FCC ID: QDS-BRCM1058 802.11a/bg/n WLAN + Bluetooth PCI-E Mini Card

ThinkPad Regulatory Notice About this manual This manual contains regulatory information for the following ThinkPad products. ThinkPad S431 ThinkPad S531 Read first regulatory information Read this document before using your computer. This computer complies with the radio frequency and safety standards of any country or region in which it has been approved for wireless use. Install and use your computer according to the following instructions. If your computer contains a wireless WAN adapter, be sure to also read ThinkPad Regulatory Notice for the Wireless WAN Adapter, included with your computer. The latest Regulatory Notice has been uploaded on the Web site. To refer to it, go to http://www.lenovo.com/think/support, and then click Guides & Manuals. Veuillez lire le prsent document avant d'utiliser votre ordinateur. Cet ordinateur est conforme aux normes de frquence radio et de scurit de tous les pays ou rgions dans lesquels son utilisation sans fil a t homologue. Installez et utilisez l'ordinateur en respectant les instructions qui suivent. Si votre ordinateur contient une carte de rseau tendu (WAN) sans fil, veillez lire galement la consigne rglementaire ThinkPad Regulatory Notice for the Wireless WAN Adapter, fournie avec votre ordinateur. La version la plus rcente de la Notice relative la rglementation a t charge sur le site Web. Pour la consulter, accdez http://www.lenovo.com/think/support, puis sur Guides & Manuals. USA Federal Communications Commission (FCC) I. Approved wireless devices This section presents the FCC ID and model number of each wireless device. i) User installable wireless LAN/Bluetooth combo adapter ThinkPad S431 and ThinkPad S531 1 FCC ID: QDS-BRCM1058 (Model: BCM943228HMB) FCC ID: PD92230BNHU (Model: 2230BNHMW) FCC ID: QDS-BRCM1063 (Model: BCM943142HM) Notes:

The PCI Express Mini Cards incorporate two functions: wireless LAN and Bluetooth. PCI Express Mini Cards for a wireless LAN marketed in the USA and Canada do not support or function in the extended channels (12ch, 13ch). II. User installable wireless LAN/Bluetooth combo adapter i) Use of the wireless LAN/Bluetooth combo adapter If no integrated PCI Express Mini Card has been preinstalled in your computer, you can install one, provided by Lenovo as an option. Plug the wireless option adapter into the PCI Express Mini Card slot. For the installation procedure, see Replacing a wireless LAN card in User Guide. Attention: The computer contains an authentication mechanism. If you install an unauthorized PCI Express Mini Card that is not approved for use in your computer, the computer will not start, but only displays an error message and emits audible beeps. ii) FCC ID location There is no FCC ID for the PCI Express Mini Card shown on the enclosure of your computer. Instead you will find an indicator pointing to the location of the FCC ID on the bottom of your computer. The FCC ID is affixed on the approved adapter installed in the PCI Express Mini Card slot, and the FCC ID is visible prior to installation. For the location of the FCC ID indicator and the slot, see FCC ID and IC Certification number label in User Guide. iii) FCC RF Exposure compliance The total radiated energy from the antennas connected to one of the PCI Express Mini Cards conforms to the FCC limit of the SAR (Specific Absorption Rate) requirement regarding 47 CFR Part 2 section 1093. The transmission antennas for the PCI Express Mini Card are located in the LCD cover. See Location of the UltraConnectTM wireless antennas in User Guide. iv) Radio Frequency interference requirements Each device has been tested and found to comply with the limits for a Class B digital device pursuant to FCC Part 15 Subpart B. Refer to Electronic emission notices on page 6. 2 When you use a wireless LAN adapter in the 802.11 a/n transmission mode:

Each device is restricted to indoor use due to its operation in the 5150 to 5250 MHz frequency range. FCC requires these products to be used indoors for the frequency range 5150 to 5250 MHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5250 to 5350 MHz and 5650 to 5850 MHz bands. These radar stations can cause interference with and/or damage this device. III. Simultaneous use of RF transmitters Your computer is approved for simultaneous use of the approved wireless WAN adapter, and one of the approved wireless LAN adapter or wireless LAN/Bluetooth combo adapter. For a list of those transmitters, refer to I. Approved wireless devices on page 1 and ThinkPad Regulatory Notice for the Wireless WAN Adapter. Make sure of the following conditions when you use any other external RF option device:

1. When you use any other RF option device, you are requested to confirm that the device conforms to the RF Safety requirement and is approved to use for your computer. 2. You must follow the RF Safety instructions of the RF option device that are included in the user manual of the RF option device. 3. If the RF option device is prohibited to use in conjunction with another transmitters, you must turn off all other wireless features in your computer. Canada Industry Canada (IC) IC Certification number I. Approved wireless devices This section presents the IC Certification and model number of each wireless device. i) User installable wireless LAN/Bluetooth combo adapter ThinkPad S431 and ThinkPad S531 IC: 4324A-BRCM1058 (Model: BCM943228HMB) IC: 1000M-2230BNHU (Model: 2230BNHMW) IC: 4324A-BRCM1063 (Model: BCM943142HM) 3 Notes:

The PCI Express Mini Cards incorporate two functions: wireless LAN and Bluetooth. PCI Express Mini Cards for a wireless LAN marketed in the USA and Canada do not support or function in the extended channels (12ch, 13ch). II. User installable wireless LAN/Bluetooth combo adapter There is no certification number of Industry Canada for the PCI Express Mini Card shown on the enclosure of your computer. Instead you will find an indicator pointing to the location of the IC Certification number on the bottom of your computer. The IC certification number is affixed on the approved adapter installed in the PCI Express Mini Card slot, and the IC Certification number is visible prior to installation. For the location of the IC Certification number indicator and the slot, see FCC ID and IC Certification number label in User Guide. Attention: The computer contains an authentication mechanism. You can install or remove each wireless adapter by yourself. If you install an unauthorized wireless adapter that is not approved for use in the computer, the computer will not start, but only displays an error message and emits audible beeps. III. Low power license-exempt radiocommunication devices

(RSS-210) Operation is subject to the following two conditions:

1. This device may not cause interference, and 2. this device must accept any interference, including interference that may cause undesired operation of the device. The transmitter devices have been designed to operate with the antennas integrated in the computer, and having a maximum gain of within 3 dBi. The maximum antenna gain permitted for devices in the 5250-5350 MHz, 5470-5725 MHz, and 5725-5825 MHz bands complies with the e.i.r.p. limit in section A9.2 of RSS-210. When you use a wireless LAN adapter in the 802.11 a/n transmission mode:

The devices for the band 51505250 MHz are only for indoor usage to reduce potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users (meaning they have priority) of 52505350 MHz and 56505850 MHz and these radars could cause interference and/or damage to LELAN (Licence-Exempt Local Area Network) devices. 4 IV. Exposure of humans to RF fields (RSS-102) The computers employ low gain integral antennas that do not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's Web site at http://www.hc-sc.gc.ca/

The radiated energy from the antennas connected to the wireless adapters conforms to the IC limit of the RF exposure requirement regarding IC RSS-102, Issue 4 clause 4.1. Numro d'homologation IC I. Priphriques sans fil homologus Cette section prsente le numro d'homologation IC et le numro de modle de chaque priphrique sans fil. i) Module sans fil installable par l'utilisateur ThinkPad S431 and ThinkPad S531 IC: 4324A-BRCM1058 (Model: BCM943228HMB) IC: 1000M-2230BNHU (Model: 2230BNHMW) IC: 4324A-BRCM1063 (Model: BCM943142HM) Remarque:

Les cartes mini-PCI Express intgrent deux fonctions : rseau local sans fil et Bluetooth. Les cartes de rseau local sans fil Express mini-PCI commercialises aux Etats-Unis et au Canada ne prennent pas en charge les canaux tendus (12ch, 13ch) et ne fonctionnent donc pas sur de tels canaux. II. Module sans fil installable par l'utilisateur Le botier de votre ordinateur ne comporte pas de numro d'homologation IC

(Industry Canada) pour la carte mini-PCI Express; mais sous votre ordinateur, vous trouverez un indicateur pointant vers l'emplacement du numro d'homologation IC. Pour connatre l'emplacement du numro d'homologation IC, consultez la section correspondante dans User Guide. Le numro d'homologation IC figure sur la carte homologue installe dans le logement pour carte mini-PCI Express et est visible avant l'installation. Pour savoir o se trouve cet emplacement, consultez la section correspondante dans User Guide. Attention: L'ordinateur contient un mcanisme d'authentification. Vous pouvez installer ou dsinstaller tout dispositif sans fil. Si vous installez une carte sans fil qui n'est pas homologue dans votre ordinateur, l'ordinateur ne dmarrera pas mais affichera un message d'erreur et gnrera des bips sonores. 5 III. Remarque relative aux appareils de communication radio de faible puissance sans licence (CNR-210) Le fonctionnement de ce type d'appareil est soumis aux deux conditions suivantes:

