2018 User Manual ZCC RB4 FCC ID :2AR3JRRB4 Introduction Thank you for buying ZCC RB4! For support and help, please, e-mail at support@myremoto.com or call +7.495.929.7075. What is ZCC RB4?
ZCC RB4 is a TCU installed inside a motor car to perform the functions as follows:
Digital CRM (news & special offers, dealers, services) geo-fencing, area control) Motor car health checking (customer report, GPS tracking (trips, current speed/RPM, geo-location, OEM/dealership report) Push notification messages (road accidents, towing, speeding) Please, see figure 1 for the general look of ZCC RB4 from two different views. Fig ure 1 Specification Please, see table for detailed specification of ZCC RB4. Table 1. Technical parameters and characteristics Technical Parameter or Characteristic Technical Parameter or Characteristic Value Microprocessor Control Unit (MCU) Core Flash Memory Static RAM FOTA update LTE Type LTE CAT-M1(eMTC) WiFi Bluetooth Xtensadual-core 32-bit LX6 microprocessor up to 600 DMIPS Frequency up to 240 MHz 448 Kbytes 16 Kbytes GPRS connection GSM Module Tri-Band FDD-LTE B2/B4/B12/B13 Uplink up to 375kbps, Downlink up to 300kbps Communication 802.11 b/g/n (2.4 GHz), up to 150 Mbps BLE specifications GNSS Module Types of GNSS supported GNSS receiver Accelerometer Gyroscope CAN data fusion Cold start Hot start GPS/GLONASS 48 tracking / 2 fast acquisition channels Yes Yes Yes 30 sec
<1 sec Bus pins fault protection ISO 11898-2 compliance CAN bus Connection
> 36 nV Yes Yes 1 Mbit/sec 7 12 V Yes Yes K-Line (ISO9141) Connection 38 Kbit/sec Data Storage 16 Mb 2/4/8/16 g GIFT/ICT Data Transfer Rate Common Mode Range Thermal Shutdown support K-Line connection with 1 K master resistor Data transfer rate Flash memory Leaner acceleration sensing range Angular rate measurement range 125/245/500/1000/2000 dps iNEMO Inertial Module (3D Accelerometer and 3D Gyroscope) High-performance mode Embedded temperature sensor up to 1.6 kHz Yes Power Supply Power supply voltage Current (max.) Current (average) Current (deep sleep mode) 5 18 V 300 mA 60 mA 1 mA Dimensions Weight Highest output power Mechanical Characteristics 55 mm 49 mm 22 mm 50 g Frequency Band CAT M1 FDD2 CAT M1 FDD4 CAT M1 FDD12 CAT M1 FDD13 WiFi 2.4 G (802.11 n mode) BT Max power(dBm) 21.85 22.09 22.25 22.67 17 5 Distribution Kit The distribution Kit of ZCC RB4 components as follows:
ZCC RB4 main body Installation Kit. comprises the parts and Installation To install ZCC RB4 onto your motor car, please, follow these instructions below. Contact your dealer center to inquire about the installation process OR Contact your dealer center to have the installation procedure performed by a qualified staff person. WARNING! The installation of ZCC RB4 inside the motor car should be performed by a qualified technical stuff. Please, install ZCC RB4 onto your motor car only after reading this user manual. WARNING! THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) INTERFERENCE RECEIVED, THIS DEVICE MUST ACCEPT ANY INCLUDING INTERFERENCE CAUSE UNDESIRED OPERATION THAT MAY WARNING! NOTE:
THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. interference in a residential NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
installation. Increase the separation between the equipment and
- Reorient or relocate the receiving antenna.
-
receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. Use Please, download and install mobile app onto your mobile device
(both Android and iOS-based supported). Please, see the embedded Help for further assistance. Contacts E-mail: info@myremoto.com tel.
+7.495.929.7075 Mail Address: Ugreshskaya St., 2, suite 53, Moscow, Russia, 109089