FCC ID: 2AXXF-ITEMP ITEMP

Manual company name BlueBeard Studio Brand story About iTemp Smart Mug/Bowl Using 304 stainless steel LED indicator iTemp Coaster Touch sensor Light:

Temperature matters when it comes to making drinks and food. Proper temperature can bring out the best of the ingredients. Oftentimes, were too busy getting on with our lives, we neglect the subtle nuances that matters. How to keep enjoying your hot drink or food at the exact temperature you prefer, so l ife can become more delightful during the daily routine?

That's what iTemp is for, always setting the perfect temperature of your drinks and m ore. iTemp will keep your drink or food at your preferred temperature, whether to heat up, cool down with the proper temperature you like. Lifes just so much better with a li ttle bit of warmthiTemp, the temperature expert with the ultimate Smart Mug and B owl. Bluetooth pairing: white LED flashing Constant temperature: white LED flashingfast Bluetooth pairing failed: red LED flashing Waiting for injection: red LED flashing The temperature is too hot: red LED on until the temperature is normal How to connect iTemp to your smart device 1.Place the Mug/Bowl on the coaster and make sure the Coaster is already plugg ed in. 2.Open the iTemp App on your device. Hold the button on the Coaster for 10 se c till you feel the vibration. 3.Do Not refill Mug/Bowl when it is placed on the Coaster. iTemp App:

1. Adjust your favorite temperature Swipe to select the food or beverages on app, like coffee, milk or tea, from left to the right. eg. Set your desired drinking temperature for your coffee by adjusting the temp bar. Precision at your fingertips and make temperature adjustment you like. Double-tap to The next time simply double-tap the iTemp Coaster, itll start heating up until it reaches y activate!

our setting. No more fumbling with the app. 2.Programmable heating alarm Pair with the iTemp app for heating at all times, customise presets, receive notifica tions when it is ready. 3.Hydration Tracking The built-in weight sensor detects how much volume of water is consumed. A weekly chart breaks down your water consumption and average drinking temperature. Youll be able t o monitor your hydration level at all times. iTempcare and maintenance py water. You may apply a soft sponge and hand wash your Smart Mug/Bowl with warm and soa After washing, dry off your Mug/Bowl completely before placing it on the charger. Warning: The iTemp Coaster cannot be washed. Wipe it with a kitchen towel or wet wipes. Keeping it dry and clean is recommended.

*Hand washes only. Do not use dip wash or dishwasher to clean your Mug/Bowl.*

Precautions 1.Make sure your iTemp Coaster is stably placed on a coffee counter or tabl e. 2.Do not place your Coaster or power cords on heating elements. 3.Do not use other sources to heat up the product. 4.Do not dip wash the Coaster and do not soak it with water. 5.Do not use it on the Coaster when your Mug/Bowl is empty. 6.When the content is overheated, the LED indicator will be red until the te mperature is normal. 7.If the Bluetooth pairing fails, the LED indicator will flash twice (red li ght). spec material CoasterABS/PC MugABS/304 stainless steel BowlABS/304 stainless steel capacity Mug310ml Bowl650ml weight Coaster175g Mug373g Bowl555g size Coasterhigh 25.5mm/diameter 160mm Mughigh 113mm/diameter 81.4mm/width with handle 106mm Bowlhigh 94mm/diameter 155mm temperature range Jet Black/Pearl White 25~65C 77~149F color input 100~240V power 61.75W manufacturer name BlueBeard Studio address contact product@itemp-bbs.com warranty LEGAL INFORMATION 6F., No. 86, Sec. 1, Xinhai Rd., Daan Dist., Taipei City 106, Taiwan (R.O.C.) iTemp Warranty Service is provided for all iTemp purchased directly from a BlueBeard S tudio store or from an official BlueBeard Studio retailer. Warranty service does not extend to iTemp repurchased from another seller or from a t hird party. BlueBeard Studio grants a standard period of 1-year full warranty on all parts. The warra nty period starts from the date shown on the customers purchase invoice. For a warra nty claim to be valid (i) notification must be made before the end of the warranty perio d; (ii) conform to any additional stipulations of the warranty period, as defined below; (ii i) must be substantiated with original proof of purchase, including the purchase invoice and the warranty card. CONDITIONS In the event of material or manufacturing defects, BlueBeard Studio is obliged to rectify the defects free of charge according to iTemp warranty conditions. If the defect cannot be repaired, BlueBeard Studio will, within the warranty period, replace the product free of charge by an identical product. The iTemp warranty is granted under the explicit condition that iTemps installation an d maintenance instructions have been observed. Unless the booklet contains do-it-yo urself assembly instructions for the product or part thereof and these have been follo wed up meticulously, the warranty will become invalidated if the product was at any tim e disassembled or reassembled by persons not authorized and confirmed by BlueBeard Studio to be qualified. The iTemp product must have been sold, delivered and assemble d by BlueBeard Studio. The iTemp warranty does not cover any defects or damage caus ed by inappropriate use, incorrect or improper use, or normal wear and tear. If any iTem p product is combined with a product not manufactured by BlueBeard Studio, the warra nty may be restricted or declared void. Any warranty claim must first be recognized as justified, by BlueBeard Studio. Depending on the country, the warranty may not automatically include cost incurred fo r shipping defective products for iTemp for scrutiny and/or repair, nor for shipping cost of replacement or repaired product(s) back to claimant. Within the warranty period repa ir itself, however, will be free of charge. Since customers will only be entitled to make a warranty claim on submission of the ori ginal invoice, we advise that both the invoice and warranty card are kept in a safe place. Only the original purchaser is entitled to claim warranty. The warranty period is limited to the lifetime of the first original purchaser. PROCESS FCC Warning two conditions:

OTHER WARRANTY CONDITIONS If a part is repaired or replaced during the warranty period, the (extended) warranty peri od still remaining for the entire product will apply to this part. To report a defect, send an email to product@itemp-bbs.com. If the problem cannot be solved by email, you will be told to send an iTemp to the following address6F., No. 86, Sec. 1, Xinhai Rd., Daan Dist., Taipei City 106, Taiwan (R.O.C.). This device complies with Part 15 of the FCC Rules. Operation is subject to the following

(1) This device may not cause harmful interference, and (2) this device must accept any i nterference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provi de reasonable protection against harmful interference in a residential installation. This e quipment generates, uses and can radiate radio frequency energy and, if not installed a nd used in accordance with the instructions, may cause harmful interference to radio co mmunications. However, there is no guarantee that interference will not occur in a parti cular installation. If this equipment does cause harmful interference to radio or televisio n reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the recei ver is connected.

-Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party r esponsible for compliance could void the user's authority to operate the equipment.

Label location Size:5*10mm M/N: ITEMP-A01 FCC ID: 2AXXF-ITEMP This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

BlueBeard Studio Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 2020-09-24 Subject: Request for Confidentiality FCC ID: 2AXXF-ITEMP To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Long-Term Confidentiality Short-Term Confidentiality NOTE 2 Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info No No No No No No No No No No No No No No No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Pual Li Title: Manager 1/1

BlueBeard Studio Co., Ltd. Letter of Authorization Company: BlueBeard Studio Co., Ltd. Address: 6F., No. 86, Sec. 1, Xinhai Rd., Daan Dist., Taipei City 106, Taiwan Product Name: ITEMP Model Number: ITEMP-A01 FCC Identifier: 2AXXF-ITEMP We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Pual Li Title: Manager Signature of applicant:

Date: 2020-09-24 1/1