NM-DB-2 Rugged/Military grade 2.4GHz 2x2 MIMO Wi-Fi Radio Transceivers Features Qualcomm-Atheros AR9590-AR1B Chipset with Extended Temperature Range Up to 300 Mbps Throughput with 2x2 MIMO Technology Calibrated High Power 2.4 GHz (27 dBm) Supported Ath9k Linux Driver MiniPCIE Interface TECHNICAL SPECIFICATIONS Model No. MAC Chipset Software Support Center Frequency Range Channel Bandwidth*
Radio Modulation (Dynamic Link Adaptation) Data Rates Supported 802.11n version 2.0 Capabilities Operating Modes MAC Protocol Wireless Error Correction Wireless Data Security NM-DB-2 Qualcomm Atheros QCA9590-AR1B with Extended Temperature range for Outdoor and Rugged models) Linux Drivers ath9k 2.412 GHz ~ 2.462 GHz This varies by the regulatory domain 20, 40 MHz channels CCK, BPSK, QPSK, 16 QAM, and 64 QAM (2.4 GHz 11n models) 802.11n: MCS0-15 (2.4 GHz) 802.11b/g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48 and 54 Mbps (2.4 GHz) Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx), Maximal 802.11 dynamic frequency selection as an AP and Client 802.11n and b/g Beam Forming ratio combining (MRC), Cyclic shift diversity (CSD), Frame aggregation, block ACK,Spatial multiplexing, cyclic-delay diversity (CDD), low-density parity check
(LDPC), Space Time Block Code (STBC) Phy data rates up to 450 Mbps (40 MHz channel) AP, STA and Adhoc modes to implement Point to Point, Point to multi Point TDD with Carrier Sense Multiple Access with Collision Avoidance
(CSMA/CA) FEC, ARQ 128 bit AES, WEP, TKIP and WAPI hardware encryption. Support for 802.11b, g, n and time stamp standards Loop back mode to facilitate FIPS AES certification, Small packet size
(96 bytes) in AES encryption at full packet rate
(Typ) Radio Modulation Coding Rate Rx Sensitivity Tx Power
(2dBm)2 FIPS Certification Tx/Rx Specification 2.4 GHz (20 MHz Channel) 802.11b, STBC 1 Mbps 802.11g, STBC 64 QAM 802.11n, MIMO BPSK 802.11n, MIMO 16 QAM 802.11n, MIMO 64 QAM 2.4 GHz (40 MHz Channel) 802.11n, MIMO BPSK 802.11n, MIMO 16 QAM 802.11n, MIMO 64 QAM Note 1 It is advantageous to use the smallest Channel Bandwidth that can support the Throughput requirements. Smaller bandwidths provide more channels to choose and help avoid interference issues. The systems SNR is higher at smaller Channel Bandwidths and Range is longer. Note 2 Max allowed Tx power depends on the regulatory domain CCK 3/4 1/2 3/4 5/6
-100
-80
-92
-82
-72 27 22 27 25 22
-90
-79
-70 1/2 3/4 5/6 27 25 22 Antenna Signal Strength
-35 to -85 dBm (Recommended), Absolute Maximum=+12 dBm Antenna port isolation for concurrent operation Up to +5 dBm signal strength for 2.4 GHz signal
>20 KV (Human Body Model)
>10 dB Integrated Antenna Port Protection Receiver LNA Gain Receiver Adjacent Channel Rejection (ACR) Receiver Alternate Channel Rejection (ALCR) Receive chain Noise Figure Transmitter Adjacent Channel Leakage power Ratio (ACLR) 45 dB (Fc ChBW) Transmitter Spurious Emission Suppression
-40 dBc
+6 dB
>18 dB @ 11g, 6 Mbps (Typ)
>35 dB @ 11g, 6 Mbps (Typ) RF Power control In 0.5 dBm steps. Accuracy of power calibration loop 2 dBm. Each transceiver individually calibrated and tested. Pin 20 of miniPCI-E interface. (Required for FAA compliance) RF Hardware Disable (RF Kill) Control for External Power Amp Spectral Analysis PHYSICAL, ENVIRONMENTAL AND OTHER SPECIFICATIONS Antenna Ports Host Interface Available as an optional configuration 8 bit resolution spectral FFTs available for software analysis 2 Ports (50 Ohms) with MMCX connectors. miniPCI-Express 1.2 Standard Any CPU board with Industry standard miniPCI-Express interface with minimum 6 mm connector height 3.3 Volts from miniPCI-Express connector 4W @ Max power, in continuous data transfer mode on all chains 2.8W @ 25 dBm power, in continuous data transfer mode on all chains 2W @ 20 dBm power (ETSI max), in continuous data transfer mode on all chains 0.7W in continuous data receive mode 230 mW in Sleep mode
-40C to +80C The Systems thermal design should ensure that the transceivers case temperature is maintained within these specifications. 0% 95% (Non-condensing) 30 x 50 x 7 mm, 14 grams Mechanical drawing and 3D-CAD files available upon request Designed and Verified to meet various regulatory requirements. Formal testing and approval is required based on the Integrators particular host platform and antenna type. The Integrator is also responsible for obtaining all required regulatory approvals in target markets for the finished product. 2ATBY-NMDB-2 Q3 2016 Q3 2016 Yes. 100% Recyclable/Biodegradable packaging Host CPU Board Operating Voltage Power Consumption Shield case temperature range (Operating) Humidity (Operating) Dimensions Regulatory Requirements FCC ID CE/ETSI Industry Canada (IC) RoHS/WEEE Compliance Singapore:
Doodle Labs (SG) Pte. Ltd. 150 Kampong Ampat KA Center, Suite 05-03 Singapore 368324 Tel: +65 6253 0100 USA:
Doodle Labs LLC 2 Mattawang Drive Somerset, NJ 08873 Tel: +1 862 345 6781 Fax: +65 6353 5564