FCC ID: 2ATZX-FWBT200 Freewheel 200s E -scooter

 

NOTE: CAN BE USED AS A KICK SCOOTER OR, BY PRESSING THE THUMB

THROTTLE, ELECTRIC POWER WILL ENGAGE THE MOTOR FOR ADDED

POWER AND ACCELERATION. YOUR RIDE TIME WILL VARY GREATLY

DEPENDING ON THE AMOUNT OF POWER-ASSISTED RIDING PERFORMED.

ELECTRIC SCOOTER

OWNER’S MANUAL

FOR USE WITH THE FOLLOWING PULSE PERFORMANCE PRODUCTS™ SCOOTERS

•

FREEWHEEL 200s (with integrated Bluetooth™ Speaker)

DO NOT RETURN TO STORE! QUESTIONS OR COMMENTS?

CALL (866)-434-6067

07.30.19

Table of Contents

Safety and Warnings

Before You Start

Assembly

FCC Information - Battery Charger

Hardware Maintenance

Before You Ride

Speaker Pairing and Use

Repair and Maintenance

Troubleshooting

Scooter Components

Warranty

FCC Information - Bluetooth™ Speaker

2-3

4

5-6

6

7

7

8

8-10

11

12

13

13

Safety and Warnings

WARNING:

Riding an electric scooter can be a dangerous activity. Certain conditions may cause components to fail without fault

of the manufacturer. Scooter can and is intended to move and it is therefore possible to lose control, fall off and/or get into dangerous situations

that no amount of care, instruction or expertise can eliminate. If such a thing does occur you can become seriously injured or die, even when

using safety equipment and other safety precautions. RIDE AT YOUR OWN RISK AND ALWAYS USE COMMON SENSE. To reduce the risk of

injury, ADULT SUPERVISION IS REQUIRED.

This manual contains many warnings and cautions concerning the consequences of failing to inspect, maintain or properly use your electric

scooter. Since any incident can result in serious injury or even death, we do not repeat the warning of possible serious injury or death each

time such a possibility is mentioned in this manual.

APPROPRIATE RIDING ATTIRE

Always wear proper protective equipment such as:

• Approved safety helmet. (Helmet may be legally required by local law or regulation in your area.)

• Elbow pads and knees pads

• Long sleeved shirt, long pants

• Gloves

• Lace up, closed toe shoes with rubber soles, never ride barefooted or in sandals, and ensure that shoelaces are tied and kept out of the way

of the wheels and drive system.

RIDER USE AND PARENTAL SUPERVISION

RIDER MUST NOT EXCEED THE WEIGHT LIMIT OF 120 pounds (54kgs). Rider weight does not always mean a person’s size is appropriate

To reduce the risk of injury, ADULT SUPERVISION IS REQUIRED.

This manual contains extremely important safety information. It is your responsibility to completely review this information and make sure that

all riders understand all warnings, cautions, instructions and safety topics and assure that all riders are able to safely and responsibly use this

scooter. Pulse Performance Products™ advises that you periodically review and reinforce all information in this manual with all riders, and

that you inspect and maintain your scooter to insure their safety.

to 12 yrs.

decision to allow their child to use the scooter should be based on the child’s maturity, skill level and their ability to follow rules.

Never use in roadways, near motor vehicles, on or near steep inclines or steps, swimming pools or other bodies of water.

Do not touch the motor or brakes on the scooter when in use or directly

after use as these parts can become extremely hot.

Keep this scooter away from small children and remember that it is intended for use only by persons who are, at a minimum, completely

competent and comfortable while operating this product.

AND CONDITIONS

RIDING PRACTICES

Check and obey any local laws or regulations which may affect the locations where the electric scooter may be used.

Always ride defensively. Watch out for obstacles that could catch your wheel or force you to turn suddenly or lose control. Be careful to avoid

pedestrians, other wheeled products (such as skaters, skateboards, scooters, bikes, etc.), children or animals who may enter your path.

Always respect the rights and property of others.

Do not depress the thumb button on the hand grip unless you are on the scooter and in a safe, outdoor environment that is suitable for riding.

.

Do not attempt or perform racing, stunt riding, tricks, or other manuevers, which may cause loss of conrtrol, or may cause uncontrolled operator

actions or reactions. This product is not made to withstand abuse from jumping, curb grinding or other dangerous riding activities.

2

Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call (866) 434-6067.

