FCC ID: QDS-BRCM1005-E 54g WLAN Mini PCI Card

Notebook PC User's Guide Model: W730-P4/ W730-K8/ W730-K7 First Edition: January 2004 User's Guide NOTICE Specifications and information found in this guide are subject to change without notice. Any changes therefore will be incorporated in future editions. The manufacturer assumes no responsibility for errors or omissions in this document. Windows XP is the trademark of Microsoft Corporation. Intel is the trademark of Intel Corporation. AMD is the trademark of AMD Corporation. Other trademarks are properties of their respective owners. TRADEMARKS Page II User's Guide Standards The following standards are adopted throughout this guide:

Notebook in boldface (with or without capitalization) refers to the notebook computer that you have purchased. Boldface type is also used to highlight important information in this document. The messages that appear on the Notebook screen will be boxed when they are referenced.

Whenever extra caution is called for, the information will be boxed in a dark frame preceded by "Note:" or "Warning:"

Usually after performing a step-by-step instruction, you will be asked to:

Press the Esc key Which means you should press the corner of the keyboard. key located at the upper left-hand

Page III Users Guide Contents CONTENTS CHAPTER 1 BEFORE YOU BEGIN .................................................. 1-1 1.1 CHECKING WHAT YOU RECEIVED .......................................................................1-1 EXAMINING YOUR COMPUTER .............................................................................1-2 1.2 THE FIVE STATUS LEDS .......................................................................................1-6 1.3 1.4 THE TWO POWER LEDS........................................................................................1-7 1.5 THE SEVEN SYSTEM BUTTONS ............................................................................1-8 ATTENTION ON HANDLES AND SOCKET DOORS ................................................1-9 1.6 1.7 THE <FN> KEY....................................................................................................1-10 CHAPTER 2 BATTERY ........................................................................ 2-1 2.1 BATTERY PACK......................................................................................................2-1 2.2 RECHARGING THE BATTERY PACK ......................................................................2-1 2.3 QUESTIONS AND ANSWERS...................................................................................2-2 2.4 BATTERY MAINTENANCE .....................................................................................2-3 2.5 POWER CONSUMPTION..........................................................................................2-3 2.6 REDUCING POWER CONSUMPTION.......................................................................2-4 2.7 REMOVING THE BATTERY PACK..........................................................................2-5 CHAPTER 3 MEMORY ........................................................................ 3-1 3.1 REMOVING MEMORY MODULE ............................................................................3-2 CHAPTER 4 MINI-PCI MODULE...................................................... 4-1 4.1 REMOVING MINI-PCI MODULE ...........................................................................4-1 CHAPTER 5 THE HDD DRIVE........................................................... 5-1 5.1 REMOVING THE HARD DISK DRIVE.....................................................................5-1 APPENDIX A- AGENCY REGULATORY NOTICES ................... A-1 APPENDIX B- ENVIRONMENT........................................................ B-1 Page V User's Guide Before You Begin Chapter 1 Before You Begin Please read this section before you start using your computer. 1.1 Checking What You Received Your notebook package should contain the following items:

The Notebook. AC Adapter. AC Power Cord. CD Disc (Including Drivers and Users Guide). Battery Pack. Note: You should keep the original factory carton and packing materials in case you need to ship the unit back for servicing. Page 1-1 Before You Begin User's Guide 1.2 Examining Your Computer Before you start using your computer, you need to get acquainted with your notebook's main features and interfaces:

Cover Latch LCD Screen Seven System Buttons Optical Drive Touch Pad Ventilation Grills Keyboard Speaker Five Status LEDs Two Power LEDs Speaker Panoramic View Page 1-2 User's Guide Before You Begin Cover Latch Speaker Woofer HDD Drive Front View Speaker Woofer RJ45 LAN Connector RJ11 Fax/Modem Connector DC-In VGA Port Ventilation Grills Kensington Lock S-Video Connector

(Optional) Headphone Microphone USB Ports Rear View Page 1-3 Before You Begin User's Guide CF Card Eject Handle CF Card Socket Door 4-in-1 Socket Door

