BlueCats Bluetooth Low Energy Module Datasheet Thursday, 5 April 2016 Version 1.0 BC010 Features 4 Mbit External Flash (SPI) No external components required Reverse Polarity Protection built in Meandering Inverted-F PCB Trace Antenna Can be surface mounted to a daughter board or used in stand alone fashion 15.21 Statement - for all intentional and unintentional radiators. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 15.105 statement (for digital devices) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radi-ate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This module is exempt from SAR testing for all portable 2 applications when it is not co-located with any other transmitter and when it is the only antenna in a host device. Therefore this module can be placed <5 cm from a person. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Cet quipement est conforme aux limites d'exposition aux radiations FCC dfinies pour un environnement non contrl. Ce module est exempt de tests SAR pour toutes les applications portables lorsqu'ils ne sont pas co-
implant avec un autre metteur et quand il est la seule antenne dans un dispositif hte. Par consquent, ce module peut tre plac < 5 cm d'une personne. CAN ICES-3 (B)/NMB-3(B) BlueCats Australia Pty Ltd, BlueCats, assumes no responsibility for any errors that may appear in this document. BlueCats reserves the right to alter the hardware, software, and/or specifications detailed here at any time without notice and does not make any commitment to update the information contained here. 3 Version History Version Comment 1.0 Preliminary datasheet 4 Table of Contents 1. Pinout and Terminal Descriptions ................................................................ 6 2. Connector Recommendations ......... Error! Bookmark not defined. 3. Electrical Characteristics ................................................................................... 8 3.1 Absolute Maximum Ratings .......................................................................................... 8 3.2 Recommended Operating Conditions....................................................................... 8 4. Physical Dimensions ............................................................................................ 9 5. Antenna Characteristics ................................................................................... 12 6. Design Considerations ........................ Error! Bookmark not defined. 5 1. Pinout and Terminal Descriptions 6 324516789101112132324141516171819202122TOP THROUGH VIEWBC010 PIN Numbers1611523456789101112131414119753216131512108641AMBLKJHGFEDCCAJFKMDBLHGEDRAWNCHK'DAPPV'DMFGQ.AUNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERSSURFACE FINISH:TOLERANCES: LINEAR: ANGULAR:FINISH:DEBURR AND BREAK SHARP EDGESNAMESIGNATUREDATEMATERIAL:DO NOT SCALE DRAWINGREVISIONTITLE:DWG NO.SCALE:10:1SHEET 1 OF 1A1WEIGHT: BC010_pcb_2015_pin_numbers BC010 Pin BC010 Name 1 D1 2 D0 3 D2 4 GND 5 D3_SDA 6 D4_SCL 7 VDDS 8 TMS 9 TCK 10 TDO 11 TDI 12 nRESET 13 VDD_EB 14 GND 15 GND 16 GND 17 D12 18 D11 19 D7_MOSI 20 D8_SCK 21 D10_MISO 22 D9_CS 23 GND 24 GND Description Digital I/O Digital I/O Digital I/O CC2640 DIO_1 DIO_0 DIO_2 GND DIO_3 DIO_4 PWR JTAG_TMSC Programming/debug JTAG_TCKC Programming/debug Programming/debug DIO_5 DIO_6 Programming/debug RESET_N Digital I/O Digital I/O External Voltage supply DIO_12 DIO_11 DIO_7 DIO_8 DIO_10 DIO_9 Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O 7 3. Electrical Characteristics 3.1 Absolute Maximum Ratings Parameter VDD_EB Storage Temperature Min
-0.3
-40 3.2 Recommended Operating Conditions Parameter VDD_EB Operating Temperature Min 2.3
-40 Max 4.1
+85 Max 3.8
+85 Unit V C Unit V C 8 4. Physical Dimensions Figure 1: BC010 Overall Dimensions 9 12.9614.8819.376.7311.640.601.30 10 1.811.782.602.608.568.013.451.251.801.801.500.500.805.231.251.50119.3714.88TOP THROUGH VIEWAll linear dimensions in millimeters1.This drawing is subject to change without notice2.BlueCats BC010 pin locations1611523456789101112131414119753216131512108641AMBLKJHGFEDCCAJFKMDBLHGEDRAWNCHK'DAPPV'DMFGQ.AUNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERSSURFACE FINISH:TOLERANCES: LINEAR: ANGULAR:FINISH:DEBURR AND BREAK SHARP EDGESNAMESIGNATUREDATEMATERIAL:DO NOT SCALE DRAWINGREVISIONTITLE:DWG NO.SCALE:20:1SHEET 1 OF 1A1WEIGHT: BC010_pcb_2015 11 2.702.7011.284.501.096.206.761.100.600.800.607.850.05115.8415.98Antenna KeepoutAll linear dimensions in millimetersThis drawing is subject to change without noticeBC010 Land Pattern DataExample Non-Soldermask Defined PadTOP VIEW1611523456789101112131414119753216131512108641AMBLKJHGFEDCCAJFKMDBLHGEDRAWNCHK'DAPPV'DMFGQ.AUNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERSSURFACE FINISH:TOLERANCES: LINEAR: ANGULAR:FINISH:DEBURR AND BREAK SHARP EDGESNAMESIGNATUREDATEMATERIAL:DO NOT SCALE DRAWINGREVISIONTITLE:DWG NO.SCALE:10:1SHEET 1 OF 1A1WEIGHT: recommended_footprint_nomask 5. Antenna Characteristics Figure 2: Elevation #1 Antenna Pattern 12 Figure 3: Elevation #2 Antenna Patter 13 Figure 4: Azimuth Antenna Pattern 14