Safety and Warnings

WARNING:

FAILURE TO HEED TO THE WARNINGS LISTED BELOW INCREASES RISK OF POTENTIAL SERIOUS INJURY. USE THE

APPROPRIATE CAUTION WHEN RIDING AND ALWAYS WEAR PROTECTIVE GEAR.

Maintain a hold with both hands on the handlebars at all times.

Never allow more than one person at a time to ride the scooter.

Never use on roadways, near motor vehicles, on or near steep inclines or steps, swimming pools or other bodies of water.

Avoid sharp bumps, drainage grates, and sudden surface changes.

Do not allow your hands, feet, hair, body parts, clothing or similar articles to come in contact with moving parts, wheels, or drivetrain, while the

motor is running.

Never ride while using a cell phone or wearing headphones.

Never hitch on to or with another vehicle or pull anyone or anything.

Never immerse the scooter in water; electrical and drive components could be damaged by water or create other possible unsafe conditions.

ater, mud, ice,

bumpy, uneven, slick, or rough surfaces could impair traction and contribute to possible loss of control. Avoid excessive speeds that can occur

from downhill rides which could cause loss of control.

Owners are encouraged to highlight (for conspicuity)

Do not ride at night or in areas of limited visibility.

using lighting, reflectors, and for low-riding units, signal flags on flexible poles

originally supplied by the manufacturer are in proper place and in serviceable condition. That any and all axle guards, chain guards, or other

covers or guards supplied by the manufacturer are in place and in serviceable condition.

Ensure that the area that the unit is to be operated in is safe and suitable for safe operating.

Ensure that all safety labels are in place and understood by the operator.

Persons with the following conditions shall be cautioned not to operate: Those with heart conditions, pregnant women, persons with head,

back, or neck ailments, or prior surgeries to those areas of the body. Persons with any mental or physical conditions that may make them

susceptible to injury or impair their physical dexterity or mental capabilities to recognize, understand, and perform all of the safety instructions

and to be able to assume the hazards inherent in unit use.

Maximum operating speed is 8 MPH (13 KM/H).

Before each ride the following checks will need to be performed to the scooter:

• Ensure that the brake system is functioning properly.

• Components shall be maintained and repaired in accordance with the manufacturers authorized replacement parts with installation

performed by dealers or other skilled individuals.

BATTERIES, FUSES, CIRCUIT BREAKERS & USING THE BATTERY CHARGER

The battery charger should be regularly examined for damage to the cord, plug, enclosure and other parts. In the event of such damage, if

any is found, the scooter should not be charged until the battery charger has been repaired or replaced.

Use only with the supplied, recommended battery charger.

Always use caution when charging.

The battery charger is not a toy and should be operated by an adult.

Disconnect the battery charger and unplug from scooter when not in use.

Do not exceed recommended charging time.

Always disconnect the battery charger from the scooter prior to wiping down and cleaning with any liquid.

Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.

Only use the batteries specified by the manufacturer.

RISK OF FIRE. Do not bypass fuse or circuit breaker. The circuit breaker on this scooter is not replaceable by the user - it is an integral part of

the controller. Replace the controller only with an identical part as specified by the manufacturer.

WARNING:

FAILURE TO HEED TO THE WARNINGS LISTED ABOVE INCREASES RISK OF POTENTIAL SERIOUS INJURY. USE THE

APPROPRIATE CAUTION WHEN RIDING AND ALWAYS WEAR PROTECTIVE GEAR.

Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call (866) 434-6067.

3

Before You Start

WARNING:

Remove all packing and items from the display box. Make sure that the power switch is

turned “OFF” before assembling the scooter.

Estimated Assembly Time

• Allow up to 25 minutes for assembly, not including initial charge time.

• Allow up to 12 hours for the initial charge (see page 6 for charging information).

NOTE: This scooter does not have a

manual reset button or fuse. It is

integrated into the controller and is

self-resetting.

battery charger

(included)

Required Tools

10 mm / 8 mm

wrench

(included)

two [2] 13 mm

wrenches

(not included)

5 mm hex wrench with

philip screw driver ( included)

second

5 mm hex wrench

(not included)

3 mm hex wrench

(not included)

WARNING: DO NOT USE NON-PULSE PERFORMANCE PRODUCTS™ PRODUCTS WITH YOUR

may or may not be compatible with the design and will void the warranty.

Altering of the original components

4

Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call (866) 434-6067.

