FCC ID: SK4BCS-MV65 WALKIE TALKIE

ridge BCS-MV6S with flashlight 5 work channels 7 weather channels Helping You Communicate Using Radio BiidgeCoqy) Model BCS-MV6S with flashlight 5 work channels 7 weather channels Helping You Communicate Using Radio Welcome Thank you for purchasing the BridgeCom BCS-MV65. MURS two-way radio. The goal of BridgeCom is to provide a cost-

effective, feature rich, easy to use radio. This owner's manual will acquaint you with the features and operation of the radio. Every effort has been made in the preparation of this manual to properly operate the radio before use. Multi-Use Radio Service (MURS) uses channels in the 151 - 164 MHz spectrum range. An individual license is not required to operate a MURS transmitter. The most common use of MURS channels Is for short-distance, two-

way communications using small, portable hand-hekd radios that funo-

tion similar to walkie-talkies. Your radio has & MURS frequencies and 7 NOAA weather channels. CH 1 = 151.820 MHz (11.25 kez) CH 2 = 151.880 MHz (11.25 kez) CH 3 = 151.040 MHz (11.25 kez) CH 4 = 154.570 MHz (20.00 kHz) CH 6 = 154.600 MHz (20.00 kHz) NOAA Weather Channels WX1 162.550 MHz WX2 162.400 MHz WX3 162.475 MHz WXA 162.425 MHz WXE 162.450 MHz WX6 162.500 MHz WX? 182. 528 Mil Welcome Thank you for purchasing the BridgeCom BCS-MV65. MURS two-way radio. The goal of BridgeCom is to provide a cost-

effective, feature rich, easy to use radio. This owners manual will acquaint you with the features and operation of the radio. Every effort has been made in the preparation of this manual to properly operate the radio before use. Multi-Use Radio Service (MURS) uses channels in the 151 154 MHz spectrum range. An individual license is not required to operate a MURS transmitter. The most common use of MURS channels is for short-distance, two-

way communications using small, portable hand-held radios that func-

tion similar to walkie-talkies. Your radio has 5 MURS frequencies and 7 NOAA weather channels. MURS Work Channels CH 1 = 151.820 MHz (11.25 kHz) CH 2 = 151.880 MHz (11.25 kHz) CH 3 = 151.940 MHz (11.25 kHz) CH 4 = 154.570 MHz (20.00 kHz) CH 5 = 154.600 MHz (20.00 kHz) NOAA Weather Channels WX1 162.550 MHz WX2 162.400 MHz WX3 162.475 MHz WX4 162.425 MHz WX5 162.450 MHz WX6 162.500 MHz WX7 162.525 MHz CONTENTS USER SAFETY INFORMATION.. SAFETY WARNING...... UNPACKING........ Supplied Accessories PREPARATION .. Charging instructions. Charging step.... Installation / Removal of lithium battery... Antenna Installation / Removal.... Installation / Removal of belt clip..... Installing external speakers / Microphone headphones. ....... GETTING FAMILIAR WITH RADIO Function key explanation... LCD display Main function Side key functions............ OPERATION... Power ON / Adjust volume . Channel Select Transmit / Receive. MENU SETTING Menu usage... Menu List.......... CTCSS/DCS..... WARRANTY AND SERVICE User Safety Information As a user of this radio be fully aware of hazards to RF exposure. The Federal Communications Commission (FCC), with its action in General Docket 98-62, November 7, 1997, has adopted a safety stan-

dard for human exposure to Radio Frequency (RF) electromagnetic energy emitted by FCC regulated equipment. Proper operation of this DO NOT transmit for more than a 50% duty cycle (example: 1 min. transmitting, 1 min. recelving or in standby) transmitting more than 50% of the time may cause FOC RF exposure compliance require-

ments to be exceeded. The radio Is transmitting when the red LED Is Illuminated, hoki the radio approximately 1 inch (2.5 om) away from the MIC located on the front of the radio. The above operating conditions are required for meeting FCC RF ex-

posure compliance, failure to follow these restrictions are consklered a Mm) Safety Warning Do not transmit the radio with a damaged antenna or touch the anten-

a while transmitting. Strong electromagnetic waves are emitted from the raclio which may damage the radio or cause an RF burn to your Do not use non-approved accessories with your radio. Unauthorized accessories may create unauthorized RF emissions or cause damage to the radio or may result In illegal operation. Do not disassemble or modify the radio, doing so will void the warranty and may result in illegal operation. Do not leave the radio In direct sunlight or around excessive heal, do-

