all | frequencies |
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 3 |
|
User Manual | Users Manual | 2.52 MiB | ||||
1 2 3 |
|
User Manual 1 of 2 | Users Manual | 3.88 MiB | May 08 2005 | |||
1 2 3 |
|
User Manual 2 of 2 | Users Manual | 2.22 MiB | May 08 2005 | |||
1 2 3 | Cover Letter(s) | May 08 2005 | ||||||
1 2 3 | Cover Letter(s) | May 08 2005 | ||||||
1 2 3 | Test Report | May 08 2005 | ||||||
1 2 3 | Test Setup Photos | May 08 2005 | ||||||
1 2 3 | Parts List/Tune Up Info | |||||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 | Parts List/Tune Up Info | |||||||
1 2 3 | External Photos | |||||||
1 2 3 | ID Label/Location Info | |||||||
1 2 3 | Internal Photos | |||||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 | Test Setup Photos |
1 2 3 | User Manual | Users Manual | 2.52 MiB |
Preliminary & Confidential making connections in a high-speed world Wireless Gigabit Ethernet Link Model GE60 Installation Manual P/N 580-00505 Revision 0.4 March 2004 1 of 30 TM Copyright Notice & Disclaimer GE60 Installation Manual Copyright 2004 BridgeWave Communications. All rights reserved. Printed in the USA No portion of this publication may be reproduced, copied, or distributed without the written consent of BridgeWave Communications. BridgeWave reserves the right to update or change the material in this publication at any time without notice. BridgeWave has made every effort to ensure that the information and the instructions contained in the publication are adequate and is not responsible for any errors or omissions due to typing, printing, or editing of this document. Purchasers of BridgeWave products should make their own evaluation to determine the suitability of each such product for their specific application. BridgeWaves obligations regarding the use or application of its products shall be limited to those commitments to the purchaser set forth in its Standard Terms and Conditions of Sale for a delivered product. This publication has been prepared for professional and properly trained personnel, and the customer assumes full responsibility when using the information herein. Revision History Issue Date 0.1 0.2 0.3 0.4 Main changes Preliminary draft for comments 8/19/03 12/12/03 Changes incorporated 01/12/04 Pictures added and additional changes incorporated 03/04/04 Added detail on Polyphaser circuit protector in Section 2.7 &
loopback testing impact on Fiber LED in Section 3.8 item #8 580-00505, rev 0.4 2 of 30 PRELIMINARY TM Statement of Warranty GE60 Installation Manual BridgeWave warrants each standard BridgeWave Product sold by it to be free of defects in material and workmanship under conditions of normal use for twelve (12) months from date of shipment thereof to Buyer. Repair or, at BridgeWaves option, replacement of defective parts shall be the sole and exclusive remedy under this limited warranty;
provided that BridgeWave may, as an alternative, elect to refund the purchase price amortized on a straight-line basis over a period of three (3) years from the date of shipment. All warranty replacement or repair of parts shall be limited to equipment malfunctions, which, in the sole opinion of BridgeWave, are due or traceable to defects in original materials or workmanship. In the event Buyer believes that Products do not conform to the limited warranty of this Section, Buyer shall pay for the shipping and insurance of such Product to BridgeWave. If BridgeWave determines in its sole opinion that such Products do not conform to the limited warranty, then BridgeWave shall pay for the shipping and insurance of repaired or replacement Products to Buyer. However, in the event that BridgeWave determines in its sole opinion that such Products conform to the limited warranty, Buyer shall pay for shipping and insurance of such Products back to Buyer. All obligations of BridgeWave under this limited warranty shall cease in the event of abuse, accident, alteration, misuse or neglect of the Product. In-warranty repaired or replaced parts are warranted only for the remaining unexpired portion of the original warranty period applicable to the repaired or replaced parts. REASONABLE CARE MUST BE USED TO AVOID HAZARDS. BRIDGEWAVE EXPRESSLY DISCLAIMS RESPONSIBILITY FOR LOSS OR DAMAGE CAUSED BY USE OF ITS PRODUCTS OTHER THAN IN ACCORDANCE WITH PROPER OPERATING PROCEDURES. THE FOREGOING LIMITED WARRANTY FOR BRIDGEWAVE PRODUCTS IS EXPRESSLY IN LIEU OF, AND EXCLUDES ALL OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR PARTICULAR PURPOSE, USE OR APPLICATION, AND ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF BRIDGEWAVE, UNLESS SUCH OTHER WARRANTIES, OBLIGATIONS OR LIABILITIES ARE EXPRESSLY AGREED TO IN WRITING BY BRIDGEWAVE. Statements made by any person, including the representatives of BridgeWave, which are inconsistent or in conflict with the terms of these warranties shall not be binding upon BridgeWave unless expressly reduced to writing and approved by an officer of BridgeWave. 580-00505, rev 0.4 3 of 30 PRELIMINARY TM Product Compatibility GE60 Installation Manual While every effort has been made to verify operation of this product with many different communications products and networks, BridgeWave makes no claim of compatibility between its products and other vendors equipment. It is assumed that users have thoroughly evaluated this products performance in the communications environment in which it will be used. Safety CAUTION, WARNING, and DANGER statements have been strategically placed in the text to alert personnel of possible hazards. These statements must be closely observed. The following general safety precautions must be observed during all phases of operation and service of the products covered in this manual. Failure to comply with these precautions or with specific warnings elsewhere in this manual willfully violates standards of design, manufacture, and intended use of the product. BridgeWave assumes no liability for the customers failure to comply with these requirements. Do not operate wireless equipment without an appropriate termination. Do not work directly in front of an energized antenna. Prior to working on the antenna or RF assembly, ensure that the RF assembly is not radiating energy. When power is applied to the RF assembly and antenna, proper precautions must be taken to avoid placing any part of the human body in front of the antenna. The outdoor equipment must be properly grounded to provide some protection against voltage surges and built-up static charges. In the event of a short circuit, grounding reduces the risk of electrical shock. For installations in the U.S.A., refer to Articles 810830 of the National Electrical Code, ANSI/NFPA No. 70, for information with respect to proper grounding and applicable lightning protection for DC cables. For installations in all other countries, implement protection in accordance with the safety standards and regulatory requirements of the country where the equipment is to be installed. Do not install or operate this equipment in the presence of flammable gases or fumes. Operation of any electrical instrument in such an environment constitutes a definite safety hazard. 580-00505, rev 0.4 4 of 30 PRELIMINARY TM GE60 Installation Manual Do not install substitute parts or perform any unauthorized modification to the equipment. Changes or modifications not expressly approved by BridgeWave can void the users authority to operate the equipment. Regulatory Information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference that may cause undesired operation. Equipment Precautions Water and Moisture - The GE60 is designed to withstand moisture conditions typically encountered when installed outdoors. They are not designed for operation under water. Power Sources - This product should be operated only from the type of power source indicated on the unit or in the manual. 580-00505, rev 0.4 5 of 30 PRELIMINARY TM 1 Introduction 1.1 Purpose of Manual GE60 Installation Manual The information in this manual is directed to persons who must perform or coordinate the tasks associated with the process of installing wireless communication devices, and planning communication network applications. 1.2 Prior Knowledge This manual assumes the operator has at least basic experience with and understanding of the concepts underlying telecommunications systems, as well as some familiarity with configuring and operating networking equipment. Preferably, the installer/operator fully understands the information covered in this manual prior to attempting these procedures. While this manual summarizes the considerations and tasks involved in path analysis and site planning for radio systems, it does not provide an in-depth treatment of such issues. A professional agency specializing in this area should be consulted for additional information and services of this type. DANGER!
the given instruction. A DANGER statement will describe the potential hazard, its possible consequences, and the steps to perform to avoid personal injury. Indicates that personal injury can result if the user does not comply with Indicates that serious damage to the equipment can result if the user does WARNING!
not comply with the given instruction. A WARNING statement will describe the potential hazard, its possible consequences, and the steps to perform to avoid serious equipment damage. CAUTION!