Assembly

Handlebar Steer Tube Assembly

Tools required: 5 mm hex wrench, 10 mm wrench

Locator Hole

The push button

1. Depress the push button located on the

rear of the fork tube and insert the handlebar

steer tube onto the fork tube.

should align with the locator hole in the

handlebar steer tube and lock the steer tube

securely in place. Once the push button pops

out of the locator hole, lift up on the steer tube

to ensure it cannot slide off. If it cannot, then

proceed to step 2.

2. Tighten the bolts with the 5 mm hex

wrench and 10 mm wrench. Tighten bolts

evenly and securely.

3. Align handlebars (a) onto the stem tube

cradle (b) and install handlebar clamp (c)

ensuring that the clamp locating pin inserts

into the Anti-Rotation Hole (hole should be

facing upward). Install hardware and tighten

both bolts and nutswith the 5mm hex wrench

and 10mm wrench evenly and securely

a

c

b

Anti-Rotation

Hole

4. Locate the 3 small, black clips that are

pre-installed on the trottle cable - they look like this >>>

They slide easily along the cable, and are designed to

be inserted into 1 hole on the scooter neck and 2 holes

on the steering column, to keep the throttle cable located

in a clean, safe position. Simply align each clip with its

respective hole (as shown) and press it firmly into place.

Do not remove clips from the cable before inserting.

Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call (866) 434-6067.

5

Assembly

Charging the Battery

WARNING:

Battery must be fully charged before you ride your electric scooter

.

Required components: battery charger

• Initial battery charge time - 12 hours

• Recharges after initial charge - up to 10 hours

• When scooter is not in regular use batteries need to be charged on a monthly basis to maximize performance

1. Make sure power switch is in the OFF

position before plugging in the charger. Insert

charger into charging port on the left side of

the battery box.

2. Plug the battery charger into a wall power

outlet. The light on the charger housing

should illuminate. Red LED light indicates

battery is charging and a green LED light

indicates battery is fully charged.

WARNING:

compliance could void the user’s authority to operate the equipment.

FCC instruction for Battery charger:

the party responsible for compliance could void the user’s authority

to operate the equipment.

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna. --Increase the

separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

WARNING:

instructions may damage your product and void your warranty.

Note: Do not store the battery in temperatures above 70˚F (21˚C) or below 32˚F (0˚C).

Note: The charger has a small window with one LED light that indicates the charge status. Refer to the illustration on the charger unit for

the actual “charging” and “charged” status indication. Your charger may get warm during use; this is normal and is no cause for concern.

Note: Batteries must be recharged at least once a month even when the scooter is not in use. Failure to do so may result in batteries that

will no longer accept a charge.

6

Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call (866) 434-6067.

Hardware Maintenance

Brake

Check the brakes for proper function. When you step on the brake it should provide positive braking action. When you apply the brake with

the speed control on, the brake cut off switch should stop the motor.

Frame, Fork, Handlebars & Hardware

Check for cracks or broken connections. Although broken frames are rare, it is possible for aggressive rider to accidentally run into a curb or wall

and bend or break a frame. Make sure that all fasteners are properly tightened or adjusted. Get in the habit of inspecting your scooter

on a regular basis.

Tires, Wheels & Hubs

Periodically inspect the wheels for excess wear.

Safety Gear

Always wear proper protective gear such as an approved safety helmet. Elbow pads and knee pads are recommended. Always wear athletic

shoes (lace up shoes with rubber soles), never ride barefooted or in sandals, and keep shoelaces tied and out of the way of the wheels,

motor and drive system.

Batteries

Make sure the power switch is turned off whenever the scooter is not in use. Never store the product in freezing or below freezing

temperatures! Freezing will permanently damage the batteries.

Before You Ride

Before you ride always check and for the following:

Safety Gear

Always wear proper protective gear such as:

• Approved safety helmet. (Helmet may be legally required by local law or regulation in your area.)

• Elbow pads and knees pads

• Long sleeved shirt, long pants

• Gloves

• Lace up shoes with rubber soles.

Brake

Check the brakes for proper function. When brake is applied it should slow/stop the rear wheel without excessive effort. When you apply the

brake with the throttle on, the brake cut off switch should stop the motor. Make sure that the brakes are not rubbing when the brake is not

being applied. Do not ride the scooter if the brakes are not functioning properly. Do not touch the brake on the scooter when in use or directly

after use as these parts can become extremely hot.

