Scan, pay close attention to us Scan, download configuration BRIGHT BEACON (Beijing) Science and Technology Ltd. Beacon Product manual I. Product introduction Cloud beacon is a network sniffer based on iBeacon protocol. Through iBeacon and WiFi, to realize online iBeacon equipment information collection, at the same time, it can conduct online management on iBeacon base station in a certain range around. Support active and passive deployment, and realize the remote management and deployment, easy to collect data and information, so as to help enterprises to obtain more accurate data for marketing.
:Dimension Weight MicroUSB : MicroUSB interface RJ45 : RJ45 network interface Indicator light USB USB extending port Switch 1.1 Hardware interface function description Hardware interface Switch Mark ON/OFF Function description Short press to ON/OFF machine (default by boot) Long press to reset (clear configuration file) USB extending port sensor Support USB communication RJ45 network interface function extending port Support Ethernet cable interface MicroUSB interface 5V 1A Connect the power adapter to power a device Note: When USB extending interface external connected with high-power device (USB EVDO), it is recommended to use 5V 2A power adapter for power supply of device, ensure the normal operation of device. 1.2 Radio frequency information parameters Bluetooth specification Bluetooth smart 4.0 Bluetooth transmission power 20db Signal receiving sensitivity
-106dbm WLAN transmitted power 18db 1.3 Background management page Refer to CloudBeacon server-side user manual, see (II) below 1.4 Indicator light state description After device power on, light is slow flash, on for 500ms, off for 2s WIFI working, light is normally on. Bluetooth is scanning, light is slow flash, on for 500msoff for 5s Bluetooth connection is established, light is slow flash, on for 1soff for 2s Device is abnormal, light is quick flashing, on for 200ms, off for 200ms 1.4 Mobile phone software configuration procedure Refer to CloudBeacon mobile terminal operating tutorial, see (III) below II. Service terminal user manual 1. Register and login CloudBeacon management system login address is http://cloudbeacon.brtbeacon.com, it is recommended to use topspeed mode of Google browser however, QQ or 360 browser. If you do not have an account, please click the register link on top right corner. See Fig. 1-1 2. Binding CloudBeacon User login system for the first time, one needs to bind the purchased CloudBeacon to his own account, the system will show the bundled CloudBeacon. Bundled CloudBeacon process is as follows:
1. To generate the corresponding AppKey for CloudBeacon;
2. Download CloudBeacon mobile APP, when APP login, fill in AppKey and mail account (see the top right of page);
3. After APP success login, click [Binding]button, the prompt of success, click [CloudBeacon]
menu on the left of this page to check the bundled CloudBeacon. 3. Management interface After user login, there will list the bundled account CloudBeacon in CloudBeacon interface, see Fig. 3-1. Click On-line BEACON, will list the current CloudBeacon scanning to Beacon device. Click Morewill pop up the following menusee Fig. 3-2 Start scanningafter scanning starts, CloudBeacon will scan the peripheral Beacon device and Bluetooth, the store the scanned Beacon device information and Wifi probe data, and send them to CloudBeacon server, after CloudBeacon server received, it will show the Beacon device information on [On-line Beacon] function interface, and Wifi probe data will be shown on [Wifi probe] function interface. Data report configuration CloudBeacon will scan the data upload to cloudBeacon server in form of TCP mode, also can upload the scanned data to customers server in form of Http, upload the configuration parameter can also by this menu setting. Scanning device typein this menu, configurable CloudBeacon can scan the identified Beacon device type. Bluetooth settingin this menu, can configure CloudBeacon Bluetooth parameters. Unbundlinguser can unbundle the bundled CloudBeacon, after unbundling, this device will not be displayed in CloudBeacon list. Basic informationdisplay CloudBeacon basic information List abnormal deviceshow Beacon device with electric quantity lower than 30%. 4. On-line Beacon In CloudBeacon list, click [online Beacon] button, will list the current Beacon device scanned by CloudBeacon, as shown below:see Fig. 4-1 ConfigurationClick the information parameter of configurable Beacon Viewif the Beacon type cannot be identified, then only view the information parameter of Beacon;