Indicates that equipment damage, process failure, and/or loss of data can result if the user does not comply with the given instruction. A CAUTION statement will describe the potential hazard, its possible consequences, and the steps to perform to avoid equipment damage, process failure, and/or loss of data. NOTE: Provides supplementary information to emphasize a point or procedure, or gives a tip for easier operation. 580-00505, rev 0.4 6 of 30 PRELIMINARY TM 1.3 Contact Information GE60 Installation Manual Technical Assistance and Customer Service BridgeWave distributors are authorized local service providers and are responsible for immediate customer support. If problems are not resolved, contact BridgeWave Customer Service for assistance:
Santa Clara, CA USA 408.567.6900 Tel:
408.567.0775 Fax:
Email:
support@bridgewave.com Return Material Authorization (RMA) Should BridgeWave equipment have to be returned for repair or replacement, an RMA number must be obtained from BridgeWave or the local BridgeWave distributor. When returning equipment, be sure to write the RMA number on the outside of the shipping carton. 580-00505, rev 0.4 7 of 30 PRELIMINARY GE60 Installation Manual TM 2 Site Planning 2.1 General Before the start of an installation a survey should be conducted of the proposed area of the site(s). The survey personnel should be fully familiar with the details required to install the GE60 radio system. 2.2 Equipment Checklist The survey team will need the following equipment:
Binoculars GPS Navigation Device Tape Measure Site Survey Report Form 2.3 Line of Sight (LOS) The GE60 Wireless Gigabit Ethernet link requires Line-of-Sight for proper operation. Fortunately, the links are relatively short and obstructions in the path can easily be identified. Binoculars can ease viewing in poor light conditions. The planning should include an investigation into future building plans that could block the LOS path, and other long-term incremental obstructions such as trees. Intermittent obstructions such as aircraft at a nearby airport should also be considered. The minimum required clearance from obstacles is 60% of the first Fresnel zone. Fresnel zones are a series of concentric ellipsoid areas surrounding the straight-line path between two antennas. The first Fresnel zone is the area containing every point of which the distance from the transmitter to any reflection point on the area and on to the receiver is half a wavelength longer than the path of the direct signal. The radius of the Fresnel zone is greatest at midpoint in the signal path. MinimumCle arance
meters
005.0 D 1(
) where, D = Path distance in meters
= Distance from antenna as a percentage of path distance 580-00505, rev 0.4 8 of 30 PRELIMINARY TM GE60 Installation Manual Path Length
(meters) Minimum Clearance
(meters) 250 500 750 1000 0.56 0.79 0.97 1.12 Table 2-1: Minimum Clearance at Link Midpoint for various Path Lengths 2.4 Link Distance Measurement of the link distance is important in estimating the link availability and calculating expected Receive Signal Level (RSL). This measurement can be performed using the Latitude and Longitude readings from a Global Positioning System (GPS) device, which is placed near the proposed locations of the antennas, or using a range finder device. Table 2-2 below lists the maximum link distance with respect to desired availability and ITU rain zone (ITU-R Recommendation PN.837). The map (Figure 2-1) following the chart shows where the rain zones fit across North America and Asia for various availabilities and most ITU rain zones. Rain Zone Availability 99.7000%
99.9000%
99.9700%
99.9900%
99.9950%
99.9970%
99.9990%
A 837 817 782 752 717 702 652 B 817 802 772 717 677 657 602 C 807 782 742 697 647 587 567 E 812 772 717 652 592 567 487 F 787 752 697 622 552 527 467 K 787 717 647 567 502 487 427 M 727 652 572 502 452 437 402 N 697 592 497 437 392 377 337 D 787 752 712 672 632 617 567 Table 2-2: Maximum Link Distances (meters) for various Availabilities and Rain Zones 580-00505, rev 0.4 9 of 30 PRELIMINARY TM GE60 Installation Manual Figure 2-1: Rain Zone map for North America Figure 2-2: Rain Zone map for Asia 580-00505, rev 0.4 10 of 30 PRELIMINARY TM 2.5 Antenna Location GE60 Installation Manual The optimum location for the antennas must be determined. The ideal location should provide for ease of erecting and mounting the antenna, as well as unimpeded Line-Of-
Site (LOS) to the other site. The following factors should be taken into account:
Type of mountingwall or pole Length of cable runs Grounding connection points Obstructions Accessibility 2.6 Cabling The installation site should be inspected to determine the run paths for the fiber cable and power cable from the radio equipment to the termination point. Locations for roof penetration should be identified. The routing and securing of all cables should conform to all applicable codes and requirements. Depending on the likelihood of damage due to foot traffic or equipment movement, cabling conduit may be required. The maximum cable run length as specified for the equipment being installed must not be exceeded. Our radio requires an LC type connector on the multi-mode fiber to properly connect the fiber to the radio. Single-mode fiber is not a current option supported by the radio. The type of fiber connector (typically either LC or SC) required on the other end of the fiber that connects to the applicable Gigabit Ethernet switch, router, or bridge will depend upon the interface on your applicable networking equipment. The GE60 radio includes a 100-240 VAC power adaptor that converts the AC voltage from the standard electrical outlet in the wall to DC voltage. Our radio requires a minimum of 13.5 VDC (24.0 VDC maximum) up the power cable to the radio to function properly. When planning the cable run from indoor mounted AC power adaptor to the radio unit, it is critical to select the cable AWG to ensure adequate voltage at the radio. Fiber Cable Length Cable Type
(meters) Up to 270 Up to 500 62.5/125 m 50/125 m Table 2-3: Fiber Cable Types 580-00505, rev 0.4 11 of 30 PRELIMINARY TM GE60 Installation Manual DC Cable Length
(meters) Up to 100 Up to 150 Up to 250 Up to 300 Up to 550 Minimum Cable Size (AWG) Power Supply
@ 18VDC Power Supply
@ 24VDC 16 14 12
Table 2-4: Minimum DC Cable Size 18 18 16 14 12 2.7 Grounding & Lightning Protection Indicates that serious damage to the equipment can result if the user does WARNING!
not comply with the given instruction. A WARNING statement will describe the potential hazard, its possible consequences, and the steps to perform to avoid serious equipment damage. Proper grounding of the outdoor equipment reduces electromagnetic interference, provides lightning protection, and protects against electrical discharge. The source and connection points for the building-to-earth ground in the vicinity of the antenna location should be determined. A 5 (1.5m) copper cable is provided with each radio for a ground cable to allow the radio to be grounded to the applicable pole or to the mount in the event a pole is not used for the installation. The pole or mount, as applicable, will need to be connected to the building ground. In addition to grounding the equipment, local building codes may require the DC electrical cable to be protected from lightning strikes. In the event your local city or county requires such a device you may use a Polyphaser circuit protector model # IS-
PSP-24, manufactured by Polyphaser Corporation (or equivalent model from another manufacturer). The Polyphaser device is available from the following companies:
TESSCO MD & NV 800-472-7373 Talley Communication CA 800-949-7099 Hutton Communication TX 877-648-8866 IL Primus 800-435-1636 TEDI FL 800-729-8334 2.8 Environmental The structure to which the equipment will be mounted should be adequate to bear all wind and other weather conditions. The environmental conditions at the location must conform to the operating environment specified for the equipment. 580-00505, rev 0.4 12 of 30 PRELIMINARY TM GE60 Installation Manual 2.9 Simple Network Diagram Following is a diagram detailing the equipment and cabling found on a typical installation of BridgeWaves 60GHz radio equipment. High-Band Radio Vertical Polarization Low-Band Radio Vertical Polarization Gig-E Switch or Roter LAN/
WAN Fiber Optics Cable Indoor Power Supply Path between radios Gig-E Switch or Roter Fiber Optics Cable DC-Power Cable DC-Power Cable Indoor Power Supply LAN/
WAN 580-00505, rev 0.4 13 of 30 PRELIMINARY GE60 Installation Manual TM 3 Installation 3.1 General It is recommended that installation personnel read this section in its entirety prior to installing the BridgeWave System. During a particular phase of installation, the user may refer directly to the applicable subsection. The Installation section is comprised of seven subsections covering the procedures and guidelines for installing the BridgeWave Radio System. Subsections 3 through 3.4 contain information necessary to prepare for the equipment installation. Subsection 3.5 through 3.7 covers equipment installation procedures. Subsection 3.8 and 3.9 contains information necessary for aligning the antennas. 3.2 Equipment Packing & Unpacking The radio system equipment will arrive in two boxesone box for the low band radio and one box for the high band radio. Locate the correct box (low band or high band) before beginning installation by checking the label on the outside of the box or on the radio itself. It is recommended that the shipping cartons and packing materials be retained in the event that it is necessary to return any equipment. 3.3 Equipment Inventory Each carton is accompanied by a packing list. Verify the contents of the carton against the packing list. Following are inventory lists for a typical system. Qty Description 1 ea. GE60 Radio (Low band or High band) 1 ea. Wall Mount Bracket 1 ea. AC Power Adapter 1 ea. GE60 Pole Mount Kit (optional) 580-00505, rev 0.4 14 of 30 PRELIMINARY TM GE60 Wall Mount Kit Parts List Item Description 1 2 3 4 5 6 Mount Bracket Radio Yoke Bracket Shim Split Lock Washer Flat Washer
-16 x bolts GE60 Pole Mount Kit Parts List Item Description Pole Clamp
-16x9in Threaded Rod Split Lock Washer Flat Washer
-16 Hex Nut
-16 x bolts 1 2 3 4 5 6 GE60 Installation Manual Qty. 1 1 1 2 2 2 Qty. 4 4 14 (2 spares) 14 (2 spares) 8 6 (2 spares) Tampering with seals will void the warranty. CAUTION!
Notice the warranty stickers on the inner (metal) cover of the radio. The radio is sealed at the factory. There is no need to open this cover in the field. Tampering with these seals will void the warranty. 3.4 Installation Tools The following tools should be on hand for installing the radio system:
Screwdriver, Slotted 0.1 inch (2.5mm) wide Open-End Wrench 9/16 (14mm), 2 ea. Ratchet w/ 6in (15cm) extension and 9/16 (14mm) deep socket Wire Stripper/Cutter (10-16 gauge) Electrical Tape Fish tape for pulling cable Cable Tie Wraps Hand-Held VOM (voltmeter) with standard probes 580-00505, rev 0.4 15 of 30 PRELIMINARY TM GE60 Installation Manual 3.5 Radio Mount Installation Wall Mounting 1. 2. Install 4 mounting bolts in the wall at the desired location using the template provided (see Figure 3-4 below). The bolts (normally -16) should extend 0.8 to 3.0 inches (2cm to 7.5cm) from the wall and be strong enough to secure the radio to the wall under foreseeable environmental conditions. The environmental conditions may include, but not limited to, wind, rain, ice, etc. Depending on the wall material the mount is being attached to, a different size bolt may be appropriate. In this case, bolts up to inch in diameter may be used. Secure the mount to the bolts using the appropriate sized nuts, lock washers, and flat washers for the bolts used to mount the bracket. Figure 3-1: Mount in Wall Mount Configuration 580-00505, rev 0.4 16 of 30 PRELIMINARY TM GE60 Installation Manual 3. Attach the radio yoke to the mount, with brass shim in-between, using 2 each of the supplied -16 x bolts, lock washers, and flat washers. Tighten the bolts just enough that the yoke can move back and forth without binding. 3/8-16x3/4 Bolts 3/8 Lock Washer 3/8 Flat Washer Mounting Bracket Brass Shim Radio Yoke Pole Mounting The optional pole mount kit can be used to secure the mount a pole with diameters of 2.0 to 4.5 inches (5cm to 11cm). 1. Attach two of the pole clamps to the mounting bracket using 4 each -16 x bolts, lock washers, and flat washers. Attach the threaded rods to the pole clamps using 8 -16 nuts and 4 each lock washers and flat washers. Refer to Figure 3-2. Secure the mount to the pole using two pole clamps and 4 each -16 nuts, lock washers, and flat washers. 2. 3. Attach the radio yoke as described above. 580-00505, rev 0.4 17 of 30 PRELIMINARY TM GE60 Installation Manual Figure 3-2: Mount with Radio Yoke in Pole Mount Configuration Figure 3-3: Side view of mount with Radio Yoke in Pole Mount Configuration 580-00505, rev 0.4 18 of 30 PRELIMINARY TM GE60 Installation Manual 6.25 inches
(15.9 cm) 3.13 inches
(8.0 cm) Figure 3-4: Template Radio Mounting bolts 580-00505, rev 0.4 19 of 30 PRELIMINARY TM GE60 Installation Manual 3.6 Radio Installation 1. Remove the up/down adjustment bolts from the radio. Place the radio in the yoke the two up/down pivot bolts should rest in the Us cut in the yoke. Note that when the radio comes from the factory, the mounting plates are in the vertical polarization position, that is, the diamond marking on the radio (see insert below) on the front of the radio housing is to the right when viewed from the front. For horizontal polarization, the mounting plates should be moved so that the diamond is at the top when viewed from the front. Polarization Diamond orientations: Horizontal (Left) and Vertical (Right) See Figure 3.7 for further explanation and visual image of Horizontal vs Vertical polarization. Indicates that equipment damage, process failure, and/or loss of data can CAUTION!
