, a uirements ou and clause utlined in the 2.911. e FCC This Agreement t is valid un ntil (Perman nently valid d). Date Appl e: 2024/01/

icants Nam

/15 me:Leo Siu US Ag gent for Se rvice of Pro ocesss Nam me:

Title Signa

:QA ature Title:

Signa Manager ature 1/1