Throttle

Make sure before throttle is ever depressed, that you are in an open and safe area to ride, you are balanced on the scooter and have both

hands on the handlebar controls. Push starting the scooter will greatly increase your ride time. We recommend using as a “PUSH” or “KICK”

type scooter, and using the power button only when added power and acceleration are needed - doing so will also greatly increase your ride

time.

Tires, Wheels & Hubs

Inspect the wheels for excess wear and replace if necessary.

Frame, Fork and Components

Always carefully inspect your scooter before you ride. Check for cracks, broken worn or loose components which should be repaired or

replaced before you ride.

Make sure that all fasteners are properly tightened or adjusted. Get in the habit of inspecting your scooter on a regular basis.

Battery

Always make sure the power switch is in the “off” position whenever the scooter is not in use. Never store the product in freezing or below

freezing temperatures. These low temperatures will permanently damage the battery.

WARNING:

Always ensure that you are in a safe open area to ride before you

engage the throttle. Never depress the throttle button without being on the scooter in a

balanced, ready to ride position with both hands on the handlebar controls.

Failure to follow these instructions may damage your scooter and void your warranty.

Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call (866) 434-6067.

7

Bluetooth™ Speaker Pairing and Use - See WARNING BELOW

Pairing Speaker to Audio Device

WARNING:

NEVER ATTEMPT TO USE THE CONTROLS ON YOUR PAIRED DEVICE WHILE THE

SCOOTER IS IN MOTION. ALWAYS COME TO A COMPLETE STOP IN A SAFE LOCATION BEFORE

ADJUSTING VOLUME, CHANGING SONGS OR PERFORMING ANY FUNCTION ON YOUR DEVICE,

REGARDLESS IF IT IS PAIRED TO THE SCOOTER’S SPEAKER OR NOT. THIS IS FOR YOUR OWN SAFETY

AND THE SAFETY OF THOSE AROUND YOU. FAILURE TO FOLLOW THIS WARNING COULD LEAD TO

LOSS OF CONTROL OF THE SCOOTER RESULTING IN SERIOUS INJURY OR DEATH.

Before you can use your scooter’s Bluetooth™ speaker, you must pair it with your phone or other audio device by following these simple steps:

Step 1. Make sure your phone or audio device is on, and the Bluetooth™ function is enabled.

Step 2. Turn on your Freewheel 200s Scooter, and listen for the 8 tones, followed by the words “Bluetooth Mode”.

Step 3. Your device should give you an option to PAIR with Bluetooth™ device FWBT200.

Step 4. Allow your device to PAIR. If successful, you will hear 2 confirmation tones that the device is now paired to your scooter’s speaker.

Step 5. Use the controls on your device to listen to your favorite music as you cruise!

NOTE: After successfully pairing, your device will stay paired until you unpair it from the scooter’s speaker. This allows you to simply

turn the scooter on and off, without the need to follow the steps above again. And remember, if your device is already paired with

another Bluetooth™ product, it will not connect/pair with your scooter’s speaker until that product is turned off or unpaired.

Pairing Help

• Call (866) 434-6067 to speak with a customer service representative

Repair and Maintenance

Only use the supplied battery charger. If battery charger is damaged discontinue use immediately and replace with a Pulse Performance

Products™ recommended battery charger.

Wheels and drive system components are subject to normal wear and tear. It is the responsibility of the user to regularly inspect wheels for

excess wear and adjust and replace drive train components as required.

Battery Charger

Wheels

Replacement Parts

Repair Help

Most of the common replacement parts are available for purchase by calling (866) 434-6067.

• Call (866) 434-6067 to speak with a customer service representative

WARNING:

The brake is capable of locking up and skidding the rear wheel if not applied correctly.

Always try and avoid skidding as this could cause you to lose control of the scooter and will cause damage to the

rear tire. Practice using the brake in an unobstructed open area to become familiar with its function and until you

can make smooth, controlled stops.

8

Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call (866) 434-6067.

Repair and Maintenance

Rear Wheel-Transmission-Motor Assembly Replacement

Tools required: two [2] 13 mm

wrenches, phillips screwdriver

1. Using a #2 phillips screwdriver, remove the 5 deck

screws and lift the deck away by shifting it up and

towards the rear of the scooter, allowing the deck

to slip off of the brake pedal. The brake pedal will not

come off with the deck.

2. Using a #2 phillips screwdriver, remove the 2 side-transmission

mounting screws from the frame.