(for MMC/MS/SD/CF Cards) Ventilation Grills IEEE1394 Connector (Optional) USB Ports Left View PCMCIA Socket Door PCMCIA Eject Handle ODD LED Eject Button Emergency Hole Right View Optical Drive Page 1-4 User's Guide Before You Begin Mini-PCI Door Battery Pack Two Battery Latches DDR Memory Door Ventilation Grills HDD Door Bottom View Stereo Connector:

Your headphone jet should have this type of connector as shown here Mono Connector:

Your microphone jet should have this type of connector as shown here. Two Types for Audio Jet Page 1-5 Before You Begin User's Guide 1.3 The Five Status LEDs The AC Adapter LED This LED would be lit when system is connected to an AC adapter. The Wireless LED This LED would be lit when the wireless function is activated. The Caps Lock LED The LED would be lit when the keyboard is in Caps Lock mode. In this mode, all characters you type are in uppercase. The Num Lock LED This LED would be lit when the keyboard is in Num Lock mode. In this mode, the embedded numeric keypads can be used. The HDD Access LED This LED would be lit when system is accessing the HDD. Note: The Five Status LEDs are located near the two click buttons of the touch pad. For exact location, please refer to the Panoramic View diagram in Chapter 1.2. Page 1-6 User's Guide Before You Begin 1.4 The Two Power LEDs The Power On LED Below is how the LED would behave in different situations:

Off On Blinking System is powered off, or in Hibernate mode. System is in Standby mode. System is powered by AC adapter, and/or System is in full operation. The Battery Pack LED Below is how the LED would behave in different situations:

On Blinking Off Battery pack is being recharged: fast-charge or pre-charge. Battery pack is consuming down to 10% level. Battery pack is waiting for recharge when battery temperature is too high after discharge. Battery pack error. Battery pack is not under recharge. Note: The Two Power LEDs are located near the Five Status LEDs. For exact location, please refer to the Panoramic View diagram in Chapter 1.2. For more details on Standby and Hibernate, please refer to Power Options (for Windows Systems) in the Control Panel of your Microsoft Windows operating system. Page 1-7 Before You Begin User's Guide 1.5 The Seven System Buttons The Power Button This Power Button is programmable by user. For detail on how to program this button, please refer to the Power Options of Control Panel in Windows System. Search Button Press this button to activate the search function. Internet Button Press this button to activate the internet function. Email Button Press this button to activate the email function. Volume Up Button Press this button to increase volume. CD Play Button Press this button to playback audio CD. Volume Down Button Press this button to decease volume. Note: When the two system buttons, Volume Up Button and Volume Down Button, are pressed together, the sound volume would be muted. Note: The Seven System Buttons are located near top right of keyboard. For exact location, please refer to the Panoramic View diagram in Chapter 1.2. Page 1-8 User's Guide Before You Begin 1.6 Attention On Handles And Socket Doors 4-in-1- Slot for MMC/MS/SD/CF cards CF Card Slot PCMCIA Slot The CF card handle is retracted The PCMCIA handle is retracted The CF card handle is protruded out The PCMCIA handle is protruded out. Please observe below safety measures:

Make sure the PCMCIA eject handle does not protrude out at all the time, unless you are using the handle to eject PCMCIA card. A protruded handle is prone to external interference; such as ramming by an inkjet printer or external keyboard. When PCMCIA card is not inserted into the PCMCIA socket, make sure this socket is covered by the PCMCIA socket door as supplied together with this notebook. The purpose of this PCMCIA socket door is to prevent foreign matters from entering into the system unit through this socket, when PCMCIA card is not inserted. Make sure the CF card eject handle does not protrude out at all the time, unless you are using the handle to eject CF card. A protruded handle is prone to external interference;

such as ramming by an inkjet printer or external keyboard. When CF card is not inserted into the CF card socket, make sure this socket is covered by the CF card socket door as supplied together with this notebook. The purpose of this CF card socket door is to prevent foreign matters from entering into the system unit through this socket, when CF card is not inserted. When no card (Multi-Media Card/Memory Stick/SD Card/CF Card) is not inserted into this 4-in-1 socket, make sure this socket is covered by the 4-in-1 socket door as supplied together with this notebook. The purpose of this 4-in-1 socket door is to prevent foreign matters from entering into the system unit through this socket, when no card is inserted. Page 1-9 Before You Begin User's Guide 1.7 The <Fn> Key The <Fn> Function Key is located near the bottom-left corner of the keyboard. This key is used together with other keys to activate certain pre-defined functions. To activate these functions, press and hold down <Fn> together with the keys described below:

LED Toggle Press this key combination (Fn+F1) would toggle on and toggle off all LED lights. To minimize visual distractions, you may like to toggle off all LED lights during DVD software playback. Wireless LAN Press this key combination (Fn+F2) to activate the wireless LAN function. Suspend Press this key combination (Fn+F3) to have system enter the Suspend mode. In Suspend mode, the black light of the display panel would be turned off and a host of internal devices would enter into a stage of lower power consumption. Press any keycap on the keyboard to resume normal operation. LCD/CRT Switch Press this key combination (Fn+F4) to switch between LCD only, CRT only, and LCD/CRT simultaneously. Brightness Decrease Press this key combination (Fn+F7) to decrease the brightness of the LCD display. Brightness Increase Press this key combination (Fn+F8) to increase the brightness of the LCD display. Page 1-10 User's Guide Before You Begin Play/Pause This hot-key is for audio CD disc playback. Press this key combination

(Fn+F9) to play or pause audio play back. Stop This hot-key is for audio CD disc playback. Press this key combination

(Fn+F10) to stop audio playback. Previous Track This hot-key is for audio CD disc playback. Press this key combination

(Fn+F11) to skip to the previous track. Next Track This hot-key is for audio CD disc playback. Press this key combination

(Fn+F12) to skip to the next track. Page 1-11 User's Guide Battery Chapter 2 Battery 2.1 Battery Pack Your notebook is equipped with a high energy rechargeable Lithium Ion (Li-Ion) battery pack. In general, a fully charged battery pack can support around 2.0~3.0 hours of operation, with Windows Power Management option enabled. However, difference in configuration (CPU, HDD, Memory etc.) and system utilization (especially I/O activities) can affect the operation time greatly. 2.2 Recharging the Battery Pack Your notebook supports both on-line and off-line recharge. Follow the procedure below to recharge battery:

Make sure the battery pack is installed in the notebook. Connect the AC adapter to the notebook and to an electrical outlet. When a battery pack is being recharged, its battery LED (located near the Five Status LEDs) would be lit up. For details on the LEDs, please refer to Chapter 1.3. When the notebook is OFF, a depleted Li-Ion battery will take three hours to recharge. Page 2-1 Battery User's Guide 2.3 Questions and Answers Q: I can feel the heat next to the Touch Pad during recharge. Is it normal?

A: The battery will generate heat during recharging and discharging. There is a protection circuit inside the notebook to prevent overheating. User needs not to worry. Q: My battery operation time is not as long as it should be. Why?

A: The battery is heat sensitive and can only be charged to its maximum if the battery and its environmental temperature remain within 15-25C (59-77F). The more the temperature deviates from this range during recharging, the less chance there is for the battery to be fully charged. In order to recharge the pack to its full capacity, users are requested to cool down the unit by unplugging the AC Adapter. Wait until it is cooled down. Then plug in the AC Adapter to start recharging again. Q: I did not use my spare battery for a few days. Even though it was fully recharged, A: The batteries will self-discharge (1% per day for Li-Ion) when they are not being there wasn't as much power left as a newly charged one. Why?

recharged. To make sure a battery pack is fully charged, recharge before use. Always keep the battery inside the notebook and have the AC adapter connected whenever possible. Q: I did not use my spare battery for months. I have problem in recharging it. A: If you happen to leave your battery pack to go through an extended period of self-

discharge, say more than three months, the battery voltage level will become too low and needs to be Pre-Charged (to bring the battery voltage level high enough) before it automatically (for Li-Ion only) resumes its normal Fast Charge. Pre-

Charge may take 30 minutes. Fast Charge usually takes 2~3 hours. Page 2-2 User's Guide Battery 2.4 Battery Maintenance To maintain the battery pack's maximum capacity, you should occasionally let the notebook deplete its battery power completely before recharging. To carry out a complete depletion of the battery, disconnect the AC adapter and let your notebook consume the remaining battery power. To speed up the depletion, use the HDD as much as possible, and the LCD should be set as bright as possible. When the battery is empty, wait for the notebook to cool down (especially the battery). The temperature should be within 15-25C (59-77F). Then insert the AC adapter to recharge the battery. 2.5 Power Consumption The Windows XP, the latest Windows operating systems, has incorporated the latest state-of-the-art ACPI (Advanced Configuration Power Interface) power management methodology. In order to fully utilize the power of your battery pack, it would be a good idea for you to spend sometime to acquire a basic understanding of the power management concept from your operating system. In Windows Operating Systems, you can go through Power Options of the Control Panel according to the version of Windows Operating System the notebook applies. We shall not describe them in details. The Power Options in Windows XP are further divided into as below:

Power Schemes Alarms Power Meter Advanced Hibernate Page 2-3 Battery User's Guide 2.6 Reducing Power Consumption Although your notebook (together with the operating system) is capable of power conservation, there are measures you can take to reduce the power consumption:

Use the AC power whenever possible. Lower the intensity of the LCD backlight. A very bright screen translates to higher Try to use the HDD or the PCMCIA drive to read and write files, instead of using power usage. the external USB FDD. Note: The battery pack should be locked in the battery compartment all the time. Page 2-4 User's Guide Battery 2.7 Removing The Battery Pack This battery pack can easily be removed and replaced. Make sure that the computer is properly shutdown before changing the battery pack. If you would like to change the battery pack while power is on, make sure this battery pack is not the only electrical source to the system unit. Follow the steps below to remove the battery pack. To insert the battery pack, reverse the steps above. Make sure the system is properly shutdown. Flip the system upside down. Push the two battery latches to the unlock position as shown by #1 and #2

(Enlarged Diagram). Maintain the latch in the unlock position. Remove the battery pack as shown. Page 2-5 User's Guide Memory Chapter 3 Memory Your notebook is equipped with a configurable memory unit. The industry standard JEDEC DDR S.O.DIMM memory module socket is available for memory upgrade to 1024MB. The table below illustrates all the possible ways system memory can be configured. Two types of DDR S.O.DIMM are available in the market: PC2100 (DDR266) and PC2700 (DDR333). If it occurs that system is installed with both the PC2100 and PC2700 S.O.DIMMs, the overall speed would be downgraded to DDR266. Total Memory 256MB 384MB 512MB 768MB 512MB 640MB 768MB 1024MB In-System Memory 256MB 256MB 256MB 256MB 512MB 512MB 512MB 512MB SODIMM Memory 0MB 128MB 256MB 512MB 0MB 128MB 256MB 512MB Groove for indicating the orientation of the module 1.25 max DDR S.O. DIMM Memory Module Page 3-1 Memory User's Guide 3.1 Removing Memory Module Below is the procedure on how to remove the memory module. The Groove Make sure the system is properly shutdown. Flip the system upside down. Remove the screw as shown by #1. Remove the compartment door as shown by #2. Press the spring-locks sideways as shown by #1. The memory module would pop up as shown by #2. Remove the memory module as shown by #3. To insert the memory module, reverse the steps above. Page 3-2 User's Guide Mini-PCI Module Chapter 4 Mini-PCI Module Your notebook is equipped with a Mini-PCI module. The Mini-PCI supports wireless LAN function. 4.1 Removing Mini-PCI Module Below is the procedure on how to remove the Mini-PCI module. The Groove Make sure the system is properly shutdown. Flip the system upside down. Remove the screw as shown by #1. Remove the compartment door as shown by #2. Press the spring locks sideways as shown by #1. The Mini-PCI module would pop up as shown by #2. Disconnect the two cables as shown by

#3. Note, there are two types of mini-PCI module. Externally, they look slightly different; especially on the locations of the cable connections. To insert the Mini-PCI module, reverse the steps above. Page 4-1 User's Guide The HDD Drive Chapter 5 The HDD Drive Your notebook is equipped with an industry standard 2.5/9.5mm hard disk drive. 5.1 Removing The Hard Disk Drive Below is the procedure on how to remove the hard disk drive. Make sure the system is properly shutdown. Flip the system upside down. Remove the screw as shown by

#1. Remove the HDD drive as shown by #2. To insert the hard disk drive, reverse the steps above. Page 5-1 Users Guide Appendix A Appendix A- Agency Regulatory Notices A.1 Safety Instructions CAUTION: Please read these safety instructions carefully. CAUTION: Please keep this User's Manual for future reference. CAUTION: Please disconnect this equipment from AC outlet before cleaning. DO NOT use liquid or sprayed detergent for cleaning. Use a clean moistened cloth. CAUTION: The wall socket used should be positioned near the equipment and should be easily accessible. CAUTION: Please keep this equipment free from humidity. CAUTION: Place the equipment on a reliable surface at all times. A drop or fall can cause severe damage. WARNING: The openings of the enclosure are for air ventilation and are meant to protect the equipment from overheating. DO NOT COVER THE VENTILATION OPENINGS. Page A-1 Appendix A User's Guide CAUTION: Verify the voltage of the power source before connecting the unit to any power outlet. WARNING: DO NOT step on or place anything over the power cord. CAUTION: All cautions and warnings on the equipment should be noted. WARNING: If the equipment is not used for a long period of time, disconnect the equipment from the power source to avoid damage from power spikes. WARNING: NEVER pour any liquid into any openings; a fire or electrical shock is possible. WARNING: For safety reasons, other than pre-designated ports, doors, and the equipment should be opened only through qualified service personnel. CAUTION: If one of the following situations should arise, the equipment should be checked by an authorized technician:

a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to excessive moisture. d. The equipment does not work well, or you fail to get it to work according to user's manual. e. The equipment has been dropped or damaged. f. The equipment has obvious signs of breakage. Page A-2 Users Guide Appendix A CAUTION: DO NOT LEAVE THE EQUIPMENT IN TEMPERATURES BELOW -20C(-4F) OR ABOVE 60C(140F). IT MAY CAUSE DAMAGE TO THE EQUIPMENT. WARNING: Never install modem/telephone wiring during a lightning storm. WARNING: Never install modem/telephone jacks in wet locations unless the jack is specially designed for wet locations. WARNING: Never touch un-insulated modem/telephone wires or terminals unless the modem/telephone line has been disconnected at the network interface. CAUTION: Use caution when installing or modifying modem/telephone lines. WARNING: Avoid using a modem/telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. WARNING: This computer contains an internal lithium battery-powered real-time circuit. There is a risk of explosion and injury if the battery is incorrectly replaced or handled. Do not attempt to recharge, disassembled, immerse in water, or dispose of it in fire. Replacement should be done through your notebook dealer. Page A-3 Appendix A User's Guide WARNING: THE CD-ROM/DVD-ROM IN THIS NOTEBOOK EMPLOYS A LASER SYSTEM. a. To ensure proper use of this product, please read the relevant instructions carefully and retain for future reference. b. Should the unit ever require maintenance, contact your local dealer. c. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. d. To prevent direct exposure to Laser Beam, do no try to open the enclosure. CAUTION: The internal CD-ROM/DVD-ROM drive is classified as a CLASS 1 LASER PRODUCT. Label is located on the outside of the CD-

ROM/DVD-ROM drive with the following wordings:

CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT WARNING: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturers instructions. Explosionsgefahr bei unsachgemen Austausch der Batterie. Ersatz nur durch denselben oder einem vom Hersteller empfohlenem hnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers. WARNING: Your notebook contains a Ni-MH or Li-Ion battery pack. There is a risk of fire and chemical burn if the battery pack is handled improperly. Do not disassemble, crush, puncture, short external contact, dispose of in water or fire, or expose it to temperature higher than 60C. Page A-4 Users Guide Appendix A WARNING: Handle the battery pack very carefully. Avoid touching the metal leads on the connector of the battery case. CAUTION: Use only approved AC Adapter with your notebook. Using the wrong type of AC Adapter may cause serious damage to your notebook. CAUTION: The AC Adapter can accept a line voltage ranging from 100V to 240V and is compatible with most international power sources. If you are unsure whether your power source is compatible, please contact the local dealer for assistance. CAUTION: To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. CAUTION: For Continued Protection Against Risk of Fire, Replace Only with same Type and Rating of Fuse. CAUTION: If the computer is not sold to German area, please use only the local recognized power supply cords that are recommended by the manufacturer. Page A-5 Appendix A User's Guide A.2 Agency Notice Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected. Consult the dealer or an experienced radio or television technician for help. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by the manufacturer responsible for compliance may void the users authority to operate the equipment. Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain compliance with FCC Rules and Regulations. FCC RF Radiation Exposure Statement This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 0f 20 centimeters between the radiator and your body. Page A-6 Users Guide Appendix A USA and Canada Safety Requirements And Notices The FCC with its action in ET Docket 93-62 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. The Intel PRO/Wireless LAN MiniPCI Adapter products meet the Human Exposure limits found in OET Bulletin 65, 2001, and ANSI/IEEE C95.1, 1992. Proper operation of this radio according to the instructions found in this manual will result in exposure substantially below the FCCs recommended limits. The following safety precautions should be observed:

Do not touch or move antenna while the unit is transmitting or receiving. Do not hold any component containing the radio such that the antenna is very close or touching any exposed parts of the body, especially the face or eyes, while transmitting. Do not operate the radio or attempt to transmit data unless the antenna is connected; if not, the radio may be damaged. Use in specific environments:

The use of wireless devices in hazardous locations is limited by the constraints posed by the safety directors of such environments. The use of wireless devices on airplanes is governed by the Federal Aviation Administration (FAA). The use of wireless devices in hospitals is restricted to the limits set forth by each hospital. Antenna use:

In order to comply with FCC RF exposure limits, low gain integrated antennas should be located at a minimum distance of 20 cm (8 inches) or more from the body of all persons. High-gain, wall-mount, or mast-mount antennas are designed to be professionally installed and should be located at a minimum distance of 30 cm (12 inches) or more from body of all persons. Please contact your professional installer, VAR, or antenna manufacturer for proper installation requirements. Explosive Device Proximity Warning Warning: Do not operate a portable transmitter (such as a wireless network device) near unshielded blasting caps or in an explosive environment unless the device has been modified to be qualified for such use. Use On Aircraft Caution Caution: Regulations of the FCC and FAA prohibit airborne operation of radio-frequency wireless devices because their signals could interfere with critical aircraft instruments. Page A-7 User's Guide Appendix A Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Avis Canadien Cet appareil numerque de la classe B respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada. Canada Radio Frequency Interference Requirements This Class B digital apparatus complies with Canadian ICES-003, Issue 2, and RSS-210, Issue 4 (Dec. 2000). To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Cet appareil numrique de la classe B est conforme la norme NMB-003, No. 2, et CNR-

210, No. 4 (Dec. 2000). Pour empcher que cet appareil cause du brouillage au service faisant lobjet dune licence, il doit tre utiliz lintrieur et devrait tre plac loin des fentres afin de fournir un cran de blindage maximal. Si le matriel (ou son antenne dmission) est install lextrieur, il doit faire lobjet dune licence. European Union Product with the CE Marking comply with the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community and if this product has telecommunication functionality, the R&TTE Directive (1999/5/EC). Compliance with these directives implies conformity to the following European Norms (in parentheses are the equivalent international standards and regulations):

EN55022 (CISPR 22) Electromagnetic Interference EN55024 (IEC61000-4-2,3,4,5,6,8,11) Electromagnetic Immunity EN61000-3-2 (IEC61000-3-2)-Power Line Harmonics EN61000-3-3 (IEC61000-3-3)-Power Line Flicker EN60950 (IEC60950) Product Safety For devices with built-in wireless equipment, the following additional standards apply:

ETSI301489-17: General Emissions for Radio Equipment EN60950: Safety Notice Page A-8 Users Guide Appendix A ETSI300328-2: Technical Requirements for Radio Equipment CE Caution: Due to the fact that the frequencies used by 802.11b wireless LAN devices may not yet be harmonized in all countries, 802.11b products are designed for use only in specific countries or regions, and are not allowed to be operated in countries or regions other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries or regions for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country or region of use. And deviation from permissible settings and restrictions in the country or region of use could be an infringement of local law and may be punished as such. Japanese Notice DGT Statement Page A-9 Appendix A User's Guide U.S. Regulations Governing the Use of Modems This equipment complies with Part 68 of the FCC Rules. On this equipment is a label that contains, among other information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone company. If your telephone equipment harms the telephone network, the Telephone Company may discontinue your service temporarily. If possible, they will notify in advance. But, if advance notice is not practical, you will be notified as soon as possible. You will be informed of your right to file a compliant with the FCC. Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect proper operation of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. The FCC prohibits this equipment to be connected to party lines or coin-telephone service. In the event that this equipment should fail to operate properly, disconnect the equipment from the phone line to determine if it is causing the problem. If the problem is with the equipment, discontinue use and contact your dealer or vendor. The FCC also requires the transmitter of a FAX transmission be properly identified (per FCC Rules Part 68, Sec 68.381 (C) (3)). Japanese Modem Notice U.K. Modem Compliance Information This modem is approved by the secretary of state at the Department of Trade and Industry for connection to a single exchange line of the public switched telephone network run by certain licensed public telecommunication operators or system connected there to (Direct exchange lines only, not shared service or 1-1 carrier systems). Page A-10 Users Guide Appendix A This modem is also suitable for connection to Private Automatic Branch Exchange (PABX), which return secondary proceeding indication. If this modem is to be used with a PBX which has extension wiring owned by BT, connection of the modem the PBX can only be carried out by BT; or by the authorized maintainer of the PBX unless the authorized maintainer has been given 14 days written notice that the connection is to be made by another person; and that period of notification has expired. This modem is suitable for use only on telephone lines proved with Loop Disconnect or Multi-Frequency Dialing Facilities. Users of this modem are advised that the approval is for connection to the PSTN via the telephone line interface supplied with it. Connection of a modem to the PSTN by any other means will invalidate the approval. There is no guarantee of correct working in all circumstances. Any difficulties should be referred to your supplier. Some network operators require that intended users of their network request permission to connect and for the installation of an appropriate socket. The Ringer Equivalence Number (REN) of this modem is 1. REN is guide to the maximum number of apparatus that can simultaneously be connected to one telephone line. The REN value of each apparatus is added together, and should not exceed 4. Unless otherwise marked, a telephone is assumed to have a REN of 1. This modem is only approved for use of the following facilities:

Storage of telephone numbers for retrieval by a predator mined code. Automatic calling / automatic answering. Tone detection. Loud-speaking facility. This modem is not approved for connection to U.K./private speech-band services. This modem does not support an automatic re-dial function. Any other usage will invalidate the approval of your modem, if as a result, it then ceases to confirm to the standards against which approval was granted. The approval of this modem is invalidated if the apparatus is subject to modification in any material way not authorized by the BABT or if it is used with, or connected to external software that have not been formally accepted by BABT. Initial proceed indication detection. Page A-11 Users Guide Appendix B Appendix B- Environment ENVIRONMENT Operating Temperature Non-Operating Temperature Humidity Shock Vibration Warning: Don't expose your notebook to excessive heat or coldness (frost). Don't drop, spill fluids or open the exterior of the case. This can damage the notebook and void the warranty.

: 10C to 35C.

: -20C to 60C.

: 20% to 80% non-condensing.

: 5G operating, 60G non-operating.

: 3-200Hz @ 1.0G operating.

: 3-200Hz @ 1.5G non-operating. Page B-1