PH44/PH80 Quick Start Guide Product Features PH44 Reset Button Power Button PH80 1 2 3 4 1 2 4 1 2 3 4 Power Indicator RJ45 Port 1 to Port 4 Indicator (PH44 Only) RJ45 Port 1 to Port 8 Indicator (PH80 Only) RJ11 Port 5 to Port 8 Indicator (PH44 Only) For PanL Sensor Device System Health Indicator:
Refer to the section PH44/80 System Health LED Indicator for details Product Specifications
* There is no RF modules for PanL Hub Basic models PD4400 and PD8000. Connect to wired devices only. Please visit http://panlshop.com/warranty or scan the QR code for warranty registration with the UUID and Product Key below:
1. Hub Setup Place hub based on below recommendations:
A. Ensure the availability of an AC outlet nearby; B. Place on a flat surface area in an upright position; C. Best to be placed in an open area with good ventilation; D. Best to be positioned central to all wireless devices (if any); E. Place near router if using wired Ethernet connection. F. Apply screws to the sides of the hub to secure the hub. 2. Attach a power plug cable to the power adaptor provided and connect to the hubs power jack. Switch on the power button located at the side of the hub. For applications which are required to be connected to the Internet or a local network, the hub can be connected to a local router through
(Ethernet cable not provided). Alternatively the hub can also be connected to the router if the Wi-Fi RF module is present in the hub model. the Ethernet port 3. 4. Connect any PanL wired devices to the hub through the RJ45 ports or RJ11 ports for PanL sensors. Ensure that the length of the RJ45 cables does not exceed 100 Metres from the port to the wired device. In the event that a single port is used to power up a few PanL devices in a daisy chain configuration, the total combined cable length must not exceed 100 Meters. For RJ11 ports, the cable length must not exceed 50 Meters from the port to PanL sensor device. For more details on wired device connections, refer to the respective device quick start guide. RJ45 Ports RJ11 Ports Ethernet Port PH44 Power Jack RJ45 Ports Power Jack Ethernet Port PH80 5. Any unused RJ45 ports must be connected to the terminators provided. 6. Any active wireless devices within the operating range of the hub will be automatically detected (Refer to the Product Specifications section to check the wireless protocols supported). STICKER AREA PH44/PH80 Quick Start Guide PH44/80 System Health LED Indicator Hub Status Description System Health LED Indicator LED 9 LED 10 Unconfigured Hub Mode
(Please refer to the User Manual for configuration) Boot up Normal Operation Mode Re-Boot/ Shutdown Factory reset or firmware rollback Factory reset or roll back failed
(Manually power off and on hub to reboot) Network link missing
(Check if Ethernet cable is connected or hubs Wi-Fi is configured) Hub Temperature is above the threshold value
(Alert notification will be sent to and Hub will shut down) Green blinking Green Blinking Green Blue blinking Yellow Blinking Blue blinking Green Red Blinking Green blinking Green Green Green Yellow Blinking Blue blinking Red Red Blinking The Hubs control menu cab be accessed through the [Reset] button located at the side of the hub to trigger certain actions:
Action Activate Control Menu Function Selection Reboot System Shutdown Instruction To activate control menu, do a long press on the [Reset] button until the System Health LED indicators (LED 9 and 10) are flashing in green. Do an immediate short press again to enter into the control menu. LED 1-4 flashes green indicating control menu is successfully triggered. After successfully triggering the control menu, the corresponding 4 functions below can be toggled by doing short presses on the
[Reset] button, this will be reflected on LED 1-4. 1)Rollback to previous firmware 2)Set Hub back to un-configured state 3)Reset Hub to Factory Settings 4)Go back to selection (1) Once the desired function is selected, simply do a long press and the selected LED will change from green to yellow indicating that the function desired is successfully executed. If there is no input selection for a period of time, the hub will return to the normal operation mode. To perform a reboot function, simply do a short press (3-5 seconds) on the [Reset] button. To perform a system shutdown, simply press the [Reset] button for more than 5 seconds and release. LED 9 will be flashing blue while LED 10 will be flashing green indicating a successful shutdown. Whats in the Box?
The package includes a PH44/PH80 Hub, a 24V DC power adaptor and 4/8 terminators for PH44/PH80 respectively. The power plug cable is not included in the box and may be packed outside the box separately. 24V DC Power Adaptor PH44/PH80 Terminator Adaptor Model#
SSA-0601HE Power Ratings 24VDC 2.5A GST120A24-P1M 24VDC 5.0A PH44 PH80 FCC Statements This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCCs RF exposure guidelines, at least (To be updated based on MPE report) cm of separation distance between the PanL Hub44 device and the user's body must be maintained at all times.