Using two [2] 13 mm wrenches loosen the

rear wheel axle nut and bolt. CAREFULLY remove

the wheel AND transmission from the frame, with the

wheel and motor remaining on the transmission.

3. Note the location of all rear wheel assembly hardware and ensure to properly re-install all items, including

the deck and deck scrrews, tightly and securely.

10

Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call (866) 434-6067.

Repair and Maintenance

Front Wheel Replacement

Tools required: Two 5mm hex wrenches

1. Using two 5 mm hex wrenches loosen

and remove the front axle by turning the

wrenches counter clockwise.

2. Reinstall new replacement wheel

ensuring to note the order and location of all

components.

3. Reinstall hardware and tighten clockwise

with a 5 mm hex wrench.

Battery Care and Disposal

Do not store the battery in temperatures above 70°F (21°C) or below 32°F (0°C).

THIS SCOOTER CONTAINS SEALED LEAD ACID BATTERIES WHICH MUST BE RECYCLED IN AC-

CORDANCE TO YOUR LOCAL AND STATE LAWS. PLEASE CAREFULLY READ AND UNDERSTAND THE

FOLLOWING DISPOSAL INSTRUCTIONS:

Disposal: This product contains sealed lead acid batteries which must be disposed or recycled in an environmentally safe manner. Do not

exhausted batteries to a state or federal approved lead acid battery recycler or check with your local retailer of vehicle batteries.

WARNING:

Make sure to wash your hands after handling batteries as they contain lead compounds.

WARNING:

(nickel-cadmium) batteries.

Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable

Do not store the battery in temperatures above 70°F (21°C) or below 32°F (0°C).

Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call (866) 434-6067.

9

Troubleshooting

Problem

Possible Cause

Solution

Scooter will not run.

Battery is not charged.

Fully charge the battery. First charge should be 12 hours and up to

10 hours for recharges.

Wires or connectors are

loose or unplugged.

Check to ensure that charger is tightly plugged into both the wall

and the scooter.

Scooter run time is short.

Battery requires charging.

Battery will not accept full

charge.

Fully charge the battery. First charge should be 12 hours and up to

10 hours for recharges.

Check to ensure that battery charger is tightly plugged into both the

wall and the scooter.

Battery may need to be replaced. Even with proper care,

rechargeable batteries do not last forever. The average

rechargeable battery life is 1 to 2 years depending on scooter

conditions and use. Replace only with Pulse Performance

Products™ replacement batteries.

Rider weight exceeds limit or

terrain is too steep or rough

Limit use to riders under the maximum weight limit and ride only on

solid, flat and dry surfaces such as pavement or level ground.

Scooter suddenly stops working.

Circuit breaker has tripped.

The self-resetting circuit breaker (located inside the controller - not

a user serviceable part) will automatically trip and turn off the power

if the motor is overloaded. Allow up to a full minute for it to reset.

An excessive overload (steep incline or excessive rider weight) could

have caused the motor to overheat and trip the breaker. Avoid

repeatedly tripping the breaker, as this can damage the controller.

Check all wires and connectors to make sure they are connected

and tight.

Scooter runs sluggishly.

Scooter is overloaded.

Make sure you do not overload the scooter by exceeding the 120

lb (54 kg) maximum weight limit, going up steep inclines, or towing

objects behind the scooter. Avoid overloading the scooter as this will

prematurely wear out the batteries, motor and componentry.

Unsuitable riding

conditions.

level ground.

Speaker will not connect or play music

Not properly paired to device

Make sure that you have followed the pairing instructions on page 8

Not connected to audio device Make sure that your device is not already connected to another speaker.

Scooter not turned on or

battery charge level too low

Make sure that your scooter is fully charged

Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call (866) 434-6067.

11

Scooter Components

15

14

13

26

5

4

25

1

24

4

20

3

10

16

19

18

14

15

8

27

17

6

2

7

23

PART DESCRIPTION

1. Frame

2. Motor

3. Front Fork & Rotation

Limit Screw

4. Headset (Upper & Lower)

5. Clamp

6. Kickstand

7. Battery Box

8. Deck

9. Rear Wheel

10. Front Wheel

11. Spring Plate

12. Foot Brake

13. Thumb Throttle

14. Grip

15. Grip End Plug

16. Controller

17. Batteries

18. Handlebar & Clamp

19. Charger Port & Dust Cover

12

11

21

22

9

22. Transmission

23. Motor Cover

24. Steering Limit Cover

25. Spring Button

26. Steering tube

27. Bluetooth speaker

12

Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call (866) 434-6067.