1. Cet appareil ne doit pas perturber les communications radio, et 2. cet appareil doit supporter toute perturbation, y compris les perturbations qui pourraient provoquer son dysfonctionnement. Les priphriques d'mission sont conus pour fonctionner avec des antennes intgres l'ordinateur et ayant un gain maximal de moins de 3 dBi. Le gain d'antenne maximal pour les priphriques dans les bandes de frquence 5250-5350 MHz, 5470-5725 MHz, et 5725-5825 MHz est conforme la limite p.i.r.e nonce dans la section A9.2 de la CNR-210. Lorsque vous utilisez la carte pour rseau local sans fil en mode de transmission 802.11 a/n:

Tout appareil destin la bande 5150-5250 MHz devra tre exclusivement utilis en intrieur afin de rduire les risques de perturbations lectromagntiques gnantes sur les systmes de satellite mobile dans un mme canal. Les radars forte puissance sont dsigns comme les utilisateurs principaux

(c'est--dire qu'ils sont prioritaires) des bandes 5250-5350 MHz et 5650-5850 MHz. Ils peuvent provoquer des perturbations lectromagntiques sur les appareils de type LELAN (rseau de communication local sans licence) ou les endommager. IV. Exposition des tres humains aux champs radiolectriques

(RF) (CNR-102) L'ordinateur utilise des antennes intgrales faible gain qui n'mettent pas un champ lectromagntique suprieur aux normes imposes par le Ministre de la sant canadien pour la population. Consultez le Safety Code 6 sur le site Web du Ministre de la sant canadien l'adresse http://www.hc-sc.gc.ca/

L'nergie mise par les antennes relies aux cartes sans fil respecte la limite d'exposition aux radiofrquences telle que dfinie par Industrie Canada dans la clause 4.1 du document CNR-102, version 4. Electronic emission notices Federal Communications Commission (FCC) Declaration of Conformity Model: BCM943228HMB 6 Model: 2230BNHMW Model: BCM943142HM Note: The wireless LAN/Bluetooth combo adapters underwent certification process for the FCC Part 15 Subpart B compliance under each respective FCC ID number. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which Increase the separation between the equipment and receiver. the receiver is connected. Consult an authorized dealer or service representative for help. Lenovo is not responsible for any radio or television interference caused by unauthorized changes or modifications to this equipment. Unauthorized change or modifications could avoid the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party:

Lenovo (United States) Incorporated 1009 Think Place-Building One Morrisville, NC 27560 Telephone: 1-919-294-5900 Industry Canada Class B Emission Compliance Statement This Class B digital apparatus complies with Canadian ICES-003. 7 Avis de conformit la rglementation d'Industrie Canada Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both:

Lenovo ThinkPad UltraConnect Other company, product, and service names may be trademarks or service marks of others. 8 First Edition (June 2013) Copyright Lenovo 2013. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration GSA contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925. Printed in China

(1P) P/N: SP40A25328

*1PSP40A25328*

Lenovo Miix 2 11 User Guide Read the safety notices and important tips in the included manuals before using your computer.

Notes Before using the product, be sure to read Lenovo Safety and General Information Guide rst. Some instructions in this guide may assume that you are using Windows 8.1. If you are using another Windows operating system, some operations may be slightly different. If you are using other operating systems, some operations may not apply to you. The features described in this guide are common to most models. Some features may not be available on your computer or your computer may include features that are not described in this user guide. The illustrations in this manual may differ from the actual product. Please refer to the actual product. Regulatory Notice The Regulatory Notice provides information about the radio frequency and safety standards. Be sure to read it before using wireless devices on your computer. To refer to it, go to http://www.lenovo.com, click Support, and then click Users guides and manuals. First Edition (December 2013) Copyright Lenovo 2013. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General Services Administration GSA contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925. Contents Chapter 1. Getting to know your computer...................................................................................... 1 Top view..........................................................................................................................................................1 Left-side view .................................................................................................................................................3 Right view.......................................................................................................................................................5 Front view.......................................................................................................................................................5 Rear view ........................................................................................................................................................5 Bottom view....................................................................................................................................................6 Dock top view ................................................................................................................................................7 Dock left view.................................................................................................................................................8 Dock right view..............................................................................................................................................8 Chapter 2. Starting to use Windows 8.............................................................................................. 9 Configuring the operating system for the first time.................................................................................9 Operating system interfaces.........................................................................................................................9 The charms....................................................................................................................................................10 Putting the computer to sleep or shutting it down.................................................................................12 Touch screen operation...............................................................................................................................14 Connecting to wireless LAN ......................................................................................................................18 Help and support.........................................................................................................................................19 Chapter 3. Recovery system ........................................................................................................... 20 Chapter 4. Troubleshooting............................................................................................................. 21 Frequently asked questions........................................................................................................................21 Troubleshooting...........................................................................................................................................22 Trademarks ....................................................................................................................................... 25 i Chapter 1. Getting to know your computer Top view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

3 2 2 3 Note: The dashed areas indicate parts that are not visible externally. 4 5 a b c d Front camera Wireless WAN antennas (on select models) Wireless LAN antennas Windows button e Multi-touch screen Use the camera for video communication or taking photos. Connect to a wireless WAN adapter to send and receive wireless radio signals. Connect to a wireless LAN adapter to send and receive wireless radio signals. Press this button to:

Toggle between the current view and the Start screen.

-or-

Wake up the computer from sleep mode. Functions as the visual display as well as one of the two primary input methods. Note: For details, see Touch screen operation on page 14. 1 Chapter 1. Getting to know your computer Screen orientation You can rotate the display panel to your preferred orientation. The orientation of the display automatically changes (alternating between portrait and landscape modes) depending on how you hold it. 2 Chapter 1. Getting to know your computer Left-side view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

1 2 3 4 5 6 7 8 Connects to the AC power adapter or USB devices. USB port Notes:

Use only the power cord and adapter shipped with the computer. Output of the USB power cord is 20 V for charging function and 5 V for all other purposes. The power cord does not support linking two computers together. Attention:

The combined power adapter and power cord are intended for use with this product only. Use of the combined power adapter and power cord with an unapproved device can cause damage. You are responsible for any problems caused by their misuse. Connects to headsets. a



b Combo audio jack Notes:

The combo audio jack does not support conventional microphones. The recording function might not be supported if third-party headphones or headsets are connected, due to different industry standards. c Micro HDMI port d e f g h Micro SIM card slot

(on select models) Micro SD card slot Speaker Power button Battery status indicator Indicator status On (white) On (amber) Blinking (white) Blinking slowly (amber) Connects to devices with HDMI inputs, such as a TV, or an external display. Accepts a SIM card (not supplied). Accepts a micro SD card (not supplied). Provides audio output. Press this button to turn on the computer. Charge status Meaning Charging Discharging Discharging Charging Charging The batterys charge is greater than 80%. The batterys charge is greater than 20%. The batterys charge is less than 20%, but above 5%. The batterys charge is less than 80%, but above 20%. The batterys charge is less than 20%, but above 5%. Blinking quickly (amber) Discharging/Charging The batterys charge is less than 5%. Off

--

3 The computer is off. Chapter 1. Getting to know your computer Using a micro SD card (not supplied) Your computer supports micro Secure Digital (SD) cards. Notes:

Insert only one card into the slot at a time. This card reader does not support SDIO devices (e.g., SDIO Bluetooth, etc.). Inserting a card 1 Open the card slot cover. 2 Slide the card in until it clicks into place. Removing a card 1 Push the card in until you hear a click. 2 Gently pull the memory card out of the slot. 3 Close the card slot cover. Note: Before removing the memory card, disable it by using the Windows safely remove hardware and eject media utility to avoid data corruption. 4 Chapter 1. Getting to know your computer Right view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

1 2 a b Volume button Speaker Increases/Decreases volume level. Provides audio output. Front view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

1 a



Ventilation slots Dissipate internal heat. Attention:

Make sure that none of the ventilation slots are blocked or else overheating of the computer may occur. Rear view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

1 a Dock connector Connects the tablet to the dock. 5 Chapter 1. Getting to know your computer Bottom view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

1 a Rear Camera Use the camera for video communication or taking photos. 6 Chapter 1. Getting to know your computer Dock top view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

1 2 3 a b c Speaker Dock connector Keyboard Provides audio output. Connects the tablet to the dock. 7 Chapter 1. Getting to know your computer Dock left view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

1 aa aa USB port Note: Keyboard dock USB ports do not support the combined power cord and power adapter charging Connects to USB 2.0 devices. function. Dock right view - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

1 USB port Note: Keyboard dock USB ports do not support the combined power cord and power adapter charging Connects to USB 2.0 devices. function. 8 Chapter 2. Starting to use Windows 8 Configuring the operating system for the first time - - - - - - - - - - - - - - - -

You might need to configure the operating system when it is first used. The configuration process can include the procedures below:

Accepting the end user license agreement

Configuring the internet connection

Registering the operating system

Creating a user account Operating system interfaces - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Windows 8 comes with two main User Interfaces: the Start screen and the desktop. To switch from the Start screen to the desktop, do one of the following:

Select the desktop tile on the Start screen.

Press the Windows key (

To switch from the desktop to the Start screen, do one of the following:

) + D (located on the folio case).

Select Start from the charms.

Move the pointer to the lower-left corner and then select the Start screen thumbnail when it is displayed. Start screen Desktop 9 Chapter 2. Starting to use Windows 8 The charms - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

The five charms provide new and faster ways to perform many basic tasks, and are always available regardless of which app you are currently in. To display the charms, do one of the following:

Move the pointer to the upper-right or lower-right corner until the charms bar is displayed.

Use one finger to swipe in from the right edge of the screen until the charms bar is displayed.

Press the Windows key (

) + C (located on the folio case). Search charm The Search charm is a powerful new way to find whatever you are looking for, including apps, settings, and files. 10 Chapter 2. Starting to use Windows 8 Share charm The Share charm enables you to send links, photos, and more to your friends and social networks without leaving the app you are in. Start charm The Start charm is a way to go to the Start screen. Devices charm The Devices charm enables you to connect or send files to any external devices, such as digital cameras, TVs, or printers. Settings charm The Settings charm enables you to perform basic tasks, such as setting the volume or shutting down the computer. Also, you can get to the Control Panel through the Settings charm when using the desktop screen. 11 Chapter 2. Starting to use Windows 8 Putting the computer to sleep or shutting it down - - - - - - - - - - - - - - - - - - -

When you have finished working with your computer, you can put it to sleep or shut it down. Putting your computer to sleep If you will be away from your computer briefly, put the computer to sleep. When the computer is in sleep mode, you can quickly wake it to resume use, bypassing the startup process. To put the computer to sleep, do one of the following:

Press the Power button.

Open the charms and then select Settings Power Sleep. To wake the computer, do one of the following:

Press any key on the keyboard (located on the folio case).

Press the Power button.

Press the Windows button. 12 Chapter 2. Starting to use Windows 8 Shutting down the computer If you are not going to use your computer for a long time, shut it down. To shut down your computer:

1 Open the charms, and then select Settings

. 1 2 Select Power Shut down. 2 13 Chapter 2. Starting to use Windows 8 Touch screen operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

The display panel can accept inputs like a tablet, using the multi-touch screen, or like a traditional notebook computer, using the keyboard and touch pad. Multi-touch gestures You can touch the screen with one or more fingertips to perform a variety of tasks. Frequently used gestures Tasks performed Tap Tap once on an item. Performs an action, such as starting an app, opening a link, or performing a command. Similar to left-clicking with a mouse. Press and hold Press your finger down and leave it there for a moment. Enables you to see detailed information before selecting an action. Can also open a menu with more options. Similar to right-

clicking with a mouse. 14 Chapter 2. Starting to use Windows 8

(continued) Frequently used gestures Tasks performed Zoom Move two fingers together or apart while touching the screen. Zooms in and out on visual apps, such as pictures and maps. Can also jump to the beginning or end of a list. Rotate Place two or more fingers on an item and then turn your hand. Rotates an object (Note: Not all items can be rotated, depending upon the app.). Slide Drag your finger across the screen. Pans or scrolls through lists and pages. Can also move an object or be used to draw or write, depending upon the app. Similar to pressing and holding to pan and to scrolling with a mouse. 15 Chapter 2. Starting to use Windows 8

(continued) Frequently used gestures Tasks performed Swipe Start from any edge of the screen, then swipe inwards toward the center. Swiping down from the top edge or up from the bottom edge displays a task bar on the bottom of the screen with app commands, including save, edit, and delete. If you have an app currently open, you can also:

Swipe from the top edge to halfway down the screen without lifting your finger to dock that app on the left or right side of the screen. This enables you to keep two apps open simultaneously in a split-screen format.

Swipe from the top edge straight down to the bottom edge of the screen continuously without lifting your finger to close the currently open app. 16 Chapter 2. Starting to use Windows 8

(continued) Frequently used gestures Tasks performed Swiping in from the left edge can:

Bring in and open an app currently running in the background. If there is more than one currently open app, you can:

Swipe in from the left to bring in an app and, without lifting your finger, push that app quickly back off the left edge of the screen. This displays a list of the apps currently running in the background. Swiping in from the right edge of the screen displays the charms. 17 Chapter 2. Starting to use Windows 8 Connecting to wireless LAN - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Enabling wireless connection To confirm that Airplane mode is disabled, go to the desktop and check the notification area. If you see the wireless function is enabled. icon displayed on the lower right, then Airplane mode is on. Otherwise, Note: Airplane mode should be disabled by default. If Airplane mode is on, do one of the following to enable the wireless function:

Press F7 (

) to disable Airplane mode (located on the folio case).

Open the charms, select Settings to open the Network configuration page, and then toggle the Airplane mode switch to Off. Connecting to a wireless LAN After wireless has been enabled, the computer will scan for available wireless networks and display them in the wireless LAN network list. To connect to a wireless network, click the network name in the list, and then click Connect. Note: Some networks require a network security key or passphrase for connection. To connect to one of those networks, ask the network administrator or the Internet Service Provider (ISP) for the security key or passphrase. Note: Any downloading task will pause when you close the display panel (while using the folio case). 18 Chapter 2. Starting to use Windows 8 Help and support - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

If you have any problems using the operating system, see the Windows Help and Support file. To open the Windows Help and Support file, do one of the following:

Select the Settings charm. Select Help.

Press Fn + F1 (

) (located on the folio case). You can read the Windows Help and Support file on your computer. You can also get online help and support by clicking the link listed under More to explore. 19 Chapter 3. Recovery system Introduction Push-button reset is a built-in recovery tool that enables users to restore their operating system to its original state. This preserves their data and important customizations, without the need to back up their data in advance. The following Push-button reset features are available to users from multiple locations within Windows:

Refreshing the computer Fixes software problems by reinstalling the factory default configuration. This preserves the users data, important settings, and any Windows Store apps previously purchased from the Windows Store. Resetting the computer Prepares the computer for recycling or transfer of ownership. This reinstalls the factory default configuration and returns all user data and applications to the state of their original Out-of-Box Experience (OOBE). Using Push-button reset Push-button reset can be launched using one of the following methods:

Power button + Volume up button:

- Shut down the tablet and wait at least five seconds.

- Press and hold the volume up button (

) and then press the Power button (

), until the Novo Button Menu appears on the screen.

Windows PC setting

- Windows PC setting General Advanced startup select Restart now.

Settings charm:

- Select Power.

- Press and hold the Shift key while selecting Restart. For more instructions, see the Windows Help and Support file on your computer. 20 Chapter 4. Troubleshooting Frequently asked questions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

This section lists frequently asked questions by category. Finding information What safety precautions should I follow when using my computer?

The Lenovo Safety and General Information Guide which came with your computer contains safety precautions for using your computer. Read and follow all precautions during use. Where can I find the hardware specifications for my computer?

You can find hardware specifications for your computer on the printed flyers which came with your computer. Where can I find warranty information?

For the warranty applicable to your computer, including the warranty period and type of warranty service, see the Lenovo limited warranty flyer that came with your computer. Drivers Where can I find drivers for the various hardware devices of my computer?

You can download the latest device drivers from the Lenovo consumer support website. Getting help How can I contact the customer support center?

See Chapter 3. Getting help and service in the Lenovo Safety and General Information Guide. 21 Chapter 4. Troubleshooting Troubleshooting - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

If you do not find your problem here, see Chapter 1. The following section only describes problems that might negate the need to refer to the more comprehensive information in Chapter 1. Display problems When I turn on the computer, nothing appears on the screen. The screen goes blank while the computer is on.

If the screen is blank, make sure that:

- The AC power adapter is connected to the computer and the power cord is plugged into a working electrical outlet.

- The computer power is on. Press and hold the Power button for three seconds for confirmation.

- Press and hold the Power button for seven seconds to force shut down the computer. Then press the power button for three seconds to restart.

If these items are set correctly and the screen remains blank, have the computer serviced.

Your power management is enabled. Do one of the following to resume from sleep mode:

- Press any key on the keyboard (located on the folio case).

- Press the Power button.

- Press the Windows button. Sleep problems The critical low-battery error message appears, and the computer immediately turns off. The computer enters sleep mode immediately after Power-on.

The battery power is getting low. Connect the AC power adapter to the computer.

Make sure that:

- The battery is charged.

- The operating temperature is within the acceptable range. See Chapter 2. Use and care Information in the Lenovo Safety and General Information Guide. Note: If the battery is charged and the temperature is within range, do the following:

1 Press the Power button for three seconds to turn on the computer. 2 Press and hold the Power button for seven seconds to force shut down. 3 Press the Power button for three seconds again to restart. Then reset the computer with the Push-button reset recovery system. If the problem persists, have the computer serviced. 22 Chapter 4. Troubleshooting The computer does not return from sleep mode and the computer does not work.

If the computer does not return from sleep mode, it might be because the battery is depleted.

If your computer is in sleep mode, connect the AC power adapter to the computer. Then press the Windows button or the Power button.

If your computer is powered-off, connect the AC power adapter to the computer. Then press the Power button to resume operation. Note: If the system still does not return from sleep mode, your system has stopped responding, and you cannot turn off the computer; force shut down the computer (Unsaved data may be lost). To force shut down the computer, press and hold the Power button for seven seconds or more. If the computer still does not turn off, remove the AC power adapter. Display panel problems The screen is blank.

Do the following:

The screen is unreadable or distorted. Incorrect characters appear on the screen.

- If you are using the AC power adapter or the battery, press F12 (

) to make the screen brighter.

- Press the Power button to confirm if the computer is in sleep mode.

- If the problem persists, follow the solution in the next problem The screen is unreadable or distorted.

Make sure that the screen resolution and color quality are correctly set.

Is the operating system or programs installed correctly?

If they are installed and configured correctly, do the following:

1 Press the Power button for three seconds to turn on the computer. 2 Press and hold the Power button for seven seconds to force shut down. 3 Press the Power button for three seconds to restart. Then reset the computer with the Push-button reset recovery system. If the problem persists, have the computer serviced. Sound problems No sound can be heard from the speaker even when the volume is turned up.

Make sure that:

- The Mute function is off.

- The combo audio jack is not being used.

- Speakers are selected as the playback device. 23 Chapter 4. Troubleshooting Battery problems Your computer shuts down before the battery status icon shows it is empty.

-or-

Your computer operates after the battery status icon shows it is empty. A startup problem The Microsoft Windows operating system does not start. Recovery System problems Failure to restore system partition to factory default. Other problems Your computer does not respond.

Recharge the battery.

For details, see Recovery system on page 20.

The system partition (e.g. the partition size or the drive capacity of C) has been modified.

To turn off your computer, press and hold the Power button for seven seconds or more. If the computer still does not respond, remove the AC power adapter. 24 Trademarks Lenovo is a trademark or registered trademark of Lenovo in the United States, other countries, or both. Microsoft and Windows are trademarks of Microsoft Corporation in the United States, other countries, or both. 25 L e n o v o C h n a 2 0 1 3 i en-US Rev. AA00

Lenovo Miix 2 11 Regulatory Notice Lenovo regulatory notice for wireless adapters - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

This manual contains regulatory information for the following Lenovo product. Lenovo Miix 2 11 The following wireless module is supported on Lenovo Miix 2 11:

BCM943228HMB

AR5B22 Read first regulatory information Please read this document before you use the Lenovo computer. Lenovo computer complies with the radio frequency and safety standards of any country or region in which it has been approved for wireless use. You must install and use your computer in strict accordance with the instructions as described hereafter. Veuillez lire ce document avant dutiliser lordinateur Lenovo. Lordinateur Lenovo est conforme aux normes de scurit et de radiofrquence du pays ou de la rgion o son utilisation sans fil est agre. Vous devez installer et utiliser votre ordinateur en respectant scrupuleusement les instructions dcrites ci-aprs. 1 USA Federal Communications Commission (FCC) I. Factory preinstalled Wireless LAN and Bluetooth Combo module FCC ID: QDS-BRCM1058 (Model: BCM943228HMB)

FCC ID: PPD-AR5B22 (Model: AR5B22) Wireless LAN and Bluetooth Combo Card marketed in the USA and Canada do not support nor function in the extended channels (12ch, 13ch). i) The FCC RF Exposure compliance:

The radiated output power of the Wireless LAN and Bluetooth Combo Card authorized to use for the your Lenovo computer is far below the FCC radio frequency exposure limits. Nevertheless, it shall be used in such a manner that the potential for human contact during normal operation is minimized as follows:

Note: The transmission diversity function is implemented for this product. For WLAN card (Model:

BCM943228HMB, AR5B22) using Main and Auxiliary antennas for transmission in the IEEE 802.11 a/g/n transmission mode, radio frequency energy is not emitted simultaneously from both Main and Auxiliary antennas. One of the antennas is selected automatically or manually

(by users) to have good quality of radiocommunication (transmission diversity function). For WLAN card BCM943228HMB, AR5B22 in the IEEE 802.11 a/g/n, or MIMO (Multiple In Multiple Out ) transmission mode, the radio frequency energy is emitted from Main antenna. ii) FCC ID of wireless module:

On the bottom side of your Lenovo computer, you will find an indicator label of the format Contains Transmitter Module: FCC ID XXXX, where XXXX represents the FCC ID that corresponds to your preinstalled Wireless LAN and Bluetooth Combo module. II. Simultaneous use of RF transmitters Please make sure of the following conditions on use of wireless features:

1. When you use any other RF option device, all wireless features in your Lenovo computer are required to be turned off. 2. Users must follow the RF Safety instructions on wireless option devices that are included in the RF option device's user's manual. III. Radio Frequency interference requirements:

Each device has been tested and found to comply with the limits for a Class B digital device pursuant to FCC Part 15 Subpart B. Refer to Electronic emission notices on page 5. The models BCM943228HMB, AR5B22 underwent the certification process with each respective FCC ID number listed in I. Factory preinstalled Wireless LAN and Bluetooth Combo module on page 2. When you use a Wireless LAN and Bluetooth Combo module in the 802.11 a/n transmission mode:

Each device is restricted to indoor use due to its operation in the 5150 to 5250 MHz frequency range. FCC requires these products to be used indoors for the frequency range 5150 to 5250 MHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems.

High power radars are allocated as primary users of the 5250 to 5350 MHz and 5650 to 5850 MHz bands. These radar stations can cause interference with and/or damage this device. 2 Canada Industry Canada (IC) IC Certification number I) Factory preinstalled Wireless LAN and Bluetooth Combo modules:

IC: 4324A-BRCM1058 (Model: BCM943228HMB)

IC: 4104A-AR5B22 (Model: AR5B22) Wireless LAN and Bluetooth Combo Card marketed in the USA and Canada do not support nor function in the extended channels (12ch, 13ch). There is no certification number of Industry Canada for Mini PCI Express Card shown on the enclosure of your Lenovo computer. Instead you will find an indicator label pointing to the location of the IC Certification number on the bottom side of your Lenovo computer. This label will be of the format Contains Transmitter Module: Canada IC: XXXX, where XXXX represents the IC ID that corresponds to your preinstalled WLAN module. II) Low power license-exempt radiocommunication devices (RSS-210):

Operation is subject to the following two conditions:

1. This device may not cause interference, and 2. this device must accept any interference, including interference that may cause undesired operation of the device. The transmitter devices have been designed to operate with the antennas integrated in Lenovo computer, and having a maximum gain of within 3 dBi. III) Exposure of humans to RF fields (RSS-102):

Lenovo computers employ low gain integral antennas that do not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canadas Web site at www.hc-sc.gc.ca/rpb The radiated energy from the antennas connected to the wireless adapters conforms to the IC limit of the RF exposure requirement regarding IC RSS-102, Issue 4 clause 4.2. The maximum antenna gain permitted for devices in the 5250-5350 MHz, 5470-5725 MHz, and 5725-5825 MHz bands complies with the e.i.r.p. limit in section A9.2 of RSS-210. When you use a Wireless LAN and Bluetooth Combo module adapter in the 802.11 a/n transmission mode:

The devices for the band 5150-5250 MHz are only for indoor usage to reduce potential for harmful interference to co-channel Mobile Satellite systems.

High power radars are allocated as primary users (meaning they have priority) of 5250-

5350 MHz and 5650-5850 MHz bands and these radars could cause interference and/or damage to LELAN (Licence-Exempt Local Area Network) devices. 3 Numro dhomologation IC I) Modules combins Bluetooth et LAN sans fil prinstalls lusine:

IC: 4324A-BRCM1058 (Model: BCM943228HMB)

IC: 4104A-AR5B22 (Model: AR5B22) Les cartes de rseau local sans fil Express mini-PCI commercialises aux Etats-Unis et au Canada ne prennent pas en charge les canaux tendus (12ch, 13ch) et ne fonctionnent donc pas sur de tels canaux. Le botier de votre ordinateur Lenovo ne comporte pas de numro dhomologation IC (Industry Canada) pour la carte mini-PCI Express ; mais sous votre Lenovo, vous trouverez une tiquette indicatrice pointant vers lemplacement du numro dhomologation IC. Ltiquette se prsente sous la forme Contains Transmitter Module: Canada IC: XXXX o XXXX reprsente lID IC qui correspond au module WLAN prinstall. II) Remarque relative aux appareils de communication radio de faible puissance sans licence (CNR-210):

Le fonctionnement de ce type dappareil est soumis aux deux conditions suivantes:

1. Cet appareil ne doit pas perturber les communications radio, et 2. cet appareil doit supporter toute perturbation, y compris les perturbations qui pourraient provoquer son dysfonctionnement. Les priphriques dmission sont conus pour fonctionner avec des antennes intgres aux Lenovo et ayant un gain maximal de moins de 3 dBi. III) Exposition des tres humains aux champs radiolectriques (RF) (CNR-102):

Lordinateur Lenovo utilise des antennes intgrales faible gain qui nmettent pas un champ lectromagntique suprieur aux normes imposes par le Ministre de la sant canadien pour la population. Consultez le Safety Code 6 sur le site Web du Ministre de la sant canadien ladresse www.hc-sc.gc.ca/rpb. Lnergie mise par les antennes relies aux adaptateurs sans fil respecte la limite dexposition aux radiofrquences telle que dfinie par Industrie Canada dans la clause 4.2 du document CNR-102. Le gain d'antenne maximal autorispour les appareils dans les bandes de frquence 5250-

5350 MHz, 5470-5725 MHz et 5725-5825 MHz est conforme la limite p.i.r.e (puissance isotrope rayonne quivalente) dfinie dans la section A9.2 du CNR-210. Lorsque vous utilisez un adaptateur de module combin Bluetooth et LAN sans fil dans le mode de transmission 802.11 a/n:

Les appareils destins la bande 5150-5250 MHz devront tre exclusivement utillss en intrieur afin de rduire les risques de perturbations lectromagntiques gnantes sur les systmes de satellite mobile dans un mme canal.

Les radars forte puissance sont dsigns comme les utilisateurs principaux (c'est--dire qu'ils sont prioritaires) des bandes 5250-5350 MHz et. 5650-5850 MHz. lls peuvent provoquer des perturbations lectromagntiques sur les appareils de type LELAN (rseau de communication local sans licence) ou les endommager. 4 Electronic emission notices Federal Communications Commission (FCC) Declaration of Conformity

BCM943228HMB

AR5B22 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult an authorized dealer or service representative for help. Lenovo is not responsible for any radio or television interference caused by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party:

Lenovo (United States) Incorporated 1009 Think Place - Building One Morrisville, NC 27560 Telephone: 1-919-294-5900 Industry Canada Class B Emission Compliance Statement This Class B digital apparatus complies with Canadian ICES-003. Avis de conformit la rglementation dIndustrie Canada Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Trademarks Lenovo, the Lenovo logo are trademarks of Lenovo in the United States, other countries, or both. Other company, product, or service names may be trademarks or service marks of others. 5 L e n o v o C h n a 2 0 1 4 i

Aspire Notebook Series Quick Guide Product registration When using your product for the first time, it is recommended that you immediately register it. This will give you access to some useful benefits, such as:

Membership in the Acer community: receive promotions and participate in customer Faster service from our trained representatives. surveys. The latest news from Acer. Hurry and register, as other advantages await you!

How to register To register your Acer product, please visit www.acer.com. Select your country, click PRODUCT REGISTRATION and follow the simple instructions. You will also be asked to register your product during the setup process, or you can double-click the Registration icon on the desktop. After we receive your product registration, you will be sent a confirmation email with important data that you should keep in a safe place. Obtaining Acer accessories We are happy to inform you that Acer's warranty extension program and Notebook accessories are available online. Come and visit our online shop and find what you need at store.acer.com. The Acer store is being progressively rolled out, and, unfortunately may not be available in some regions. Please check back regularly to see when it will be available in your country. 2011. All Rights Reserved. Aspire Notebook Series Quick Guide Original Issue: 07/2011 Model number: __________________________________ Serial number: ___________________________________ Date of purchase: ________________________________ Place of purchase: ________________________________ Acer recommends... Productivity Software Work Great with Microsoft Office 2010 - Express your ideas, solve problems and simplify everyday projects with Office 2010. Photo editing - Easily edit and print your photos with Windows Live Photo Gallery. Then share them on Facebook, YouTube or Windows Live. Search & Decide with Bing - Find and organize the answers you need using Bing, so you can make faster, more informed decisions. 3 First things first We would like to thank you for making an Acer notebook your choice for meeting your mobile computing needs. E n g l i s h Your guides To help you use your Acer notebook, we have designed a set of guides:

First off, the setup poster helps you get started with setting up your computer. The Aspire Users Manual contains useful information applying to your new computer. It covers basic topics such as using the keyboard and audio, etc. The Quick Guide introduces you to the basic features and functions of your new computer. For more on how your computer can help you to be more productive, please refer to the Aspire Users Manual. This guide contains detailed information on such subjects as system utilities, data recovery, expansion options and troubleshooting. In addition it contains warranty information and the general regulations and safety notices for your notebook. It is available from your computer desktop; simply double-

click the Acer Users Manual icon. 4 h s i l g n E Your Acer notebook tour After setting up your computer as illustrated in the setup poster, let us show you around your new Acer notebook. Top view

1 2 3 4 5 Icon Item Display screen Power button /

indicator Microphone Keyboard Touchpad Description Also called Liquid-Crystal Display (LCD), displays computer output. Turns the computer on and off. Indicates the computer's power status. Internal microphone for sound recording. For entering data into your computer. Touch-sensitive pointing device. The lower left and right of the touchpad react like left and right selection buttons;

press down on either area to perform a left or right click. 5

6 7 Icon Item Description Power indicator Indicates the computers power status. Battery indicator Indicates the computers battery status. Charging: The light shows amber when the battery is charging. Fully charged: The light shows blue when in AC mode. Integrated webcam Web camera for video communication. E n g l i s h Rear view

1 2 3 Icon Item Description DC-in jack Connects to an AC adapter. HDMI port USB 2.0 ports Supports high-definition digital video connections. Connect to USB 2.0 devices (e.g., USB mouse, USB camera). Left view Icon

1 Item Headset/speaker jack Connects to audio devices (e.g., speakers, headphones) or a headset with microphone. Description 6 Right view h s i l g n E

1 Icon Item 2-in-1 card reader Description Accepts one Secure Digital (SD or SDHC) card or one MultiMediaCard

(MMC). Note: To remove the card, simply pull it from the slot. Base view

1 2 Icon Item Battery reset pinhole Speakers Description Insert a paperclip into the hole to reset the computer (simulates removing and reinstalling the battery). Deliver stereo audio output. Environment Temperature:

Humidity (non-condensing):

Operating: 20% to 80%

Non-operating: 20% to 80%

Operating: 5 C to 35 C Non-operating: -20 C to 65 C

REGULATORY INFORMATION PREVENTION OF HEARING LOSS

- Caution: Permanent hearing loss may occur if earphones or headphones are used at high volume for prolonged periods of time.

- A pleine puissance, lcoute prolonge du baladeur peut endommager loreille de lutilisateur. CAUTION when listening To protect your hearing, follow these instructions. Increase the volume gradually until you can hear clearly and comfortably.

- Do not increase the volume level after your ears have adjusted.

- Do not listen to music at high volumes for extended periods.

- Do not increase the volume to block out noisy surroundings.

- Decrease the volume if you cant hear people speaking near you. RADIO DEVICE REGULATORY NOTICE

- Note: Regulatory information below is for models with wireless LAN and/or Bluetooth only. Compliance accessories The accessories associated with this equipment are: shielded video cable when an external monitor is connected. These accessories are required to be used in order to ensure compliance with FCC rules. CALIFORNIA PROPOSITION 65 WARNING This product contains chemicals known to the State of California to cause cancer, birth defects, and/or other reproductive harm. For additional information regarding this product warning, go to www.gateway.com/prop65. 88 - Regulatory information MERCURY WARNING THE LAMP IN THIS DISPLAY CONTAINS MERCURY. DISPOSE ACCORDING TO LOCAL, STATE, AND FEDERAL LAW.

(JAPAN) VCCI WIRELESS ADAPTER REGULATORY INFORMATION USAFCC and FAA The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency(RF) electromagnetic energy emitted by FCC certified equipment. The wireless adapter meets the Human Exposurelimits found in OET Bulletin 65, supplement C, 2001, and ANSI/IEEE C95.1, 1992. Proper operation of this radioaccording to the instructions found in this manual will result in exposure substantially below the FCCsrecommended limits.

- The following safety precautions should be observed:

Do not touch or move antenna while the unit is transmitting or receiving.

- Do not hold any component containing the radio such that the antenna is very close or touching anyexposed parts of the body, especially the face or eyes, while transmitting.

- Do not operate the radio or attempt to transmit data unless the antenna is connected;

this behavior maycause damage to the radio. Regulatory information - 89 Use in specific environments:

- The use of wireless adapters in hazardous locations is limited by the constraints posed by the safetydirectors of such environments.

- The use of wireless adapters on airplanes is governed by the Federal Aviation Administration (FAA).

- The use of wireless adapters in hospitals is restricted to the limits set forth by each hospital. The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Explosive Device Proximity Warning Warning: Do not operate a portable transmitter (including this wireless adapter) near unshielded blastingcaps or in an explosive environment unless the transmitter has been modified to be qualified for such use Use On Aircraft Caution Caution: Regulations of the FCC and FAA prohibit airborne operation of radio-frequency wireless devices(wireless adapters) because their signals could interfere with critical interfere with critical aircraft instruments. The Wireless Adapter and Your Health The wireless adapter, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by the wireless adapter, however, is less than the electromagnetic energy emitted by other wireless devices such as mobile phones. The wireless adapter operates within the guidelines found in radio frequency safety standards and recommendations. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some 90 - Regulatory information situations or environments, the use of the wireless adapter may be restricted by the proprietor of the building or responsible representatives of the applicable organization. Examples of such situations may include:

- Using the wireless adapter on board airplanes, or

- Using the wireless adapter in any other environment where the risk of interference with other devices or services is perceived or identified as being harmful. If you are uncertain of the policy that applies to the use of wireless adapters in a specific organization or environment (an airport, for example), you are encouraged to ask for authorization to use the adapter before you turn it on. FCC Radio Frequency Interference Requirements (applied to machine supports 802.11a) This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz and 5.470 to 5.725 GHz frequency ranges. FCC requires this product to be used indoors for the frequency ranges 5.15 to 5.25 GHz and5.470 to 5.725 GHz to reduce the potential for harmful interference to co-channel mobile satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and /or damage this device. No configuration controls are provided for this wireless adapter allowing any change in the frequency of operations outside the FCC grant of authorization for U.S operation according to Part 15.407 of the FCC rules. USAFederal Communications Commission (FCC) This device complies with Part 15 of the FCC Rules. Operation of the device is subject to the following two conditions:

- This device may not cause harmful interference.

- This device must accept any interference that may cause undesired operation.

- This product does not contain any user serviceable components. Any unauthorized product changes or modifications will invalidate warranty and all applicable regulatory certifications and approvals, including authority to operate this device. Regulatory information - 91

(Notice for 5GHz) Operations in the 5.15-5.25GHz band are restricted to indoor usage only. (For 5GHz only)

- NOTE: The radiated output power of the adapter is far below the FCC radio frequency exposure limits. Nevertheless, the adapter should be used in such a manner that the potential for human contact during normal operation is minimized. To avoid the possibility of exceeding the FCC radio frequency exposure limits, you should keep a distance of at least 20cm between you (or any other person in the vicinity), or the minimum separation distance as specified by the FCC grant conditions, and the antenna that is built into the computer. Details of the authorized configurations can be found at http://www.fcc.gov/oet/ea/ by entering the FCC ID number on the device. Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If the equipment is not installed and used in accordance with the instructions, the equipment may cause harmful interference to radio communications. There is no guarantee, however, that such interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by taking one or more of the following measures:

- Reorient or relocate the receiving antenna of the equipment experiencing the interference. Increase the distance between the wireless adapter and the equipment experiencing the interference.

- Connect the computer with the wireless adapter to an outlet on a circuit different from that to which the equipment experiencing the interference is connected.

- Consult the dealer or an experienced radio/TV technician for help. 92 - Regulatory information Canada Industry Canada (IC) This device complies with RSS210 of Industry Canada. Cet appareil se conforme RSS210 de Canada d'Industrie. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Ce dispositif est conforme a la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prejudiciable, et (2) ce dispositif doit accepter tout brouillage recu, y compris un brouillage susceptible de provoquer un fonctionnement indesirable.

(Notice for 5GHz) Caution :

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and

(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.

(iv) Users should also be advised that high-power radars are allocated as primary users

(i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.

(RF exposure statement) Radiation Exposure Statement:

Regulatory information - 93 The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme a la norme NMB-003 du Canada.

"To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing."

Pour empcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit tre utilis a l'intrieur et devrait tre plac loin des fentres afin de fournir un cran de blindage maximal. Si le matriel (ou son antenne d'mission) est install l'extrieur, il doit faire l'objet d'une licence. European Union List of applicable countries This product must be used in strict accordance with the regulations and constraints in the country of use. For further information, contact the local office in the country of use. Please see http://ec.europa.eu/enterprise/rtte/implem.htm for the latest country list. List of National Codes THIS EQUIPMENT MAY BE OPERATED IN THE FOLLOWING COUNTRIES:

ISO 3166 2 letter code MT NT PL United Kingdom GB IS Iceland Liechtenstein LI ISO 3166 2 letter code DE GR HU ISO 3166 2 letter code AT BE CY Malta Netherlands Poland Germany Greece Hungary Austria Belgium Cyprus ISO 3166 2 letter code Country Country Country Country 94 - Regulatory information Country ISO 3166 2 letter code Country Czech Republic CZ DK Denmark EE Estonia Finland FI FR France Ireland Italy Latvia Lithuania Luxembourg ISO 3166 2 letter code IE IT LV LT LU Country Portugal Slovakia Slovenia Spain Sweden ISO 3166 2 letter code PT SK SL ES SE Country Norway Switzerland Bulgaria Romania Turkey ISO 3166 2 letter code NO CH BG RO TR The low band 5.15 -5.35 GHz is for indoor use only. This equipment complies with the essential requirements of the European Union directive 1999/5/EC. See Statements of European Union Compliance, and more details refer to the attached Declaration of Conformity. English esky [Czech]

Daansk [Danish]

Deutsch [German]

Eesti [Estonian]

Espaol [Spanish]

[Greek]

Franais [French]

Hereby, ACER INC., declares that this Radiolan is in compliance with the essential requirements and other rele vant provisionns of Directive 1999/5/EC. ACER INC. tmto prohlauje, e tento Radiolan je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 1999/5/ES. Undertegnede ACER INC. erklrer herved, at flgende udstyr Radio lan overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF. Hiermit erklrt ACER INC., dass sich das Gert Radiolan in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 1999/5/EG befindet. Kesolevaga kinnitab ACER INC. seadme Radiolan vastavust direktiivi 1999/5/E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. Por medio de la presente ACER INC. declara que el Radiolan cumplee con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/

CE. ACER INC. Radiolan 1999/5/ . Par la prsente ACER INC. dclare que l'appareil Radiolan est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Regulatory information - 95 slenska [Icelandic]

Itaaliano [Italian]

Latviski [Latvian]

Lietuvi [Lithuanian]

Malti [Maltese]

Magyar [Hungarian]

Nederlands [Dutch]

Norsk [Norwegiann]

Polski [Polish]

Portugus

[Portuguese]

Slovensko

[Slovenian]

Slovensky [Slovak]

Suomi [Finnish]

Svenska [Swedish]

Hr me lsir ACER INC. yfir v a Radiolan er samrmi vi grunnkrfur og arar krfur, sem gera r eru tilskipun 1999/5/EC. Con la presente ACER INC. dichiara che questo Radiolan conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Ar o ACER INC. deklar, ka Radiolan atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. iuo ACER INC. deklaruoja, kad is Radiolan atitinka esminius reikalavimus ir kitas 1999/5/

EB Direktyvos nuostatas. Hawnhekk, ACER INC., jiddikjara li dan Radiolan jikkonforma mal- ti ijiet essenzjali u ma provvedimenti o rajn relevanti li he mm fid-Dirrettiva 1999/5/EC. Alulrott, ACER INC. nyilatkozom, hogy a Radiolan megfelel a vonatkoz alapvet kvetelmnyeknek s az 1999/5/EC irnyelv egyb elrsainak. Hierbij verklaart ACER INC. dat het toeste l Radiolan in overeenstem ming is met de essentile eisen en de andere relevante bepalin gen van richtlijn 1999/5/EG. ACER INC. erklrer herved at utstyret Ra diolan er i samsvar med de grunnlegggende krav og vrige relevante krav i direktiv 1999/5/EF. Niniejszym ACER INC. owiadcza, e Radiolan jest zgodny z zasadniczymi wymogami oraz pozostaymi stosownymi postanowieniami Dyrektywy 1999/5/EC. ACER INC. declara que este Radiolan est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE. ACER INC. izjavlja, da je ta je Radiolan skladen z bistvenimi zahtevami in ostalimi relevantnimi doloili Direktive 1999/5/ES. ACER INC. tmto vyhlasuje, e Radiolan spa zkladn poiadavky a vetky prslun ustanovenia Smernice 1999/5/ES. ACER INC. vakuuttaa tten ett Radiolan tyyppinen laite on direktiivi n 1999/5/EY oleellisten vaatimusten ja sit koskevienn direktiivin muiden ehtojen mukainen. Hrmed intygar ACER INC. att denna Radiolan str I v erensstmme lse med de vsentliga egenskappskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG. 96 - Regulatory information France Products with 2.4GHz Wireless LAN Devices France L'utilisation de cet equipement (2.4GHz wireless LAN) est soumise certaines restrictions: cet equipement peut tre utilis l'interieur d'un batiment en utilisant toutes les frequences de 2400 a 2483.5MHz (Chaine 113). Pour une utilisation en environement exterieur, les frequences comprises entre 2400-2454 MHz peuvent tre utilis. Pour les dernires restrictions, voir http://www.art-telecom.fr. For 2.4GHz wireless LAN operation of this product, certain restrictions apply. This equipment may use the entire2400MHz to 2483.5MHz frequency band (channels 1 through 13) for indoor applications. For outdoor use, only 2400-2454 MHz frequency band may be used. For the latest requirements, see http://www.art-telecom.fr. Pour la France mtropolitaine 2.400 - 2.4835 GHz (Canaux 1 13) autoris en usage intrieur 2.400 -2.454 GHz (canaux 1 7) autoris en usage extrieur Pour la Guyane et la Runion 2.400 - 2.4835 GHz (Canaux 1 13) autoris en usage intrieur 2.420 - 2.4835 GHz (canaux 5 13) autoris en usage extrieur Pour tout le territoire Franais:

Seulement 5.15 -5.35 GHz autoris pour le 802.11a L'utilisation de cet equipement (2,4 GHz WLAN) est soumise certaines restrictions :

- La puissance maximale autorise en intrieur est de 100 mW pour 2400 - 2483,5 MHz.

- La puissance maximale autorise est de 100 mW en extrieur pour 2400 - 2454 MHz.

- La puissance maximale autorise est de 10 mW en extrieur, 2454 - 2483,5 MHz. Pour les dernires restrictions, voir http://www.art-telecom.fr. Regulatory information - 97 Italy The use of these equipments is regulated by:

1.D.L.gs 1.8.2003, n. 259, article 104 (activity subject to general authorization) for outdoor use and article 105 (free use) for indoor use, in both cases for private use. 2.D.M. 28.5.03, for supply to public of RLAN access to networks and telecom services. Luso degli apparati regolamentato da:

1.D.L.gs 1.8.2003, n. 259, articoli 104 (attivit soggette ad autorizzazione generale) se utilizzati al di fuori del proprio fondo e 105 (libero uso) se utilizzati entro il proprio fondo, in entrambi i casi per uso private. 2.D.M. 28.5.03, per la fornitura al pubblico dellaccesso R-LAN alle reti e ai servizi di telecomunicazioni. Belgium Dans le cas d'une utilisation prive, l'extrieur d'un btiment, au-dessus d'un espace public, aucun enregistrement n'est ncessaire pour une distance de moins de 300m. Pour une distance suprieure 300m un enregistrement auprs de l'IBPT est requise. Pour les enregistrements et licences, veuillez contacter l'IBPT. In geval van priv-gebruik, buiten een gebouw, op een openbare plaats, is geen registratie nodig, wanneer de afstand minder dan 300m is. Voor een afstand groter dan 300m is een registratie bij BIPT vereist. Voor registraties en licenties, gelieve BIPT te contacteren. Brazil Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio. Pakistan Pakistan Telecommunication Authority (PTA) Approved 98 - Regulatory information Morocco The operation of this product in the radio channel 2 (2417 MHz) is not authorized in the following cities: Agadir,Assa-Zag, Cabo Negro, Chaouen, Goulmima, Oujda, Tan Tan, Taourirt, Taroudant and Taza. The operation of this product in the radio channels 4, 5, 6 et 7 (2425 - 2442 MHz) is not authorized in thefollowing cities: Aroport Mohamed V, Agadir, Aguelmous, Anza, Benslimane, Bni Hafida, Cabo Negro, Casablanca,Fs, Lakbab, Marrakech, Merchich, Mohammdia, Rabat, Sal, Tanger, Tan Tan, Taounate, Tit Mellil, Zag. Japan 5 GHz Korea Taiwan

MODIFICATIONS TO THE PRODUCT CE Marking Gateway cannot be held responsible for unauthorized modifications made by the user and the consequences thereof, which may alter the conformity of the product with the CE Marking. Regulatory information - 99 Radio frequency interference The manufacturer is not responsible for any radio or TV interference caused by unauthorised modifications to this equipment. CONNECTIONS AND REMOTE EARTHS PELV (Protected Extra Low Voltage) To ensure the extra-low voltage integrity of the equipment, only connect equipment with mains-protected electrically-compatible circuits to the external ports. SELV (Safety Extra Low Voltage) Every input and output of this product is classified as Safety Extra Low Voltage. Remote earths To prevent electrical shock, connect all local (individual office) computers and computer support equipment to the same electrical circuit of the building wiring. If you are unsure, check the building wiring to avoid remote earth conditions. Building supply Only connect the equipment to a building supply that is in accordance with current wiring regulations in your country. In the U.K., these are the IEE regulations. POWER SUPPLY AND CABLES Power supply The power supply socket-inlet and socket-outlet (if equipped) are classified as Hazardous Voltage. You must unplug the power supply cord and remove the battery to disconnect the equipment from the power supply. In that aim, the socket-outlet should be installed near to the equipment and should be easily accessible. Input rating: Refer to the rating label on the bottom of the computer and ensure that your power adapter complies with the specified rating. 100 - Regulatory information Under no circumstances should the user attempt to disassemble the power supply. The power supply has no user-replaceable parts. Inside the power supply are hazardous voltages that can cause serious personal injury. A defective power supply must be returned to your dealer. Power cables and plug This Product requires a three-wire grounded power cord and plug. The plug only fits in a grounded power outlet. Make sure the power outlet is properly grounded before inserting the plug. Do not insert the plug into a non-grounded power outlet. Contact your electrician for details. The cord length must not exceed 2.5 metres. To prevent electrical hazards, do not remove or disable the ground contact on the power cord. Replace the power cord if it gets damaged. Contact your dealer for an exact replacement. In Europe, the plug must be rated for 250 VAC, 10 amp minimum. The plug must display an international agency approval marking. The cord must be suitable for use in the end-user country. Consult your dealer or the local electrical authorities if you are unsure of the type of power cord to use in your country. Cables For cables which are not delivered with the Product in the computer's packaging:

The EMC performance of the system is guaranteed only if the cable and interface use efficient shielding. The use of shielded interface cable is required for USB, IEEE1394, serial, printer, game, analog or digital audio/ video, PS2, TV or FM antennas, and generally all high-speed cable interfaces. Use only UL Listed No. 26AWG or larger telecommunication cords. Only Ethernet LAN or RTC modem cable can have length exceeding 3 metres. Gateway recommends that you add a ferrite core round clip to each cable connecting your computer to a hardware device that was not included with your computer.

- Ferrite reference: 28A-2029 from Steward (two loops) Regulatory information - 101 During product certification, Gateway used the following cable quality:

- USB2.0 Certified Cables from Hama 46778

- RCA-RCA shielded Audio/Video Cables from Thomson KHC001M, KHC012M, IEEE1394 shielded FireWire from Hama 50011 KHC028M

- Stereo Jack shielded Audio cables from Hama 43330H, 42714H Heat Build-up and Portable Computers The AC adapter and the underside of the computer can become hot after prolonged use. Sustained physical contact with either should be avoided. CHASSIS COVER REMOVAL AND REPLACEMENT Before removing the chassis cover to service or modify the equipment, you must disconnect all power and modem cords, and remove or disable the battery. Caution: Some components inside the computer can become hot after prolonged use. You then must close the chassis before you plug in and switch on the equipment. LASER COMPLIANCE STATEMENT The optical devices are tested and certified to be compliant with International Electrotechnical Commission IEC60825-1 and European EN60825-1 standards for Class 1 laser products. Class 1 laser products are not considered hazardous. The optical devices are designed such that there is never human access to laser radiation above a Class 1 level during normal operation or prescribed maintenance conditions. The optical devices installed in your computer are designed for use solely as components of such electronic product and therefore do not comply with the appropriate requirements of Code of Federal Regulation Sec. 1040.10 and Sec. 1040.11 for COMPLETE laser products. Because exposure to laser radiation is extremely hazardous, under no circumstances should the user attempt to disassemble the laser device. 102 - Regulatory information PACKAGING The packaging of this product is compliant with the European Environmental Directive 94/

62/EC from December 20 th 1994 and its equivalent in the French Legislation by the Decree 98-638 from july 20 th 1998. COMPLIANT WITH RUSSIAN REGULATORY CERTIFICATION Regulatory information - 103

OEM Installation Guidance Document For BRCM WLAN and Blutetooth Module, BCM943228HMB FCC ID: QDS-BRCM1058; IC: 4324A-BRCM1058 Conditions on using BRCM regulatory approvals:

Customer must ensure that its product (the CUSTOMER Product) is electrically A. identical to Broadcoms reference designs. Customer acknowledges that any modifications to Broadcoms reference designs may invalidate regulatory approvals in relation to the CUSTOMER Product, or may necessitate notifications to the relevant regulatory authorities. Customer is responsible for ensuring that antennas used with the product are of B. the same type, with same or lower gains as approved and providing antenna reports to Broadcom. Customer is responsible for regression testing to accommodate changes to C. Broadcoms reference designs, new antennas, and portable RF exposure safety testing/approvals. Appropriate labels must be affixed to the CUSTOMER Product that comply with D. applicable regulations in all respects. E. product that contains the text as required by applicable law. Without limitation of the foregoing, an example (for illustration purposes only) of possible text to include is set forth below:

A users manual or instruction manual must be included with the customer 1. USAFederal Communications Commission (FCC) FCC COMPLIANCE STATEMENT:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INFORMATION TO USER:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the Page 1 of 8 OEM Installation Guidance Document For BRCM WLAN and Blutetooth Module, BCM943228HMB FCC ID: QDS-BRCM1058; IC: 4324A-BRCM1058 user is encouraged to try and correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna

-Increase the distance between the equipment and the receiver.

-Connect the equipment to outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. CAUTION: (this only applicable to 5GHz device) This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range. FCC requires this product to be used indoors for frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. System integrators must include the FCC ID on the end product. FCC Radio-Frequency Exposure & Approval Conditions:

1. Antennas must be installed in the display section of Netbook/notebook/laptop computer to provide at least 5.7mm separation distance from the transmitting antenna to the body of user during normal operating condition. 2. Transmitting antenna(s) can only be installed at the display section of computer. When this device is installed other than notebook computers, at least 20 cm separation distance shall be maintained between the transmitting antenna(s) to the body of user or nearby person. 3. The antenna(s) used for this transmitter must not be collocated or operating in conjunction with any other antenna or transmitter within a host device, except in accordance with FCC multi-transmitter product procedures. 4. Only those antennas with same type and lesser gain filed under this FCC ID number can be used with this device. 5. The regulatory label on the final system must include the statement: Contains FCC ID: QDS-BRCM1058 and/or IC: 4324A-BRCM1058 or using electronic labeling method as documented in KDB 784748. 6. The final system integrator must ensure there is no instruction provided in the user manual or customer documentation indicating how to install or remove the transmitter Page 2 of 8 OEM Installation Guidance Document For BRCM WLAN and Blutetooth Module, BCM943228HMB FCC ID: QDS-BRCM1058; IC: 4324A-BRCM1058 module except such device has implemented two-ways authentication between module and the host system. 7. The final host manual shall include the following regulatory statement:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna

-Increase the distance between the equipment and the receiver.

-Connect the equipment to outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2. Canada - Industry Canada (IC) Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. L utilisation de ce dispositif est autorise seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l utilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. This device has been designed to operate with a 802.11abgn antenna, having a maximum gain of 6.77dBi/2.4GHz and 5.65dBi/5GHz. Different types of antennas or the same type of antenna having a gain greater than 6.77dBi/2.4GHz and 5.65dBi/5GHz are strictly prohibited for use with this device. The required antenna impedance is 50ohms. Page 3 of 8 OEM Installation Guidance Document For BRCM WLAN and Blutetooth Module, BCM943228HMB FCC ID: QDS-BRCM1058; IC: 4324A-BRCM1058 Caution: (this only applicable to UNII device)

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and

(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. Caution: Exposure to Radio Frequency Radiation. To comply with RSS 102 RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. System integrators must include the IC ID on the end product. 3. Europe - EU Restrictions This equipment needs to be marked with the throughout the European community. 0984 symbol and can be used Marking by the symbol indicates that usage restrictions apply. Information to be supplied to the users:

802.11a Restrictions:

- This product is for indoor use only when using channels 36, 40, 44, 48, 52, 56, 60, or 64 (5150 5350 MHz).

- DFS and TPC must remain enabled to ensure product compliance with EC regulations.

- To ensure compliance with local regulations, be sure to select the country in which the access point is installed.

- This product can be used as shown in the table below:

Page 4 of 8 OEM Installation Guidance Document For BRCM WLAN and Blutetooth Module, BCM943228HMB FCC ID: QDS-BRCM1058; IC: 4324A-BRCM1058 5 GHz wireless LAN IEEE 802.11a Indoor Use Only A, AND, B, CH, D, CY, CZ, DK, ES, EST, F, FIN, FL, FR, GB, GR, H, I, IRL, IS, L, LT, M, MC, N, NL, P, PL, RSM, S, SK, SLO, V Caution: Exposure to Radio Frequency Radiation. To comply with RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. Czech:

User's Manual in Czech language and a statement of conformity with Directive 1999/5/EC in Czech language must be enclosed to each product. France:

2.4GHz for Metropolitan France:

In all Metropolitan dpartements, wireless LAN frequencies can be used under the following conditions, either for public or private use:

Indoor use: maximum power (EIRP*) of 100 mW for the entire 2400-2483.5 MHz frequency band Outdoor use: maximum power (EIRP*) of 100 mW for the 2400-2454 MHz band and with maximum power (EIRP*) of 10 mW for the 2454-2483 MHz band Note for system integrators:

- The module is tested to comply with the requirement of the R&TTE Directive. System integrators are responsible for compliance of the final device with the R&TTE Directive.

- Packaging: CE Marking must also be on the outer packaging of the product. The outer packaging must also provide an indication as to where the device is intended to be used and OR conversely, where there may be restrictions for use. 4. Taiwan - NCC Statement to be included in the user guide Statement- For general products Page 5 of 8 OEM Installation Guidance Document For BRCM WLAN and Blutetooth Module, BCM943228HMB FCC ID: QDS-BRCM1058; IC: 4324A-BRCM1058 Additional Statement - For 5G Band products 5.25G ~5.35G Translation:

Article 12 Without permission, any company, firm or user shall not alter the frequency, increase the power, or change the characteristics and functions of the original design of the certified lower power frequency electric machinery. Article 14 The application of low power frequency electric machineries shall not affect the navigation safety nor interfere a legal communication, if an interference is found, the service will be suspended until improvement is made and the interference no longer exists. The foregoing legal communication refers to the wireless telecommunication operated according to the telecommunications laws and regulations. The low power frequency electric machinery should be able to tolerate the interference of the electric wave radiation electric machineries and equipments for legal communications or industrial and scientific applications. Radio devices using 5.25-5.35GHz bands are restricted to indoor use only. Appendix:

(ID):

CCXXxxLPyyyZz

,, CCXXxxLPyyyZz . Page 6 of 8 OEM Installation Guidance Document For BRCM WLAN and Blutetooth Module, BCM943228HMB FCC ID: QDS-BRCM1058; IC: 4324A-BRCM1058 5. Korea Include the following statement either on the label or in the User Guide.

6. Argentina The current approval is in the name of Broadcoms local representative. It may be necessary to obtain regulatory approval in the name of the local distributor or importer. We suggest manufacturers check with their local distributors and importers in Argentina. 7. Brazil - Anatel Before using Broadcom Anatel approvals, 1. PC- OEM must make arrangement for its local offices or distributors to provide maintenance, technical assistance or replace any faulty products sold in Brazil. 2. All warranty services will be provided by the distributors or PC-OEM sales support in Brazil. An official agreement stating warranty responsibilities must be signed and made available to Broadcom. Interference statement to be included in the Users Guide

"Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio."

Translation:

"This equipment operates in secondary character. It can be affected by harmful interference. However, it cannot cause interference to systems operating in primary character."

8. South Africa ICASA PC-OEMs must make arrangement for importers to supply spare parts and carry out repairs in South Africa. 9. Indonesia - POSTEL Page 7 of 8 OEM Installation Guidance Document For BRCM WLAN and Blutetooth Module, BCM943228HMB FCC ID: QDS-BRCM1058; IC: 4324A-BRCM1058 PC-OEMs must make arrangement for importers to provide product warranty and after sales services. 10. Japan MIC Radio devices using 5.15-5.35GHz bands are restricted to indoor use only. Page 8 of 8

ThinkPad Edge / Lenovo(Beijing) Ltd. To: SIEMIC, INC. 2206 Ringwood Avenue, San Jose, CA 95131 USA Model Difference To whom it may concern, We are submitting an application for a class II permissive change to the FCC approval of the Company name: Broadcom Corporation, product description:

802.11a/b/g/n WLAN+BLUETOOTH PCI-E MINI CARD

(FCC: QDS-BRCM1058, IC: 4324A-BRCM1058). The transmitter module itself has not changed. Here are the changes:

Adding a portable platform, Lenovo model: ThinkPad $431, TPO0056A. The two names are for same one platform, the different names definition as following:

ThinkPad $431: Marketing name TPOO056A: Model name Any questions regarding this declaration, please dont hesitate to contact us. Sincerely yours, :

Sincerely, BT ba fi Nant/Tifle: Blank Company Name: ThinkPad Edge /Lenovo(Beijing) Ltd.