result if the user does not comply with the following given instruction. A CAUTION statement will describe the potential hazard, its possible consequences, and the steps to perform to avoid equipment damage, process failure, and/or loss of data. It is critically important during installation to ensure the radios on each side of the link are in the same polarization (i.e., Horizontal-Horizontal or Vertical-Vertical). A link that has a radio on one side of the link set in the Horizontal polarization and the other side of the link set in the Vertical polarization will not operate properly. Further, it is also critically important that a High-Band radio is paired with a Low-Band radio to ensure the system will operate properly. Prior to installation check each radio to verify one is a High-Band and the other is a Low-Band version. The label on the side of the radio will indicate whether it is a High-Band or Low-Band version. 580-00505, rev 0.4 20 of 30 PRELIMINARY TM GE60 Installation Manual Figure 3-5: Inserting Radio Into Yoke 2. Reinsert the up/down adjustment bolts, through the channel in the yoke. Tighten the up/down pivot bolts enough such that the finger cam is behind the tab at the front of the yoke. Turn the finger cam clockwise until tight. With the cam tightened, the pivot bolt is prevented from any front/back movement. Figure 3-6: Detail of Up/Down Pivot & Adjustment Bolts and Finger Cam 580-00505, rev 0.4 21 of 30 PRELIMINARY TM GE60 Installation Manual 3.7 Cable Installation 1. Fiber Cabling Install a duplex multi-mode fiber from the radio to the network termination equipment (switch or router with 1000Base-SX port). The connectors on the radio end of fiber require LC connectors; the connectors on the switch/router end should mate to the network equipment. 2. Connect fibers at the network equipment. 1. 2. 3. Power Cabling Select indoor location, with easy cable routing to the radio, for the AC power adaptor. Normally it is convenient, but not required, to place the adaptor near the network termination equipment. Select the appropriate wire gauge based on the estimated cable length required AC adaptor location to radio, see Table 2-4. Install the DC power cable and attach to the AC adaptor using the supplied terminal block. Do not plug-in the AC adaptor at this time. Figure 3-7: Front view of fiber and power cable installed (Note: Radio is shown in the Horizontal polarization as the diamond is on the top) 580-00505, rev 0.4 22 of 30 PRELIMINARY TM GE60 Installation Manual Figure 3-8: Inside view of fiber and power cable connected Note that the fiber cable is inserted through the straight-through fitting on the left and the power cable is inserted through the fitting on the right. Both the cables have been looped around the inside of the enclosure to minimize tension on the cables when connected to the radio. 1. Attach the lug of the copper ground cable provided with the radio to one of the two Ground Cabling
#8 holes at the bottom of the radio using a #8-32 bolt, #8 lock washer and #8 flat washers. 2. Connect other end of the ground cable to a nearby grounding location. 580-00505, rev 0.4 23 of 30 PRELIMINARY TM GE60 Installation Manual 3.8 Visual Alignment 1. 2. 3. 4. Tighten mounting bolts just enough to allow radio to pivot up/down and right/left with minimal effort. Tilt the radio so that it is roughly point towards the other end of the link. Insert the Visual Alignment Tool (VAT) into one of the 4 holes in the front
(antenna) face of the RADIO. The VAT is used to precisely orient (align) the radio in the correct direction. Select the hole that allows the most convenient viewing of the other end of link. The best viewing is achieved with your eye ~13 inches
(~33cm) from the VAT mirror. The radio is aimed at the point tangent to the top of the red indicator when all three indicators (green/red/green) are in a line with equal gaps between the indicators. Figure 3-9: View of VAT installed in the right hand side-mounting hole Tilt the radio up/down and right/left so that radio at the other end of the link is positioned at the top of the red indicator. See example below. 580-00505, rev 0.4 24 of 30 PRELIMINARY TM GE60 Installation Manual Radio at far end of link The alignment aids need to be in a straight line. Target, other radio, is placed at top of middle aid. Right Radio at far end of link Aiming Too low Wrong 5. Tighten the left/right adjustment bolt enough to prevent accidental movement of the radio. This is the bolt on the mount bracket, closest to the wall or pole. Verify the radio has not moved in left/right direction. As this bolt is tightened up/down movement of the radio may occur due to the seating the mounting bracken and radio yoke seat together. 6. Re-adjust the radio up/down, as necessary, due to the tightening of the mounting bracket. Tighten the lower bolts (below the up/down pivot bolts) on the radio yoke, being careful not disturb the up/down pointing of the radio. Once the lower bolts are tight, tighten the up/down pivot bolts. 7. Connect DC power to the radio, check that the Power LED is lit. If the Power LED is not lit, use voltmeter to verify correct voltage and polarity at radio. 8. Connect Tx & Rx fibers to the radio and check that the Fiber LED is lit. If the Fiber LED is not lit, swap the position of the Tx & Rx fibers and recheck.
(NOTE: In the event a fiber loopback cable is used on one of the radios in order to test the link, the Fiber LED will not light until the link is aligned and operating) 9. Repeat steps 1 through 8 on other side of link. 580-00505, rev 0.4 25 of 30 PRELIMINARY TM GE60 Installation Manual 10. Remove the plastic cover on the back of the radio that is secured with a cap bolt. Look to see that the Link Up LED is lit. This LED is lit when the two radios are aligned and passing data to one another. The link may still need be optimized via additional movement of the radio up and down and left and right; however, there is no need to proceed to the Fine Alignment or BER voltage steps detailed below unless this LED is lit. If desired, perform optional Fine Alignment (Section 3.9) on both sides of the link. 11. 12. Check the BER voltage. 3.3VDC indicates error free link. Note--alignment must be completed on both sides of the link and Link Up LED must be lit solid green before valid voltage readings can be made. Figure 3-10: Proper placement of voltmeter cables to check Pre-FEC BER Note: Black cable is connected to ground and red cable is connected to Pre-FEC BER pin 12. Securely tighten all mounting bolts. 580-00505, rev 0.4 26 of 30 PRELIMINARY TM 3.9 Fine Alignment -- Optional GE60 Installation Manual The fine alignment procedure uses Receive Signal Strength Indication (RSSI) voltage generated by the radios receiver. Since this voltage reacts to the power of the received signal, it is not influenced by the machining/manufacturing tolerances seen with mechanical parts. While procedure can yield an improvement of up to 2 dB in Link Budget when performed on both sides of the link, only those links with path lengths near the maximum length will see any benefits. 1. Attach voltmeter to the RSSI voltage pins. Note the RSSI voltage. The voltage may be fluctuating; in this case, note the maximum value seen. Figure 3-11: Proper placement of voltmeter cables to check RSSI Note: Black cable is connected to ground and red cable is connected to RSSI pin 2. Using care not to disturb the pointing of the radio, loosen the bolts tightened in steps 5 & 6 of the Visual Alignment procedure (Section 3.8) so that the radio may be tilted up/down and left/right. 580-00505, rev 0.4 27 of 30 PRELIMINARY TM GE60 Installation Manual Tilt the radio left and right until the maximum reading is achieved on the voltmeter. Tighten the left/right adjustment bolt to prevent movement in this axis. Tilt the radio up and down until the maximum reading is achieved on the voltmeter. Tighten the up/down adjustment bolts to prevent movement further movement. 3. 4. 580-00505, rev 0.4 28 of 30 PRELIMINARY TM GE60 Installation Manual 4 Operation The GE60 has been designed such that it requires no user configuration. During normal operation, the following conditions should exist at the radio:
1 2 3 4 The power LED should be litsolid green;
The fiber LED should be litsolid green;
The Link Up LED should be litsolid green; and The Pre-FEC BER voltage should be 3.3v, although occasional dips in voltage are acceptable. Figure 4-1: Link Up, Fiber and Pwr (Power) LEDs indicating link is up and operating The GE60 radio itself does not require periodic maintenance. However, each end of the link should be periodically inspected for visible damage or excessive accumulation of dirt. 580-00505, rev 0.4 29 of 30 PRELIMINARY TM 5 Troubleshooting GE60 Installation Manual Radio link troubleshooting process Yes Is the Pwr LED green?
No Yes Is the Fiber LED green?
No Yes Is the Supply voltage at the radio, with radio connected,
>+13.5v and
<+24.0v?
No Yes Yes Check receive direction of the radio at other end of the link. Check the fibers to the radio:
-Swap Tx & Rx fibers
-Network interface is on
-Verify fibers are good Check the polarity of the supply voltage. If polarity of the supply voltage is correct, replace radio. Check the power supply output. Verify the DC cable size
(AWG) is correct for the actual cable length. Is the Link Up LED green?
Does the local Network Equipment indicate good fiber connectivity?
No No Check the fibers to the radio:
-Swap Tx & Rx fibers
-Network interface is on
-Verify fibers are good Yes Is the RSSI voltage > 0.2v?
No Is the Pre-FEC BER voltage >
2.0v?
