Installation manual Assembly of RFID-Reader 70615 / 70616 Dok.-Reg-Nr.:
PR709_2 Page 1 of 3 Scope:
TEE Material-Number:
70615 / 70616 Name :
Date :
Author R. Flad 09.07.2018 Signature :
1. PURPOSE Team-leader M. Neher Quality-management V. Merz This document describes the detailed installation procedure of the RFID Reader modules E225_RFID_Bipo and E225_RFID_Mono 2. PROCEDURE 2.1. USED MATERIALS:
Tools Torx T10 E225_RFID_Bipo E225_RFID_Mono Linsen.k.schraube m. Torx M3 x20 St.verz Foto SAP-Nr.
-
-
-
-
-
70615 70616 10876 2.2. DETAILED DESCRIPTION:
Nr. Description Foto Used Equipment 2.2.1. Insert E225_RFID_Mono 70616 into socket-slots and bundle the leads as shown in the picture. 70223 70228 Torx T10 Insert wire 70223 and 2 x push-button-wire 70228. Assemble push-button-wire 70228 connected to socket 1 underneath the unused screw-terminals as shown in the picture 70228 Tighten E225_RFID_Mono with 2 x 10876 from the outside FBL041007 Formblatt gtig ab: 29.04.2016 Erstellt / gendert: J. Binder Beschreibung der letzten Formblattnderung: Anpassung an VA3S.010-01 V00 Nur fr internen Gebrauch! Gltig ist nur die Version auf dem File-Server oder berwachte Kopien Vertraulich Vervielfltigung u. Verwertung, sowie Weitergabe an Dritte ohne schriftl. Zustimmung von BOWA ist nicht gestattet!
Installation manual Assembly of RFID-Reader 70615 / 70616 Dok.-Reg-Nr.:
PR709_2 Page 2 of 3 70228 70223 Torx T10 2.2.2. Insert E225_RFID_Bipo 70615 into socket-
slots and bundle the leads as shown in the picture. Insert wire 70223 and 2 x push-button-wire 70228. Assemble push-button-wire 70228 connected to socket 1 underneath the unused screw-terminals as shown in the picture Tighten E225_RFID_Bipo with 2 x 10876 from the outside 2.2.3. Add Label FCC-IDs above Type-Label at the backside of the host device. 2.2.4. Label FCC-ID FCC (USA) 15.21 Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.105(a) Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. ISED (Kanada) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil FBL041007 Formblatt gtig ab: 29.04.2016 Nur fr internen Gebrauch! Gltig ist nur die Version auf dem File-Server oder berwachte Kopien Installation manual Assembly of RFID-Reader 70615 / 70616 Dok.-Reg-Nr.:
PR709_2 Page 3 of 3 doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en 3. SYMBOLS USED Legend:
Information Check 4. DOCUMENT HISTORY Version date Change description 10.10.2017 Inital version 09.07.2018 2.2.3 FCC-ID Label on backside was added 1 2 5. DISTRIBUTION Division Local position TEE Only online available Team-leader date/signature n.a. for online FBL041007 Formblatt gtig ab: 29.04.2016 Nur fr internen Gebrauch! Gltig ist nur die Version auf dem File-Server oder berwachte Kopien