The Digital Door Viewer!
PHV1330M Package Contents 3 5 1 2 4 6 7 10 8 9 1 PHV1330M 2 PHV1330M Transmission 3 4 MicroSD PHV1330M Receiver 5 6 7 Base Flange PeepHole Lens PeepHole Barrel 8 9 Washer Tightening Tool Installation- PHV1330M 1 5 2 3 4 Insert PeepHole lens in the outside of the door. Insert the PeepHole barrel through the Washer and Base Flange and insert both into the hole on the inside of the door. Tighten the PeepHole Barrel with your fingers. When the barrel is snug, rotate the Base Flange until the TOP icon is at 12 oclock (vertical). Use the Tightening Tool included to tighten the PeepHole barrel. 6 7 Hold the PeepHole Viewer at a -25 degree counter-clockwise position and insert it onto Base Flange. Rotate the PeepHole Viewer clockwise until horizontal and you feel it lock in place. Use the screwdriver to tighten the Locking Screw. 10 11 Installation- PHV1330M Transmission 10 Screw 11 Holder 1 2 3 4 Note Place your PHV1330M transmission on our suggestion location Indoor Outdoor Indoor Outdoor D2*
D1*
A1*
9 Open battery Cove then install 2AA batteries Install Holder and tightening the screw Tear off the cover of double-side glue. Test the detector of Motion Activated Sensor Green: Detecting Red: Battery Low a. Place on ceiling above the porch and face b. Place above door, and adjust the Motion to ground. D1: Detected distance: 5 meters D2: Signal received distance: 5 meters Activated Sensor angle, face to ground. A1: Detected angle: 60 5 6 8 11 Functions Change Viewing Modes Low Light Level Enhancement Playback Images Image Recording 1 Locking Screw 2 Micro Sd card Slot 3 Low Battery Light 4 Power Button 5 Brightness Enhanced Switch 6 UP/ Time Setting 7 Down/ Playback 8 Battery Cover 10 9 Holder 10 Screw 11 LED light Package Contents Install Batteries, Recevier, and MicroSD card Set Date and Time 1 2 3 2
1 OK 3 4 Date & Time 2011/ 3/31 12:30 Set Exit Date & Time 2011/ 3/31 12:30
: OK to next 5 Date & Time 2011/ 3/31 12:30
: Done
1 Open battery cover 2 Install 2 AA batteries and Recevier 3 Insert MicroSD card 1 2 Turn on PeepHole Viewer Press "UP" button for 3 seconds 3 4 Select "Set" to enter setting mode Set the date and time Done 5 1 2 On B Off A 1 2 Hold power button for 1 second to see "Regular" image. Press power button again to change the viewing modes to see
"Zoom" image . When outside environment is too dark to see, you can turn on Low Light Level Enhance mode, it will increase the image brightness. A. Off B. On Specification PHV1330M Model:
PeepHole barrel:
Sensor:
LCD Screen:
Storage:
Power:
Accessories:
Size:
Weight:
PHV1330M
- 12 mm
- fits any door 35~57mm( 1.38~2.24) thick.
- View Angle: Regular Mode : 96 , Zoom Mode: 60
-1.3 Mega Pixel CMOS 3.0 TFT Micro SD card (Maxmium is 32 GB, recommend is 8 GB) 2 AA batteries (good for approx.1300 "peeps") Base Flange, Tightening Tool, PeepHole, 2 AA Batteries, User Manual 87(W)x 158(H)x 33(D) mm 160 g (without batteries) PHV1330M Transmission Model:
Detect Angle:
Detect Distance:
Receiver Distance:
Power Source:
Accessories:
Size:
Weight:
PHV1330M Transmission 60 3~5 meters 5 meters 2 AA batteries Holder, Recevier, 2 AA Batteries, User Manual 66(W) x 90(H) x 24(D) mm 20 g (without batteries) On Zoom Off x 3 x 3 x 3 1 2 3 1 Turn on PeepHole Viewer Press "Down" button to 2 watch playback images. Press "Up" and "Down"
button to review images. 3 PeepHole viewer will record 3 pictures at below status:
1. Power on 2. See zoom view 3. Power off After 10 seconds of inactivity you will leave playback mode. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) this device must accept any interference received, including interference that may cause undesired operation. Parts of Device 1 2 3 4