Yes No Yes Is the radio at the other end of the link operating and aligned?
No/unsure Check radio at other end of the link
(Fiber LED should be solid green) Re-align the radio for maximum RSSI voltage Check for possible interference by turning off radio at other end of link and verifying that the RSSI voltage has dropped below 0.2v Re-align the radio for maximum RSSI voltage Verify that maximum path length has not been exceeded (refer to Table 2-2) Verify that both radios are mounted in same polarization Verify that one radio is Low Band and one is High Band Re-align radio using VAT. Check radio at other end of the link. 580-00505, rev 0.4 30 of 30 PRELIMINARY
1 2 3 | User Manual 1 of 2 | Users Manual | 3.88 MiB | May 08 2005 |
making connections in a high-speed world The BridgeWave E60 product line Wireless Ethernet Links in the 60GHz Band Model AR60, FE60, GE60 &
AR60X, FE60X, GE60X Installation Manual P/N 580-00507 Revision 1 July 2005 1 of 46 TM GE60 Installation Manual Copyright Notice & Disclaimer Copyright 2004 BridgeWave Communications. All rights reserved. Printed in the USA No portion of this publication may be reproduced, copied, or distributed without the written consent of BridgeWave Communications. BridgeWave reserves the right to update or change the material in this publication at any time without notice. BridgeWave has made every effort to ensure that the information and the instructions contained in the publication are adequate and is not responsible for any errors or omissions due to typing, printing, or editing of this document. Purchasers of BridgeWave products should make their own evaluation to determine the suitability of each such product for their specific application. BridgeWaves obligations regarding the use or application of its products shall be limited to those commitments to the purchaser set forth in its Standard Terms and Conditions of Sale for a delivered product. This publication has been prepared for professional and properly trained personnel, and the customer assumes full responsibility when using the information herein. Statement of Warranty BridgeWave warrants each standard BridgeWave Product sold by it to be free of defects in material and workmanship under conditions of normal use for twelve (12) months from date of shipment thereof to Buyer. Repair or, at BridgeWaves option, replacement of defective parts shall be the sole and exclusive remedy under this limited warranty;
provided that BridgeWave may, as an alternative, elect to refund the purchase price amortized on a straight-line basis over a period of three (3) years from the date of shipment. All warranty replacement or repair of parts shall be limited to equipment malfunctions, which, in the sole opinion of BridgeWave, are due or traceable to defects in original materials or workmanship. In the event Buyer believes that Products do not conform to the limited warranty of this Section, Buyer shall pay for the shipping and insurance of such Product to BridgeWave. If BridgeWave determines in its sole opinion that such Products do not conform to the limited warranty, then BridgeWave shall pay for the shipping and insurance of repaired or replacement Products to Buyer. However, in the event that BridgeWave determines in its sole opinion that such Products conform to the limited warranty, Buyer shall pay for shipping and insurance of such Products back to Buyer. 580-00507, rev 1 2 of 46 TM GE60 Installation Manual All obligations of BridgeWave under this limited warranty shall cease in the event of abuse, accident, alteration, misuse or neglect of the Product. In-warranty repaired or replaced parts are warranted only for the remaining unexpired portion of the original warranty period applicable to the repaired or replaced parts. REASONABLE CARE MUST BE USED TO AVOID HAZARDS. BRIDGEWAVE EXPRESSLY DISCLAIMS RESPONSIBILITY FOR LOSS OR DAMAGE CAUSED BY USE OF ITS PRODUCTS OTHER THAN IN ACCORDANCE WITH PROPER OPERATING PROCEDURES. THE FOREGOING LIMITED WARRANTY FOR BRIDGEWAVE PRODUCTS IS EXPRESSLY IN LIEU OF, AND EXCLUDES ALL OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR PARTICULAR PURPOSE, USE OR APPLICATION, AND ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF BRIDGEWAVE, UNLESS SUCH OTHER WARRANTIES, OBLIGATIONS OR LIABILITIES ARE EXPRESSLY AGREED TO IN WRITING BY BRIDGEWAVE. Statements made by any person, including the representatives of BridgeWave, which are inconsistent or in conflict with the terms of these warranties shall not be binding upon BridgeWave unless expressly reduced to writing and approved by an officer of BridgeWave. Product Compatibility While every effort has been made to verify operation of this product with many different communications products and networks, BridgeWave makes no claim of compatibility between its products and other vendors equipment. It is assumed that users have thoroughly evaluated this products performance in the communications environment in which it will be used. Safety CAUTION, WARNING, and DANGER statements have been strategically placed in the text to alert personnel of possible hazards. These statements must be closely observed. The following general safety precautions must be observed during all phases of operation and service of the products covered in this manual. Failure to comply with these precautions or with specific warnings elsewhere in this manual willfully violates standards of design, manufacture, and intended use of the product. BridgeWave assumes no liability for the customers failure to comply with these requirements. 580-00507, rev 1 3 of 46 TM GE60 Installation Manual The BridgeWave 60GHz product line meets all applicable FCC safety requirements for radio equipment; however, it is best to avoid prolonged, unnecessary exposure to the front of the radio while it is operating. The exposure one would receive from aligning the radio is not harmful to humans. The outdoor equipment must be properly grounded to provide some protection against voltage surges and built-up static charges. In the event of a short circuit, grounding reduces the risk of electrical shock. For installations in the U.S.A., refer to Articles 810830 of the National Electrical Code, ANSI/NFPA No. 70, for information with respect to proper grounding and applicable lightning protection for DC cables. For installations in all other countries, implement protection in accordance with the safety standards and regulatory requirements of the country where the equipment is to be installed. Do not install or operate this equipment in the presence of flammable gases or fumes. Operation of any electrical instrument in such an environment constitutes a definite safety hazard. Do not install substitute parts or perform any unauthorized modification to the equipment. Changes or modifications not expressly approved by BridgeWave can void the users authority to operate the equipment. Regulatory Information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and,
(2) This device must accept any interference that may cause undesired operation. Equipment Precautions Water and Moisture - The E60 product line is designed to withstand moisture conditions typically encountered when installed outdoors. Power Sources - This product should only be operated with the type of power source provided by BridgeWave Communications Inc. 580-00507, rev 1 4 of 46 TM GE60 Installation Manual Table of Contents Section#
1 1.1 1.2 1.3 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 Copyright Notice & Disclaimer Statement of Warranty Product Compatibility Safety Regulatory Information & Equipment Precautions Table of Contents Introduction Purpose of Manual Prior Knowledge and Manual Conventions Contact Information & RMA Site Planning General Equipment Checklist Line of Sight Link Distance Antenna Location Cabling Grounding and Lightning Protection Environmental Simple Network Diagram Installation General Equipment Packing and Unpacking Equipment Inventory E60 Equipment Inventory E60X Installation Tools Radio Mount Installation E60 products Page #
2 2 3 3 4 5 6 6 6 7 8 8 8 8 9 12 12 13 14 15 16 16 156 17 18 19 20 24 27 29 33 Cable Installation 36 Antenna Alignment E60 Systems 39 Turning on E60X systems Test Cable 41 Operation of E60 products & configuration of network equipment 43 Configuring Network Equipment 44 44 Check port statistics Troubleshooting 45 3.1 3.2 3.3 3.3.1 3.4 3.5 3.5.1 Antenna Mount Installation E60X products 3.6 3.6.1 Antenna and Radio Installation E60X 3.7 3.8 3.8.1 3.9 Radio Installation E60 4.1 4.2 2 3 4 5 580-00507, rev 1 5 of 46 TM 1 Introduction 1.1 Purpose of Manual GE60 Installation Manual The information in this manual is directed to persons who must perform or coordinate the tasks associated with the process of installing wireless communication devices, and planning communication network applications. 1.2 Prior Knowledge This manual assumes the operator has at least basic experience with and an understanding of wireless technology and some familiarity with configuring and operating networking equipment. Preferably, the person installing this equipment fully understands the information covered in this manual prior to attempting these procedures. DANGER!
the given instruction. A DANGER statement will describe the potential hazard, its possible consequences, and the steps to perform to avoid personal injury. Indicates that personal injury can result if the user does not comply with Indicates that serious damage to the equipment can result if the user does WARNING!
not comply with the given instruction. A WARNING statement will describe the potential hazard, its possible consequences, and the steps to perform to avoid serious equipment damage. CAUTION!
