1 2 3 4 5 6 SMART DI MME R SW I TC H Dimmer Switch In the box Installation labels Features Install using the Brilliant app Step 1 Download the app Download the Brilliant app from the Apple Store or Google Play Store. Step 2 Follow installation guide in app Receive step-by-step installation instructions using the Brilliant app. Before you begin Heres what you need to know before you expand your Brilliant Smart Home System with the Brilliant Dimmer Switch. REQUIREMENTS Brilliant Control: At least one Brilliant Control must be installed for Brilliant Switch to work. Neutral & Ground Wires: Use the Brilliant app to conrm that your electrical wiring is supported. Electrical:
- 120V AC
- up to 500W incandescent/halogen
- up to 200W LED/CFL
- Magnetic low voltage (MLV) lighting not supported. Tools: Non-contact voltage detector, Philips screwdriver, standard screwdriver, pliers Quick Start Guide Screws Wire nuts x5 Wire labels 1 Ground Ground 1 Neutral Neutral 1 1 1 Line Line Load Load Traveler Traveler 1 1 1 1 1 Gang box labels Line Load Motion Sensor Set up with app Slider Dim lights:
Swipe up/down Touch Plate On/Off:
Tap anywhere Activate scene:
Double tap LED Set up with app Safety Disconnect Reset Dimmer Switch Front Back 7 8 9 10 11 12 Troubleshooting Works with Legal Legal Want to learn more about what you can do with your Brilliant Dimmer Switch?
Blue Blinking: Error detected, reset Dimmer Switch Visit www.brilliant.tech LED Status Indicator White Blinking: Powered on and ready to be set up White Solid: Successfully set up and connected to your home Reset Instructions 1 Pull out Safety Disconnect (clear plastic tab over LED) until LED turns off. 2 Push in Safety Disconnect until LED turns on. 3 Place your nger on Touch Plate and hold for 6-10 seconds until LED blinks white. 510-00008 REV 2 Need additional help?
http://support.brilliant.tech The Brilliant Smart Home System Transform any house or apartment into an easy-to-use smart home. Home Control Dimmer Switch required This device contains licence-exempt transmitter(s)/re-
ceiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
1.This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes
: 1. Lappareil ne doit pas produire de brouillage; 2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den comprom-
ettre le fonctionnement.
& more Smart Plug Mobile App interference limits are designed NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must acceptany interference received, that may cause undesired including operation. These to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does interference to radio or television cause harmful reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC CAUTION Changes or modications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Pantone 314 Pantone 1495