Ing 80 may cause the battery to explode or catch fire. Do not use radio If it has been immersed in water an electronic shook May occur or permanent damage may occur to the radio. NOTE: /t is important for users to understand and recognize the general risks of using two-way radios. As a user of this radio be fully aware of hazards to RF exposure. The Federal Communications Commission (FCC), with its action in General Docket 93-62, November 7, 1997, has adopted a safety stan-

dard for human exposure to Radio Frequency (RF) electromagnetic energy emitted by FCC regulated equipment. Proper operation of this radio will result in user exposure far below the Occupational Safety and Health act (OSHA) and FCC limits. DO NOT transmit for more than a 50% duty cycle (example: 1 min. transmitting, 1 min. receiving or in standby) transmitting more than 50% of the time may cause FCC RF exposure compliance require-

ments to be exceeded. The radio is transmitting when the red LED is illuminated, hold the radio approximately 1 inch (2.5 cm) away from the MIC located on the front of the radio. The above operating conditions are required for meeting FCC RF ex-

posure compliance, failure to follow these restrictions are considered a violation. 11]

Do not transmit the radio with a damaged antenna or touch the anten-

na while transmitting. Strong electromagnetic waves are emitted from the radio which may damage the radio or cause an RF burn to your skin. Do not use non-approved accessories with your radio. Unauthorized accessories may create unauthorized RF emissions or cause damage to the radio or may result in illegal operation. Do not disassemble or modify the radio, doing so will void the warranty and may result in illegal operation. Do not leave the radio in direct sunlight or around excessive heat, do-

ing so may cause the battery to explode or catch fire. Do not use radio if it has been immersed in water an electronic shock may occur or permanent damage may occur to the radio.

|2) Unpacking Please take care to remove the radio from the box. We recommend that you confirm the following Items in the box before discarding the Preparation 1 Charging instructions

* The battery pack is not charged at the factory, charge before use. After purchase or after long-term storage (more than two months), charging the battery pack for the first time does not allow the bat-

tery pack to reach its saturated usage capacity. After repeated charging and discharging two or three times, normal charging and battery capacity can be achieved.

* Tum off the power of the radio before charging. A radio that Is left powered on in the charger cup may prevent the battery from charging properly. Once the battery falls to maintain its charge during normal use the battery pack may have reached the end of Its life. Replacement with a new battery will be necessary. NOTE:

Do not recharge the battery pack once it is fully charged. Doing so may cause the life of the battery pack to shorten or the battery pack may be damaged.

+ After Recharging the battery pack, remove from the charger cup.

+ Do not short the battery terminals or discard batteries in a fire or normal trash waste. i Charging step Attach the A/C wall adapter to the charger oup by inserting the barrel connector into the socket looted on back of the charger oup. Plug the AJC wall adapter In a 110V wall outlet the charger will show a green light, Insert the battery pack or the radio with the battery paok into the char-

ger card slot. The red light of the charger flashes to start charging; after the full charge, the green light is on and charging is complete. 14!

Please take care to remove the radio from the box. We recommend that you confirm the following items in the box before discarding the packaging materials. H@ Supplied Accessories Radio Antenna 8.4V Li-ion battery Charger cup Wall Adaptor Belt Clip Manual Wrist Strap 13]

H Charging instructions

+ The battery pack is not charged at the factory, charge before use. After purchase or after long-term storage (more than two months), charging the battery pack for the first time does not allow the bat-

tery pack to reach its saturated usage capacity. After repeated charging and discharging two or three times, normal charging and battery capacity can be achieved.