Indicates that equipment damage, process failure, and/or loss of data can result if the user does not comply with the given instruction. A CAUTION statement will describe the potential hazard, its possible consequences, and the steps to perform to avoid equipment damage, process failure, and/or loss of data. NOTE: Provides supplementary information to emphasize a point or procedure, or provides a tip for easier operation. 580-00507, rev 1 6 of 46 TM 1.3 Contact Information GE60 Installation Manual Technical Assistance and Customer Service BridgeWave distributors are authorized local service providers and are responsible for immediate customer support. If problems are not resolved, contact BridgeWave Customer Service for assistance:
Santa Clara, CA USA 408.567.6906 Tel:
408.567.0775 Fax:
Email:
support@bridgewave.com Return Material Authorization (RMA) Should BridgeWave equipment have to be returned for repair or replacement, an RMA number must be obtained from BridgeWave or the local BridgeWave distributor. When returning equipment, be sure to write the RMA number on the outside of the shipping carton. 580-00507, rev 1 7 of 46 GE60 Installation Manual TM 2 Site Planning 2.1 General Before the start of an installation a survey should be conducted of the proposed area of the site(s). The survey personnel should be fully familiar with the details required to install the an E60 radio system. FE60 and FE60X radios transport Fast Ethernet over the wireless connection
(100Mbps full duplex) GE60 and GE60X radios transport Gigabit Ethernet over the wireless connection
(1000Mbps full duplex) AR60 and AR60X radios have an adaptive rate over the wireless connection, depending on the fade margin in the link the radio will transmit either Gigabit Ethernet or Fast Ethernet over the air 2.2 Equipment Checklist The survey team will need the following equipment:
Binoculars GPS Navigation Device Tape Measure Site Survey Report Form 2.3 Line of Sight (LOS) The E60 Wireless Ethernet link requires Line-of-Sight for proper operation. Fortunately, the links are relatively short and obstructions in the path can easily be identified. Binoculars can ease viewing in poor light conditions. The planning should include an investigation into future building plans that could block the LOS path, and other long-term incremental obstructions such as trees. Intermittent obstructions such as aircraft at a nearby airport should also be considered. The following table details the minimum clearance needed from obstacles near the path in order to ensure the radios will operate properly. 580-00507, rev 1 8 of 46 TM GE60 Installation Manual Path Length
(meters) Minimum Clearance
(meters) 250 500 750 1000 1500 2000 0.56 0.79 0.97 1.12 1.37 1.58 Table 2-1: Minimum Clearance at Link Midpoint for various Path Lengths 2.4 Link Distance Measurement of the link distance is important in estimating the link availability and calculating expected Receive Signal Level (RSL). This measurement can be performed using the Latitude and Longitude readings from a Global Positioning System (GPS) device, which is placed near the proposed locations of the antennas, or using a range finder device. Table 2-2 below lists the maximum link distance with respect to desired availability and ITU rain zone (ITU-R Recommendation PN.837). The map (Figure 2-1) following the chart shows where the rain zones fit across North America and Asia for various availabilities and most ITU rain zones. The availability for the AR systems is a combination of the FE and GE tables of the same type (FE60 and GE60 or FE60X and GE60X) depending on the current condition of the link. FE60 Distance Table
(V1545) Availability 99.9000%
99.9700%
99.9900%
99.9950%
99.9970%
99.9990%
A 1470 1410 1360 1310 1280 1220 B 1440 1370 1280 1220 1180 1100 C 1420 1340 1230 1170 1120 1030 Rain Zone D 1350 1300 1180 1100 1050 960 E 1400 1270 1140 1050 1010 910 F 1350 1220 1080 990 940 850 K 1280 1120 960 880 830 750 M 1140 980 840 770 730 660 N 980 820 710 660 630 580 580-00507, rev 1 9 of 46 TM GE60 Installation Manual FE60X Distance Table Rain Zone C 2300 2150 1960 1840 1760 1600 D 2170 2080 1870 1730 1640 1480 E 2250 2030 1800 1660 1570 1410 GE60 Distance Table Rain Zone C 960 910 850 800 770 720 D 920 890 810 760 730 670 E 940 870 790 740 700 640 GE60X Distance Table Rain Zone C 1760 1650 1520 1430 1370 1250 D 1670 1610 1450 1350 1280 1160 E 1730 1570 1400 1300 1230 1110 F 2170 1950 1690 1550 1460 1300 F 920 840 750 700 660 600 F 1670 1510 1320 1210 1140 1030 A 2380 2280 2180 2100 2050 1940 A 990 950 920 890 870 840 A 1820 1760 1680 1620 1580 1500 B 2340 2200 2050 1940 1870 1720 B 970 930 870 840 810 760 B 1790 1690 1580 1510 1450 1340 K 2040 1760 1490 1360 1270 1140 K 870 770 670 620 590 540 K 1580 1370 1170 1070 1010 910 M 1790 1520 1280 1170 1100 1000 M 790 680 590 550 520 480 M 1400 1190 1010 930 880 800 N 1520 1250 1070 990 940 870 N 710 580 510 480 460 420 N 1190 990 850 790 750 690
(V1620) Availability 99.9000%
99.9700%
99.9900%
99.9950%
99.9970%
99.9990%
(V1435) Availability 99.9000%
99.9700%
99.9900%
99.9950%
99.9970%
99.9990%
(V1620) Availability 99.9000%
99.9700%
99.9900%
99.9950%
99.9970%
99.9990%
Table 2-2: Maximum Link Distances (meters) for various Availabilities and Rain Zones 99.9000% availability equates to 526 minutes per year of outage due to heavy rains. 99.9700% availability equates to 158 minutes per year of outage due to heavy rains. 99.9900% availability equates to 53 minutes per year of outage due to heavy rains. 99.9950% availability equates to 26 minutes per year of outage due to heavy rains. 99.9970% availability equates to 15 minutes per year of outage due to heavy rains. 99.9990% availability equates to 5 minutes per year of outage due to heavy rains. 580-00507, rev 1 10 of 46 TM GE60 Installation Manual Figure 2-1: Rain Zone map for North America Figure 2-2: Rain Zone map for Asia 580-00507, rev 1 11 of 46 TM 2.5 Antenna Location GE60 Installation Manual The optimum location for the antennas must be determined. The ideal location should provide for ease of erecting and mounting the antenna, as well as unimpeded Line-Of-
Site (LOS) to the other site. The following factors should be taken into account:
Type of mountingwall or pole Location where the fiber and DC power wiring will enter/exit the building Length of cable runs Grounding connection points Obstructions Accessibility 2.6 Cabling The installation site should be inspected to determine the run paths for the fiber cable and power cable from the radio equipment to the termination point. Locations for roof penetration should be identified. The routing and securing of all cables should conform to all applicable codes and requirements. Depending on the likelihood of damage due to foot traffic or equipment movement, cabling conduit may be required. The maximum cable run length as specified for the equipment being installed must not be exceeded. The radio requires an LC type connectors on a pair of simplex multi-mode fibers to properly connect to the radio and the users network equipment. Single-mode fiber is not a current option supported by the radio. The network equipment end of the fibers should be terminated with connectors that match the network equipment fiber interface. Fiber Cable Length Up to 270 meters Up to 500 meters Cable Type 62.5/125 m 50/125 m Table 2-3: Fiber Cable Types All radios in the E60 product line include a 100-240 VAC power adaptor suitable for indoor operation that converts the AC voltage from the standard electrical outlet in the wall to DC voltage. Our radio requires a minimum of 15.0 VDC (24.0 VDC maximum) up the power cable to the radio to function properly. When planning the cable run from the indoor mounted AC power adaptor to the radio unit, it is critical to use the cable gauge (AWG) indicated below to ensure adequate voltage at the radio. The electrical cable that is used outside the building must be outdoor rated (i.e., weather-protected) providing a single pair of wires necessary to power the equipment. The required DC power cable is 12 gauge, 2 wire (i.e., 12/2) rated for outdoor use. 580-00507, rev 1 12 of 46 TM DC Cable Length Up to 250 meters GE60 Installation Manual Minimum Cable Size Outside Diameter of DC Cable Jacket (min-max)*
0.17 0.45 inches
(4.3 11.9 mm) Table 2-4: Minimum DC Cable Size Conductor size 12 AWG
(4mm2)
*Note: Specification is for the outdoor weather-protected portion of the DC cable entering the radio enclosure. The indoor portion of the DC cable must comply with local building and/or electrical codes in your area. Figure 2-3 (left) details a standard 12-gauge wire that has been fitted with the power connectors (provided) for the radios internal power supply necessary to mate with the provided power cord. A standard crimping/splicing tool (not provided) is required to terminate the power connectors onto the 12-gauge cable required for use with the E60 products. Figure 2-3: 12-gauge DC power cable with crimp connectors 2.7 Grounding & Lightning Protection WARNING!
Proper grounding of the outdoor equipment reduces electromagnetic interference, provides lightning protection, and protects against electrical discharge. The source and connection points for the building-to-earth ground in the vicinity of the antenna location should be determined. It is recommended to integrate the radio ground into the building ground utilizing the pole mount hardware. For wall or ungrounded pole mounts connect a grounding wire to the grounding point on the radio. Select the size of the ground wire based on the National Electrical Code. 580-00507, rev 1 13 of 46 TM GE60 Installation Manual In addition to grounding the equipment, BridgeWave strongly recommends, and local building codes may require, the DC electrical cable to be protected from lightning strikes. You may use a Polyphaser surge suppressor, model # IS-PSP-24 (or equivalent model from another manufacturer). The surge suppressor must be installed at the point where the DC electrical cable exits/enters the building. The Polyphaser device is available from the following companies:
Hutton Communications 877-648-8866 TESSCO Technologies 800-472-7373 888-946-6266 Winncom Technologies Corp. www.huttoncom.com www.tessco.com www.winncom.com 2.8 Environmental The structure to which the equipment will be mounted should be adequate to bear all wind and other weather conditions. The environmental conditions at the location must conform to the operating environment specified for the equipment. 580-00507, rev 1 14 of 46 TM GE60 Installation Manual 2.9 Simple Network Diagram Following is a diagram detailing the equipment and cabling found on a typical installation of BridgeWaves 60GHz radio equipment. High-Band Radio Vertical Polarization Low -Band Radio Vertical Polarization Path betw een radios Gig-E Sw itch or Router Gig-E Sw itch or Router Fiber Optic Cable Fiber Optic Cable Indoor Pow er Supply Surge Suppressor DC Pow er Cable DC Pow er Cable Indoor Pow er Supply LAN/
WAN Surge Suppressor LAN/
WAN Note: The ports on all switches or routers must be configured for: 1000Mbps, full-duplex and auto-negotiation disabled. 580-00507, rev 1 15 of 46
1 2 3 | User Manual 2 of 2 | Users Manual | 2.22 MiB | May 08 2005 |
TM 3 Installation of E60 products GE60 Installation Manual 3.1 General It is recommended that installation personnel read this section in its entirety prior to installing the BridgeWave System. During a particular phase of installation, the user may refer directly to the applicable subsection. The Installation section is comprised of seven subsections covering the procedures and guidelines for installing the BridgeWave Radio System. Subsections 3 through 3.4 contain information necessary to prepare for the equipment installation. Subsection 3.5 through 3.7 covers equipment installation procedures. Subsection 3.8 and 3.9 contains information necessary for aligning the antennas. 3.2 Equipment Packing & Unpacking The radio system equipment will arrive in two boxesone box for the low band radio and one box for the high band radio. Locate the correct box (low band or high band) before beginning installation by checking the label on the outside of the box or on the radio itself. It is recommended that the shipping cartons and packing materials be retained in the event that it is necessary to return any equipment. Note: Unpacked radios can be identified by the color of their labels. The blue color label indicates a high band radio and the red color label indicates a low band radio. See Figure 3-5 for further details. 580-00507, rev 1 16 of 46 TM GE60 Installation Manual 3.3 Equipment Inventory for E60 products Each carton is accompanied by a packing list. Verify the contents of the carton against the packing list. Following are inventory lists for a typical system. Qty Description 2 ea. AR60, FE60 orGE60 Radios (1 Low band & 1 High band) 2 ea. Wall Mount Kits 2 ea. AC-DC power adapters & power cords 2 ea. Pole Mount Kits (required only when mounting the radio onto a pole) 2 ea. Copper grounding cables 1 ea. Visual alignment tool or VAT (1 provided per pair of radios) 1 ea. CD-ROM containing Installation Manual (1 provided per pair of radios) 2 ea. Power cables with DC power connectors attached for use with outdoor radio 8 ea. DC power connectors E60 Wall Mount Kit Parts List Item Description 1 2 3 4 5 6 Mount Bracket Radio Yoke Teflon Shim Split Lock Washer Flat Washer
-16 x bolts E60 Pole Mount Kit Parts List Item Description Pole Clamp
-16x9in Threaded Rod 1 2 3 Split Lock Washer 4 5 6 Flat Washer
-16 Hex Nut
-16 x bolts Qty. 1 1 1 4 4 4 Qty. 4 4 14 (2 spare) 14 (2 spare) 13 (1 spare) 6 (2 spare) 580-00507, rev 1 17 of 46 TM GE60 Installation Manual Tampering with seals will void the warranty. CAUTION!
