Table of Contents Chapter 1 System Configuration NOTE:
CHAPTER 1 SYSTEM CONFIGURATION 1-1 SYSTEM GENERAL INFORMATION 1-2 PRECAUTIONS 1-3 START TO ASSEMBLY YOUR SYSTEM UNIT 1-4 1-5 1-6 1-7 1-8 INSTALLATION OF SLIM HDD INSTALLATION OF SLIM FDD 1.44 MB INSTALLATION OF SMART CARD READER INSTALLATION OF CPU INSTALLATION OF MEMORY CHAPTER 2 SMART CARD SETUP 2-1 SOFTWARE DRIVER INSTALL 2-2 OPERATION SEQUENCE 4 1 1 5 6 7 8 9 10 11 12 12 14 1-1 System General Information The Rear Panel
(1). Power inlet
(2). COM1 port
(3). PS/2 Mouse connector
(4). PS/2 Keyboard connector
(5). Ethernet RJ-45 connector
(6). Parallel port
(7). USB port
(8). VGA connector
(9). COM2 port 5 1 The Front Panel
<2> FRONT PANEL BOARD (TCP)
(1). USB
(2). USB
(3). MIC
(4). Line in
(5). Line out
<1> ESLOT BOARD
<3> COMPACT FLASH ADAPTER (TCC) Top site Bottom site 2 3
(5) SMART Card Reader CONNECTOR Motherboard: CON1 Pin# Assignment 1 Receive data 2 Clear to send 3 Transmit data 4 Request to send 5 GND 6 Reader on 7 Card CTRL 8 VCC5VSB 9 GND Reader: J1 Pin# Assignment 1 RX 2 CTS 3 TXD 4 RTS 5 GND 6 Reader On 7 CTRL 8 9 GND VCC5VSB 1-2 Precautions Electrostatic discharge (ESD) can easily damage your motherboard. Observing a few basic precautions can help you safeguard against damage that could result in expensive repairs. Follow the measures below to protect your equipment from static discharge:
** Keep the Motherboard and other system components in their anti-static packaging until you are ready to install them.
** Touch a grounded surface before you remove any system component from its protective anti-static packaging. A grounded surface within easy reach is the expansion slot covers at the rear of the system case or any other unpainted portion of the system chassis.
** During configuration and installation, touch a grounded surface frequently to discharge any static electric charge that may build up in your body. Another option is to wear a grounding wrist strap.
** When handling a motherboard or an adapter card, avoid touching its components. Handle the motherboard and adapter cards either by the edges or by the mounting bracket that attaches to the slot opening in the case. Battery Caution:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturers instructions. 4 5 1-3 Start to Assembly Your System Unit 1-4 Installation of Slim HDD Before assembling your system unit, two steps have to be followed:
Follow these steps to install the slim HDD 1. Remove the screw from the tray 2. Push the slim HDD tray back to remove it Remove ~ screws Uncover the case from the system unit 3. Put slim HDD on the tray 4. Insert the four screws and fully tighten with a suitable screwdriver 5. Pick the HDD cable from the packing bag 6. Insert one head with 44 pin to the slim HDD, the other one with 40 pin to motherboard IDE1 and match two HDD power connectors together 6 7 1-7 Installation of CPU Follow these steps to install the CPU 1-8 Installation of Memory Follow these steps to install Memory 1. Repeat steps 1 to 3 in 1-5 for removing the trays and ESLOT card 1. Repeat steps 1 and 2 in 1-4 for removing the slim HDD tray Read the ESD Precautions before you unpack and install the CPU. Make sure that the system power is off before you install any component. Read the ESD Precautions before you unpack and install the Memory. Make sure that the system power is off before you install any component. 2. Pull up the CPU socket lever. See step 1 in illustration 3. Insert the CPU into the socket. Make sure that pin 1 of the CPU matches the hole-1 of socket 4. Pull down the socket lever to lock the CPU into the socket. See step 2 2. Before inserting the DIMM, make sure the pin1 of the DIMM matches with the pin1 on the DIMM socket 3. Insert DIMM into the DIMM sockets at a 90-degree angle and press down 10 11 Chapter 2 Smart Card Setup 2-1 Software Driver Install
(1) Enter the IC-Card subdirectory and double-click Setup.exe
(2) Click OK at the Welcome screen
(4) Click Continue at the Choose Program Group.
(3) Click Setup button to install User Card Management software.
(5) The driver files will now be installed. When finished installing, click the OK to complete your installation. 12 13 2-2 Operation Sequence
(3) Test COM Port The purpose of this form is to modify User Card management. First, set the port, then, input personal information, change User card key and exit.
(1) Set COM Port Set COM port which the user writes/reads. Click here into setting COM port. OK
(4) Input Personal Information
(2) Setting COM Port Select com1 or com2, press Ok to confirm COM port or press cancel to reset. Press OK button to test port, if successes, return message Port number set OK! go on step (4). Otherwise return message Error! you must reset COM port and test again, that means repeat step 2 and step 3 until success. The card will store some message of the card user. Click here to input it. 14 15
(5) Enter Personal Information
(7) Read Your Personal Information Please enter the personal information, name, address, ID and sex into the text box. Tom Room 2524, GuoMao Building RenMin South Road, Shenzhen Note: Name maximum length is 8 00001 characters. Address maximum length is 132 characters. ID maximum length is 15 characters. Press this Read button, then you can read Personal Information youve written now. Tom Room 2524, GuoMao Building RenMin South Road, Shenzhen 00001
(6) Test Personal Information
(8) Change Personal Information Press Write button. Return message finish! Then, you can confirm it. OK Press this Edit button, then you can read/change Personal Information as you like now. 16 17
(9) Clear Personal Information
(11) Validate Current Card Key Press Clear button, then you can clear all the Personal Information of yourself.
(10) Change User Card Key
(12) Enter your new key and confirm If you want to change user card key, that means change your password of the card. Just click here. The current key is the key you are using, Enter your current card key in the text box, its maximum length is 8 characters, then click OK to validate current card key. Note: The default of current key of a new user card is 11111111. The New Key is the key you will use. Its useful if you want to change the key. Its max length is 8 characters, input your new key in the text box, then repeating input the new key in reconfirm new key text box. Then press OK. 18 19
(13) Validate New Key
(14) Exit Press Write button, return message OK. Or select Exit to rewrite. If you have finished the entire step above correctly, you could exit this form by pressing the Exit. 20