+ Turn off the power of the radio before charging. A radio that is left powered on in the charger cup may prevent the battery from charging properly.

+ Once the battery fails to maintain its charge during normal use the battery pack may have reached the end of its life. Replacement with a new battery will be necessary.

@ Charging step Attach the A/C wall adapter to the charger cup by inserting the barrel connector into the socket located on back of the charger cup. Plug the A/C wall adapter in a 110V wall outlet the charger will show a green light. Insert the battery pack or the radio with the battery pack into the char-

ger card slot. The red light of the charger flashes to start charging; after the full charge, the green light is on and charging is complete.

|4]

Installation / Removal of lithium battery Ensure the radio is powered off before attaching or removing the battery by using the control knob on top of the radio. Rotate the knob counter clockwise until you hear a olick and the knob no longer ro-

zie sf ii i

A gE z

3 3 i fi i

fi fe u G ri E 5 ga

$34 zg ey ede g le an i

pt opens located just below the release tab (Do not pull the release tab past Its stopping point). Hold the belt olip up per previous in-

struction, slightly lift and pull the battery out and way from the radio.

@ Antenna Installation / Removal Ensure the radio Is powered off per previous instruction.

> Installation Align the antenna onto the treaded location on top of the radio by holding at the base of the antenna. Screw the antenna Into place by rotating In @ clockwise direction being careiul not cross thread the antenna until firmly seated (Do not overtighten the antenna).

> Removal Remove the antenna by holding the antenna at the base and un-

screw the antenna counterclockwise until completely out of the threaded connector. NOTE: Do not t ntenna as a handle, Hang a key- chain or external speaker microphone on the antenna. This will dam-

age the antenna and reduce the performance of the radio. I installation / Removal of belt clip The belt clip should be pre-installed at the factory. To remove the belt clip, use a small Philips head screw driver to remove the two screws hokling the clip to the frame, To install the belt press and hoki the belt function and adjust the volume control to a comfortable listening level prior to Inserting an ear accessory. Press and release side key (1) again to close the squelch.

@ Installation / Removal of lithium battery Ensure the radio is powered off before attaching or removing the battery by using the control knob on top of the radio. Rotate the knob counter clockwise until you hear a click and the knob no longer ro-

tates. Installation Using your thumb press and hold the belt clip into its open position. Align the battery pack tabs with the corresponding position on the aluminum frame by holding the battery slightly up and pushing the battery forward and into the two frame slots by using the other end of the battery pushing downward and into the frame. Ensure the battery is properly seated prior to pushing the main battery latch into place (Do not force the battery or latch into position). You should hear a firm click once the battery is latched and properly installed. Turn on the radio using the control knob on top of the radio by ro-

tating clockwise. A click will be heard to indicate power has been applied, once the radio has completed its power on sequence it is ready to use. Removal To remove the battery, turn off the radio using the control knob on top of the radio per previous installation step. Lift up on the release tab indicated by OPEN until the main latch opens located just below the release tab (Do not pull the release tab past its stopping point). Hold the belt clip up per previous in-

struction, slightly lift and pull the battery out and way from the radio.

@ Antenna Installation / Removal Ensure the radio is powered off per previous instruction. Installation Align the antenna onto the treaded location on top of the radio by holding at the base of the antenna. Screw the antenna into place 15]

by rotating in a clockwise direction being careful not cross thread the antenna until firmly seated (Do not overtighten the antenna). Removal Remove the antenna by holding the antenna at the base and un-

screw the antenna counterclockwise until completely out of the threaded connector. Hf Installation / Removal of belt clip The belt clip should be pre-installed at the factory. To remove the belt clip, use a small Phillips head screw driver to remove the two screws holding the clip to the frame. To install the belt press and hold the belt clip in place and align the screws into the frame holes being careful not to cross thread the screws (Do not over tighten the screws or risk stripping the screw holes). i Installing external speakers / Microphone headphones Remove the accessory dust cover using a coin or slotted screwdriver