Notice the warranty stickers on the inner (metal) cover of the radio. The radio is sealed at the factory. There is no need to open this cover in the field. Tampering with these seals will void the warranty. 3.3.1 Equipment Inventory for E60X products Each carton is accompanied by a packing list. Verify the contents of the carton against the packing list. Following are inventory lists for a typical system. Qty Description 2 ea. GE60X Radios (1 Low band & 1 High band) 2 ea. AC-DC power adapters & power cords 2 ea. Pole Mount Kits 1 ea. CD-ROM containing Installation Manual (1 provided per pair of radios) 2 ea. Power cables with DC power connectors attached for use with outdoor radio 8 ea. DC power connectors 2 ea Antenna and mount kits GE60X Antenna and Mount Kit Parts List Item Description Qty. 1 1 1 2 Antenna Lower Pole mount assembly 3 Upper Pole mount 4 5 6 7 8 assembly Antenna mounting plate 3/8 bolts 3/8 lock washers 3/8 flat washer 3/8 nylon washer 1 1 2 2 2 2 Tampering with seals will void the warranty. CAUTION!
Notice the warranty stickers on the inner (metal) cover of the radio. The radio is sealed at the factory. There is no need to open this cover in the field. Tampering with these seals will void the warranty. Figure 3-1 580-00507, rev 1 18 of 46 TM 3.4 Installation Tools GE60 Installation Manual The following tools, not provided by BridgeWave, should be used for installing the radio:
Screwdriver, slotted 0.1 inch (2.5mm) wide Open-end wrench 11/32 (9mm) Open-end wrench 9/16 (14mm), 2 ea. Open-end wrench inch (13mm) Ratchet with 6 inch (15cm) extension and 9/16 inch (14mm) deep socket Wire stripper/cutter/crimp tool (10-16 gauge) Electrical tape Fish tape for pulling cable Cable tie wraps Hand-held DVM (digital voltmeter) with standard banana plug receptacles 580-00507, rev 1 19 of 46 TM GE60 Installation Manual 3.5 Radio Mount Installation E60 products Wall Mounting 1. 2. Install 4 mounting bolts in the wall at the desired location using the template provided (see Figure 3-4 below). The bolts (normally -16) should extend 0.8 to 3.0 inches (2cm to 7.5cm) from the wall and be strong enough to secure the radio to the wall under foreseeable environmental conditions. The environmental conditions may include, but not limited to, wind, rain, ice, etc. Depending on the wall material the mount is being attached to, a different size bolt may be appropriate. In this case, bolts up to inch in diameter may be used. Secure the mount to the bolts using the appropriate sized nuts, lock washers, and flat washers for the bolts used to mount the bracket. Figure 3-1: Mount in Wall Mount Configuration 580-00507, rev 1 20 of 46 TM GE60 Installation Manual 3. Attach the radio yoke to the mount, with Teflon shim in-between, using 2 each of the supplied -16 x bolts, lock washers, and flat washers. Tighten the bolts just enough that the yoke can move back and forth without binding. 3/8-16x3/4 Bolts 3/8 Lock Washer 3/8 Flat Washer Mounting Bracket Teflon Shim Radio Yoke Pole Mounting The pole mount kit can be used to secure the mount to a pole with diameters between 2.0 to 4.5 inches (50 to 115 mm). 1. Attach two of the pole clamps to the mounting bracket using 4 each -16 x bolts, lock washers, and flat washers. Attach the threaded rods to the pole clamps using 8 -16 nuts and 4 each lock washers and flat washers. Refer to Figure 3-3. Note: The nuts on the inside of the pole clamps do not require any washers since they are only holding the threaded rods in place and to not bare any load. Secure the mount to the pole using two pole clamps and 4 each -16 nuts, lock washers, and flat washers. 2. 3. Attach the radio yoke as described above. 580-00507, rev 1 21 of 46 TM GE60 Installation Manual Figure 3-2: Mount with Radio Yoke in Pole Mount Configuration Figure 3-3: Side view of mount in Pole Mount Configuration 580-00507, rev 1 22 of 46 TM GE60 Installation Manual 6.25 inches
(15.9 cm) 3.13 inches
(8.0 cm) Figure 3-4: Template to drill holes on the wall for E60 radios Wall Mount 580-00507, rev 1 23 of 46 TM GE60 Installation Manual 3.5.1 Antenna Mount Installation E60X products WARNING!
1. Read these instructions before beginning installation. Caution should be used. Qualified persons experienced with antenna assembly and installation are required for installation. 2. BridgeWave Communications Inc. disclaims any responsibility or liability for damage or injury resulting from incorrect or unsafe installation practices. 3. The antenna has been formed to a very close tolerance parabolic shape. Careful handling and assembly is required to avoid denting the reflector, which would degrade antenna performance. 1. Attach the upper pole mount. Confirm that the Mount is centered as shown. Tighten bolts Securely Figure 3-2.1 580-00507, rev 1 24 of 46 TM GE60 Installation Manual 2. Attach the lower pole mount as shown. Hardware: Flat washer, bushing
(inside eye), flat washer, lock washer, bolt. Confirm that the Mount is centered as shown. Tighten bolts securely Figure 3-3.1 and 3-4.1 580-00507, rev 1 25 of 46 TM GE60 Installation Manual 3. Completed installation of pole mount with right hand offset for the antenna. Note the position of the elevation adjust hex nut. Figure 3-5.1 4. Optional left hand antenna offset mount preparation.
- Remove bolts
rotate the antenna mounting plate 180 replace bolts tighten bolts securely Figure 3-6.1 Note the new position of the elevation adjust hex nut. 580-00507, rev 1 26 of 46 TM GE60 Installation Manual 3.6 Radio Installation 1. Place the radio in the yokethe two up/down pivot bolts should rest in the Us cut in the yoke. Note that when the radio comes from the factory, the mounting plates are in the vertical polarization position, that is, the diamond marking on the radio (see insert below) on the front of the radio housing is to the right when viewed from the front. For horizontal polarization, the mounting plates should be moved so that the diamond is at the top when viewed from the front. Figure 3-5: Polarization diamond orientations: horizontal (left) and vertical (right) Note: The blue color label indicates a high band radio and the red color label indicates a low band radio See Figure 3-5 for further explanation and visual image of horizontal vs. vertical polarization. CAUTION!
It is critically important during installation to ensure the radios on each side of the link are in the same polarization (horizontal-horizontal or vertical-
vertical). A link that has a radio on one side of the link set in the horizontal polarization and the other side of the link set in the vertical polarization will not operate properly. Further, it is also critically important that a high-band radio is paired with a low-band radio to ensure the system will operate properly. Prior to installation check each radio to verify one is a high-band and the other is a low-band version. The label on the radio will indicate the band (blue for high or red for low). 580-00507, rev 1 27 of 46 TM GE60 Installation Manual 2. Once the radio has been placed in the yoke mount, insert the bolt in the lower portion of the yoke to secure the radio to the yoke. Tighten both the pivot bolts and the lower yoke bolts enough such that the radio is secured in the mount but is still able to be moved back and forth easily. Figure 3-6: Detail of Radio in Yoke Mount and the Up/Down Pivot Bolt. Note that the lower bolt required to secure the radio to the mount has not yet been inserted in the picture above. Note: Use both flat washer & split lock washer on lower yoke bolt 580-00507, rev 1 28 of 46 TM GE60 Installation Manual 3.6.1 Antenna and Radio installation 5. Install Antenna Slip antenna over pivot pin, ensuring that the elevation adjust pin is engaged with slot in adaptor plate. Secure the antenna with two (2) x 3/8-16 bolts, lock washer, flat washer and nylon washers attach antenna to the alignment plate. Figure 3-7.1 Note that when the radios come from the factory, they are mounted on the back of the antenna in the vertical polarization position, that is, the diamond marking (see insert below) on the front of the radio housing is to the right when viewed from the front of the radio. For horizontal polarization, the radio needs to be removed from the antenna and rotated so the diamond is at the top when viewed from the front. 580-00507, rev 1 29 of 46 TM GE60 Installation Manual Figure 3-8.1: Polarization diamond orientations: horizontal (right) and vertical (left) Note: The blue color label indicates a high band radio and the red color label indicates a low band radio CAUTION!