Warranty

Limited Warranty

This Limited Warranty will be void if the product is ever

• used in a manner other than for recreation or transportation

• used as a rental

The manufacturer warranties this product to be free of manufacturing defects for a period of 90 days from the date of purchase. This Limited

Warranty does not cover normal wear and tear, tires, cables, or any damage, failure or loss caused by improper assembly, maintenance,

.

storage or use of this Pulse Performance Products™ electric scooter.This warranty is limited to the replacement of defective parts only.

The manufacturer is not liable for incidental or consequential loss or damage due directly or indirectly to the use of this product.

Pulse Performance Products™ does not offer an extended warranty. If you have purchased an extended warranty, it must be honored by the

store at which the scooter was purchased from.

For your records, keep your original sales receipt with this manual.

SB 1918 (CALIFORNIA) DECLARATION

YOUR INSURANCE POLICIES MAY NOT PROVIDE ANY COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER. TO

DETERMINE IF ANY COVERAGE IS PROVIDE CONTACT YOUR INSURANCE COMPANY OR INSURANCE AGENT.

FCC Information

- Bluetooth™ Speaker System

FCC Warning Information

- Bluetooth™ Speaker System

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the

equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter.

Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call (866) 434-6067.

13

facebook.com/pulseperfprod

twitter.com/pulseperfprod

Pulse Performance Products™

A Division of Bravo Sports™

12801 Carmenita Rd.

Santa Fe Springs, CA 90670

© 2019 - 2020 Pulse Performance Products™ -

All Rights Reserved



 

 

 

 

 

 

 

 

 

 

label Size: 30mm*20mm Model NO.: Freewheel 200s FCC ID:2ATZX-FWBT200 Zhejiang Easy Vehicle Co., Ltd Made in China

 

 

Bravo Sports

Federal Communications Commission

Authorization and Evaluation Division

1435 Oakland Mills Road

Columbia, MD 21046

Date: 2021-09-03

SUBJECT: FCC Application for (FCC ID:2ATZX-FWBT200)

To Whom It May Concern:

We, the undersigned, hereby authorize Yoyo Zhou in Shenzhen Huaxia Testing

Technology Co., Ltd at 1F., Block A of Tongsheng Technology Building, Huahui Road,

Dalang Street, Longhua District, Shenzhen, China on our behalf, to apply to the Federal

Communications Commission on our equipment. Any and all acts carried out by

Shenzhen Huaxia Testing Technology Co., Ltd on our behalf shall have the same

effect as acts of our own.

This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We,

the applicant, are not subject to a denial of federal benefits pursuant to Section

5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is

subject to a denial of federal benefits pursuant to that section.

(Must be signed by the person that is listed on the FCC Website)

Sincerely,

Signature: Jack Lovley

Contact name: Jack Lovley

Company name: Bravo Sports

Address: 12801 Carmenita Road, Santa Fe Springs, CA 90670-4805 USA

Date: 04/17/2018

VCB_F-01: Operating Procedures Form – FCC Authorization v02

Page 1 of 1



 

 

Bravo Sports

Federal Communications Commission

Authorization and Evaluation Division

Confidentiality Request regarding application for certification of FCC ID: 2ATZX-

FWBT200

Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request

confidential treatment of information accompanying this application as outlined below:

Exhibit Type

1. Block Diagram,

2. Schematics,

3. Operational Description

File Name

1. 2ATZX-FWBT200 -Block diagram

2. 2ATZX-FWBT200 -SCH

3. 2ATZX-FWBT200-Operational description

The above materials contain trade secrets and proprietary information not customarily

released to the public. The public disclosure of these materials may be harmful to the

applicant and provide unjustified benefits to its competitors.

The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this

application and all accompanying documentation will not be made before the date of the

Grant for this application.

Pursuant to DA04-1705 June 15, 2004 of the Commission’s public notice, we also

request temporary confidential treatment of information accompanying this application

as outlined below for an initial period of xxxx (ie- “45”, “90” or “180”) days:

Exhibit Type

N/A

File Name

N/A

Signature: Jack Lovley

Contact name: Jack Lovley

Company name: Bravo Sports

Address: 12801 Carmenita Road, Santa Fe Springs, CA 90670-4805 USA

Date: 04/17/2018

VCB_F-01: Operating Procedures Form – FCC Confidentiality v02

Page 1 of 1