Users Manual Electro-Voice Model REV-PH Handheld Wireless Microphone Transmitter The Electro-Voice (Ev) REV-PH is a Professional Grade Wireless Handheld Transmitter operating in the UHF frequency range. The REV-PH combines frequency agility and ease of use like no other. The transmitter operates within a 24 MHz wide segment in 25 KHz steps. The high quality audio circuitry and advanced Radio Frequency (RF) signal processing offer broadcast quality signal-to-noise and audio clarity. The typical line-of-
sight distances for the system may be up to 300 feet. System features include:
Internal Half Wave Dipole Antenna. Durable Painted Molded Handle. Permanent Flash Memory for frequency/setting storage. On-Loc prevents accidental power off (when set). LCD Display for ease of viewing. Page 1 REV-PH Controls and Connections:
1. Main Display LCD. 2. Red low battery LED indicator 3. Power On/Off Switch 4. SET Control Button 5. Channel / Frequency Up Switch 6. Channel / Frequency Down Switch 7. Microphone Element 8. 9V Battery Compartment 9. Battery Cover Screw Type Page 2 Quick set-up:
1. With the Power Switch on the transmitter OFF, install fresh batteries into the transmitter. 2. To prevent feedback or unintentional noise, mute the audio mixer/amplifier or other device during set-up adjustments. Place the transmitter Power Switch to the ON position. 3. The operating screen (display) light will come on momentarily. The display will show the current frequency group and channel. Note: Anytime Power is removed and turned back on, the GP/CH screen will be displayed. The Low Battery light will flash momentarily. 4. If the Group and Channel match the desired receiver group and channel, proceed to Step 11. If not, proceed to Step 5. 5. To select a different GP/CH, press SET one time. The Group will start flashing. Use the up and down arrows to change the group number. Press the SET button to save the Group. 6. After setting the Group, The Channel number will start flashing . Use the up/down arrows to change the Channel number. Press SET and the channel is now saved. 7. There are 18 Groups and up to 16 Channels (preferred groups/channels) stored in memory. If desired, you can create new groups/ channels but you must change to a new frequency to store in that group/channel. 8. In order to select a new frequency, you must have a users group
/channel selected. Press the SET button. The Group should be flashing. Press the Up arrow until group 19u (user programmable) is found.
(group 20u can also be used) Press SET. The Channel should now be flashing. Select a channel with the up/down arrow. Press SET. 9. You are now ready to select a frequency to store in the users group above. Press and hold the set and down arrows at the same time for 3 seconds and release to go to the next screen function. Page 3 10. The next screen displays the operating frequency of the group/channel. If there is no frequency currently stored in the selected users group/channel, a dashed line will be shown. Press SET. The dashed line or frequency will start flashing. Press the up arrow one step at a time to find the desired frequency or hold down the up arrow to scroll through the frequencies quickly. The frequencies can be scrolled either way by the up/down buttons. When the desired frequency is showing, press SET. 11. Press the set and down arrows at the same time then release to go to the next screen function. 12. The next screen shows the battery level in % (percent). Press the set and down arrows at the same time then release to go to the next screen. 13. The next screen shows the audio setting. The display is shown in dB. 0 dB is (maximum volume), -27 dB is (minimum volume). Press the set and down arrows at the same time then release to go to the next screen. Setting the attenuator for the maximum Audio Meter reading on the receiver without peak distortion will produce the best signal to noise ratio. 14. The next screen shows the transmitter RF level (Lo or Hi). Press the Set button if you wish to change the RF level. Press the up button to go to Hi or the down button to go to Lo. Press Set to store. The transmitter RF is normally shipped set to Lo for use with multiple frequency systems and the best battery life.Hi power can be selected for longer distances or to suppress noise or interference. The nominal power in Hi is 50 milliwatts. 15. Press the set and down arrows at the same time then release to go to the next screen function, which will return to the Gp/Ch screen. The display screen will automatically show the Gp/Ch screen when the transmitter is first turned on. 16. When power off is required, simply place the power Off-On switch in the OFF position. The display will then delay slightly to allow the receiver to shut down quietly. Page 4 REV-PH Specifications:
RF Frequency range...512.0 to 536.0 MHz. RF Channel Step... 25 KHz. RF Power.. Norm, 5 mW, High, 50 mW (typical). Modulation.... FM, 40 KHz Deviation nominal. Audio Frequency Response...80-15000 Hz +/- 2 dB. Audio attenuator Range 27 dB. Microphones ( Dynamic).. 150 Ohms. Antenna..... Internal Half Wave. Power Two AA Batteries. Battery Life (9 Volt Alkaline)...8-10 Hours Typical. Approval Information:
(English) The Electro-Voice REV-PH Transmitter is Type Accepted under United States Federal Communications Commission CFR 47, Part 74 and Certified to Industry Canada RSS-
123. The device also complies with CRF 47, Part 15 of the FCC Rules and Industry Canada ICES-003 rules. Operation is subject to the following conditions:
1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. 3. Use only the manufacturer or dealer supplied accessories for this device. 4. This device must not be co-located or operated in conjunction with any other antenna or transmitter. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Licensing of Electro-Voice equipment is the users responsibility and licensability depends upon the users classification, users application and frequency selected. Bosch Security Sysetms, Inc., strongly urges the user to contact the appropriate telecommunications authority for any desired clarification. This Class B digital apparatus complies with Canadian ICES-003. Page 5 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which Increase the separation between the equipment and receiver. the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
(French) Le Electro-Voice REV-PH metteur est Type accept aux termes des tats-Unis de la Federal Communications Commission CFR 47, partie 74 et certifi Industrie Canada RSS-123. Le dispositif est galement conforme CRF 47, partie 15 des rgles de la FCC et Industrie Canada NMB-003 des rgles. Son fonctionnement est soumis aux conditions suivantes:
1. Le dispositif ne doit pas causer d'interfrences nuisibles. 2. Cet appareil doit accepter toute interfrence reue, y compris les interfrences qui peuvent perturber le fonctionnement. 3. Utilisez uniquement le fabricant ou le revendeur accessoires fournis avec cet appareil. 4. Ce dispositif ne doit pas tre co-implants ou exploits en conjonction avec une autre antenne ou transmetteur. ATTENTION: Les changements ou modififications cet appareil sans expressment approuve par la partie responsable de conformit pourraient annuler l'autorit de l'utilisateur de faire fonctionner cet quipement. Attribution de licences Electro-Voice quipement est la responsabilit de l'utilisateur et elle dpend la classification de l'utilisateur, l'application utilisateur et de la frquence slectionne. Bosch Security Sysetms, Inc, exhorte l'utilisateur de communiquer avec l'autorit de tlcommunications appropris pour toute prcision souhaite. Cet appariel numrique de la classe B est conforme la norme NMB-003 du Canada. Page 6 Conformit aux normes FCC Cet quipement a t test et trouv conforme aux limites pour un dispositif numrique de classe B, conformment la Partie 15 des rglements de la FCC et NMB-003 canadien. Ces limites sont conues pour fournir une protection raisonnable contre les interfrences nuisibles dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre des frquences radio et, s'il n'est pas install et utilis conformment ment aux instructions du fabricant, peut causer des interferences nuisibles aux communications radio. Rien ne garantit cependant que l'interfrence ne se produira pas dans une installation particulire. Si cet quipement provoque des interfrences nuisibles la rception radio ou de tlvision, qui peut tre dtermin en comparant et en l'teignant, l'utilisateur est encourag essayer de corriger les interfrence par une ou plusieurs des mesures suivantes:
Rorienter ou dplacer l'antenne de rception. Augmenter la distance entre l'quipement et le rcepteur. Branchez l'appareil dans une prise sur un circuit diffrent de celui auquel le Consultez votre revendeur ou un technicien radio / TV pour rcepteur est connect. assistance.Avertissement Page 7