Batch configurationTo select multiple Beacon and configure the same parameters at the same time;
Unfinished configurationin batch configuration, display the unfinished configuration of Beacon;
Finished configuration in batch configuration, display the finished configuration of Beacon Search According to the device name, Mac address, Major and Minor for fuzzy search. 4.1 Single Beacon configuration Click "Configuration" to configure single Beacon, as shown in the figure below (see Fig. 4-1-1) Fill in the Beacon parameters need to be modified, click [SAVE] button, the server will send Beacon parameters to CloudBeacon, CloudBeacon receives the parameters, will look up the corresponding Beacon configuration parameters, the whole process needs 10 to 60 seconds, after configuration complete, system will prompt success or failure information. 4.2 View Beacon parameter If the type of the Beacon cannot be recognized, then the Beacon parameters cannot be configured, can only view the Beacon parameters, as shown in the figure below: (see figure 4-2-1) 4.3 Batch configuration If a large number of Beacon need configuration, using single configuration function is very time-consuming; Use [batch configuration], can select multiple Beacon at the same time configure the same parameters, is very convenient. As shown in the figure below (figure 4-3-1) Select the Beacon in configuration, and then click "batch configuration" and show the following configuration interface (as shown in figure 4-3-2) Before configuring the designated parameter, user needs to select the configured parameter, configuring Major parameter for example, one needs to select Major parameter click button can make Major and Minor increasing based on previous Beacon. Click system will submit the configuration for background processing automatically, then return to online Beacon interface. In online Beacon interfacecan click and to view the configuration results. 5. WIFI probesee Fig. 5-1-1 6. Other configuration Data report configurationsee Fig. 6-1-1 CloudBeacon basic informationsee Fig. 6-1-3 III. CloudBeacon Mobile terminal configuration of network connection and binding 1. Power on CloudBeaconCloudBeacon adopts Micro USB for power supply it recommended 5V 1A power adapter for device power supply. 2. Download CloudBeacon configuration APP. Download linkhttp://fir.im/cloudbeacon, or log in CloudBeacon management backgroundhttp://cloudbeacon,brtbeacon.com, And download in Appkey management page. Scan 2D barcode to download 3. Connect the phone WIFI to CloudBeacon emission WIFI. Open the phone Settings function select WLAN, select CloudBeacon emitted WIFI in attachment WALN list, CloudBeacon emitted WIFI name is named by BRTXXXX, click to enter the password, default password is 12345678. 4. Turn on CloudBeacon configuration terminal APPsee Fig. 3-1-1 5. Enter the user name and password, the user name and password are the account and password of developer center (login function here is to record the user's accounts, but also have to enter the correct username and password, and will be validated when binding the device). As shown in figure 3-1-2 6. Add CloudBeaconsee Fig. 3-1-3 7. Choose online pattern. CloudBeacon provides two online patterns, respectively are limited connection and STA mode, limited connection refers to connect intent network cables from network ports, the STA mode refers to by setting to connect CloudBeacon connected to surrounding WIFI to get to the Internet, here we mainly illustrate the STA mode configuration. As shown in figure 3-1-4 8. Add APPKeyoperation procedure as shown below 9. CloudBeacon list interfacesee Fig. 3-1-4 Click CloudBeacon information to enter into available WIFI list surround CloudBeacon 10. CloudBeaocn surrounding WIFI management interface. After entering into CB surrounding wifi management interface, it will determine whether the CB is connected to network or not, if it is connected to network , then directly operate binding CB with user account, if it is not connected to network, then load the available WIFI list surrounding CB device (here mainly show operation without network connection). 11. STA mode CB binding with user aBind CloudBeacon binding b. Verify the device is connected to the network or not, as shown in figure 3-1-5. c Verify the user information d APP background operation binding.