It is critically important during installation to ensure the radios on each side of the link are in the same polarization (horizontal-horizontal or vertical-
vertical). A link that has a radio on one side of the link set in the horizontal polarization and the other side of the link set in the vertical polarization will not operate properly. Further, it is also critically important that a high-band radio is paired with a low-band radio to ensure the system will operate properly. Prior to installation check each radio to verify one is a high-band and the other is a low-band version. The label on the radio will indicate the band (blue for high or red for low). 6. Verify that the four (4) captive 3/8-16 bolts with lock and flat washer are in place. A inch open-end wrench is required to tighten them. It is important that all four screws are tightened evenly (hand tight, 1 to 2 turns each and finally until the lock washer is flattened) Figure 3-9.1 Captive radio bolt detail 580-00507, rev 1 30 of 46 TM GE60 Installation Manual 7. Attach the radio to the back of the antenna and tighten the four (4) bolts. See 6. for details. Figure 3-10.1 Attaching the radio to the back of the antenna 8.Adjust azimuth (Side to Side) 1. Loosen the 4 Azimuth lock bolts 2. Adjust eyebolt length using a 9/16 open-end wrench to required location 580-00507, rev 1 31 of 46 Figure 3-11.1 Azimuth alignment detail 3. Secure the 4 Azimuth lock bolts
(tighten until lock washers are flatend) TM GE60 Installation Manual Caution! It is very important that the azimuth bolts are tightened before any elevation adjustment is done. The very narrow beamwidth of this antenna (0.6) makes it necessary to completely tighten the bolts of the azimuth adjustment while adjusting the elevation and vice versa. 8. Adjust elevation (up - down) 2. Rotate Elevation adjust hex nut as required to set correct elevation. 3. Tighten all bolts after the elevation is set. 1. Loosen (2) antenna mounting bolts Figure 3-12.1 Elevation adjustment 580-00507, rev 1 32 of 46 TM GE60 Installation Manual 3.7 Cable Installation 1. Fiber Cabling Install a duplex multi-mode fiber from the radio to the network termination equipment (switch or router with 1000Base-SX port). The cable should be looped around the inside of the enclosure to provide strain-relief. Do not connect the fibers to the radios fiber ports at this time. The connectors on the radio end of the fiber require simplex LC connectors; the connectors on the switch/router end should mate to the network equipment. Note: The simplex LC connectors for the radio need to be inserted individually through the slip-fit connectors on the radio, as there is not sufficient room for both to fit through at the same time. 2. Connect fibers at the network equipment. It is important not to connect the fibers to the radio until after aligning the radio as the radio performs an automatic calibration once the fiber is inserted into the radio and this calibration will not operate properly if the radio is not properly aligned. Power Cabling Select indoor location, with easy cable routing to the radio, for the AC power adaptor. Normally it is convenient, but not required, to place the adaptor near the network termination equipment. Ensure the DC wire used is 12-gauge type and no longer than 250 meters. 2. 3. Connect the provided DC Connectors onto the 12-guage wire using a splicing/crimping tool. It may be necessary to trim a few strands from the ends of thicker stranded cables to more easily fit the crimp connectors. Install the DC power cable and attach to the AC adaptor using the supplied crimp connectors. Do not connect the power jack to the radio at this time. IMPORTANT: Be sure to first connect the DC power crimp connectors before inserting the power plug into the power jack in the radio. Minor electrical sparks may be noticed if the sequence above is not followed; however, these sparks will not cause any harm to the radio or people. 1. 4. 5. 580-00507, rev 1 33 of 46 TM GE60 Installation Manual Figure 3-7: Front view of fiber and power cable installed on a vertically polarized E60 unit. Figure 3-8: Inside view of fiber and power cable connected E60 or E60X unit Note: The fiber cable is inserted through the straight through fitting on the left and the power cable is inserted through the fitting on the right. Both the cables have been looped around the inside of the enclosure to minimize tension on the cables when connected to the radio and to maintain proper bend-radius of the fiber cable. 580-00507, rev 1 34 of 46 TM GE60 Installation Manual Ground Cabling The preferred method for grounding the radio unit is to ground the mast (or wall-mount bracket) to a ground source, since this provides the largest grounding surface contact possible. If this is not possible, then use the following procedure:
1. Attach the lug of the copper ground cable provided with the radio to one of the two
#8 holes at the bottom of the radio using a #8-32 bolt, #8 lock washer and #8 flat washers. 2. Connect other end of the ground cable to a nearby ground location. 580-00507, rev 1 35 of 46 TM GE60 Installation Manual 3.8 Antenna Alignment E60 systems 1. Place the radio in the mounting bracket, make sure both bolts slide to the bottom of the cutouts. 2. Tighten mounting bolts just enough to allow radio to pivot up/down and right/left with minimal effort. DO NOT CONNECT EITHER THE DC OR FIBER CABLES TO THE RADIO AT THIS POINT! Tilt the radio so that it is roughly points towards the other end of the link. 3. Insert the Visual Alignment Tool (VAT) into one of the 4 holes in the front (antenna) face of the radio. The VAT is used to precisely orient (align) the radio in the correct direction. Select the hole that allows the most convenient viewing of the other end of the link. The best viewing is achieved with your eye ~13 inches (~33cm) from the VAT mirror. Move the radio such that it is aimed at the point tangent to the top of the red indicator when all three indicators (green/red/green) are in a line with equal gaps between the indicators. Figure 3-9: View of VAT installed in the left hand side-mounting hole 4. Tilt the radio up/down and right/left so that the radio at the other end of the link is positioned at the top of the red indicator. See example on the next page. 580-00507, rev 1 36 of 46 TM GE60 Installation Manual R a d io a t fa r e n d o f lin k T h e a lig n m e n t a id s n e e d to b e in a s tra ig h t lin e . T a rg e t, o th e r ra d io , is p la ce d a t to p o f m id d le a id . R ig h t Radio at far end of link Aiming Too low Wrong 5. Ensure fiber cables are still disconnected!
6. Connect DC power to the radio. 7. Verify that the Power LED is lit. If the Power LED is not lit, use voltmeter to verify correct voltage and polarity at radio. To reverse the power polarity, unplug the power jack and swap the crimp connectors for the two conductors. 8. Repeat steps 1 through 7 on other side of the link. 9. Verify Link Up LEDs are lit on both radios. 10. Slightly rotate each radio up/down and left/right to find the maximum RSL voltage reading. [If it was not possible to use the VAT to visually align the radios, then the radios must be rotated at least ten degrees on each side of the visually-perceived alignment center to ensure that the true maximum RSL voltage is found; note that the width of the center beam is only 1.4 degrees and the first side-lobe beam is only 2.5 degrees off from center.] Set the radio in the position that results in the highest RSL voltage reading. See Section 3.9 to determine the proper use of the supplied test cable in order to read the RSL voltage. Note: Verify that the RSL voltage falls within the expected range based on the graph in Appendix A. 580-00507, rev 1 37 of 46 TM GE60 Installation Manual 11. Begin to tighten the mounting bolts. It is important to tighten the bolts in the following order. First start with the bolts that control the left/right movement of the radio. These are the bolts on the yoke portion of the mount behind the radio. Start by tightening the bolt closest to the pole or wall. Once this is tightened, move to the bolt directly in front of the bolt you just tightened and slowly tighten this bolt. While tightening the bolts be careful that the radio does not move during the process. As these bolts are tightened up/down movement of the radio may occur due to the seating of the mounting bracket and radio yoke. Check the RSL voltage reading to ensure it is still at its maximum level, and adjust vertical tilt if required. Next, tighten the bolts that allow the up/down movement of the radio. First tighten the lower bolts on both sides of the yoke bracket. Once the lower bolts are tightened on both sides of the radio, tighten the upper bolts. 12. Connect the fiber cable to one of the radios at a time. The fibers should already be connected to active network equipment. 13. Verify the Fiber LEDs on each radio are lit solid. Note: The fiber integrity indication on the network equipment could show up or down independent of the link status. Ones the radio link is up and network equipment connected on both sides of the link the network equipment will indicate fiber integrity. 14. Once the fiber is connected to the radio, the radio will begin an internal link calibration. During this time the Link Up LED will blink for approximately 30 seconds. 15. Wait until the Link Up LED will be lit solid on both radios. 16. Verify the Link Quality voltage is 3.3V (i.e., error free). Repeat steps 10-12 for the second radio. Note: When a radio is power cycled, it will re-execute the calibration process. After this time, the link should be functioning. This automatic calibration process is also activated if the link is down for more than 50 seconds. Also, if using a loop back fiber connector at one end of the link for test purposes, note that the radio connected to actual network equipment must complete auto calibration prior to connecting the loop back cable at the other end. 17. Remove the VAT from the radio, replace the back plastic cover and use a wrench to tighten the back cover nut to the point where the back cover stops (i.e., when it hits the metal ring on the back metal plate). The installation is now complete. 580-00507, rev 1 38 of 46 TM GE60 Installation Manual 3.8.1 Turning on an E60X system 1. Finish the installation as described in Chapter 3.6 and 3.7 2. Ensure fiber cables are still disconnected!
3. Connect DC power to the radio. 4. Verify that the Power LED is lit. If the Power LED is not lit, use voltmeter to verify correct voltage and polarity at radio. To reverse the power polarity, unplug the power jack and swap the crimp connectors for the two conductors. 5. Repeat steps 1 through 4 on other side of the link. 6. Verify Link Up LEDs are lit on both radios. 7. Slightly rotate each antenna up/down and left/right to find the maximum RSL voltage reading. To ensure that the antennas are not aligned on a side-lobe, they must be rotated at least ten degrees on each side of the visually-perceived alignment center to ensure that the true maximum RSL voltage is found; note that the width of the center beam is only 0.6 degrees and the first side-lobe beam is only 1.5 degrees off from center. Set the antenna in the position that results in the highest RSL voltage reading. See Section 3.9 to determine the proper use of the supplied test cable in order to read the RSL voltage. Note: Verify that the RSL voltage falls within the expected range based on the graph in Appendix A. 8. Ensure all bolts are tightened securely and the RSL voltage remains unchanged during tightening. Keep in mind that it is very important that the azimuth bolts are tightened before any adjustment on the elevation is done. The very narrow beamwidth of this antenna (0.6) makes it necessary to completely tighten the bolts of the azimuth adjustment while adjusting the elevation and vice versa. 9. Connect the fiber cable to one of the radios at a time. The fibers should already be connected to active network equipment. 10. Verify the Fiber LEDs on each radio are illuminated solid. Note: The fiber integrity indication on the network equipment could show up or down independent of the link status. Once the radio link is up and network equipment connected on both sides of the link, the network equipment will indicate fiber integrity. 580-00507, rev 1 39 of 46 TM GE60 Installation Manual 11. Once the fiber is connected to the radio, the radio will begin an internal link calibration. During this time the Link Up LED will blink for approximately 30 seconds. 12. Wait until the Link Up LED is lit solid on both radios. 13. Verify the Link Quality voltage is 3.3V (i.e., error free). Repeat steps 10-12 for the second radio. Note: When a radio is power cycled and its fiber cable disconnected, it will re-
execute the calibration process. After this time, the link should be functioning. This automatic calibration process is also activated if the link is down for more than 5 minutes. Also, if using a loop back fiber connector at one end of the link for test purposes, note that the radio connected to actual network equipment must complete auto calibration prior to connecting the loop back cable at the other end. 14. Remove the test cable from the radio, replace the rear plastic cover and use a wrench to tighten the back cover nut to the point where the back cover stops (i.e., when it hits the metal ring on the back metal plate). The installation is now complete. 580-00507, rev 1 40 of 46 TM GE60 Installation Manual Auto Calibration States Description Unit will be in alignment mode, there will be no automatic calibration event started until the fiber is connected The radio will perform a single calibration scan and will then go into normal operation mode, regardless of the results of the scan. (Link up or down status has no influence on the scan) Disconnecting and reconnecting the fiber cables will not cause a recalibration. A recalibration will only happen if the link is down for more then 50 seconds. Power cycling the radio will start the auto calibration routine if the fiber cables are connected. If the fiber cables are disconnected the radio will go back into alignment mode. State Unit powered up no fiber connected Unit powered up and fiber cable connected Normal operation mode Forced Recalibration 3.9 Test Cable The alignment procedure is optimized through the use of the provided test cable. This test cable is designed for use with a digital voltmeter (not provided) to read the Link Quality and Receive Signal Level (RSL) voltage generated by the radios receiver. 1. To read the RSL value of the radio, insert GND (ground) and RSL banana plugs into the voltmeter. Note the RSL voltage. The voltage may be fluctuating; in this case, note the maximum value seen. 580-00507, rev 1 41 of 46 TM GE60 Installation Manual Figure 3-10: Top view of test cable provided to check Link Quality & Receive Signal level 2. To read the Link Quality value of the radio, insert GND (ground) and QUAL banana plugs into the voltmeter. Note the Link Quality voltage. After the radios have performed an auto calibration the quality voltage should read 3.3v if the link is aligned on the main antenna beam and there are no obstructions (i.e., trees, buildings, etc) in the path, the link distance is within the operating parameters of the radio (see Section 2.4 above), and it is not raining heavily. 580-00507, rev 1 42 of 46 TM GE60 Installation Manual 4 Operation of E60, E60X radios & configuration of network equipment The E60 product line has been designed such that it requires no user configuration. During normal operation, the following conditions should exist at the radio:
1 2 3 4 The power LED should be litsolid green;
The fiber LED should be litsolid green;
The Link Up LED should be litsolid green; and The Link Quality BER voltage should be 3.3v, although dips in voltage are acceptable during periods of precipitation. Figure 4-1: Link Up, Fiber and Pwr (Power) LEDs indicating link is up and operating The E60(X) radios them self do not require periodic maintenance. However, each end of the link should be periodically inspected for visible damage or excessive accumulation of dirt on the antennas radome (the front cover of the radio). 580-00507, rev 1 43 of 46 TM GE60 Installation Manual 4.1 Configuring Network Equipment The networking equipment that is connected to an E60 product should first be checked to ensure it operates properly over a wired connection. Once this has been confirmed this will save troubleshooting steps after the radio is installed and connected to the network equipment. We strongly recommend the network equipment on both sides of the link be configured as follows:
1000Mbps full-duplex
No port auto negotiation and no flow control Port configured not to enter error-disable state due to link up/down transitions (since these may occur during periods of heavy rain) 4.2 Check port statistics on the network equipment In the event the network equipment connected to the GE60 offers the capability below, we recommend you verify the following on the network equipment:
Link integrity
There are no receive errors on the link Network traffic is flowing in both directions. 580-00507, rev 1 44 of 46 TM GE60 Installation Manual 5 Troubleshooting The following table provides a summary of possible problems you might encounter while installing a BridgeWave GE60 link, along with possible causes and their solutions. Problem No power to radio Possible Cause Wrong polarity of supply voltage The supply voltage measured at the radio (when connected) is below 15Vdc Fiber light lit at radio but not on network equipment Radio link is down and/or fiber not connected between remote radio and network equipment. TX and RX fiber swapped Error in the configuration of the Networking equipment One or both of the fibers have been damaged Can not establish the wireless link Units are not properly aligned Obstacle in link Resolution Use a DMV to determine the polarity and voltage on the DC cable. (See page12) The cable run is too long or the cable gauge is too small. Shorten the length of the cable or use larger gauge cable. (See page 12) This is normal behavior. Complete end-to-end installation and re-check. Try swapping the TX and RX fibers at one/both ends of the connection Verify the configuration of the network equipment:
Port is turned on and set to 1000Mbps Full Duplex and auto negotiation is turned off. Use a loopback connector at the radio to verify the radio is OK, repeat at the networking equipment. Visually inspect the fiber cable. Use the VAT device as described in the manual. (See page 27 28) Verify the Line of Sight conditions and check for required clearance (See page 8 for clearance distances). 580-00507, rev 1 45 of 46 TM GE60 Installation Manual RSL voltage lower then expected Incorrect calculation of link distance Antennas aligned on side lobes Antennas set to different polarizations Installed two high or low band radios in one link Link exceeds maximum specified range Fibers are not connected Antennas are not aligned for maximum RSL Auto calibration not completed Interference Low link quality voltage Verify that the calculation tool used and the GPS used both use the same annotation system
(degree hours minutes seconds or degree with a decimal value) Use Visual Alignment Tool to verify direction of antennas. Verify that both radios are set to the same polarization. (see page 22) Verify that one end of the link is high and the other end is a low band radio (see page 22) Verify that maximum path length has not been exceeded Connect fiber and let radio perform its auto calibration routine (see page 29) Use the Visual Alignment Tool to verify antenna alignment. Power cycle units to force auto calibration cycles. (see page 29) Check for possible interference by turning off the radio at the other end of the link and verify the RSL voltage on the local site drops below 0.2V 580-00507, rev 1 46 of 46
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2005-08-05 | 58100 ~ 62900 | DXX - Part 15 Low Power Communication Device Transmitter | Class II permissive change or modification of presently authorized equipment |
2 | 2005-06-29 | 58100 ~ 62900 | DXX - Part 15 Low Power Communication Device Transmitter | |
3 | 2004-03-31 | 58100 ~ 62900 | DXX - Part 15 Low Power Communication Device Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 3 | Effective |
2005-08-05
|
||||
1 2 3 |
2005-06-29
|
|||||
1 2 3 |
2004-03-31
|
|||||
1 2 3 | Applicant's complete, legal business name |
BridgeWave Communications, Inc.
|
||||
1 2 3 | FCC Registration Number (FRN) |
0008264004
|
||||
1 2 3 | Physical Address |
3350 Thomas Road
|
||||
1 2 3 |
Santa Clara, California 95054
|
|||||
1 2 3 |
United States
|
|||||
app s | TCB Information | |||||
1 2 3 | TCB Application Email Address |
m******@ccsemc.com
|
||||
1 2 3 |
m******@ccsemc.com
|
|||||
1 2 3 | TCB Scope |
A2: Low Power Transmitters (except Spread Spectrum) and radar detectors operating above 1 GHz
|
||||
app s | FCC ID | |||||
1 2 3 | Grantee Code |
RWM
|
||||
1 2 3 | Equipment Product Code |
GE60
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 3 | Name |
C****** L****
|
||||
1 2 3 | Title |
Sr. Manager, Product Verification
|
||||
1 2 3 | Telephone Number |
408 5********
|
||||
1 2 3 | Fax Number |
408 5********
|
||||
1 2 3 |
c******@bridgewave.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 3 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
1 2 3 | Yes | |||||
1 2 3 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 3 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 3 | Equipment Class | DXX - Part 15 Low Power Communication Device Transmitter | ||||
1 2 3 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Microwave Link | ||||
1 2 3 | Microwave Link, High & Low Band | |||||
1 2 3 | Wireless Gigabit Ethernet Link | |||||
1 2 3 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 3 | Modular Equipment Type | Does not apply | ||||
1 2 3 | Purpose / Application is for | Class II permissive change or modification of presently authorized equipment | ||||
1 2 3 | Original Equipment | |||||
1 2 3 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 2 3 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 3 | Grant Comments | Class II permissive change filing. Ouput power listed is conducted. Only integral cassegrain antenna(s) as documented in the certification filings can be used. | ||||
1 2 3 | Class II permissive change filing. Ouput power listed is conducted. Only integral cassegrain antenna as documented in this Class II filing and original certification filing can be used. | |||||
1 2 3 | Ouput power listed is conducted. Only integral cassegrain antenna as documented in this filing can be used. | |||||
1 2 3 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 3 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 3 | Firm Name |
Compliance Certification Services Inc
|
||||
1 2 3 | Name |
S**** C******
|
||||
1 2 3 | Telephone Number |
408-4******** Extension:
|
||||
1 2 3 |
408-4******** Extension:
|
|||||
1 2 3 | Fax Number |
408-4********
|
||||
1 2 3 |
s******@ccemc.com
|
|||||
1 2 3 |
s******@ccsemc.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 58100.00000000 | 62900.00000000 | |||||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15C | 58100.00000000 | 62900.00000000 | |||||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
3 | 1 | 15C | CE | 58100.00000000 | 62900.00000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC