FCC ID: QDS-BRCM1073 802.11a/b/g/n WLAN + Bluetooth Card

OEM Installation Guidance Document For Broadcom 802.11a/b/g/n WLAN + Bluetooth Card BCM943241NG1630 FCC ID: QDS-BRCM1073; IC: 4324A-BRCM1073 Conditions on using BRCM regulatory approvals:

Customer must ensure that its product (the CUSTOMER Product) is electrically A. identical to Broadcoms reference designs. Customer acknowledges that any modifications to Broadcoms reference designs may invalidate regulatory approvals in relation to the CUSTOMER Product, or may necessitate notifications to the relevant regulatory authorities. Customer is responsible for ensuring that antennas used with the product are of B. the same type, with same or lower gains as approved and providing antenna reports to Broadcom. Customer is responsible for regression testing to accommodate changes to C. Broadcoms reference designs, new antennas, and portable RF exposure safety testing/approvals. Appropriate labels must be affixed to the CUSTOMER Product that comply with D. applicable regulations in all respects. E. product that contains the text as required by applicable law. Without limitation of the foregoing, an example (for illustration purposes only) of possible text to include is set forth below:

A users manual or instruction manual must be included with the customer 1. USAFederal Communications Commission (FCC) FCC COMPLIANCE STATEMENT:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INFORMATION TO USER:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

Page 1 of 9 OEM Installation Guidance Document For Broadcom 802.11a/b/g/n WLAN + Bluetooth Card BCM943241NG1630 FCC ID: QDS-BRCM1073; IC: 4324A-BRCM1073

-Reorient or relocate the receiving antenna

-Increase the distance between the equipment and the receiver.

-Connect the equipment to outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. CAUTION: (this only applicable to 5GHz device) This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range. FCC requires this product to be used indoors for frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. System integrators must include the FCC ID on the end product. FCC Radio-Frequency Exposure & Approval Conditions:

1. Antennas must be installed in the display section of Netbook/notebook/laptop computer to provide at least 20cm separation distance from the transmitting antenna to the body of user during normal operating condition. 2. Transmitting antenna(s) can only be installed at the display section of computer. When this device is installed other than notebook computers, at least 20 cm separation distance shall be maintained between the transmitting antenna(s) to the body of user or nearby person. 3. The antenna(s) used for this transmitter must not be collocated or operating in conjunction with any other antenna or transmitter within a host device, except in accordance with FCC multi-transmitter product procedures. 4. Only those antennas with same type and lesser gain filed under this FCC ID number can be used with this device. 5. The regulatory label on the final system must include the statement: Contains FCC ID: QDS-BRCM1073 and/or IC: 4324A-BRCM1073 or using electronic labeling method as documented in KDB 784748. 6. The final system integrator must ensure there is no instruction provided in the user manual or customer documentation indicating how to install or remove the transmitter module except such device has implemented two-ways authentication between module and the host system. 7. The final host manual shall include the following regulatory statement:

Page 2 of 9 OEM Installation Guidance Document For Broadcom 802.11a/b/g/n WLAN + Bluetooth Card BCM943241NG1630 FCC ID: QDS-BRCM1073; IC: 4324A-BRCM1073 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna

-Increase the distance between the equipment and the receiver.

-Connect the equipment to outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2. Canada - Industry Canada (IC) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. French:

Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Lutilisation de ce dispositif est autorise seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l utilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. French:

Page 3 of 9 OEM Installation Guidance Document For Broadcom 802.11a/b/g/n WLAN + Bluetooth Card BCM943241NG1630 FCC ID: QDS-BRCM1073; IC: 4324A-BRCM1073 Sous la rglementation d'Industrie Canada, ce transmetteur radio ne peut fonctionner en utilisant une antenne d'un type et un maximum (ou moins) gain approuves pour l'metteur par Industrie Canada. Pour rduire le risque d'interfrence aux autres utilisateurs, le type d'antenne et son gain doivent tre choisis de manire que la puissance isotrope rayonne quivalente (PIRE) ne dpasse pas ce qui est ncessaire pour une communication russie. This radio transmitter, IC ID: 4324A-BRCM1073, has been approved by Industry Canada to operate with the onboard antenna or a detachable WLAN antenna with a maximum gain of 3.9dB/2.4GHz and 5.8dBi/5GHz. Any other detachable antennas, with a different type or having a gain greater than 3.9dB/2.4GHz and 5.8dBi/5GHz are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. French:

Cet metteur radio, IC ID: 4324A-BRCM1073, a t approuv par Industrie Canada pour fonctionner avec l'antenne intgre ou une antenne amovible PIFA avec un gain maximum de 3.9dBi/2.4GHz, 5.8dBi/5GHz. Toute autre antenne dtachable, avec un type diffrent ou ayant un gain suprieur 3.9dBi, 5.8dBi est strictement interdit pour une utilisation avec cet appareil. L'impdance d'antenne requise est de 50 ohms. Caution: (this only applicable to UNII device)

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and

(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.

(iv) Users should also be advised that high-power radars are allocated as primary users

(i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. French:

Le guide dutilisation des dispositifs pour rseaux locaux doit inclure des instructions prcises sur les restrictions susmentionnes, notamment :

(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

Page 4 of 9 OEM Installation Guidance Document For Broadcom 802.11a/b/g/n WLAN + Bluetooth Card BCM943241NG1630 FCC ID: QDS-BRCM1073; IC: 4324A-BRCM1073

(ii) le gain maximal dantenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-5 725 MHz doit se conformer la limite de p.i.r.e.;

(iii) le gain maximal dantenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se conformer la limite de p.i.r.e. spcifie pour lexploitation point point et non point point, selon le cas.

(iv) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Caution: Exposure to Radio Frequency Radiation. To comply with RSS 102 RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Pour se conformer aux exigences de conformit 102 RSS RF exposition, pour des configurations mobiles, une distance de sparation d'au moins 20 cm doit tre maintenue entre l'antenne de cet appareil et toutes les personnes. Cet appareil ne doit pas tre co-

localiss ou fonctionnant en conjonction avec une autre antenne ou transmetteur. System integrators must include the IC ID on the end product. 3. Europe - EU Restrictions This equipment needs to be marked with the throughout the European community. 0560 symbol and can be used Marking by the symbol indicates that usage restrictions apply. Information to be supplied to the users:

802.11a Restrictions:

- This product is for indoor use only when using channels 36, 40, 44, 48, 52, 56, 60, or 64 (5150 5350 MHz).

- DFS and TPC must remain enabled to ensure product compliance with EC regulations. Page 5 of 9 OEM Installation Guidance Document For Broadcom 802.11a/b/g/n WLAN + Bluetooth Card BCM943241NG1630 FCC ID: QDS-BRCM1073; IC: 4324A-BRCM1073

- To ensure compliance with local regulations, be sure to select the country in which the access point is installed.

- This product can be used as shown in the table below:

5 GHz wireless LAN Indoor Use IEEE 802.11a Only A, AND, B, CH, D, CY, CZ, DK, ES, EST, F, FIN, FL, FR, GB, GR, H, I, IRL, IS, L, LT, M, MC, N, NL, P, PL, RSM, S, SK, SLO, V Caution: Exposure to Radio Frequency Radiation. To comply with RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. Czech:

User's Manual in Czech language and a statement of conformity with Directive 1999/5/EC in Czech language must be enclosed to each product. France:

2.4GHz for Metropolitan France:

In all Metropolitan dpartements, wireless LAN frequencies can be used under the following conditions, either for public or private use:

Indoor use: maximum power (EIRP*) of 100 mW for the entire 2400-2483.5 MHz frequency band Outdoor use: maximum power (EIRP*) of 100 mW for the 2400-2454 MHz band and with maximum power (EIRP*) of 10 mW for the 2454-2483 MHz band Italy:

For private use, a general authorisation is required if WAS/RLANs are used outside own premises. For public use, a general authorisation is required Note for system integrators:

- The module is tested to comply with the requirement of the R&TTE Directive. System integrators are responsible for compliance of the final device with the R&TTE Directive. Page 6 of 9 OEM Installation Guidance Document For Broadcom 802.11a/b/g/n WLAN + Bluetooth Card BCM943241NG1630 FCC ID: QDS-BRCM1073; IC: 4324A-BRCM1073

- Packaging: CE Marking must also be on the outer packaging of the product. The outer packaging must also provide an indication as to where the device is intended to be used and OR conversely, where there may be restrictions for use. 4. Taiwan - NCC Statement to be included in the user guide Statement- For general products Additional Statement - For 5G Band products 5.25G ~5.35G Translation:

Article 12 Without permission, any company, firm or user shall not alter the frequency, increase the power, or change the characteristics and functions of the original design of the certified lower power frequency electric machinery. Article 14 The application of low power frequency electric machineries shall not affect the navigation safety nor interfere a legal communication, if an interference is found, the service will be suspended until improvement is made and the interference no longer exists. The foregoing legal communication refers to the wireless telecommunication operated according to the telecommunications laws and regulations. The low power frequency electric machinery should be able to tolerate the interference of the electric wave radiation electric machineries and equipments for legal communications or industrial and scientific applications. Radio devices using 5.25-5.35GHz bands are restricted to indoor use only. Appendix:

(ID):

Page 7 of 9 OEM Installation Guidance Document For Broadcom 802.11a/b/g/n WLAN + Bluetooth Card BCM943241NG1630 FCC ID: QDS-BRCM1073; IC: 4324A-BRCM1073 CCXXxxLPyyyZz

,, CCXXxxLPyyyZz . 5. Korea Include the following statement either on the label or in the User Guide.

6. Argentina The current approval is in the name of Broadcoms local representative. It may be necessary to obtain regulatory approval in the name of the local distributor or importer. We suggest manufacturers check with their local distributors and importers in Argentina. 7. Brazil - Anatel Before using Broadcom Anatel approvals, 1. PC- OEM must make arrangement for its local offices or distributors to provide maintenance, technical assistance or replace any faulty products sold in Brazil. 2. All warranty services will be provided by the distributors or PC-OEM sales support in Brazil. An official agreement stating warranty responsibilities must be signed and made available to Broadcom. Interference statement to be included in the Users Guide

"Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio."

Translation:

"This equipment operates in secondary character. It can be affected by harmful interference. However, it cannot cause interference to systems operating in primary character."

Page 8 of 9 OEM Installation Guidance Document For Broadcom 802.11a/b/g/n WLAN + Bluetooth Card BCM943241NG1630 FCC ID: QDS-BRCM1073; IC: 4324A-BRCM1073 8. South Africa ICASA PC-OEMs must make arrangement for importers to supply spare parts and carry out repairs in South Africa. 9. Indonesia POSTEL, Kenya CCK, Nepal - NTA PC-OEMs must make arrangement for importers to provide product warranty and after sales services. 10. Japan MIC Radio devices using 5.15-5.35GHz bands are restricted to indoor use only. 11. Mexico PC-OEMs must make arrangement for importers to provide User Manual in Spanish in Mexico. The User Manual must feature the following mandatory statement:

La operacin de este equipo est sujeta a las siguientes dos condiciones:

(1) es posible que este equipo o dispositivo no cause interferencia prejudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. Translation:

The operation of this device is subject to the following two conditions:

(1) this equipment or device must not cause harmful interference and

(2) this equipment or device must accept any interference, including interference which could otherwise cause its undesired operation. 12. CB Certifications PC-OEMs must provide User Guides in the language suitable for the countries when shipping products to countries listed in the CB reports. Page 9 of 9

Date: June 3, 2013 Subject: Letter of Authorization to Use Broadcom Regulatory Approvals Letter of Authorization To: Customers Name (Customer) BROADCOM CORPORATION 190 Mathilda Place Sunnyvale, CA 94806 Phone: 408-543-3300 Fax: 408-543-3399 Subject to CUSTOMERs agreement with the terms of this letter, Broadcom Corporation (Broadcom) hereby authorizes CUSTOMER to use the Broadcom regulatory approvals described in Exhibit 1 and the test reports to the extent permitted by law. CUSTOMERs authorization to use such approvals and test reports are expressly conditioned upon CUSTOMERs compliance with all applicable laws and any conditions set forth in Exhibit 2, and may be revoked by Broadcom at any time in the event of any violation by CUSTOMER of such conditions or laws. CUSTOMER may not modify the configuration of the product in any manner that would change critical regulatory parameters or in any way that would violate the approved certification. CUSTOMER may not distribute any tools/applications that could modify the configuration of the product in any manner that would change critical regulatory parameters or in any way that would violate the approved certification. CUSTOMER must provide adequate means of software version verification to ensure that no un-authorized software updates can be used by the end user. CUSTOMER agrees to indemnify, defend and hold harmless Broadcom and its affiliates from and against any liabilities, actions, losses, judgments, payments made in settlement, costs, suits, proceedings, demands or claims from third parties incurred by Broadcom or any affiliate of Broadcom resulting from CUSTOMERs failure to comply with any conditions set forth in Exhibit 2 or any applicable laws. This Letter of Authorization is valid only for the following Broadcom product in countries listed in Exhibit 1. Product Name:

Model Name: BCMXXXXX This Letter of Authorization shall be governed by the laws of the State of California, without reference to its conflict of law principles, and is subject to the non-exclusive jurisdiction of the courts located therein. This authorization may be extended or withdrawn at any time, at the discretion of Broadcom Corporation. Please indicate your agreement with the terms of this Letter of Authorization by signing below and returning a copy to me. Best Regards, Daniel Lawless Director of Engineering, Systems Operations Broadcom Corp Tel: 408-922-5870 Email: dlawless@broadcom.com Acknowledged and agreed:

Name:

Title:

LEGAL_US_E # 80799546.1 Page 1of 10 EXHIBIT 1 Broadcom Radio Regulatory Approval Country List

[PLEASE REVIEW AND CONFIRM]

LEGAL_US_E # 80799546.1 Page 2 of 11 EXHIBIT 2 Conditions Applicable to Letter of Authorization

LEGAL_US_E # 80799546.1 Page 3 of 11

OEM Installation Guidance Document For Broadcom 802.11a/b/g/n WLAN + Bluetooth Card, BCM943241NG1630 FCC ID: QDS-BRCM1073; IC: 4324A-BRCM1073 Conditions on using BRCM regulatory approvals:

Customer must ensure that its product (the CUSTOMER Product) is electrically OEM must inform Broadcom of any changes which may require Class I or Class A. identical to Broadcoms product. Customer acknowledges that any modifications to Broadcoms product may invalidate regulatory approvals in relation to the CUSTOMER Product, or may necessitate notifications to the relevant regulatory authorities. B. II permissive changes. Any substituted antenna and RF cable assemblies must be approved by Broadcom in order to maintain compliance. C. applicable regulations in all respects. D. product that contains the text as required by applicable law. Without limitation of the foregoing, an example (for illustration purposes only) of possible text to include is set forth below:

1. USAFederal Communications Commission (FCC) A users manual or instruction manual must be included with the customer Appropriate labels must be affixed to the CUSTOMER Product that comply with FCC COMPLIANCE STATEMENT:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INFORMATION TO USER:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna

-Increase the distance between the equipment and the receiver.

-Connect the equipment to outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. Page 1 of 9 OEM Installation Guidance Document For Broadcom 802.11a/b/g/n WLAN + Bluetooth Card, BCM943241NG1630 FCC ID: QDS-BRCM1073; IC: 4324A-BRCM1073 Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. CAUTION: (this only applicable to 5GHz device) This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range. FCC requires this product to be used indoors for frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. System integrators must include the FCC ID on the end product. FCC Radio-Frequency Exposure & Approval Conditions:

1. Antennas must be installed in the display section or underneath the keyboard in Netbook/notebook/laptop/tablet computers to provide at least 5mm separation distance from the transmitting antenna to the body of user , or any other person during normal operating condition.

-For portable applications, the WLAN antennas used must be the same type of antennas as the original Equipment Authorization.

- For standalone SAR testing, the antenna is mounted on lossless foam material for testing. In order to use Broadcom modular approval, PCOEMs must install antennas with nonconductive materials surrounding the antenna. 2. The antenna(s) used for this transmitter must not be collocated or operating in conjunction with any other antenna or transmitter within a host device, except in accordance with FCC multi-transmitter product procedures. Please contact Broadcom for instructions. 3. The regulatory label on the final system must include the statement: Contains FCC ID: QDS-BRCM1073 and IC: 4324A-BRCM1073 or using electronic labeling method as documented in KDB 784748. 4. The final system integrator must ensure there is no instruction provided in the user manual or customer documentation indicating how to install or remove the transmitter module except such device has implemented two-ways authentication between module and the host system. Page 2 of 9 OEM Installation Guidance Document For Broadcom 802.11a/b/g/n WLAN + Bluetooth Card, BCM943241NG1630 FCC ID: QDS-BRCM1073; IC: 4324A-BRCM1073 5. The final host manual shall include the following regulatory statement:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna

-Increase the distance between the equipment and the receiver.

-Connect the equipment to outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2. Canada - Industry Canada (IC) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. French:

Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Lutilisation de ce dispositif est autorise seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l utilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. For PORTABLE applications, the WLAN antennas used must be the same type of antennas as the original Equipment Authorization. Page 3 of 9 OEM Installation Guidance Document For Broadcom 802.11a/b/g/n WLAN + Bluetooth Card, BCM943241NG1630 FCC ID: QDS-BRCM1073; IC: 4324A-BRCM1073 Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. French:

Pour les applications portables, les antennes WLAN utiliss doivent tre du mme type d'antennes que l'autorisation d'quipement d'origine Sous la rglementation d'Industrie Canada, ce transmetteur radio ne peut fonctionner en utilisant une antenne d'un type et un maximum (ou moins) gain approuves pour l'metteur par Industrie Canada. Pour rduire le risque d'interfrence aux autres utilisateurs, le type d'antenne et son gain doivent tre choisis de manire que la puissance isotrope rayonne quivalente (PIRE) ne dpasse pas ce qui est ncessaire pour une communication russie. This radio transmitter, IC ID: 4324A-BRCM1073, has been approved by Industry Canada in the mobile configuration to operate with the onboard antenna or a detachable WLAN antenna with a maximum gain of 3.9dB/2.4GHz and 5.8dBi/5GHz. Any other detachable antennas, with a different type or having a gain greater than 3.9dB/2.4GHz and 5.8dBi/5GHz are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. French:

Cet metteur radio, IC ID: 4324A-BRCM1073, a t approuv par Industrie Canada pour fonctionner avec l'antenne intgre ou une antenne amovible PIFA avec un gain maximum de 3.9dBi/2.4GHz, 5.8dBi/5GHz. Toute autre antenne dtachable, avec un type diffrent ou ayant un gain suprieur 3.9dBi, 5.8dBi est strictement interdit pour une utilisation avec cet appareil. L'impdance d'antenne requise est de 50 ohms. Caution: (this only applicable to UNII device)

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and

(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. Page 4 of 9 OEM Installation Guidance Document For Broadcom 802.11a/b/g/n WLAN + Bluetooth Card, BCM943241NG1630 FCC ID: QDS-BRCM1073; IC: 4324A-BRCM1073 Caution: Exposure to Radio Frequency Radiation. To comply with RSS 102 RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Pour se conformer aux exigences de conformit 102 RSS RF exposition, pour des configurations mobiles, une distance de sparation d'au moins 20 cm doit tre maintenue entre l'antenne de cet appareil et toutes les personnes. Cet appareil ne doit pas tre co-

localiss ou fonctionnant en conjonction avec une autre antenne ou transmetteur.System integrators must include the IC ID on the end product. Industry Canada user statements should be provided in both English and French, at the time each product is offered for sale or lease in Canada. For portable configurations, antennas must be installed in the display section or underneath the keyboard in Netbook/notebook/laptop/tablet computers to provide at least 5mm separation distance from the transmitting antenna to the body of user, or any other person during normal operating condition. Pour les configurations portables, les antennes doivent tre installes dans la section d'affichage ou sous le clavier netbook / notebook / ordinateur portable / tablette ordinateurs pour fournir au moins 5 mm distance de sparation entre l'antenne d'mission sur le corps de l'utilisateur, ou toute autre personne au cours de fonctionnement normal . 3. Europe - EU Restrictions This equipment needs to be marked with the throughout the European community. 0560 symbol and can be used Marking by the symbol indicates that usage restrictions apply. Information to be supplied to the users:

802.11a Restrictions:

- This product is for indoor use only when using channels 36, 40, 44, 48, 52, 56, 60, or 64 (5150 5350 MHz).

- DFS and TPC must remain enabled to ensure product compliance with EC regulations.

- To ensure compliance with local regulations, be sure to select the country in which the access point is installed. Page 5 of 9 OEM Installation Guidance Document For Broadcom 802.11a/b/g/n WLAN + Bluetooth Card, BCM943241NG1630 FCC ID: QDS-BRCM1073; IC: 4324A-BRCM1073

- This product can be used as shown in the table below:

5 GHz wireless LAN Indoor Use IEEE 802.11a Only A, AND, B, CH, D, CY, CZ, DK, ES, EST, F, FIN, FL, FR, GB, GR, H, I, IRL, IS, L, LT, M, MC, N, NL, P, PL, RSM, S, SK, SLO, V Caution: Exposure to Radio Frequency Radiation. To comply with RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. Czech:

User's Manual in Czech language and a statement of conformity with Directive 1999/5/EC in Czech language must be enclosed to each product. France (Removed after July 1, 2012):

2.4GHz for Metropolitan France:

In all Metropolitan dpartements, wireless LAN frequencies can be used under the following conditions, either for public or private use:

Indoor use: maximum power (EIRP*) of 100 mW for the entire 2400-2483.5 MHz frequency band Outdoor use: maximum power (EIRP*) of 100 mW for the 2400-2454 MHz band and with maximum power (EIRP*) of 10 mW for the 2454-2483 MHz band Italy:

For private use, a general authorisation is required if WAS/RLANs are used outside own premises. For public use, a general authorisation is required Note for system integrators:

- The module is tested to comply with the requirement of the R&TTE Directive. System integrators are responsible for compliance of the final device with the R&TTE Directive.

- Packaging: CE Marking must also be on the outer packaging of the product. The outer packaging must also provide an indication as to where the device is intended to be used and OR conversely, where there may be restrictions for use. 4. Taiwan - NCC Statement to be included in the user guide Page 6 of 9 OEM Installation Guidance Document For Broadcom 802.11a/b/g/n WLAN + Bluetooth Card, BCM943241NG1630 FCC ID: QDS-BRCM1073; IC: 4324A-BRCM1073 Statement- For general products Additional Statement - For 5G Band products 5.25G ~5.35G Translation:

Article 12 Without permission, any company, firm or user shall not alter the frequency, increase the power, or change the characteristics and functions of the original design of the certified lower power frequency electric machinery. Article 14 The application of low power frequency electric machineries shall not affect the navigation safety nor interfere a legal communication, if an interference is found, the service will be suspended until improvement is made and the interference no longer exists. The foregoing legal communication refers to the wireless telecommunication operated according to the telecommunications laws and regulations. The low power frequency electric machinery should be able to tolerate the interference of the electric wave radiation electric machineries and equipments for legal communications or industrial and scientific applications. Radio devices using 5.25-5.35GHz bands are restricted to indoor use only. Appendix:

(ID):

CCXXxxLPyyyZz

,, Page 7 of 9 OEM Installation Guidance Document For Broadcom 802.11a/b/g/n WLAN + Bluetooth Card, BCM943241NG1630 FCC ID: QDS-BRCM1073; IC: 4324A-BRCM1073 CCXXxxLPyyyZz . 5. Korea Include the following statement either on the label or in the User Guide.

6. Argentina The current approval is in the name of Broadcoms local representative. It may be necessary to obtain regulatory approval in the name of the local distributor or importer. We suggest manufacturers check with their local distributors and importers in Argentina. 7. Brazil - Anatel Before using Broadcom Anatel approvals, 1. PC- OEM must make arrangement for its local offices or distributors to provide maintenance, technical assistance or replace any faulty products sold in Brazil. 2. All warranty services will be provided by the distributors or PC-OEM sales support in Brazil. An official agreement stating warranty responsibilities must be signed and made available to Broadcom. Interference statement to be included in the Users Guide

"Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio."

Translation:

"This equipment operates in secondary character. It can be affected by harmful interference. However, it cannot cause interference to systems operating in primary character."

8. South Africa ICASA PC-OEMs must make arrangement for importers to supply spare parts and carry out repairs in South Africa. Page 8 of 9 OEM Installation Guidance Document For Broadcom 802.11a/b/g/n WLAN + Bluetooth Card, BCM943241NG1630 FCC ID: QDS-BRCM1073; IC: 4324A-BRCM1073 9. Indonesia POSTEL, Kenya CCK, Nepal - NTA PC-OEMs must make arrangement for importers to provide product warranty and after sales services. 10. Japan MIC Radio devices using 5.15-5.35GHz bands are restricted to indoor use only. 11. Mexico PC-OEMs must make arrangement for importers to provide User Manual in Spanish in Mexico. The User Manual must feature the following mandatory statement:

La operacin de este equipo est sujeta a las siguientes dos condiciones:

(1) es posible que este equipo o dispositivo no cause interferencia prejudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. Translation:

The operation of this device is subject to the following two conditions:

(1) this equipment or device must not cause harmful interference and

(2) this equipment or device must accept any interference, including interference which could otherwise cause its undesired operation. 12. CB Certifications PC-OEMs must provide User Guides in the language suitable for the countries when shipping products to countries listed in the CB reports. 13. Moldova- Labeling to be included Proper Marking must be included on each certified unit shipping into Moldova, Page 9 of 9

Introduction: Broadcom BCM943241NG1630 PCI-E Mini Card User's Guide Before you begin Things you should know BCM943241NG1630 network Before you begin Obtain the following information from your network administrator (if you are a home user, obtain this information from the person that installed your wireless access point):

l Network names (SSID) of the specific wireless networks that you want to connect to. l WEP (Wired Equivalent Privacy) key information (if any) for the networks you want to connect to. l For Microsoft Windows networking, your customer name and workgroup name. l For your network account, your user name and password. l Your IP address (if not using a DHCP server) Things you should know When you start your computer, your Broadcom BCM943241NG1630 PCI-E Mini card detects certain wireless networks that are within range. Before you can connect to these and other wireless networks, you must configure a profile for each network using the information you obtained from your network administrator. WEP is a security protocol for wireless local area networks (defined in the IEEE 802.11g standard) that encrypts data sent over radio waves. The use of the WEP key is optional and can be enabled or disabled. If the network you are connecting to has enabled WEP, you must also enable WEP in the network profile and set the WEP key to match the WEP key used by the network. Otherwise, you cannot connect to the network. Broadcom BCM943241NG1630 network The Broadcom BCM943241NG1630 solution allows you to make a wireless connection to a network, as illustrated below. Back to top Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide Back to Contents Page Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide Overview Utility Components Overview The Broadcom Wireless Utility enables you to do the following network tasks:

l Manage your wireless networks and create network connection profiles (Wireless Networks tab) l Connect to available networks (utility icon in notification area) l Get information about the network status and signal and noise of your network connection (Link Status tab) l View current and accumulated statistics (Statistics tab) l Find out which broadcasting networks are in range and search for nonbroadcasting networks (Site Monitor tab) l Run tests on the wireless network adapter (Diagnostics tab) l Get date and version information about the utility, and software, hardware, and location details about your wireless network adapter (Information tab) l Manually add or delete trusted servers and enable the manual acceptance or rejection of auto-

provisioning and A-ID group changes (Wireless Networks tab) l Manually import EAP-FAST PACs (Wireless Networks tab) In the utility, you can open Wireless Network Wizard to connect to a basic network or create an ad hoc network, or you can open the Wireless Network Connection Settings tool to connect to an advanced network. To do any of the other tasks, click the tab that is associated with the described task. To start using the utility, right-click the utility icon If the icon is not available, open Broadcom Wireless Utility in Control Panel. in the notification area, and then click Open Utility. NOTE: The utility icon may not appear exactly as shown here. See "Table 1. Signal Strength Indicated by the Broadcom Wireless Utility Icon."

Utility Components Utility components include the utility icon in the notification area, the six utility tabs, and Wireless Network Connection Settings. file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (1 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide Utility Icon To do any of the following tasks or operations, right-click the utility icon, and then click the appropriate item. l Open the on-line Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide

(Help Files) l Open About WLAN Card Utility to view links to Broadcom and Broadcom Customer Support websites and to view the version and date of the utility (About) l Hide the utility icon (Hide Tray Icon) l Disable or enable the radio (Disable/Enable Radio) l Connect to any of the networks for which you have created a connection profile and are within range (Connect To) l Open the utility to the Wireless Networks tab (Open Utility) l Open the utility to the Link Status tab to view information about the connection (Status) l Display a log of your wireless network events (Display Log) Wireless Networks Tab The Wireless Networks tab has tools that enable you to do the following:

l Use the utility to manage your wireless networks l Add a network connection profile l Edit or remove a network connection profile l Change the order in which profiles are listed under Preferred network connections l Connect to any listed network without changing its order in the list l Disable or enable the radio (Disable/Enable Radio) l Show or hide the utility icon in the notification area l Choose which type of network to access l Lock or unlock a preferred network connection profile l Save your wireless network connection profiles as a WPN file l Import a WPN file l Manually add or delete trusted servers and enable the manual acceptance or rejection of auto-

provisioning and A-ID group changes l Manually import EAP-FAST PACS On the Add menu, you can use either the wireless network wizard that is available from Broadcom Wireless Utility (see Connecting to a Basic Network or Creating an Ad Hoc Network Using the Wireless Network Wizard") or the utility (see "Connecting to an Advanced Network Using the Broadcom Wireless Utility") to add a network connection profile. To use the utility to manage your wireless networks, select the Let this tool manage your wireless networks check box. To add a network connection profile, click the Add arrow, and then click either Use Wizard (basic network) or Use Utility (advanced network). To edit or remove a network connection profile, right-click the network name, and then click either Edit or Remove. To change the order in which profiles are listed under Preferred network connections, click the network name, and then click either the up arrow or down arrow. To connect to any listed network without changing its order in the list, right-click the network name, and then click Connect. file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (2 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide To disable the radio, clear the Enable radio check box. To enable the radio, select the Enable radio check box. To hide the utility icon utility icon check box.

, clear the Show utility icon check box. To show the icon, select the Show To choose the type of network to access, click the Options arrow, and then click Advanced. To lock or unlock a preferred network connection profile, right-click anywhere in the row that lists the network name, and then click Lock or Unlock, as appropriate. NOTE: You must have system or administrator rights to be able to lock or unlock a profile. To save your wireless network connection profiles to a WPN file, click the Options arrow, and then click Export (see "Saving Preferred Network Connection Settings to a File" in "Connecting to an Advanced Network Using the Broadcom Wireless Utility."

To import a WPN file, click the Options arrow, and then click Import (see "Importing a Preferred Network Connection Profiles File" in "Connecting to an Advanced Network Using the Broadcom Wireless Utility."

Click Apply or OK after you change any of the settings for the change to take effect. file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (3 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide For networks that use the EAP-FAST authentication method, the Wireless WLAN Card Utility automatically adds trusted servers to the trust list and accepts auto-provisioning and AID (A-ID) group changes by default. The utility also enables you to import a Protected Access Credential (PAC). From the utility, you can also manually add or delete trusted servers, enable the manual acceptance or rejection of auto-

provisioning and A-ID group changes, or import or delete PACS, as described in the following instructions. In general, you should use the default settings. Therefore, check with the network administrator before you make any changes. To manually add a trusted server to the trust list 1. Open Broadcom Wireless Utility. 2. From the Wireless Networks tab, click Options, point to Cisco Compatible Extensions, and then click Administrator Settings. 3. Click Add. 4. Type the A-ID friendly name of the trusted server in the space provided, and then click OK. To delete a trusted server from the trust list file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (4 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide 1. Open Broadcom Wireless Utility. 2. From the Wireless Networks tab, click Options, point to Cisco Compatible Extensions, and then click Administrator Settings. 3. In the Trust list (A-ID), click the name of the trusted server you want to delete, and then click Delete. To change the default settings for administering Cisco Compatible Extensions 1. Open Broadcom Wireless Utility. 2. From the Wireless Networks tab, click Options, point to Cisco Compatible Extensions, and then click Administrator Settings. 3. Clear the Disable auto-provision prompt check box to enable manual acceptance or rejection. 4. Clear the Disable A-ID group change prompt check box to enable manual acceptance or 5. Select the Auto-provision PAC only once check box to auto-provision a Protected Access rejection. Credential (PAC) only once. To import or remove an EAP-FAST PAC 1. Open Broadcom Wireless Utility. 2. From the Wireless Networks tab, click Options, point to Cisco Compatible Extensions, and 3. To import a PAC: in Protected Access Credentials, click Add, and then follow the on-screen then click Manage PACs. instructions. NOTE: The PAC is password protected, so you must know the password to be able to import the PAC.

-or-

To remove a PAC: click anywhere in the row that lists the PAC, and then click Remove. Link Status Network status and signal and noise information about your network connection is displayed on the Link Status tab. NOTES:

l For IEEE 802.11n connections, speed is indicated by an MCS value. l Radio Stream information is provided only for IEEE 802.11n connections. l Click anywhere in the Signal & noise history box to change the type of history being displayed. Successive clicks change the type from both signal and noise, to noise only, to signal only, and back to both signal and noise. file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (5 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide The status of your network connection is also indicated by the appearance of the utility icon number and color of the radio waves indicates the strength or weakness of the signal (see Table 1. Signal Strength Indicated by the Broadcom Wireless Utility Icon for details). The To view the network name (SSID), speed, signal strength rating, connection status, and the client IP address of the network connection, move your mouse pointer over the utility icon. NOTE: On computers running Windows XP, you also can view the SSID, speed, signal strength rating, and connection status by moving your mouse pointer over the Windows Wireless Network Connection icon in the notification area. Table 1. Signal Strength Indicated by the Broadcom Wireless Utility Icon file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (6 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide Icon Appearance Indicated Received Signal Strength The signal strength is very good or excellent. The signal strength is weak. See Troubleshooting for suggested action. No signal is being received. See Troubleshooting for probable causes and suggested action. The radio is disabled or switched off. See Troubleshooting for suggested action. Statistics On the Statistics tab under Current, the following current statistics are shown:

l Network name (SSID) l Connection time l Packets sent l Packets received l Sent packets lost l Received packets lost l Total packets lost (%) Under Accumulated, the following accumulated statistics are shown:

l Packets sent l Packets received l Sent packets lost l Received packets lost file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (7 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide Site Monitor Basic Site Monitor On the Site Monitor tab, the basic Site Monitor displays information about wireless routers/APs and ad hoc networks that are within range. To sort the list, click the column heading that shows the characteristic you want to sort by. For example, to sort by signal strength, click Signal . To view information about a particular wireless router/AP or ad hoc network, click anywhere in the row that lists the wireless router/AP or ad hoc network. The network information is shown under Selected Network. To view or change the network connection settings for a particular wireless router/AP or ad hoc network, right-click anywhere in the row that lists the wireless router/AP or ad hoc network, and then click Editif you have not yet created a network connection profile for that particular wireless router/AP or ad hoc network and want to do so, click Add . To see the information elements for a listed AP or ad hoc network, right-click anywhere in the row that lists the AP or ad hoc network, and then click Show Information Elements. file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (8 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide NOTES:

l Nonbroadcasting networks are labeled (nonbroadcasting) under Network Name. l The network performance may be degraded while Site Monitor is displaying nonbroadcasting APs to which you are not currently connected. l The symbols under AP Band indicate IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, or IEEE 802.11n operation. To see more detailed information about a particular wireless router/AP or ad hoc network, click anywhere in the row that lists the wireless router/AP or ad hoc network, and then click Advanced. Advanced Site Monitor To save the activity log to a file, click the Options arrow, and then click Start Log. file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (9 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide You can adjust the time interval between scans by clicking the Options arrow, and then clicking either one of the preset values or clicking Customize to specify a different time interval. NOTE: The network performance may be degraded while Site Monitor is displaying nonbroadcasting networks to which you are not currently connected. To view detailed network information for a single nonbroadcasting network, type the network name in the Look for box, and then click Find. To reset the site monitor to the broadcasting networks, click Clear. Diagnostics On the Diagnostics tab, you can run a number of tests to determine if your wireless network adapter is functioning properly. Select the tests you want to run, and then click Run. For information about an individual test, look under Information before you click Run. To see the test results, look under Information after you click Run. NOTE: The network connection is lost when you run the tests. When the test run is over, your network connection is automatically reestablished. Also, you can view a log of your wireless network events. To do so, click Log. Examples of wireless network events that are logged include:

file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (10 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide l Initiation of user session l Connecting to a network l Disconnecting from current network l Authentication mode being used l Driver status l Supplicant status l New wireless device available l Initializing wireless state machine l Wireless utility is managing this adapter l Wireless utility is not managing this adapter If your Broadcom 802.11 Network Adapter fails any of the diagnostics tests, go to http://www.broadcom. com/ for technical support. Information file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (11 of 12)4/25/2006 1:57:41 PM Using the Broadcom Wireless Utility: Broadcom AirForce 54g and Intensi-fi Wireless Network Adapter User Guide The following information is displayed on the Information tab:

l Software details l Hardware details l Location details (shows the country for which the driver is installed and the channels supported for that location) Wireless Network Connection Settings The Wireless Network Connection Settings component is intended for use by advanced users or network administrators. You can use Wireless Network Connection Settings to create a connection profile for an advanced infrastructure network, a basic infrastructure network, or an ad hoc network (see " Connecting to an Advanced Network Using the Broadcom Wireless Utility"). Back to Contents Page file:///P|/User%20Manuals/WLANCard-UM302_LaLa/HTML/utility.htm (12 of 12)4/25/2006 1:57:41 PM Using the Broadcom BT Utility: Quick Start Guide Step 1: Installing the Software NOTE: This installation is required before you insert the module into the USB port of your computer. 1. Insert the Bluetooth USB Module installation compact disc (CD) into the CD-ROM or DVD drive of your computer. 2. If the Main Menu screen appears automatically, select Install software and click OK. If the Main Menu screen does not appear automatically, click Start, click Run, type x:\setup.exe (where x is the CD-ROM or DVD drive letter of your computer), and click OK. 3. Click Next, click Finish, and then restart your computer. 4. Right-click the Bluetooth icon in the taskbar notification area (system tray) and click Start Using Bluetooth. Follow the instructions provided by the Initial Bluetooth Configuration Wizard. Step 2: Inserting the Module Make sure that the Bluetooth USB Module is properly inserted inside your computer. If you started at Step 1: Installing the Software The Found New Hardware Wizard detects and installs the device. When the installation is finished, you are ready to begin using the Bluetooth features of this computer. If you skipped Step 1: Installing the Software, you are ready to begin using the Bluetooth features of this computer. NOTE: Before you begin, however, please review the Bluetooth USB Module Users Guide. This document provides important information and instructions that will help you do the things you want to do with your Bluetooth enabled computer. Glossary Authentication A Bluetooth security feature that is used to verify identity; it requires a Bluetooth PIN Code from the remote device. Authorization A Yes-or-No Bluetooth security feature that requires operator intervention to avoid having the connection time out and fail. Bluetooth device Bluetooth enabled hardware such as a computer, printer, fax, mouse, keyboard, cell phone, headset, or PDA. Regulatory Statements for BCM943241NG1630 Please refer to Broadcom OEM installation guide separation distance o