(keep the cover in a safe place for use when an attached accessory is not being used). Insert the accessory into appropriate jack, press and release top side key (1) to open the radio squelch/monitor function and adjust the volume control to a comfortable listening level prior to inserting an ear accessory. Press and release side key (1) again to close the squelch. 16]

Getting Familiar with Radio [EXIT] Key oor * Short press: exits the menu mode;

*' Lang prose: Locktuniock sll butions and ays wih exception of

@ LCD display On the display are various Indicators that Indicate selected function.

* Short press: Moves up to the next channel or the next menu seleo-

ton;

* Long press: Rapidly traverses up the selections;

[DOWN] Key

* Short press: Moves down to the next channel or the next menu se-

lection;

* Long press: Rapidly traverses down the selections;

17] 18) Antenna Flashlight Power/Volume SP/MIC PTT Button Jack Microphone = Speaker I LCD Display Side Key (1) Side Key (2) FE = Function Key S65 I

@ Function key explanation MENU] Key

+ Short press: enters menu selection mode;

UP] Key

+ Short press: Moves up to the next channel or the next menu selec-

tion;

+ Long press: Rapidly traverses up the selections;

DOWN] Key

+ Short press: Moves down to the next channel or the next menu se-

lection;

+ Long press: Rapidly traverses down the selections;

7|

[EXIT] Key

+ Short press: exits the menu mode;

+ Long press: Lock/unlock all buttons and keys with exception of PTT;

@ LCD display On the display are various indicators that indicate selected function. 7.83 _ Ne AWCT Vv st CH1 CS-MVE5 LCD icon F.oSY battery voltage Ha noise cancelling CH1-CH5S Selected operating channel WX1Wx? Selected NOAA weather channel Key lock Battery indication H/L power (High /H, Low/L) W/H bandwidth (Width/W, Narrow /N) CT/OT CTCSS/DCS YW VOX c Compand Compand function

* Seanning function

* Volee Prompt Nolse cancelling Ml Sido key PTT 3 Push-to-Talk Switch Each side key has two functions depending on a short press and release or a long press and hold. Side Key : Short press Monitor function SQL on/off; long press Flashlight on/off. Side Key2 + Short pres Scanning onvoft long press Nolee Canceling Operation you may begin speaking into the microphone. Is off and the radio Is In receive mode waiting for a ne-

if signal Is properly matched the squelch of the radio will the speaker and voice will be heard. LED indicator is BLUE receiving a carrier only frequency or matched CTCSS or DCS If no vole response is heard verify all radio CTCSS or DCS tone maitched for the channel selected. A press and release of 1 will open tone squelch to monitor a toned channel. 27%

i Main function 151 154 MHz Output power High 2W, Low 1W Waterproof IP65 rating driven rain Flashlight CTCSS/DCS Compand function Scanning function VOX Voice Prompt Vibration Noise cancelling M@ Side key functions

: Each side key has two functions depending on a short press and release or a long press and hold. PTT : Push-to-Talk Switch Side Key1 :

Flashlight on/off. Side Key2 :

on/off. 19]

Short press Monitor function SQL on/off; long press Short press Scanning on/off; long press Noise Cancelling

@ Power ON / Adjust volume Power on radio by rotating the volume switch clockwise; power off by rotating the volume switch counterclockwise.

@ Channel Select Press the [UP / DOWN] key to select the required channel. Hf Transmit / Receive Press and hold the PTT key to transmit, LED indicator light is RED, you may begin speaking into the microphone. Release PTT key, the indicator light is off and the radio is in receive mode waiting for a re-

sponse. If the receive signal is properly matched the squelch of the radio will open the speaker and voice will be heard. LED indicator is BLUE when receiving a carrier only frequency or matched CTCSS or DCS tone. If no voice response is heard verify all radio CTCSS or DCS tone are correctly matched for the channel selected. A press and release of side key 1 will open tone squelch to monitor a toned channel. 110]

Menu Setting BB Menu usage The menu contains the settings of the various functions of the radio. You can manually change the settings in the menu. options function description Press the [Menu] key to enter the menu system

* Select the [UP/DOWN] key to step thru the menu selection list;

* Press the [Menu] key to enter the menu selection setting;

* Press the [UP / DOWN] key to select the setting, then press the a

* [Menu] key to confirm. Press [Exit] key to exit the menu system and retum to the original working mode.

* If no selection is made within 10 seconds, the radio will automati-

cally return to the original working mode. Menu Secondary menu Secondary menu aes pele options function description equals 1W/

peel eee a bend aN Let | been | cioewonen [rem ten bon nee VOX Level Enters saan move, ot least 2 02 Orv prose EXIT to| channels are required to etart scp scan scanning 44)

M@ Menu usage The menu contains the settings of the various functions of the radio. You can manually change the settings in the menu. Press the [Menu] key to enter the menu system

+ Select the [UP/DOWN] key to step thru the menu selection list;

+ Press the [Menu] key to enter the menu selection setting;

+ Press the [UP / DOWN] key to select the setting, then press the

+ [Menu] key to confirm.

+ Press [Exit] key to exit the menu system and return to the original working mode.

* If no selection is made within 10 seconds, the radio will automati-

cally return to the original working mode. M@ Menu List Low power / Low power equals 1W /

90 Power High power high power equals 2W 01 Beep Close/Open Turn offfon beep tones Enters scan mode, at least 2 02 Scan On/ press EXIT to channels are required to start stop scan scanning 03 vox Close/Open Turn off/on automatic PTT voice control for hands free operation. 11]

04 TOT

(Time-out-

timer) Off No limit to transmission talk time. 15sec/.../270sec Sets the maximum time limit for allowed transmission, once timed out a release of the PTT is required to begin another transmission. 05 SQL Level 0-9 Adjust level between 0-9 the higher the level, the stronger the receive signal is required to open the speaker audio. The lower the level enables the radios ability to pick up weak signals. 06 Backlight Close Backlight is off until a key, button press or signal is received. Open Backlight is always on. Automatic 5 seconds/ ... /

seconds 60 Backlight turns off after the set timer expires. 07 VOX Level

(used in conjunction with VOX setting) Close Disables VOX operation. Level 0-9 Sets sensitivy of the microphone for hands free operation with or without a VOX accessory attached. 08 Compand Close/Open Compresses the signal transmitted from the microphone and expands it again at the receiver maximizing the audio signals dynamic range and minimizes noise. 112 Secondary menu Secondary menu Menu 5 5 Secondary menu 5 A Secondary menu options canal neice function description eolection choice function description

(3 options FP options [H Press and hold the EXIT key to lock keys and buttons. Press Roger Close/Open Beep tone signal sent to notify other users a transmission has ended. Picture a 46 | Boot Screen Voltage Chosen feature is displayed upon radio power up. Information Blue flashing LED indicates 17 | Wait Light | Close/Open _ |th radio is powered on waiting for activity when display is not active. 18 Voice Sort Close/Open Used to active voice Prompts to navigate radio settings. 19 | Vibration Close/Open _ | Used to alert channel activity with a low volume setting. 20 Reset Close/Open Reset radio to factory default. Manual and hold a second press to 09 Key Lock unlock. Mode Automatics |Automatically locks keys and seconds /.../30 button after the timer setting seconds expires. Press and hold the EXIT key to remove the timer. Off Dec-CTDCS | CTC-67.0/.../ | Brass [EXIT] key to select: Off, 10 | (Receiver 254.1 CTCSS, DCSN, DCS!;

decode tone) |" 5 CS-po23ni../ a DCS-D7541 Off Ene-CTDCS | CTC-67.0/.../_| press [EXIT] key to select: Off, 11 | (Transmitter 254.1 CTCSS, DCSN, DCS!;

encode tone) 5 cs-po23Ni../

DCS-D7541 Off Battery power save is turned off Extends daily battery life Save Mode between charges. The higher 12 (Battery 444-10 the ratio the longer the radio usage) ua can be used during the day. Note: a high ratio may result in missed calls or words. Turn off or select the desired 13 Power on OffiBeep tone/ tone feature upon turning on tone Chord tone radio power Scan Add/ Delete or add the selected 14 Delete Delete/Add channel to the radio scan list. 13 |

114]

CTCSS / DCS 50 group CTCSS and 108 groups DCS.

[67.0 | 864 | 107.2 | 196.6 | 106.5 | 186.2 | 210.7 | 254.1 |

i=]

oO a oa fe}

a BEEBGEEEEEO BEEGSEGREEE DEEEREDCREG BEEBRECCUEO BEECGEBGEGR BOEBEEBEREER BOEBECBEEER BOROGEDSEEE LT TL | felelelelael 148) Warranty and Service Limited Warranty This product is warranted by BridgeCom Systems, Inc, to be free of defects in materials and workmanship for a period of one year from the date of purchase. If a defective part causes this product to operate improperly during the one-year warranty period, we will service It to the original owner free of charge if shipped to BriigeCom Systems at the owner's expense. This warranty does not apply to any parts damaged due to improper use or violation of Instructions. It does not extend to damage incurred by misuse or abuse, unauthorized modifications, natural causes such

@8 lightning, fire, floods, and other such catastrophes; nor to damage caused by environmental exiremes, such as power surges and/or tran-

stents, theft, or accidents, All warranties must be performed at BridgeCom Systems, Inc. No credit will be given for unauthorized repair work atbempted by the cus-

tomer. BridgeCom Systems, Inc. will repair or replace the equipment and return to the customer freight pre-paid, within the continental United States. Equipment found net to be defective will be retumed at the customer's expense, and It will include the cost to ship, test, and Feturn the equipment. Equipment returned for repair must have a return merchandise autho-

rization (RMA) number. To obtain an RMA contact our Technical Sup-

port Department at (636)-206-1736 or email techsupport@BridgeCom-

Systems.com. All returned equipment must have the RMA number listed on the outside of the shipping container. Ship all returns to: BridgeCom Systems, Ino, Atin: Repair 113 South Brkige Street Smithville, MO 64089 Out of warranty repairs and ser-

vice charges are billed at the current hourly rate plus parts. PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE. 50 group CTCSS and 105 groups DCS. 67.0 | 85.4 | 107.2 | 136.5 | 165.5 | 186.2 | 210.7 | 254.1 69.3 | 88.5 | 110.9 | 141.3 | 167.9 | 189.9 | 218.1 71.9 91.5 | 114.8 | 146.2 | 171.3 | 192.8 | 225.7 74.4 94.8 | 118.8 | 151.4 | 173.8 | 196.6 | 229.1 77.0 97.4 | 123.0 | 156.7 | 177.3 | 199.5 | 233.6 79.7 | 100.0 | 127.3 | 159.8 | 179.9 | 203.5 | 241.8 82.5 | 103.5 | 131.8 | 162.2 | 183.5 | 206.5 | 250.3 023 | 065 | 132 | 205 | 255 | 331 | 413 | 465 | 612 | 723 025 | 071 | 134 | 212 | 261 | 332 | 423 | 466 | 624 | 731 026 | 072 | 143 | 223 | 263 | 343 | 431 | 503 | 627 | 732 031 | 073 | 145 | 225 | 265 | 346 | 432 | 506 | 631 | 734 032 | 074 | 152 | 226 | 266 | 351 | 445 | 516 | 632 | 743 036 | 114 | 155 | 243 | 271 | 356 | 446 | 523 | 645 | 754 043 | 115 | 156 | 244 | 274 | 364 | 452 | 526 | 654 047 | 116 | 162 | 245 | 306 | 365 | 454 | 532 | 662 051 | 122 | 165 | 246 | 311 | 371 | 455 | 546 | 664 053 | 125 | 172 | 251 | 315 | 411 | 462 | 565 | 703 054 | 131 | 174 | 252 | 325 | 412 | 464 | 606 | 712 115]

Limited Warranty This product is warranted by BridgeCom Systems, Inc. to be free of defects in materials and workmanship for a period of one year from the date of purchase. If a defective part causes this product to operate improperly during the one-year warranty period, we will service it to the original owner free of charge if shipped to BridgeCom Systems at the owners expense. This warranty does not apply to any parts damaged due to improper use or violation of instructions. It does not extend to damage incurred by misuse or abuse, unauthorized modifications, natural causes such as lightning, fire, floods, and other such catastrophes; nor to damage caused by environmental extremes, such as power surges and/or tran-

sients, theft, or accidents. All warranties must be performed at BridgeCom Systems, Inc. No credit will be given for unauthorized repair work attempted by the cus-

tomer. BridgeCom Systems, Inc. will repair or replace the equipment and return to the customer freight pre-paid, within the continental United States. Equipment found not to be defective will be returned at the customer's expense, and it will include the cost to ship, test, and return the equipment. Equipment returned for repair must have a return merchandise autho-

rization (RMA) number. To obtain an RMA contact our Technical Sup-

port Department at (636)-205-1736 or email techsupport@BridgeCom-

Systems.com. All returned equipment must have the RMA number listed on the outside of the shipping container. Ship all returns to: BridgeCom Systems, Inc. Attn: Repair 113 South Bridge Street Smithville, MO 64089 Out of warranty repairs and ser-

vice charges are billed at the current hourly rate plus parts. PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE. 116 |

This Gocument contains information proprietary to Brage Embedced Systems, Inc., BridgelP, LLC and BridgeCom Systems, Inc, Its con-

tents may not be reproduced, in whole or in part, without express writ-

ten permission from either Bridge Embedded Systems, Inc., BridgelP, LLG or BrkigeCom Systems, Inc. The information is provided AS |S without warranty of any kind, either expressed or implied. BridgeCom Systems, Inc. does not assume any liability for damages. Technical information and specifications in this document are subject to change without notice. Changes or modifications to this device not expressly approved by BridgeCom Systems could void the users au-

thorization to operate this device. 147) This document contains information proprietary to Bridge Embedded Systems, Inc., BridgelP, LLC and BridgeCom Systems, Inc. Its con-

tents may not be reproduced, in whole or in part, without express writ-

ten permission from either Bridge Embedded Systems, Inc., BridgelP, LLC or BridgeCom Systems, Inc. The information is provided AS IS without warranty of any kind, either expressed or implied. BridgeCom Systems, Inc. does not assume any liability for damages. Technical information and specifications in this document are subject to change without notice. Changes or modifications to this device not expressly approved by BridgeCom Systems could void the users au-

thorization to operate this device. 117]

FCC Statement:

Any Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. SAR tests are conducted using standard operating positions accepted by FCC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. Before a new model is a available for sale to the public, it must be tested and certified to the FCC that is does not exceed the exposure limit established by the FCC. Tests for each product are performed in positions and locations as required by the FCC. For body worn operation, this device has been tested and meets the FCC RF exposure guidelines when used with and accessory designated for this product or when used with and accessory that contains no metal. To maintain compliance with FCC RF exposure guidelines hold the transmitter and antenna at least 1 inch (2.5 centimeters) from your face and speak in a normal voice, with the antenna pointed up and away from the face. The equipment complies with FCC radiation exposure limits set forth for and uncontrolled environment. In order to comply with the FCC RF exposure requirement, the antenna installation must comply with following:

Users must be fully aware of the hazards of the exposure and able to exercise control over their RF exposure to qualify for the higher exposure limits. Your wireless hand-held portable transceiver contains a low power transmitter. This product sends out radio frequency (RF) signals when the Push-to-Talk(PTT) button is pressed. The device is authorized to operate at a duty factor not to exceed 50%. ridge Y'

BridgeCoyy) Printed in China

Bra gec on SYSTEMS Model Bes-ves Power.2W [D) Frequency:151.820-14.600MHz IT TVEUAL TLE THILL A S/N:BCSMV650001 sitenton: Restricted to uncontrolled Ayres FCC RF exposure lit, See user manual for opetaig requirements FCC ID:SK4BCS-MV65

BridgeIP, LLC Address: 113 S. Bridge St., Smithville, Missouri, 64089 United States Tele: 8165328451 FAX: 816-532-8451 E-mail: ron@bridgecomsystems.com Attestation Letter Date: 10/10/2023 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 2.911(d)(5)(i)(ii) Filing FCC ID: SK4BCS-MV65 BridgeIP, LLC (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. BridgeIP, LLC (the applicant) certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely, Signature Contact Person: Ron Kochanowicz Title: Manager CFR 47 2.911(d)(5)(i)(ii) Attestation Letter

BridgeIP, LLC Address: 113 S. Bridge St., Smithville, Missouri, 64089 United States Tele: 8165328451 FAX: 816-532-8451 E-mail: ron@bridgecomsystems.com DECLARATION Date: 2023-10-10 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam:

We declare that our product: WALKIE TALKIE ( MURS radio) (model: BCS-MV65, FCC ID: SK4BCS-MV65).The product has locked the TX frequency to 151.820MHz, 151.880 MHz,151.940 MHz,154.570 MHz,154.600MHz by firmware, then end-users could not unlock the limited band out of range neither by software programming on PC nor manually programming. It will get failed message if the end users program the TX range out of the frequency 151.820MHz, 151.880 MHz, 151.940 MHz, 154.570 MHz, and 154.600MHz. Sincerely, Signature:

Contact Person: Ron Kochanowicz Title: Manager

BridgeIP, LLC Address: 113 S. Bridge St., Smithville, Missouri, 64089 United States Tele: 8165328451 FAX: 816-532-8451 E-mail: ron@bridgecomsystems.com FCC Authorization Date: 2023-10-10 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

We , BridgeIP, LLC, Hereby authorizes China Certification ICT Co., Ltd (Dongguan) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by China Certification ICT Co., Ltd (Dongguan) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Clients signature Contact Person: Ron Kochanowicz Title: Manager QA-FR-170-B

BridgeIP, LLC Address: 113 S. Bridge St., Smithville, Missouri, 64089 United States Tele: 8165328451 FAX: 816-532-8451 E-mail: ron@bridgecomsystems.com FCC Confidential Authorization Date: 2023-10-10 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: SK4BCS-MV65 In accordance with Sections 0.457 and 0.459 of the Commissions Rules, BridgeIP, LLC hereby requests long-term confidential treatment of information accompanying this application as outlined below:

Block Diagram Schematics Operation Description BOM Tune Up Procedure The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature:

Contact Person: Ron Kochanowicz Title: Manager QA-FR-171-A

U.S. AGENT LETTER OF ATTESTATION Date: 2023-10-10 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 2.911(d)(7) Filing FCC ID: SK4BCS-MV65 BridgeIP, LLC (the Applicant) certifies that, as of the date of the filing of the application, BridgeIP, LLC (U.S. agent). is our designated U.S. agent for service of process for the above referenced FCC ID. BridgeIP, LLC (the Applicant) accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. BridgeIP, LLC (U.S. agent) accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent and Applicant Information:

Name: BridgeIP, LLC Address: 113 S. Bridge St., Smithville, Missouri, 64089 United States FRN: 0011618444 Tel.: 8165328451 Email: ron@bridgecomsystems.com Signed by (printed name): Ron Kochanowicz Signature: