FCC ID: QDS-BRCM1090 Broadcom 802.11a/b/g/n/ac WLAN + Bluetooth PCI-E/SDIO NGFF 2230 Card

OEM Installation Guidance Document For Broadcom BCM94371ZAE FCC ID: QDS-BRCM1090; IC: 4324A-BRCM1090 Conditions on using BRCM regulatory approvals:

A users manual or instruction manual must be included with the customer OEM must inform Broadcom of any changes which may require the Class I or Appropriate labels must be affixed to the CUSTOMER Product that comply with Customer must ensure that its product (the CUSTOMER Product) is electrically A. identical to Broadcoms product. Customer acknowledges that any modifications to Broadcoms product may invalidate regulatory approvals in relation to the CUSTOMER Product, or may necessitate notifications to the relevant regulatory authorities. B. Class II permissive changes for the FCC. Any substituted antenna and RF cable assemblies must be approved by Broadcom in order to maintain compliance. C. applicable regulations in all respects. D. product that contains the text as required by applicable law. Without limitation of the foregoing, an example (for illustration purposes only) of possible text to include is set forth below:

1. USAFederal Communications Commission (FCC) FCC COMPLIANCE STATEMENT:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INFORMATION TO USER:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna

-Increase the distance between the equipment and the receiver.

-Connect the equipment to outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. Page 1 of 9 OEM Installation Guidance Document For Broadcom BCM94371ZAE FCC ID: QDS-BRCM1090; IC: 4324A-BRCM1090 Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. CAUTION: (this only applicable to 5GHz device) High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. System integrators must include the FCC ID on the end product. FCC Radio-Frequency Exposure & Approval Conditions:

1. Antennas must be installed in the display section or underneath the keyboard in Notebook/notebook/laptop computers to provide at least 5mm separation distance from the transmitting antenna to the body of user , or any other person during normal operating condition. Configuration in tablets must be with at least 10mm antenna-to-enclosure separation distance.

-For portable applications, the WLAN antennas used must be the same antennas as in this filing. The distance between two antennas (Chain 1 and Chain 2) is 5cm. 2. The antenna(s) used for this transmitter must not be collocated or operating in conjunction with any other antenna or transmitter within a host device, except in accordance with FCC multi-transmitter product procedures. 4. Only those antennas with same type and lesser gain filed under this FCC ID number can be used with this device. 5. The regulatory label on the final system must include the statement: Contains FCC ID: QDS-BRCM1090 or using electronic labeling method as documented in KDB 784748. 6. The final system integrator must ensure there is no instruction provided in the user manual or customer documentation indicating how to install or remove the transmitter module except such device has implemented two-ways authentication between module and the host system. 7. The final host manual shall include the following regulatory statement:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or Page 2 of 9 OEM Installation Guidance Document For Broadcom BCM94371ZAE FCC ID: QDS-BRCM1090; IC: 4324A-BRCM1090 television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna

-Increase the distance between the equipment and the receiver.

-Connect the equipment to outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2. Canada - Industry Canada (IC) This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Page 3 of 9 OEM Installation Guidance Document For Broadcom BCM94371ZAE FCC ID: QDS-BRCM1090; IC: 4324A-BRCM1090 Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter, IC ID: 4324A-BRCM1090, has been approved by Industry Canada to operate with the onboard antenna or a detachable WLAN antenna with a maximum gain of 3.9dB/2.4GHz and 5.8dBi/5GHz (PIFA). Any other detachable antennas, with a different type or having gains greater than approved are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Caution: (this only applicable to UNII device)

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and

(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. Caution: Exposure to Radio Frequency Radiation. To comply with RSS 102 RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. System integrators must include a label with Contains IC: 4324A-BRCM1090 on the end product. Industry Canada user statements should be provided in both English and French, at the time each product is offered for sale or lease in Canada. French:

Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s) l'opration est soumise aux deux conditions suivantes: . ( 1) ce dispositif ne doit pas causer d'interfrences et ( 2) cet appareil doit accepter toute interfrence , y compris les interfrences qui peuvent provoquer un mauvais fonctionnement de l'appareil. Conformment la rglementation d'Industrie Canada, cet metteur radio ne peut fonctionner l'aide d'une antenne d'un type et maximum ( ou moins ) Gain approuv pour l'metteur par Industrie Canada. Afin de rduire le risque d'interfrence avec d'autres utilisateurs, le type d'antenne et son gain doivent tre choisi que la puissance isotrope rayonne quivalente (PIRE ) ne dpasse pas ce qui est ncessaire pour une communication russie . Page 4 of 9 OEM Installation Guidance Document For Broadcom BCM94371ZAE FCC ID: QDS-BRCM1090; IC: 4324A-BRCM1090 Cet metteur radio, IC ID: 4324A-BRCM1090, a t approuv par Industrie Canada fonctionner avec l'antenne bord ou une antenne WLAN amovible avec un gain maximum de 3.9dB / 2,4 GHz et 5.8dBi / 5 GHz (PIFA) et. Tous les autres antennes amovibles, avec un type diffrent ou ayant des gains suprieurs approuve est strictement interdit d'utiliser avec cet appareil. L'impdance requise de l'antenne est de 50 ohms. Attention: (ceci ne s'applique un appareil UNII )

(I) l'appareil pour fonctionner dans la bande 5150-5250 MHz est rserv une utilisation en intrieur afin de rduire les risques d'interfrence nuisible aux systmes mobiles par satellite co- canal;

(ii) le gain d'antenne maximal autoris pour les dispositifs dans les bandes 5250-5350 MHz et 5470-5725 MHz doivent respecter la limite de pire , et

( iii) le gain d'antenne maximal autoris pour les dispositifs fonctionnant dans la bande 5725-5825 MHz doivent respecter les limites de pire spcifies pour le point --point et l'exploitation non point point , le cas chant . Les radars haute puissance sont dsigns comme utilisateurs principaux de 5,25 5,35 GHz et 5,65 5,85 GHz . Ces stations radars peuvent causer des interfrences et / ou endommager cet appareil . Attention: Exposition aux radiations de frquences radio. Pour se conformer aux normes RSS 102 exigences de conformit d'exposition aux radiofrquences , pour les configurations mobiles , une distance de sparation d'au moins 20 cm doit tre maintenue entre l' antenne de cet appareil et toutes les personnes . Cet appareil ne doit pas tre co- localises ou oprant en conjonction avec une autre antenne ou transmetteur . Les intgrateurs de systmes doivent comporter une tiquette avec Contient IC: 4324A BRCM1090" . Sur le produit final comptes d'utilisateur d'Industrie Canada devraient tre fournis en anglais et en franais , au moment o chaque produit est offert la vente ou la location au Canada. For portable configurations, antennas must be installed in the display section or underneath the keyboard in Notebook/notebook/laptop/tablet computers to provide at least 5mm separation distance from the transmitting antenna to the body of user, or any other person during normal operating condition. Pour les configurations portables , antennes doivent tre installes dans la section d'affichage ou sous le clavier dans Netbook / portables / ordinateurs portable / tablette pour assurer une distance de sparation d'au moins 5 mm de l'antenne d'mission sur le corps de l'utilisateur , ou toute autre personne au cours de fonctionnement normal . 3. Europe - EU Restrictions This equipment needs to be marked with the throughout the European community. 0560 symbol and can be used Page 5 of 9 OEM Installation Guidance Document For Broadcom BCM94371ZAE FCC ID: QDS-BRCM1090; IC: 4324A-BRCM1090 Marking by the symbol indicates that usage restrictions apply. Information to be supplied to the users:

802.11a Restrictions:

- This product is for indoor use only when using channels 36, 40, 44, 48, 52, 56, 60, or 64 (5150 5350 MHz).

- DFS and TPC must remain enabled to ensure product compliance with EC regulations.

- To ensure compliance with local regulations, be sure to select the country in which the access point is installed.

- This product can be used as shown in the table below:

5 GHz wireless LAN IEEE 802.11a Indoor Use Only A, AND, B, CH, D, CY, CZ, DK, ES, EST, F, FIN, FL, FR, GB, GR, H, I, IRL, IS, L, LT, M, MC, N, NL, P, PL, RSM, S, SK, SLO, V Caution: Exposure to Radio Frequency Radiation. To comply with RF exposure compliance requirements, for mobile configurations, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. Czech:

User's Manual in Czech language and a statement of conformity with Directive 1999/5/EC in Czech language must be enclosed to each product. Italy:

For private use, a general authorisation is required if WAS/RLANs are used outside own premises. For public use, a general authorisation is required Note for system integrators:

- The module is tested to comply with the requirement of the R&TTE Directive. System integrators are responsible for compliance of the final device with the R&TTE Directive.

- Packaging: CE Marking must also be on the outer packaging of the product. The outer packaging must also provide an indication as to where the device is intended to be used and OR conversely, where there may be restrictions for use. Page 6 of 9 OEM Installation Guidance Document For Broadcom BCM94371ZAE FCC ID: QDS-BRCM1090; IC: 4324A-BRCM1090 4. Taiwan - NCC Statement to be included in the user guide Statement- For general products Additional Statement - For 5G Band products 5.25G ~5.35G Translation:

Article 12 Without permission, any company, firm or user shall not alter the frequency, increase the power, or change the characteristics and functions of the original design of the certified lower power frequency electric machinery. Article 14 The application of low power frequency electric machineries shall not affect the navigation safety nor interfere a legal communication, if an interference is found, the service will be suspended until improvement is made and the interference no longer exists. The foregoing legal communication refers to the wireless telecommunication operated according to the telecommunications laws and regulations. The low power frequency electric machinery should be able to tolerate the interference of the electric wave radiation electric machineries and equipments for legal communications or industrial and scientific applications. Radio devices using 5.25-5.35GHz bands are restricted to indoor use only. Appendix:

(ID):

CCXXxxLPyyyZz

,, Page 7 of 9 OEM Installation Guidance Document For Broadcom BCM94371ZAE FCC ID: QDS-BRCM1090; IC: 4324A-BRCM1090 CCXXxxLPyyyZz . 5. Korea Include the following statement either on the label or in the User Guide.

"

"

6. Argentina The current approval is in the name of Broadcoms local representative. It may be necessary to obtain regulatory approval in the name of the local distributor or importer. We suggest manufacturers check with their local distributors and importers in Argentina. 7. Brazil - Anatel Before using Broadcom Anatel approvals, 1. PC- OEM must make arrangement for its local offices or distributors to provide maintenance, technical assistance or replace any faulty products sold in Brazil. 2. All warranty services will be provided by the distributors or PC-OEM sales support in Brazil. An official agreement stating warranty responsibilities must be signed and made available to Broadcom. Interference statement to be included in the Users Guide

"Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio."

Translation:

"This equipment operates in secondary character. It can be affected by harmful interference. However, it cannot cause interference to systems operating in primary character."

8. South Africa ICASA PC-OEMs must make arrangement for importers to supply spare parts and carry out repairs in South Africa. 9. Indonesia POSTEL, Kenya CCK, Nepal - NTA Page 8 of 9 OEM Installation Guidance Document For Broadcom BCM94371ZAE FCC ID: QDS-BRCM1090; IC: 4324A-BRCM1090 PC-OEMs must make arrangement for importers to provide product warranty and after sales services. 10. Japan MIC Radio devices using 5.15-5.35GHz bands are restricted to indoor use only. 11. Mexico PC-OEMs must make arrangement for importers to provide User Manual in Spanish in Mexico. The User Manual must feature the following mandatory statement:

La operacin de este equipo est sujeta a las siguientes dos condiciones:

(1) es posible que este equipo o dispositivo no cause interferencia prejudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. Translation:

The operation of this device is subject to the following two conditions:

(1) this equipment or device must not cause harmful interference and

(2) this equipment or device must accept any interference, including interference which could otherwise cause its undesired operation. 12. CB Certifications PC-OEMs must provide User Guides in the language suitable for the countries when shipping products to countries listed in the CB reports. 13. Moldova- Labeling to be included Proper Marking must be included on each certified unit shipping into Moldova. 14. Tunisia When shipping into Tunisia, only 5150-5350MHz is allowed for the 5GHz WLAN. Passive Scan on other 5GHz channels is prohibited. Page 9 of 9

User Guide Product notice Software terms This guide describes features that are common to most products. Some features may not be available on your computer. Not all features are available in all editions or versions of Windows. Systems may require upgraded and/or separately purchased hardware, drivers, software or BIOS update to take full advantage of Windows functionality. See http://www.microsoft.com. To access the latest user guides or manuals for your product, go to http://www.hp.com/

support, and select your country. Select Find your product, and then follow the on-screen instructions. By installing, copying, downloading, or otherwise using any software product preinstalled on this computer, you agree to be bound by the terms of the HP End User License Agreement (EULA). If you do not accept these license terms, your sole remedy is to return the entire unused product (hardware and software) within 14 days for a full refund subject to the refund policy of your seller. For any further information or to request a full refund of the price of the computer, please contact your seller. Copyright 2016 HP Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by HP Inc. under license. Intel, Celeron, and Pentium are trademarks of Intel Corporation in the U.S. and other countries. Windows is a registered trademark of Microsoft Corporation in the United States and/or other countries. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. First Edition: April 2016 Document Part Number: 843577-001 Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to come into contact with the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the AC adapter comply with the user-accessible surface temperature limits defined by the International Standard for Safety of Information Technology Equipment (IEC 60950-1). iii iv Safety warning notice Processor configuration setting (select products only) IMPORTANT: Select products are configured with an Intel Pentium N35xx/N37xx series or a Celeron N28xx/N29xx/N30xx/N31xx series processor and a Windows operating system. If your computer is configured as described, do not change the processor configuration setting in msconfig.exe from 4 or 2 processors to 1 processor. If you do so, your computer will not restart. You will have to perform a factory reset to restore the original settings. v vi Processor configuration setting (select products only) Table of contents 1 Starting right ................................................................................................................................................ 1 Visit the HP Apps Store .......................................................................................................................................... 1 Best practices ......................................................................................................................................................... 1 More HP resources ................................................................................................................................................. 2 2 Getting to know your computer ...................................................................................................................... 4 Locating hardware ................................................................................................................................................. 4 Locating software .................................................................................................................................................. 4 Right side ............................................................................................................................................................... 5 Left side ................................................................................................................................................................. 7 Display ................................................................................................................................................................. 11 Changing your notebook position (select products only) ................................................................. 13 Changing your notebook to an entertainment stand (select products only) ................................... 14 Changing your notebook to an interactive stand (select products only) ......................................... 15 Changing your notebook to a tablet (select products only) ............................................................. 15 Top ........................................................................................................................................................................ 16 TouchPad ........................................................................................................................................... 16 Lights ................................................................................................................................................. 17 Speakers ............................................................................................................................................ 18 Keys ................................................................................................................................................... 19 Using the action keys ........................................................................................................................ 20 Bottom ................................................................................................................................................................. 21 Labels ................................................................................................................................................................... 22 3 Connecting to a network .............................................................................................................................. 23 Connecting to a wireless network ....................................................................................................................... 23 Using the wireless controls ............................................................................................................... 23 Airplane mode key .......................................................................................................... 23 Operating system controls ............................................................................................. 23 Connecting to a WLAN ....................................................................................................................... 24 Using HP Mobile Broadband (select products only) .......................................................................... 24 Using GPS (select products only) ...................................................................................................... 25 Using Bluetooth wireless devices (select products only) ................................................................. 25 Connecting Bluetooth devices ........................................................................................ 25 Connecting to a wired networkLAN (select products only) ............................................................................. 26 Sharing data and drives and accessing software ................................................................................................ 26 vii 4 Enjoying entertainment features .................................................................................................................. 27 Using a webcam (select products only) ............................................................................................................... 27 Using audio .......................................................................................................................................................... 27 Connecting speakers ......................................................................................................................... 27 Connecting headsets ......................................................................................................................... 27 Using sound settings ......................................................................................................................... 28 Using video .......................................................................................................................................................... 28 Connecting devices using a USB Type-C cable (select products only) .............................................. 29 Connecting video devices using an HDMI cable ................................................................................ 30 Setting up HDMI audio .................................................................................................... 30 Discovering and connecting to Miracast-compatible wireless displays (select products only) ...... 31 Discovering and connecting to Intel WiDi certified displays (select Intel products only) ................ 31 5 Navigating the screen .................................................................................................................................. 32 Using TouchPad and touch screen gestures ........................................................................................................ 32 Tap ..................................................................................................................................................... 32 Two-finger pinch zoom ..................................................................................................................... 33 Two-finger scroll (TouchPad only) .................................................................................................... 33 Two-finger tap (TouchPad only) ........................................................................................................ 33 Four-finger tap (TouchPad only) ....................................................................................................... 34 Three-finger swipe (TouchPad only) ................................................................................................. 34 One-finger slide (touch screen only) ................................................................................................. 34 Using the keyboard and optional mouse ............................................................................................................. 35 Using the on-screen keyboard .......................................................................................................... 35 Using the integrated numeric keypad (select products only) ............................................................................. 35 6 Managing power .......................................................................................................................................... 36 Initiating and exiting Sleep and Hibernation ....................................................................................................... 36 Manually initiating and exiting Sleep ................................................................................................ 37 Manually initiating and exiting Hibernation (select products only) ................................................. 37 Setting password protection on wakeup (exiting Sleep or Hibernation) ......................................... 37 Using the power meter and power settings ........................................................................................................ 38 Running on battery power ................................................................................................................................... 38 Factory-sealed battery ...................................................................................................................... 38 Finding battery information .............................................................................................................. 39 Conserving battery power ................................................................................................................. 39 Identifying low battery levels ........................................................................................................... 39 Resolving a low battery level ............................................................................................................ 40 Resolving a low battery level when external power is available ................................... 40 Resolving a low battery level when no power source is available ................................. 40 viii Resolving a low battery level when the computer cannot exit Hibernation .................. 40 Running on AC power ........................................................................................................................................... 40 Troubleshooting power problems ..................................................................................................... 41 Shutting down (turning off) the computer .......................................................................................................... 41 7 Maintaining your computer .......................................................................................................................... 43 Improving performance ....................................................................................................................................... 43 Using Disk Defragmenter .................................................................................................................. 43 Using Disk Cleanup ............................................................................................................................ 43 Using HP 3D DriveGuard (select products only) ................................................................................ 43 Identifying HP 3D DriveGuard status .............................................................................. 44 Updating programs and drivers .......................................................................................................................... 44 Cleaning your computer ...................................................................................................................................... 44 Cleaning procedures .......................................................................................................................... 44 Cleaning the display ........................................................................................................ 45 Cleaning the sides or cover ............................................................................................. 45 Cleaning the TouchPad, keyboard, or mouse (select products only) ............................. 45 Traveling with or shipping your computer .......................................................................................................... 45 8 Securing your computer and information ....................................................................................................... 47 Using passwords .................................................................................................................................................. 47 Setting Windows passwords ............................................................................................................. 47 Setting Setup Utility (BIOS) passwords ............................................................................................. 48 Using Windows Hello (select products only) ....................................................................................................... 48 Using Internet security software ......................................................................................................................... 48 Using antivirus software ................................................................................................................... 49 Using firewall software ..................................................................................................................... 49 Installing software updates ................................................................................................................................. 49 Using HP Touchpoint Manager (select products only) ........................................................................................ 50 Securing your wireless network .......................................................................................................................... 50 Backing up your software applications and information .................................................................................... 50 Using an optional security cable (select products only) ..................................................................................... 50 9 Using Setup Utility (BIOS) ............................................................................................................................. 51 Starting Setup Utility (BIOS) ................................................................................................................................ 51 Updating Setup Utility (BIOS) .............................................................................................................................. 51 Determining the BIOS version ........................................................................................................... 51 Downloading a BIOS update .............................................................................................................. 52 ix 10 Using HP PC Hardware Diagnostics (UEFI) ..................................................................................................... 53 Downloading HP PC Hardware Diagnostics (UEFI) to a USB device .................................................................... 53 11 Backing up, restoring, and recovering .......................................................................................................... 55 Creating recovery media and backups ................................................................................................................ 55 Creating HP Recovery media (select products only) ......................................................................... 55 Using Windows tools ........................................................................................................................................... 56 Restore and recovery ........................................................................................................................................... 57 Recovering using HP Recovery Manager ........................................................................................... 57 What you need to know before you get started ............................................................. 57 Using the HP Recovery partition (select products only) ................................................. 58 Using HP Recovery media to recover .............................................................................. 58 Changing the computer boot order ................................................................................ 59 Removing the HP Recovery partition (select products only) ......................................... 60 12 Specifications ............................................................................................................................................ 61 Input power .......................................................................................................................................................... 61 Operating environment ....................................................................................................................................... 61 13 Electrostatic Discharge .............................................................................................................................. 63 14 Accessibility .............................................................................................................................................. 64 Supported assistive technologies ....................................................................................................................... 64 Contacting support .............................................................................................................................................. 64 Index ............................................................................................................................................................. 65 x 1 Starting right This computer is a powerful tool designed to enhance your work and entertainment. Read this chapter to learn about best practices after you set up your computer, fun things to do with your computer, and where to find additional HP resources. Visit the HP Apps Store The HP Apps Store offers a wide choice of popular games, entertainment and music apps, productivity apps, and apps exclusive to HP that you can download to the desktop. The selection is updated regularly and includes regional content and country-specific offers. Be sure to check the HP Apps Store frequently for new and updated features. IMPORTANT: You must be connected to the Internet to access the HP Apps Store. To view and download an app:

1. Select the Start button, and then select the Store app. or Select the Store icon next to the taskbar search box. Select the app you want to download, and then follow the on-screen instructions. When the download is complete, the app appears on the All apps screen. 2. Best practices After you set up and register the computer, we recommend the following steps to get the most out of your smart investment:

Back up your hard drive by creating recovery media. See Backing up, restoring, and recovering on page 55. If you havent already done so, connect to a wired or wireless network. See details in Connecting to a network on page 23. Become familiar with the computer hardware and software. For more information, see Getting to know your computer on page 4 and Enjoying entertainment features on page 27. Update or purchase antivirus software. See Using antivirus software on page 49. Visit the HP Apps Store 1 More HP resources To locate resources that provide product details, how-to information, and more, use this table. Contents Overview of computer setup and features Online chat with an HP technician Support telephone numbers HP service center locations Proper workstation setup Guidelines for posture and work habits that increase your comfort and decrease your risk of injury Electrical and mechanical safety information Important regulatory notices, including information about proper battery disposal, if needed. Resource Setup Instructions HP support For HP support, go to http://www.hp.com/support. Safety & Comfort Guide To access this guide:

Select the Start button, select All apps, select HP Help and Support, and then select HP Documentation. or Select the Start button, select All apps, select HP, and then select HP Documentation. or Type support in the taskbar search box, and then select the HP Support Assistant app. Select My PC, select the Specifications tab, and then select User Guides. or Click the question mark icon in the taskbar. Select My PC, select the Specifications tab, and then select User Guides. or Go to http://www.hp.com/ergo. IMPORTANT: You must be connected to the Internet to access the latest version of the user guide. Regulatory, Safety and Environmental Notices To access this document:

Select the Start button, select All apps, select HP Help and Support, and then select HP Documentation. or Select the Start button, select All apps, select HP, and then select HP Documentation. or Type support in the taskbar search box, and then select the HP Support Assistant app. Select My PC, select the Specifications tab, and then select User Guides. or 2 Chapter 1 Starting right Resource Contents Click the question mark icon in the taskbar. Select My PC, select the Specifications tab, and then select User Guides. Limited Warranty*

Specific warranty information about this computer To access this document:

Select the Start button, select All apps, select HP Help and Support, and then select HP Documentation. or Select the Start button, select All apps, select HP, and then select HP Documentation. or Type support in the taskbar search box, and then select the HP Support Assistant app. Select My PC, select the Specifications tab, and then select User Guides. or Click the question mark icon in the taskbar. Select My PC, select the Specifications tab, and then select User Guides. or Go to http://www.hp.com/go/orderdocuments. IMPORTANT: You must be connected to the Internet to access the latest version of the user guide.

*You can find your HP Limited Warranty located with the user guides on your product and/or on the CD or DVD provided in the box. In some countries or regions, HP may provide a printed warranty in the box. For countries or regions where the warranty is not provided in printed format, you can request a copy from http://www.hp.com/go/orderdocuments. For products purchased in Asia Pacific, you can write to HP at POD, PO Box 161, Kitchener Road Post Office, Singapore 912006. Include your product name, and your name, phone number, and postal address. More HP resources 3 2 Getting to know your computer Locating hardware To find out what hardware is installed on your computer:

Type device manager in the taskbar search box, and then select the Device Manager app. A list displays all the devices installed on your computer. For information about system hardware components and the system BIOS version number, press fn+esc

(select products only). Locating software To find out what software is installed on your computer:

Select the Start button, and then select All apps. or Right-click the Start button, and then select Programs and Features. 4 Chapter 2 Getting to know your computer Right side NOTE: Refer to the illustration that most closely matches your computer. Component Description

(1) Memory card reader Reads optional memory cards that enable you to store, manage, share, or access information. To insert a card:

1. 2. Hold the card label-side up, with connectors facing the computer. Insert the card into the memory card reader, and then press in on the card until it is firmly seated. To remove a card:

Press in on the card, and then remove it from the memory card reader. USB Type-C port Connects an optional USB device with a Type-C connector.

(2)

(3) USB 3.0 charging (powered) port

(4) HDMI port

(5) AC adapter and battery light Connects an optional USB device, such as a keyboard, mouse, external drive, printer, scanner, or USB hub. Standard USB ports will not charge all USB devices or will charge using a low current. Some USB devices require power and require you to use a powered port. NOTE: USB charging ports can also charge select models of cell phones and MP3 players, even when the computer is off. Connects an optional video or audio device, such as a high-

definition television, any compatible digital or audio component, or a high-speed High-Definition Multimedia Interface (HDMI) device. White: The AC adapter is connected and the battery is fully charged. Blinking white: The AC adapter is disconnected and the battery has reached a low battery level. Amber: The AC adapter is connected and the battery is charging. Off: The battery is not charging.

(6) Power connector Connects an AC adapter. Right side 5 Component Description

(1) Memory card reader

(2)

(3) USB 3.0 ports (2) HDMI port

(4) AC adapter and battery light Reads optional memory cards that enable you to store, manage, share, or access information. To insert a card:

1. 2. Hold the card label-side up, with connectors facing the computer. Insert the card into the memory card reader, and then press in on the card until it is firmly seated. To remove a card:

Press in on the card, and then remove it from the memory card reader. Connect optional USB devices, such as a keyboard, mouse, external drive, printer, scanner or USB hub. Connects an optional video or audio device, such as a high-

definition television, any compatible digital or audio component, or a high-speed High-Definition Multimedia Interface (HDMI) device. White: The AC adapter is connected and the battery is fully charged. Blinking white: The AC adapter is disconnected and the battery has reached a low battery level. Amber: The AC adapter is connected and the battery is charging. Off: The battery is not charging.

(5) Power connector Connects an AC adapter. 6 Chapter 2 Getting to know your computer Left side NOTE: Refer to the illustration that most closely matches your computer. Component

(1) Power button

(2) Power light Description When the computer is off, press the button to turn on the computer. When the computer is on, press the button briefly to initiate Sleep. When the computer is in the Sleep state, press the button briefly to exit Sleep. When the computer is in Hibernation, press the button briefly to exit Hibernation. CAUTION: Pressing and holding down the power button results in the loss of unsaved information. If the computer has stopped responding and shutdown procedures are ineffective, press and hold the power button down for at least 5 seconds to turn off the computer. To learn more about your power settings, see your power options. Type power in the taskbar search box, and then select Power and sleep settings. or Right-click the Start button, and then select Power Options. On: The computer is on. Blinking: The computer is in the Sleep state, a power-

saving state. The computer shuts off power to the display and other unneeded components. Off: The computer is off or in Hibernation. Hibernation is a power-saving state that uses the least amount of power.

(3)

(4) Security cable slot Attaches an optional security cable to the computer. USB 3.0 port NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. Connects an optional USB device, such as a keyboard, mouse, external drive, printer, scanner or USB hub. Left side 7 Component

(5) Audio-out (headphone)/Audio-in (microphone) combo jack Description Connects optional powered stereo speakers, headphones, earbuds, a headset, or a television audio cable. Also connects an optional headset microphone. This jack does not support optional standalone microphones. WARNING! To reduce the risk of personal injury, adjust the volume before putting on headphones, earbuds, or a headset. For additional safety information, refer to the Regulatory, Safety, and Environmental Notices. To access this guide:

Select the Start button, select All apps, select HP Help and Support, and then select HP Documentation. NOTE: When a device is connected to the jack, the computer speakers are disabled.

(6) Volume button Control speaker volume on the computer.

(7) Drive light 1. 2. To increase speaker volume, press the back edge of the button. To decrease speaker volume, press the front edge of the button. Blinking white: The hard drive is being accessed. Amber: HP 3D DriveGuard has temporarily parked the hard drive. For information about HP 3D DriveGuard, see NOTE:

Using HP 3D DriveGuard (select products only) on page 43. NOTE: On select products, the drive light will always remain off. Component

(1) Power button Description When the computer is off, press the button to turn on the computer. When the computer is on, press the button briefly to initiate Sleep. When the computer is in the Sleep state, press the button briefly to exit Sleep. When the computer is in Hibernation, press the button briefly to exit Hibernation. 8 Chapter 2 Getting to know your computer Component Description CAUTION: Pressing and holding down the power button results in the loss of unsaved information. If the computer has stopped responding and shutdown procedures are ineffective, press and hold the power button down for at least 5 seconds to turn off the computer. To learn more about your power settings, see your power options. Type power in the taskbar search box, and then select Power and sleep settings. or Right-click the Start button, and then select Power Options. On: The computer is on. Blinking: The computer is in the Sleep state, a power-

saving state. The computer shuts off power to the display and other unneeded components. Off: The computer is off or in Hibernation. Hibernation is a power-saving state that uses the least amount of power.

(2) Power light

(3)

(4)

(5) Security cable slot Attaches an optional security cable to the computer. USB 2.0 port Audio-out (headphone)/Audio-in (microphone) combo jack NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. Connects an optional USB device, such as a keyboard, mouse, external drive, printer, scanner, or USB hub. Connects optional powered stereo speakers, headphones, earbuds, a headset, or a television audio cable. Also connects an optional headset microphone. This jack does not support optional standalone microphones. WARNING! To reduce the risk of personal injury, adjust the volume before putting on headphones, earbuds, or a headset. For additional safety information, refer to the Regulatory, Safety, and Environmental Notices. To access this guide:

Select the Start button, select All apps, select HP Help and Support, and then select HP Documentation. NOTE: When a device is connected to the jack, the computer speakers are disabled.

(6) Volume button Control speaker volume on the computer.

(7) Drive light 1. 2. To increase speaker volume, press the back edge of the button. To decrease speaker volume, press the front edge of the button. Blinking white: The hard drive is being accessed. Amber: HP 3D DriveGuard has temporarily parked the hard drive. Left side 9 Component Description For information about HP 3D DriveGuard, see NOTE:

Using HP 3D DriveGuard (select products only) on page 43. NOTE: On select products, the drive light will always remain off. 10 Chapter 2 Getting to know your computer Display NOTE: Refer to the illustration that most closely matches your computer. Component Description

(1)

(2)

(3)

(4) WLAN antennas*

Internal microphones Webcam light Webcam Send and receive wireless signals to communicate with wireless local area networks (WLANs). Record sound. On: The webcam is in use. Records video and captures photographs. Some products allow you to video conference and chat online using streaming video. To use a webcam (integrated camera):

Type camera in the taskbar search box, and then select Camera.

*The antennas are not visible from the outside of the computer, and the antenna location may vary.For optimal transmission, keep the areas immediately around the antennas free from obstructions. For wireless regulatory notices, see the section of the Regulatory, Safety, and Environmental Notices that applies to your country or region. To access this guide:

Select the Start button, select All apps, select HP Help and Support, and then select HP Documentation. Display 11 Component Description

(1)

(2)

(3)

(4)

(5) WLAN antennas*

Send and receive wireless signals to communicate with wireless local area networks (WLANs). Infrared camera lights (2) (select products only) On: The infrared camera is in use. Internal microphones Webcam light Webcam Record sound. On: The webcam is in use. Records video and captures photographs. Some products allow you to video conference and chat online using streaming video. To use a webcam (integrated camera):

Type camera in the taskbar search box, and then select Camera.

(6) Infrared camera (select products only) Allows a facial recognition logon to Windows, instead of a password. For more information, see Using Windows Hello (select products only) on page 48.

*The antennas are not visible from the outside of the computer, and the antenna location may vary.For optimal transmission, keep the areas immediately around the antennas free from obstructions. For wireless regulatory notices, see the section of the Regulatory, Safety, and Environmental Notices that applies to your country or region. To access this guide:

Select the Start button, select All apps, select HP Help and Support, and then select HP Documentation. 12 Chapter 2 Getting to know your computer Changing your notebook position (select products only) Your computer can function as a classic notebook, and in addition, the display can be rotated so that the computer transforms into an entertainment stand, an interactive stand, or a tablet. NOTE: The TouchPad and keyboard functions are locked during the entertainment and tablet modes. Display 13 Changing your notebook to an entertainment stand (select products only) To change your notebook to an entertainment stand, raise the display, and then rotate the display backward to a stand position (about 315 degrees). 14 Chapter 2 Getting to know your computer Changing your notebook to an interactive stand (select products only) To change your notebook to an interactive stand, raise the display, and then rotate the display backward to a stand position (about 315 degrees). Position the notebook on its edges. Changing your notebook to a tablet (select products only) To change your notebook to a tablet, raise the display, and then rotate the display backward until it is flush with the computer bottom (360 degrees). NOTE: When the computer is in tablet mode, you can use the on-screen keyboard. See Using the on-screen keyboard on page 35. Display 15 Top TouchPad Component

(1)

(2)

(3) TouchPad zone Description Reads your finger gestures to move the pointer or activate items on the screen. For more information, see Using TouchPad and touch NOTE:

screen gestures on page 32. Left TouchPad button Right TouchPad button Functions like the left button on an external mouse. Functions like the right button on an external mouse. 16 Chapter 2 Getting to know your computer Lights NOTE: Your computer may look slightly different from the illustration below. Component Description

(1)

(2) Caps lock light Mute light On: Caps lock is on, which switches the key input to all capital letters. Amber: Computer sound is off. Off: Computer sound is on. Top 17 Speakers NOTE: Your computer may look slightly different from the illustration below. Component Speakers Description Produce sound. 18 Chapter 2 Getting to know your computer Keys NOTE: Your computer may look slightly different from the illustration below. Component Description

(1)

(2)

(3)

(4)

(5)

(6) esc key fn key Displays system information when pressed in combination with the fn key. Displays system information when pressed in combination with the esc key. Windows key Opens the Start menu. NOTE: Pressing the Windows key again will close the Start menu. Action keys Execute frequently used system functions. num lock key (select products only) NOTE: On select products, the f5 action key turns the keyboard backlight feature off or on. Alternates between the navigational and numeric functions on the integrated numeric keypad. Integrated numeric keypad (select products only) When num lock is on, the keypad can be used like an external numeric keypad. Top 19 Using the action keys An action key performs an assigned function. The icon on each action key illustrates the function for that key. To use an action key, press and hold the key. Icon Description Decreases the screen brightness incrementally as long as you hold down the key. Increases the screen brightness incrementally as long as you hold down the key. Switches the screen image between display devices connected to the system. For example, if a monitor is connected to the computer, repeatedly pressing this key alternates the screen image from the computer display to the monitor display to a simultaneous display on both the computer and the monitor. On select products, turns the keyboard backlight off or on. NOTE: To conserve battery power, turn off this feature. Plays the previous track of an audio CD or the previous section of a DVD or a Blu-ray Disc (BD). Starts, pauses, or resumes playback of an audio CD, a DVD, or a BD. Plays the next track of an audio CD or the next section of a DVD or a BD. Decreases speaker volume incrementally while you hold down the key. Increases speaker volume incrementally while you hold down the key. Mutes or restores speaker sound. Turns the airplane mode and wireless feature on or off. NOTE: The airplane mode key is also referred to as the wireless button. NOTE: A wireless network must be set up before a wireless connection is possible. 20 Chapter 2 Getting to know your computer Bottom NOTE: Refer to the illustration that most closely matches your computer. Component Vents (2) Description Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. Component Vents (3) Description Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. Bottom 21 Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer. IMPORTANT: Check the following locations for the labels described in this section: the bottom of the computer, inside the battery bay, under the service door, or on the back of the display. Service labelProvides important information to identify your computer. When contacting support, you will probably be asked for the serial number, and possibly for the product number or the model number. Locate these numbers before you contact support. Your service label will resemble one of the examples shown below. Refer to the illustration that most closely matches the service label on your computer. Component

(1)

(2)

(3)

(4) Serial number Product number Warranty period Model number (select products only) Component

(1)

(2)

(3)

(4) Model name (select products only) Product number Serial number Warranty period Regulatory label(s)Provide(s) regulatory information about the computer. Wireless certification label(s)Provide(s) information about optional wireless devices and the approval markings for the countries or regions in which the devices have been approved for use. 22 Chapter 2 Getting to know your computer 3 Connecting to a network Your computer can travel with you wherever you go. But even at home, you can explore the globe and access information from millions of websites using your computer and a wired or wireless network connection. This chapter will help you get connected to that world. Connecting to a wireless network Your computer may be equipped with one or more of the following wireless devices:

WLAN deviceConnects the computer to wireless local area networks (commonly referred to as Wi-Fi networks, wireless LANs, or WLANs) in corporate offices, your home, and public places such as airports, restaurants, coffee shops, hotels, and universities. In a WLAN, the mobile wireless device in your computer communicates with a wireless router or a wireless access point. HP Mobile Broadband ModuleGives you wireless connectivity over a wireless wide area network

(WWAN), a much larger area. Mobile network operators install base stations (similar to cell phone towers) throughout large geographic areas, effectively providing coverage across entire states, regions, or even countries. Bluetooth deviceCreates a personal area network (PAN) to connect to other Bluetooth-enabled devices such as computers, phones, printers, headsets, speakers, and cameras. In a PAN, each device communicates directly with other devices, and devices must be relatively close togethertypically within 10 meters (approximately 33 feet) of each other. For more information about wireless technology, the Internet, and networking, see the Get started app. Select the Start button, and then select the Get started app. Using the wireless controls You can control the wireless devices in your computer using one or more of these features:

Airplane mode key (also called wireless button or wireless key) (referred to in this chapter as airplane mode key) Operating system controls Airplane mode key The computer may have an airplane mode key, one or more wireless devices, and one or two wireless lights. All the wireless devices on your computer are enabled at the factory. The wireless light indicates the overall power state of your wireless devices, not the status of individual devices. Operating system controls The Network and Sharing Center allows you to set up a connection or network, connect to a network, and diagnose and repair network problems. Connecting to a wireless network 23 To use operating system controls:

1. Type control panel in the taskbar search box, and then select Control Panel. Select Network and Internet, and then select Network and Sharing Center. 2. For more information, see the information provided in the Get started app. Select the Start button, and then select the Get started app. Connecting to a WLAN NOTE: When you are setting up Internet access in your home, you must establish an account with an Internet service provider (ISP). To purchase Internet service and a modem, contact a local ISP. The ISP will help set up the modem, install a network cable to connect your wireless router to the modem, and test the Internet service. To connect to a WLAN, follow these steps:

1. Be sure that the WLAN device is on. 2. Select the network status icon in the taskbar, and then connect to one of the available networks. If the WLAN is a security-enabled WLAN, you are prompted to enter a security code. Enter the code, and then select Next to complete the connection. If no WLANs are listed, you may be out of range of a wireless router or access point. If you do not see the WLAN you want to connect to, right-click the network status icon in the NOTE:

NOTE:

taskbar, and then select Open Network and Sharing Center. Select Set up a new connection or network. A list of options is displayed, allowing you to manually search for and connect to a network or to create a new network connection. Follow the on-screen instructions to complete the connection. 3. After the connection is made, select the network status icon at the far right of the taskbar, to verify the name and status of the connection. NOTE: The functional range (how far your wireless signals travel) depends on WLAN implementation, router manufacturer, and interference from other electronic devices or structural barriers such as walls and floors. Using HP Mobile Broadband (select products only) Your HP Mobile Broadband computer has built-in support for mobile broadband service. Your new computer, when used with a mobile operators network, gives you the freedom to connect to the Internet, send e-mail, or connect to your corporate network without the need for Wi-Fi hotspots. You might need the HP Mobile Broadband Module IMEI and/or MEID number to activate mobile broadband service. The number may be printed on a label located on the bottom of your computer, inside the battery bay, under the service door, or on the back of the display. or You can find the number following these steps:

1. 2. 3. From the taskbar, select the network status icon. Select View Connection Settings. Under the Mobile broadband section, select the network status icon. 24 Chapter 3 Connecting to a network Some mobile network operators require the use of a subscriber identity module (SIM) card. A SIM card contains basic information about you, such as a personal identification number (PIN), as well as network information. Some computers include a SIM card that is preinstalled. If the SIM card is not preinstalled, it may be included with the HP Mobile Broadband documents provided with your computer, or the mobile network operator may provide it separately from the computer. For information about HP Mobile Broadband and how to activate service with a preferred mobile network operator, see the HP Mobile Broadband information included with your computer. Using GPS (select products only) Your computer may be equipped with a Global Positioning System (GPS) device. GPS satellites deliver location, speed, and direction information to GPS-equipped systems. To enable GPS, make sure location is enabled under the Windows privacy setting. 1. Type location in the taskbar search box, and then select Location privacy settings. Follow the on-screen instructions for using location settings. 2. For more information, see the Get started app. Select the Start button, and then select the Get started app. Using Bluetooth wireless devices (select products only) A Bluetooth device provides short-range wireless communications that replace the physical cable connections that traditionally link electronic devices such as the following:

Computers (desktop, notebook) Phones (cellular, cordless, smartphone) Imaging devices (printer, camera) Audio devices (headset, speakers) Mouse External keyboard Bluetooth devices provide peer-to-peer capability that allows you to set up a PAN of Bluetooth devices. For information about configuring and using Bluetooth devices, see the Get started app. Select the Start button, and then select the Get started app. Connecting Bluetooth devices Before you can use a Bluetooth device, you must establish a Bluetooth connection. 1. Type bluetooth in the taskbar search box, and then select Bluetooth settings. Turn on Bluetooth, if it is not already turned on. Select your device from the list, and then follow the on-screen instructions. 2. 3. NOTE:

If the device requires verification, a pairing code is displayed. On the device you are adding, follow the on-screen instructions to verify that the code on your device matches the pairing code. For more information, refer to the documentation provided with the device. NOTE:

devices may have additional requirements; refer to the documentation provided with the device. If your device does not appear in the list, be sure that Bluetooth on that device is turned on. Some Connecting to a wireless network 25 Connecting to a wired networkLAN (select products only) Use a LAN connection if you want to connect the computer directly to a router in your home (instead of working wirelessly), or if you want to connect to an existing network at your office. Connecting to a LAN requires an 8-pin, RJ-45 (network) cable and a network jack or an optional docking device or expansion port, if there is no RJ-45 jack on the computer. To connect the network cable, follow these steps:

1. 2. Plug the network cable into the network jack (1) on the computer. Plug the other end of the network cable into a network wall jack (2) or router. If the network cable contains noise suppression circuitry (3), which prevents interference from NOTE:

TV and radio reception, orient the circuitry end of the cable toward the computer. Sharing data and drives and accessing software When your computer is part of a network, you are not limited to using only the information that is stored in your computer. Computers connected to the network can exchange software and data with each other. For more information about sharing files, folders, or drives, see the information provided in the Get started app. Select the Start button, and then select the Get started app. NOTE: When a disc like a DVD movie or game is copy-protected, it cannot be shared. 26 Chapter 3 Connecting to a network 4 Enjoying entertainment features Use your HP computer as an entertainment hub to socialize via the webcam, enjoy and manage your music, and download and watch movies. Or, to make your computer an even more powerful entertainment center, connect external devices like a monitor, projector, TV, speakers, or headphones. Using a webcam (select products only) Your computer has a webcam (integrated camera) that records video and captures photographs. Some models allow you to video conference and chat online using streaming video. NOTE: Some products also have an infrared camera that allows you to log in to your computer using facial recognition software. For details, see Using Windows Hello (select products only) on page 48. To access the camera, type camera in the taskbar search box, and then select Camera from the list of applications. Using audio On your computer, or on select products using an external optical drive, you can play music CDs, download and listen to music, stream audio content from the web (including radio), record audio, or mix audio and video to create multimedia. To enhance your listening enjoyment, attach external audio devices such as speakers or headphones. Connecting speakers You can attach wired speakers to your computer by connecting them to a USB port or to the audio-out

(headphone)/audio-in (microphone) combo jack on your computer or on a docking station. To connect wireless speakers to your computer, follow the device manufacturer's instructions. To connect high-definition speakers to the computer, see Setting up HDMI audio on page 30. Before connecting speakers, lower the volume setting. Connecting headsets WARNING! To reduce the risk of personal injury, lower the volume setting before putting on headphones, earbuds, or a headset. For additional safety information, see the Regulatory, Safety and Environmental Notices. To access this document:

Select the Start button, select All apps, select HP Help and Support, and then select HP Documentation. Headphones combined with a microphone are called headsets. You can connect wired headsets to the audio-

out (headphone)/audio-in (microphone) combo jack on your computer. To connect wireless headsets to your computer, follow the device manufacturer's instructions. Using a webcam (select products only) 27 Using sound settings Use sound settings to adjust system volume, change system sounds, or manage audio devices. To view or change sound settings:

Type control panel in the taskbar search box, select Control Panel, select Hardware and Sound, and then select Sound. or Right-click the Start button, select Control Panel, select Hardware and Sound, and then select Sound. Your computer may include an enhanced sound system by Bang & Olufsen, DTS, Beats audio, or another provider. As a result, your computer may include advanced audio features that can be controlled through an audio control panel specific to your audio system. Use the audio control panel to view and control audio settings. Type control panel in the taskbar search box, select Control Panel, select Hardware and Sound, and then select the audio control panel specific to your system. or Right-click the Start button, select Control Panel, select Hardware and Sound, and then select the audio control panel specific to your system. Using video Your computer is a powerful video device that enables you to watch streaming video from your favorite websites and download video and movies to watch on your computer when you are not connected to a network. To enhance your viewing enjoyment, use one of the video ports on the computer to connect an external monitor, projector, or TV. IMPORTANT: Be sure that the external device is connected to the correct port on the computer, using the correct cable. Follow the device manufacturer's instructions. For information on using your video features, refer to HP Support Assistant. 28 Chapter 4 Enjoying entertainment features Connecting devices using a USB Type-C cable (select products only) NOTE: To connect a USB Type-C device to your computer, you need a USB Type-C cable, purchased separately. To see high-resolution display output on an external USB Type-C device, connect the USB Type-C device according to the following instructions:

1. Connect one end of the USB Type-C cable to the USB Type-C port on the computer. 2. 3. Connect the other end of the cable to the external device. Press fn+f4 to alternate the computer screen image between 4 display states. PC screen only: View the screen image on the computer only. Duplicate: View the screen image simultaneously on both the computer and external device. Extend: View the screen image extended across both the computer and external device. Second screen only: View the screen image on the external device only. Each time you press fn+f4 the display state changes. NOTE:

For best results, especially if you choose the "Extend" option, increase the screen resolution of the external device, as follows. Type control panel in the taskbar search box, select Control Panel, and then select Appearance and Personalization. Under Display, select Adjust resolution. Using video 29 Connecting video devices using an HDMI cable NOTE: To connect an HDMI device to your computer, you need an HDMI cable, purchased separately. To see the computer screen image on a high-definition TV or monitor, connect the high-definition device according to the following instructions:

1. Connect one end of the HDMI cable to the HDMI port on the computer. 2. 3. Connect the other end of the cable to the high-definition TV or monitor. Press f4 to alternate the computer screen image between 4 display states:

PC screen only: View the screen image on the computer only. Duplicate: View the screen image simultaneously on both the computer and the external device. Extend: View the screen image extended across both the computer and the external device. Second screen only: View the screen image on the external device only. Each time you press f4, the display state changes. NOTE:

For best results, especially if you choose the "Extend" option, increase the screen resolution of the external device, as follows. Type control panel in the taskbar search box, select Control Panel, and then select Appearance and Personalization. Under Display, select Adjust resolution. Setting up HDMI audio HDMI is the only video interface that supports high-definition video and audio. After you connect an HDMI TV to the computer, you can then turn on HDMI audio by following these steps:

1. Right-click the Speakers icon in the notification area, at the far right of the taskbar, and then select Playback devices. On the Playback tab, select the name of the digital output device. Click Set Default, and then click OK. 2. 3. 30 Chapter 4 Enjoying entertainment features To return the audio stream to the computer speakers:

1. Right-click the Speakers icon in the notification area, at the far right of the taskbar, and then click Playback devices. On the Playback tab, click Speakers. Click Set Default, and then click OK. 2. 3. Discovering and connecting to Miracast-compatible wireless displays (select products only) NOTE: To learn what type of display you have (Miracast-compatible or Intel WiDi), refer to the documentation that came with your TV or secondary display device. To discover and connect to Miracast-compatible wireless displays without leaving your current apps, follow the steps below. To open Miracast:

Type project in the taskbar search box, and then click Project to a second screen. Click Connect to a wireless display, and then follow the on-screen instructions. Discovering and connecting to Intel WiDi certified displays (select Intel products only) Use Intel WiDi to wirelessly project individual files such as photos, music, or videos, or to duplicate your entire computer screen to a TV or a secondary display device. Intel WiDi, a premium Miracast solution, makes it easy and seamless to pair your secondary display device;

provides for full-screen duplication; and improves speed, quality, and scaling. To connect to Intel WiDi certified displays:

Type project in the taskbar search box, and then click Project to a second screen. Click Connect to a wireless display, and then follow the on-screen instructions. To open Intel WiDi:

Type Intel WiDi in the taskbar search box, and then click Intel WiDi. Using video 31 5 Navigating the screen You can navigate the computer screen in the following ways:

Use touch gestures directly on the computer screen (select products only) Use touch gestures on the TouchPad Use keyboard and optional mouse (mouse purchased separately) Use an on-screen keyboard (select products only) Using TouchPad and touch screen gestures The TouchPad helps you navigate the computer screen and control the pointer using simple touch gestures. You can also use the left and right TouchPad buttons as you would use the corresponding buttons on an external mouse. To navigate a touch screen (select products only), touch the screen directly using gestures described in this chapter. You can also customize gestures and view demonstrations of how they work. Type control panel in the taskbar search box, select Control Panel, and then select Hardware and Sound. Under Devices and Printers, select Mouse. NOTE: Unless noted, gestures can be used on the TouchPad or a touch screen (select products only). Tap Use the tap/double-tap gesture to select or open an item on the screen. Point to an item on the screen, and then tap one finger on the TouchPad zone or touch screen to select the item. Double-tap an item to open it. 32 Chapter 5 Navigating the screen Two-finger pinch zoom Use the two-finger pinch zoom to zoom out or in on images or text. Zoom out by placing two fingers apart on the TouchPad zone or touch screen and then moving your fingers together. Zoom in by placing two fingers together on the TouchPad zone or touch screen and then moving your fingers apart. Two-finger scroll (TouchPad only) Use the two-finger scroll to move up, down, or sideways on a page or image. Place two fingers slightly apart on the TouchPad zone and then drag them up, down, left, or right. Two-finger tap (TouchPad only) Use the two-finger tap to open the menu for an object on the screen. NOTE: The two-finger tap performs the same function as right-clicking with the mouse. Tap two fingers on the TouchPad zone to open the options menu for the selected object. Using TouchPad and touch screen gestures 33 Four-finger tap (TouchPad only) Use the four-finger tap to open the action center. Tap four fingers on the Touchpad to open the action center and view current settings and notifications. Three-finger swipe (TouchPad only) Use the three-finger swipe to view open windows and to switch between open windows and the desktop. Swipe 3 fingers away from you to see all open windows. Swipe 3 fingers toward you to show the desktop. Swipe 3 fingers left or right to switch between open windows. One-finger slide (touch screen only) Use the one-finger slide to pan or scroll through lists and pages, or to move an object. To scroll across the screen, lightly slide one finger across the screen in the direction you want to move. To move an object, press and hold your finger on an object, and then drag your finger to move the object. 34 Chapter 5 Navigating the screen Using the keyboard and optional mouse The keyboard and optional mouse allow you to type, select items, scroll and to perform the same functions as you do using touch gestures. The keyboard also allows you to use action keys and key combinations to perform specific functions. NOTE: Depending on the country or region, your keyboard may have different keys and keyboard functions than those discussed in this section. Using the on-screen keyboard The computer has an on-screen keyboard that is displayed when you are in tablet mode. 1. To display the on-screen keyboard, tap the keyboard icon in the notification area, at the far right of the taskbar. Begin typing. To access settings for the on-screen keyboard, type control panel in the taskbar search box, select Control Panel, select Devices and Printers, and then select Typing. 2. NOTE: Suggested words may be displayed above the on-screen keyboard. Tap a word to select it. Using the integrated numeric keypad (select products only) On select products, the computer includes an integrated numeric keypad, and it also supports an optional external numeric keypad or an optional external keyboard that includes a numeric keypad. For more details about the integrated numeric keypad, see Keys on page 19. Component num lock key Integrated numeric keypad Description Controls the function of the integrated numeric keypad. Press the key to alternate between the standard numeric function found on an external keypad (this function is turned on at the factory) and the navigational function (indicated by the directional arrows on the keys). NOTE: The keypad function that is active when the computer is turned off, is reinstated when the computer is turned back on. Function like an external numeric keypad. To alternate between this numeric function and the navigational function (indicated by the directional arrow keys), press the num lock key. Using the keyboard and optional mouse 35 6 Managing power Your computer can operate on either battery power or external power. When the computer is running on battery power only and an AC power source is not available to charge the battery, it is important to monitor and conserve the battery charge. Initiating and exiting Sleep and Hibernation CAUTION: Several well-known vulnerabilities exist when a computer is in the Sleep state. To prevent an unauthorized user from accessing data on your computer, even encrypted data, HP recommends that you always initiate Hibernation instead of Sleep anytime the computer will be out of your physical possession. This practice is particularly important when you travel with your computer. Windows has two power-saving states, Sleep and Hibernation. SleepThe Sleep state is automatically initiated after a period of inactivity. Your work is saved to memory, allowing you to resume your work very quickly. You can also initiate Sleep manually. For more information, see Manually initiating and exiting Sleep on page 37. HibernationThe Hibernation state is automatically initiated if the battery reaches a critical level. In the Hibernation state, your work is saved to a hibernation file and the computer powers down. You can also initiate Hibernation manually. For more information, see Manually initiating and exiting Hibernation

(select products only) on page 37. CAUTION: To reduce the risk of possible audio and video degradation, loss of audio or video playback functionality, or loss of information, do not initiate the Sleep state while reading from or writing to a disc or an external media card. 36 Chapter 6 Managing power Manually initiating and exiting Sleep You can initiate Sleep in any of the following ways:

Close the display. Select the Start button, select the Power icon, and then select Sleep. You can exit Sleep in any of the following ways:

Briefly press the power button. If the computer is closed, raise the display. Press a key on the keyboard. Tap the TouchPad. When the computer exits Sleep, the power lights turn on and your work returns to the screen. NOTE:

before your work returns to the screen. If you have set a password to be required on exiting Sleep, you must enter your Windows password Manually initiating and exiting Hibernation (select products only) You can enable user-initiated Hibernation and change other power settings and timeouts using Power Options. 1. Type power options in the taskbar search box, and then select Power Options. or Right-click the Power meter icon

, and then select Power Options. 2. 3. In the left pane, select Choose what the power button does. Select Change Settings that are currently unavailable, and then, in the When I press the power button area, select Hibernate. or Under Shutdown settings, select the Hibernate box to show the Hibernate option in the Power menu. Select Save changes. 4. To exit Hibernation:

Briefly press the power button. When the computer exits Hibernation, the power lights turn on and your work returns to the screen. NOTE:

password before your work returns to the screen. If you have set a password to be required on exiting Hibernation, you must enter your Windows Setting password protection on wakeup (exiting Sleep or Hibernation) To set the computer to prompt for a password when the computer exits Sleep or Hibernation, follow these steps:

1. Type power options in the taskbar search box, and then select Power Options. or Initiating and exiting Sleep and Hibernation 37 Right-click the Power meter icon

, and then select Power Options. 2. 3. 4. In the left pane, select Require a password on wakeup. Select Change Settings that are currently unavailable. Select Require a password (recommended). NOTE: To create a user account password or change your current user account password, select Create or change your user account password, and then follow the on-screen instructions. If you do not need to create or change a user account password, go to step 5. 5. Select Save changes. Using the power meter and power settings The power meter is located on the Windows taskbar. The power meter allows you to quickly access power settings and view the remaining battery charge. To view the percentage of remaining battery charge and the current power plan, place the mouse pointer over the power meter icon

. To use Power Options, rightclick the power meter icon can also type power options in the task bar search box, and then select Power Options.

, and then select an item from the list. You Different power meter icons indicate whether the computer is running on battery or external power. Placing the mouse pointer over the icon reveals a message if the battery has reached a low or critical battery level. Running on battery power When a charged battery is in the computer and the computer is not plugged into external power, the computer runs on battery power. When the computer is off and unplugged from external power, the battery in the computer slowly discharges. The computer displays a message when the battery reaches a low or critical battery level. Computer battery life varies, depending on power management settings, programs running on the computer, screen brightness, external devices connected to the computer, and other factors. Factory-sealed battery To monitor the status of the battery, or if the battery is no longer holding a charge, run HP Battery Check in the HP Support Assistant app. 1. Type support in the taskbar search box, and then select the HP Support Assistant app. or Click the question mark icon in the taskbar. Select My PC, select the Diagnostics and tools tab, and then select HP Battery Check. If HP Battery Check indicates that your battery should be replaced, contact support. 2. The battery[ies] in this product cannot be easily replaced by users themselves. Removing or replacing the battery could affect your warranty coverage. If a battery is no longer holding a charge, contact support. When 38 Chapter 6 Managing power a battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for battery disposal. Finding battery information To access battery information:

1. Type support in the taskbar search box, and then select the HP Support Assistant app. or Click the question mark icon in the taskbar. Select My PC, select the Diagnostics and tools tab, and then select HP Battery Check. If HP Battery Check indicates that your battery should be replaced, contact support. 2. HP Support Assistant provides the following tools and information about the battery:

HP Battery Check Information about battery types, specifications, life cycles, and capacity Conserving battery power To conserve battery power and maximize battery life:

Lower the brightness of the display. Select the Power saver setting in Power Options. Turn off wireless devices when you are not using them. Disconnect unused external devices that are not plugged into an external power source, such as an external hard drive connected to a USB port. Stop, disable, or remove any external media cards that you are not using. Before you leave your work, initiate Sleep or shut down the computer. Identifying low battery levels When a battery that is the sole power source for the computer reaches a low or critical battery level, the following behavior occurs:

The battery light (select products only) indicates a low or critical battery level. or The power meter icon shows a low or critical battery notification. NOTE:

settings on page 38. For additional information about the power meter, see Using the power meter and power The computer takes the following actions for a critical battery level:

If Hibernation is disabled and the computer is on or in the Sleep state, the computer remains briefly in the Sleep state and then shuts down and loses any unsaved information. If Hibernation is enabled and the computer is on or in the Sleep state, the computer initiates Hibernation. Running on battery power 39 Resolving a low battery level Resolving a low battery level when external power is available Connect one of the following to the computer and to external power:

AC adapter Optional docking or expansion device Optional power adapter purchased as an accessory from HP Resolving a low battery level when no power source is available Save your work and shut down the computer. Resolving a low battery level when the computer cannot exit Hibernation 1. 2. Connect the AC adapter to the computer and to external power. Exit Hibernation by pressing the power button. Running on AC power For information about connecting to AC power, refer to the Setup Instructions poster provided in the computer box. The computer does not use battery power when the computer is connected to AC power with an approved AC adapter or an optional docking/expansion device. WARNING! To reduce potential safety issues, use only the AC adapter provided with the computer, a replacement AC adapter provided by HP, or a compatible AC adapter purchased from HP. Connect the computer to AC power under any of the following conditions:

WARNING! Do not charge the computer battery while you are aboard aircraft. When charging or calibrating a battery When installing or modifying system software When writing information to a disc (select products only) When running Disk Defragmenter on computers with internal hard drives When performing a backup or recovery When you connect the computer to AC power:

The battery begins to charge. The screen brightness increases. The power meter icon changes appearance. When you disconnect AC power:

40 Chapter 6 Managing power The computer switches to battery power. The screen brightness automatically decreases to save battery life. The power meter icon changes appearance. Troubleshooting power problems Test the AC adapter if the computer exhibits any of the following symptoms when it is connected to AC power:

The computer does not turn on. The display does not turn on. The power lights do not turn on. To test the AC adapter:

1. 2. 3. Shut down the computer. Connect the AC adapter to the computer and to the power cord, and then plug the power cord into an AC outlet. Turn on the computer. If the power lights turn on, the AC adapter is working properly. If the power lights remain off, check the connection from the AC adapter to the computer and the connection from the power cord to the AC outlet to be sure that the connections are secure. If the connections are secure and the power lights remain off, the AC adapter is not functioning and should be replaced. Contact support for information about obtaining a replacement AC power adapter. Shutting down (turning off) the computer CAUTION: Unsaved information is lost when the computer shuts down. Be sure to save your work before shutting down the computer. The Shut down command closes all open programs, including the operating system, and then turns off the display and computer. Shut down the computer under any of the following conditions:

When you need to access components inside the computer When you are connecting an external hardware device that does not connect to a USB or video port When the computer will be unused and disconnected from external power for an extended period Although you can turn off the computer with the power button, the recommended procedure is to use the Windows Shut down command. NOTE:

pressing the power button. If the computer is in the Sleep state or in Hibernation, first exit Sleep or Hibernation by briefly 1. 2. Save your work and close all open programs. Select the Start button, select the Power icon, and then select Shut down. Shutting down (turning off) the computer 41 If the computer is unresponsive and you are unable to use the preceding shutdown procedures, try the following emergency procedures in the sequence provided:

Press ctrl+alt+delete, select the Power icon, and then select Shut down. Press and hold the power button for at least 5 seconds. Disconnect the computer from external power. 42 Chapter 6 Managing power 7 Maintaining your computer It is important to perform regular maintenance to keep your computer in optimal condition. This chapter explains how to use tools like Disk Defragmenter and Disk Cleanup. It also provides instructions for updating programs and drivers, steps to clean the computer, and tips for traveling with (or shipping) the computer. Improving performance You can improve the performance of your computer by performing regular maintenance tasks with tools such as Disk Defragmenter and Disk Cleanup. Using Disk Defragmenter HP recommends using Disk Defragmenter to defragment your hard drive at least once a month. NOTE:

It is not necessary to run Disk Defragmenter on solid-state drives. To run Disk Defragmenter:

1. 2. Connect the computer to AC power. Type defragment in the taskbar search box, and then select Defragment and optimize your drives. Follow the on-screen instructions. 3. For additional information, access the Disk Defragmenter software Help. Using Disk Cleanup Use Disk Cleanup to search the hard drive for unnecessary files that you can safely delete to free up disk space and help the computer run more efficiently. To run Disk Cleanup:

1. Type disk in the taskbar search box, and then select Free up disk space by deleting unnecessary files or Uninstall apps to free up disk space. Follow the on-screen instructions. 2. Using HP 3D DriveGuard (select products only) HP 3D DriveGuard protects a hard drive by parking the drive and halting data requests under either of the following conditions:

You drop the computer. You move the computer with the display closed while the computer is running on battery power. A short time after the end of one of these events, HP 3D DriveGuard returns the hard drive to normal operation. NOTE: Only internal hard drives are protected by HP 3D DriveGuard. A hard drive installed in an optional docking device or connected to a USB port is not protected by HP 3D DriveGuard. Improving performance 43 NOTE: Because solid-state drives (SSDs) lack moving parts, HP 3D DriveGuard is unnecessary for these drives. For more information, see the HP 3D DriveGuard software Help. Identifying HP 3D DriveGuard status The hard drive light on the computer changes color to show that the drive in a primary hard drive bay and/or the drive in a secondary hard drive bay (select products only) is parked. To determine whether a drive is currently protected or whether it is parked, view the icon on the Windows desktop in the notification area, at the far right of the taskbar. Updating programs and drivers HP recommends that you update your programs and drivers on a regular basis. Updates can resolve issues and bring new features and options to your computer. For example, older graphics components might not work well with the most recent gaming software. Without the latest driver, you would not be getting the most out of your equipment. Go to http://www.hp.com/support to download the latest versions of HP programs and drivers. In addition, register to receive automatic notifications when updates become available. If you would like to update your programs and drivers, follow these instructions:

1. Type support in the taskbar search box, and then select the HP Support Assistant app.

- or -

Click the question mark icon in the taskbar. Select My PC, select the Updates tab, and then select Check for updates and messages. Follow the on-screen instructions. 2. 3. Cleaning your computer Use the following products to safely clean your computer:

Dimethyl benzyl ammonium chloride 0.3 percent maximum concentration (for example, disposable wipes, which come in a variety of brands) Alcohol-free glass-cleaning fluid Solution of water and mild soap Dry microfiber cleaning cloth or a chamois (static-free cloth without oil) Static-free cloth wipes CAUTION: Avoid strong cleaning solvents that can permanently damage your computer. If you are not sure that a cleaning product is safe for your computer, check the product contents to make sure that ingredients such as alcohol, acetone, ammonium chloride, methylene chloride, and hydrocarbons are not included in the product. Fibrous materials, such as paper towels, can scratch the computer. Over time, dirt particles and cleaning agents can get trapped in the scratches. Cleaning procedures Follow the procedures in this section to safely clean your computer. 44 Chapter 7 Maintaining your computer WARNING! To prevent electric shock or damage to components, do not attempt to clean your computer while it is on. 1. 2. 3. CAUTION: To prevent damage to internal components, do not spray cleaning agents or liquids directly on any computer surface. Liquids dripped on the surface can permanently damage internal components. Turn off the computer. Disconnect AC power. Disconnect all powered external devices. Cleaning the display Gently wipe the display using a soft, lint-free cloth moistened with an alcohol-free glass cleaner. Be sure that a display is dry before you close the computer. Cleaning the sides or cover To clean the sides or cover, use a soft microfiber cloth or chamois moistened with one of the cleaning solutions listed previously, or use an acceptable disposable wipe. NOTE: When cleaning the cover of the computer, use a circular motion to aid in removing dirt and debris. Cleaning the TouchPad, keyboard, or mouse (select products only) WARNING! To reduce the risk of electric shock or damage to internal components, do not use a vacuum cleaner attachment to clean the keyboard. A vacuum cleaner can deposit household debris on the keyboard surface. CAUTION: To prevent damage to internal components, do not allow liquids to drip between the keys. To clean the TouchPad, keyboard, or mouse, use a soft microfiber cloth or a chamois moistened with one of the cleaning solutions listed previously or use an acceptable disposable wipe. To prevent keys from sticking and to remove dust, lint, and particles from the keyboard, use a can of compressed air with a straw extension. Traveling with or shipping your computer If you have to travel with or ship your computer, follow these tips to keep your equipment safe. Prepare the computer for traveling or shipping:

Back up your information to an external drive. Remove all discs and all external media cards, such as memory cards. Turn off and then disconnect all external devices. Shut down the computer. Take along a backup of your information. Keep the backup separate from the computer. When traveling by air, carry the computer as hand luggage; do not check it in with the rest of your luggage. CAUTION: Avoid exposing a drive to magnetic fields. Security devices with magnetic fields include airport walk-through devices and security wands. Airport conveyer belts and similar security devices that check carry-on baggage use X-rays instead of magnetism and do not damage drives. Traveling with or shipping your computer 45 If you plan to use the computer during a flight, listen for the in-flight announcement that tells you when you are allowed to use your computer. In-flight computer use is at the discretion of the airline. If you are shipping the computer or a drive, use suitable protective packaging and label the package FRAGILE. The use of wireless devices may be restricted in some environments. Such restrictions may apply aboard aircraft, in hospitals, near explosives, and in hazardous locations. If you are uncertain of the policy that applies to the use of a wireless device in your computer, ask for authorization to use your computer before you turn it on. If you are traveling internationally, follow these suggestions:

Check the computer-related customs regulations for each country or region on your itinerary. Check the power cord and adapter requirements for each location in which you plan to use the computer. Voltage, frequency, and plug configurations vary. WARNING! To reduce the risk of electric shock, fire, or damage to the equipment, do not attempt to power the computer with a voltage converter kit sold for appliances. 46 Chapter 7 Maintaining your computer 8 Securing your computer and information Computer security is essential for protecting the confidentiality, integrity, and availability of your information. Standard security solutions provided by the Windows operating system, HP applications, the Setup Utility

(BIOS), and other third-party software can help protect your computer from a variety of risks, such as viruses, worms, and other types of malicious code. IMPORTANT: Some security features listed in this chapter may not be available on your computer. Using passwords A password is a group of characters that you choose to secure your computer information and to protect online transactions. Several types of passwords can be set. For example, when you set up your computer for the first time, you were asked to create a user password to secure your computer. Additional passwords can be set in Windows or in HP Setup Utility (BIOS), which is preinstalled on your computer. You may find it helpful to use the same password for a Setup Utility (BIOS) feature and for a Windows security feature. To create and save passwords, use the following tips:

To reduce the risk of being locked out of the computer, record each password and store it in a secure place away from the computer. Do not store passwords in a file on the computer. When creating passwords, follow requirements set by the program. Change your passwords at least every 3 months. An ideal password is long and has letters, punctuation, symbols, and numbers. Before you send your computer for service, back up your files, delete confidential files, and then remove all password settings. For additional information about Windows passwords, such as screen-saver passwords:

Type support in the taskbar search box, and then select the HP Support Assistant app. or Click the question mark icon in the taskbar. Setting Windows passwords Password User password Administrator password Function Protects access to a Windows user account. Protects administrator-level access to computer contents. NOTE: This password cannot be used to access Setup Utility

(BIOS) contents. Using passwords 47 Setting Setup Utility (BIOS) passwords Password Administrator password Power-on password Function Must be entered each time you access Setup Utility (BIOS). If you forget your administrator password, you cannot access Setup Utility (BIOS). Must be entered each time you turn on or restart the computer. If you forget your power-on password, you cannot turn on or restart the computer. To set, change, or delete an administrator or power-on password in Setup Utility (BIOS):

CAUTION: Use extreme care when making changes in Setup Utility (BIOS). Errors can prevent the computer from operating properly. NOTE: To start Setup Utility, your computer must be in notebook mode and you must use the keyboard attached to your notebook. The on-screen keyboard, which displays in tablet mode, cannot access Setup Utility. 1. Start Setup Utility (BIOS):

Computers or tablets with keyboards:

Turn on or restart the computer, quickly press esc, and then press f10. Tablets without keyboards:

1. Turn on or restart the tablet, and then quickly hold down the volume down button.

- or -

Turn on or restart the tablet, and then quickly hold down the Windows button. Tap f10. 2. Select Security, and then follow the on-screen instructions. 2. Your changes take effect when the computer restarts. Using Windows Hello (select products only) On products equipped with a fingerprint reader or an infrared camera, you can use Windows Hello to sign in by swiping your finger or looking at the camera. To set up Windows Hello, follow these steps:

1. 2. Select the Start button, select Settings, select Accounts, and then select Sign-in options. Under Windows Hello, follow the on-screen instructions to add both a password and a 4-digit PIN, and then enroll your fingerprint or facial ID. Using Internet security software When you use your computer to access email, a network, or the Internet, you potentially expose your computer to computer viruses, spyware, and other online threats. To help protect your computer, Internet 48 Chapter 8 Securing your computer and information security software that includes antivirus and firewall features may be preinstalled on your computer as a trial offer. To provide ongoing protection against newly discovered viruses and other security risks, security software must be kept up to date. It is strongly recommended that you upgrade the security software trial offer or purchase the software of your choice in order to fully protect your computer. Using antivirus software Computer viruses can disable programs, utilities, or the operating system, or cause them to function abnormally. Antivirus software can detect most viruses, destroy them, and in most cases, repair any damage they have caused. To provide ongoing protection against newly discovered viruses, antivirus software must be kept up to date. An antivirus program may be preinstalled on your computer. It is strongly recommended that you use the antivirus program of your choice in order to fully protect your computer. For more information about computer viruses, type support in the taskbar search box, and then select the HP Support Assistant app. or Click the question mark icon in the taskbar. Using firewall software Firewalls are designed to prevent unauthorized access to a system or network. A firewall can be software you install on your computer and/or network, or it can be a combination of both hardware and software. There are two types of firewalls to consider:

Host-based firewallsSoftware that protects only the computer it is installed on. Network-based firewallsInstalled between your DSL or cable modem and your home network to protect all the computers on the network. When a firewall is installed on a system, all data sent to and from the system is monitored and compared with a set of user-defined security criteria. Any data that does not meet those criteria is blocked. Installing software updates HP, Windows, and third-party software installed on your computer should be regularly updated to correct security problems and improve software performance. CAUTION: Microsoft sends out alerts regarding Windows updates, which may include security updates. To protect the computer from security breaches and computer viruses, install all updates from Microsoft as soon as you receive an alert. You can install these updates automatically. To view or change the settings:

1. 2. 3. Select the Start button, select Settings, and then select Update & Security. Select Windows Update, and then follow the on-screen instructions. To schedule a time for installing updates, select Advanced Options, and then follow the on-screen instructions. Installing software updates 49 Using HP Touchpoint Manager (select products only) HP Touchpoint Manager is a cloud-based IT solution that enables businesses to effectively manage and secure their company assets. HP Touchpoint Manager helps protect devices against malware and other attacks, monitors device health, and enables you to reduce time spent solving end-user device and security issues. You can quickly download and install the software, which is highly cost effective relative to traditional in-house solutions. Securing your wireless network When you set up a WLAN or access an existing WLAN, always enable security features to protect your network from unauthorized access. WLANs in public areas (hotspots) like coffee shops and airports may not provide any security. Backing up your software applications and information Regularly back up your software applications and information to protect them from being permanently lost or damaged through a virus attack or a software or hardware failure. Using an optional security cable (select products only) A security cable (purchased separately) is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. To connect a security cable to your computer, follow the device manufacturer's instructions. 50 Chapter 8 Securing your computer and information 9 Using Setup Utility (BIOS) Setup Utility, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Setup Utility (BIOS) includes settings for the types of devices installed, the startup sequence of the computer, and the amount of system and extended memory. NOTE: To start Setup Utility on convertible computers, your computer must be in notebook mode and you must use the keyboard attached to your notebook. Starting Setup Utility (BIOS) CAUTION: Use extreme care when making changes in Setup Utility (BIOS). Errors can prevent the computer from operating properly. Turn on or restart the computer, quickly press esc, and then press f10. Updating Setup Utility (BIOS) Updated versions of Setup Utility (BIOS) may be available on the HP website. Most BIOS updates on the HP website are packaged in compressed files called SoftPaqs. Some download packages contain a file named Readme.txt, which contains information regarding installing and troubleshooting the file. Determining the BIOS version To decide whether you need to update Setup Utility (BIOS), first determine the BIOS version on your computer. To reveal the BIOS version information (also known as ROM date and System BIOS), use one of these options. HP Support Assistant 1. Type support in the taskbar search box, and then select the HP Support Assistant app. or Click the question mark icon in the taskbar. Select My PC, and then select Specifications. 2. Setup Utility (BIOS) 1. 2. 3. Start Setup Utility (BIOS) (see Starting Setup Utility (BIOS) on page 51). Select Main, select System Information, and then make note of the BIOS version. Select Exit, select No, and then follow the on-screen instructions. To check for later BIOS versions, see Downloading a BIOS update on page 52. Starting Setup Utility (BIOS) 51 Downloading a BIOS update CAUTION: To reduce the risk of damage to the computer or an unsuccessful installation, download and install a BIOS update only when the computer is connected to reliable external power using the AC adapter. Do not download or install a BIOS update while the computer is running on battery power, docked in an optional docking device, or connected to an optional power source. During the download and installation, follow these instructions:

Do not disconnect power from the computer by unplugging the power cord from the AC outlet. Do not shut down the computer or initiate Sleep. Do not insert, remove, connect, or disconnect any device, cable, or cord. NOTE:

software updates, especially system BIOS updates. If your computer is connected to a network, consult the network administrator before installing any 1. 2. 3. 4. Type support in the taskbar search box, and then select the HP Support Assistant app. or Click the question mark icon in the taskbar. Click Updates, and then click Check for updates and messages. Follow the on-screen instructions. At the download area, follow these steps:

a. Identify the most recent BIOS update and compare it to the BIOS version currently installed on your computer. If the update is more recent than your BIOS version, make a note of the date, name, or other identifier. You may need this information to locate the update later, after it has been downloaded to your hard drive. Follow the on-screen instructions to download your selection to the hard drive. Make a note of the path to the location on your hard drive where the BIOS update is downloaded. You will need to access this path when you are ready to install the update. b. BIOS installation procedures vary. Follow any instructions that appear on the screen after the download is complete. If no instructions appear, follow these steps:

1. Type file in the taskbar search box, and then select File Explorer. Click your hard drive designation. The hard drive designation is typically Local Disk (C:). Using the hard drive path you recorded earlier, open the folder that contains the update. Double-click the file that has an .exe extension (for example, filename.exe). The BIOS installation begins. Complete the installation by following the on-screen instructions. 2. 3. 4. 5. NOTE: After a message on the screen reports a successful installation, you can delete the downloaded file from your hard drive. 52 Chapter 9 Using Setup Utility (BIOS) 10 Using HP PC Hardware Diagnostics (UEFI) HP PC Hardware Diagnostics is a Unified Extensible Firmware Interface (UEFI) that allows you to run diagnostic tests to determine whether the computer hardware is functioning properly. The tool runs outside the operating system so that it can isolate hardware failures from issues that are caused by the operating system or other software components. When HP PC Hardware Diagnostics (UEFI) detects a failure that requires hardware replacement, a 24-digit Failure ID code is generated. This ID code can then be provided to support to help determine how to correct the problem. NOTE: To start diagnostics on a convertible computer, your computer must be in notebook mode and you must use the keyboard attached. To start HP PC Hardware Diagnostics (UEFI), follow these steps:

1. 2. Turn on or restart the computer, and quickly press esc. Press f2. The BIOS searches three places for the diagnostic tools, in the following order:

a. Connected USB drive NOTE: To download the HP PC Hardware Diagnostics (UEFI) tool to a USB drive, see Downloading HP PC Hardware Diagnostics (UEFI) to a USB device on page 53. b. c. Hard drive BIOS 3. When the diagnostic tool opens, select the type of diagnostic test you want to run, and then follow the on-screen instructions. NOTE:

If you need to stop a diagnostic test, press esc. Downloading HP PC Hardware Diagnostics (UEFI) to a USB device NOTE: The HP PC Hardware Diagnostics (UEFI) download instructions are provided in English only, and you must use a Windows computer to download and create the HP UEFI support environment because only .exe files are offered. Go to http://www.hp.com/go/techcenter/pcdiags. The HP PC Diagnostics home page is displayed. In the HP PC Hardware Diagnostics section, select the Download link, and then select Run. There are two options to download HP PC Hardware Diagnostics to a USB device. Download the latest UEFI version 1. 2. Download any version of UEFI for a specific product 1. 2. Go to http://www.hp.com/support. Select Get software and drivers. Downloading HP PC Hardware Diagnostics (UEFI) to a USB device 53 3. 4. 5. Enter the product name or number. or Select Identify now to let HP automatically detect your product. Select your computer, and then select your operating system. In the Diagnostic section, follow the on-screen instructions to select and download the UEFI version you want. 54 Chapter 10 Using HP PC Hardware Diagnostics (UEFI) 11 Backing up, restoring, and recovering This chapter provides information about the following processes. The information in the chapter is standard procedure for most products. Creating recovery media and backups Restoring and recovering your system For additional information, refer to the HP support assistant app. Type support in the taskbar search box, and then select the HP Support Assistant app. or Click the question mark icon in the taskbar. If you will be performing recovery procedures on a tablet, the tablet battery must be at least IMPORTANT:

70% charged before you start the recovery process. IMPORTANT:

beginning any recovery process. For a tablet with a detachable keyboard, connect the keyboard to the keyboard dock before Creating recovery media and backups The following methods of creating recovery media and backups are available on select products only. Choose the available method according to your computer model. Use HP Recovery Manager to create HP Recovery media after you successfully set up the computer. This step creates a backup of the HP Recovery partition on the computer. The backup can be used to reinstall the original operating system in cases where the hard drive is corrupted or has been replaced. For information on creating recovery media, see Creating HP Recovery media (select products only) on page 55. For information on the recovery options that are available using the recovery media, see Using Windows tools on page 56. Use Windows tools to create system restore points and create backups of personal information. For more information, see Recovering using HP Recovery Manager on page 57. NOTE:

If storage is 32 GB or less, Microsoft System Restore is disabled by default. Creating HP Recovery media (select products only) If possible, check for the presence of the Recovery partition and the Windows partition. From the Start menu, select File Explorer, and then select This PC. If your computer does not list the Windows partition and the Recovery partition, you can obtain recovery media for your system from support. See the Worldwide Telephone Numbers booklet included with the computer. You can also find contact information on the HP website. Go to http://www.hp.com/support, select your country or region, and follow the on-screen instructions. Creating recovery media and backups 55 You can use Windows tools to create system restore points and create backups of personal information, see Using Windows tools on page 56. If your computer does list the Recovery partition and the Windows partition, you can use HP Recovery Manager to create recovery media after you successfully set up the computer. HP Recovery media can be used to perform system recovery if the hard drive becomes corrupted. System recovery reinstalls the original operating system and software programs that were installed at the factory and then configures the settings for the programs. HP Recovery media can also be used to customize the system or restore the factory image if you replace the hard drive. Only one set of recovery media can be created. Handle these recovery tools carefully, and keep them in a safe place. HP Recovery Manager examines the computer and determines the required storage capacity for the media that will be required. To create recovery discs, your computer must have an optical drive with DVD writer capability, and you must use only high-quality blank DVD-R, DVD+R, DVD-R DL, or DVD+R DL discs. Do not use rewritable discs such as CDRW, DVDRW, double-layer DVDRW, or BD-RE (rewritable Blu-ray) discs; they are not compatible with HP Recovery Manager software. Or, instead, you can use a high-

quality blank USB flash drive. If your computer does not include an integrated optical drive with DVD writer capability, but you would like to create DVD recovery media, you can use an external optical drive (purchased separately) to create recovery discs. If you use an external optical drive, it must be connected directly to a USB port on the computer; the drive cannot be connected to a USB port on an external device, such as a USB hub. If you cannot create DVD media yourself, you can obtain recovery discs for your computer from HP. See the Worldwide Telephone Numbers booklet included with the computer. You can also find contact information on the HP website. Go to http://www.hp.com/

support, select your country or region, and follow the on-screen instructions. Be sure that the computer is connected to AC power before you begin creating the recovery media. The creation process can take an hour or more. Do not interrupt the creation process. If necessary, you can exit the program before you have finished creating all of the recovery DVDs. HP Recovery Manager will finish burning the current DVD. The next time you start HP Recovery Manager, you will be prompted to continue. To create HP Recovery media:

IMPORTANT:

beginning these steps. For a tablet with a detachable keyboard, connect the keyboard to the keyboard dock before 1. Type recovery in the taskbar search box, and then select HP Recovery Manager. Select Create recovery media, and then follow the on-screen instructions. 2. If you ever need to recover the system, see Recovering using HP Recovery Manager on page 57. Using Windows tools You can create recovery media, system restore points, and backups of personal information using Windows tools. NOTE:

If storage is 32 GB or less, Microsoft System Restore is disabled by default. For more information and steps, see the Get started app. Select the Start button, and then select the Get started app. 56 Chapter 11 Backing up, restoring, and recovering Restore and recovery There are several options for recovering your system. Choose the method that best matches your situation and level of expertise:

IMPORTANT: Not all methods are available on all products. Windows offers several options for restoring from backup, refreshing the computer, and resetting the computer to its original state. For more information see the Get started app. Select the Start button, and then select the Get started app. If you need to correct a problem with a preinstalled application or driver, use the Reinstall drivers and/or applications option (select products only) of HP Recovery Manager to reinstall the individual application or driver. Type recovery in the taskbar search box, select HP Recovery Manager, select Reinstall drivers and/or applications, and then follow the on-screen instructions. If you want to recover the Windows partition to original factory content, you can choose the System Recovery option from the HP Recovery partition (select products only) or use the HP Recovery media. For more information, see Recovering using HP Recovery Manager on page 57. If you have not already created recovery media, see Creating HP Recovery media (select products only) on page 55. On select products, if you want to recover the computer's original factory partition and content, or if you have replaced the hard drive, you can use the Factory Reset option of HP Recovery media. For more information, see Recovering using HP Recovery Manager on page 57. On select products, if you want to remove the recovery partition to reclaim hard drive space, HP Recovery Manager offers the Remove Recovery Partition option. For more information, see Removing the HP Recovery partition (select products only) on page 60. Recovering using HP Recovery Manager HP Recovery Manager software allows you to recover the computer to its original factory state by using the HP Recovery media that you either created or that you obtained from HP, or by using the HP Recovery partition (select products only). If you have not already created recovery media, see Creating HP Recovery media (select products only) on page 55. What you need to know before you get started HP Recovery Manager recovers only software that was installed at the factory. For software not provided with this computer, you must either download the software from the manufacturer's website or reinstall the software from the media provided by the manufacturer. IMPORTANT: Recovery through HP Recovery Manager should be used as a final attempt to correct computer issues. HP Recovery media must be used if the computer hard drive fails. If you have not already created recovery media, see Creating HP Recovery media (select products only) on page 55. To use the Factory Reset option (select products only), you must use HP Recovery media. If you have not already created recovery media, see Creating HP Recovery media (select products only) on page 55. If your computer does not allow the creation of HP Recovery media or if the HP Recovery media does not work, you can obtain recovery media for your system from support. See the Worldwide Telephone Numbers booklet included with the computer. You can also find contact information from the HP Restore and recovery 57 website. Go to http://www.hp.com/support, select your country or region, and follow the on-screen instructions. IMPORTANT: HP Recovery Manager does not automatically provide backups of your personal data. Before beginning recovery, back up any personal data you want to retain. Using HP Recovery media, you can choose from one of the following recovery options:

NOTE: Only the options available for your computer display when you start the recovery process. System RecoveryReinstalls the original operating system, and then configures the settings for the programs that were installed at the factory. Factory ResetRestores the computer to its original factory state by deleting all information from the hard drive and re-creating the partitions. Then it reinstalls the operating system and the software that was installed at the factory. The HP Recovery partition (select products only) allows System Recovery only. Using the HP Recovery partition (select products only) The HP Recovery partition allows you to perform a system recovery without the need for recovery discs or a recovery USB flash drive. This type of recovery can be used only if the hard drive is still working. To start HP Recovery Manager from the HP Recovery partition:

IMPORTANT:

beginning these steps (select products only). For a tablet with a detachable keyboard, connect the keyboard to the keyboard dock before 1. 2. 3. Type recovery in the taskbar search box, select Recovery Manager, and then select HP Recovery Environment.

- or-

For computers or tablets with keyboards attached, press f11 while the computer boots, or press and hold f11 as you press the power button. For tablets without keyboards:

Turn on or restart the tablet, and then quickly hold down the volume down button; then select f11.

- or -

Turn on or restart the tablet, and then quickly hold down the Windows button; then select f11. Select Troubleshoot from the boot options menu. Select Recovery Manager, and then follow the on-screen instructions. Using HP Recovery media to recover You can use HP Recovery media to recover the original system. This method can be used if your system does not have an HP Recovery partition or if the hard drive is not working properly. 1. 2. If possible, back up all personal files. Insert the HP Recovery media, and then restart the computer. NOTE:

boot order. See Changing the computer boot order on page 59. If the computer does not automatically restart in HP Recovery Manager, change the computer 3. Follow the on-screen instructions. 58 Chapter 11 Backing up, restoring, and recovering Changing the computer boot order If your computer does not restart in HP Recovery Manager, you can change the computer boot order, which is the order of devices listed in BIOS where the computer looks for startup information. You can change the selection to an optical drive or a USB flash drive. To change the boot order:

IMPORTANT:

beginning these steps. For a tablet with a detachable keyboard, connect the keyboard to the keyboard dock before 1. 2. Insert the HP Recovery media. Access BIOS:

For computers or tablets with keyboards attached:

Turn on or restart the computer or tablet, quickly press esc, and then press f9 for boot options. For tablets without keyboards:

Turn on or restart the tablet, and then quickly hold down the volume down button; then select f9.

- or -

Turn on or restart the tablet, and then quickly hold down the Windows button; then select f9. 3. 4. Select the optical drive or USB flash drive from which you want to boot. Follow the on-screen instructions. Restore and recovery 59 Removing the HP Recovery partition (select products only) HP Recovery Manager software allows you to remove the HP Recovery partition to free up hard drive space. IMPORTANT: After you remove the HP Recovery partition, you will not be able to perform System Recovery or create HP recovery media from the HP Recovery partition. So before you remove the Recovery partition, create HP Recovery media; see Creating HP Recovery media (select products only) on page 55. NOTE: The Remove Recovery Partition option is only available on products that support this function. Follow these steps to remove the HP Recovery partition:

1. Type recovery in the taskbar search box, and then select HP Recovery Manager. Select Remove Recovery Partition, and then follow the on-screen instructions. 2. 60 Chapter 11 Backing up, restoring, and recovering 12 Specifications Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100240 V, 5060 Hz. Although the computer can be powered from a standalone DC power source, it should be powered only with an AC adapter or a DC power source that is supplied and approved by HP for use with this computer. The computer can operate on DC power within the following specifications. Operating voltage and current varies by platform. The voltage and current for your computer is located on the regulatory label. Input power Rating Operating voltage and current 5 V dc @ 2 A / 12 V dc @ 3 A /15 V dc @ 3 A 45 W USB-C 5 V dc @ 3 A / 9 V dc @ 3 A / 10 V dc @ 3.75 A / 12 V dc @ 3.75 A / 15 V dc @ 3 A / 20 V dc @ 2.25 A 45 W USB-C 5 V dc @ 3 A / 9 V dc @ 3A / 10 V dc @ 5.0 A / 12 V dc @ 5.0 A / 15 V dc @ 4.33 A / 20 V dc @ 3.25 A 65 W USB-C 5 V dc @ 3 A / 9 V dc @ 3 A / 10 V dc @ 5.0 A / 12 V dc @ 5.0 A / 15 V dc @ 5.0 A / 20 V dc @ 4.5 A 90 W USB-C 19.5 V dc @ 2.31 A 45 W 19.5 V dc @ 3.33 A 65 W 19.5 V dc @ 4.62 A 90 W 19.5 V dc @ 6.15 A 120 W 19.5 V dc @ 7.70 A 150 W 19.5 V dc @ 10.3A 200 W DC plug of external HP power supply (select products only) NOTE: This product is designed for IT power systems in Norway with phase-to-phase voltage not exceeding 240 V rms. Operating environment Factor Temperature Operating Metric U.S. 5C to 35C 41F to 95F Input power 61 Nonoperating

-20C to 60C

-4F to 140F Relative humidity (noncondensing) Operating Nonoperating Maximum altitude (unpressurized) Operating Nonoperating 10% to 90%

5% to 95%

-15 m to 3,048 m

-15 m to 12,192 m 10% to 90%

5% to 95%

-50 ft to 10,000 ft

-50 ft to 40,000 ft 62 Chapter 12 Specifications 13 Electrostatic Discharge Electrostatic discharge is the release of static electricity when two objects come into contactfor example, the shock you receive when you walk across the carpet and touch a metal door knob. A discharge of static electricity from fingers or other electrostatic conductors may damage electronic components. To prevent damage to the computer, damage to a drive, or loss of information, observe these precautions:

If removal or installation instructions direct you to unplug the computer, first be sure that it is properly grounded. Keep components in their electrostatic-safe containers until you are ready to install them. Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible. Use nonmagnetic tools. Before handling components, discharge static electricity by touching an unpainted metal surface. If you remove a component, place it in an electrostatic-safe container. 63 14 Accessibility HP designs, produces, and markets products and services that can be used by everyone, including people with disabilities, either on a stand-alone basis or with appropriate assistive devices. Supported assistive technologies HP products support a wide variety of operating system assistive technologies and can be configured to work with additional assistive technologies. Use the Search feature on your device to locate more information about assistive features. NOTE:

for that product. For additional information about a particular assistive technology product, contact customer support Contacting support We are constantly refining the accessibility of our products and services and welcome feedback from users. If you have an issue with a product or would like to tell us about accessibility features that have helped you, please contact us at +1 (888) 259-5707, Monday through Friday, 6 a.m. to 9 p.m. North American Mountain Time. If you are deaf or hard-of-hearing and use TRS/VRS/WebCapTel, contact us if you require technical support or have accessibility questions by calling +1 (877) 656-7058, Monday through Friday, 6 a.m. to 9 p.m. North American Mountain Time. NOTE: Support is in English only. 64 Chapter 14 Accessibility Index A AC adapter and battery 5, 6 AC adapter, testing 41 accessibility 64 action keys 20 identifying 19 airplane mode 23 airplane mode key 20, 23 antivirus software, using 49 audio 28 audio-out (headphone)/audio-in

(microphone) jack, identifying 8, 9 B backing up software and information 50 backups 55 battery conserving power 39 discharging 39 factory-sealed 38 finding information 39 low battery levels 39 resolving low battery level 40 battery information, finding 39 battery power 38 best practices 1 BIOS determining version 51 downloading an update 52 starting the Setup Utility 51 updating 51 Bluetooth device 23, 25 Bluetooth label 22 boot order changing 59 bottom 22 buttons left TouchPad 16 power 7, 8 right TouchPad 16 volume 8, 9 C caps lock light, identifying 17 caring for your computer 44 cleaning your computer 44 components bottom 21 display 11 left side 7 right side 5 top 16 connecting to a WLAN 24 connector, power 5, 6 corporate WLAN connection 24 critical battery level 39 D Disk Cleanup software 43 Disk Defragmenter software 43 drive light 8, 9 E electrostatic discharge 63 esc key, identifying 19 external AC power, using 40 F fingerprints, registering 48 firewall software 49 fn key, identifying 19 four-finger tap TouchPad gesture 34 G GPS 25 H HDMI port connecting 30 identifying 5, 6 HDMI, configuring audio 30 headsets, connecting 27 Hibernation exiting 37 initiated during critical battery level 39 initiating 37 high-definition devices, connecting 30, 31 HP 3D DriveGuard 43 HP Apps Store, visiting 1 HP Mobile Broadband activating 24 IMEI number 24 MEID number 24 HP PC Hardware Diagnostics (UEFI) using 53 HP Recovery Manager correcting boot problems 59 starting 58 HP Recovery media creating 55 recovery 58 HP Recovery partition recovery 58 removing 60 HP resources 2 HP Touchpoint Manager 50 I IMEI number 24 infrared camera, identifying 12 infrared webcam lights, identifying 12 initiating Sleep and Hibernation 36 input power 61 installing optional security cable 50 integrated numeric keypad, identifying 19, 35 internal microphones, identifying 11, 12 Internet security software, using 48 J jacks audio-out (headphone)/audio-in

(microphone) 8, 9 K keyboard and optional mouse using 35 Index 65 keys action 19 airplane mode 20 esc 19 fn 19 Windows 19 L labels Bluetooth 22 regulatory 22 serial number 22 service 22 wireless certification 22 WLAN 22 lights AC adapter and battery light 5, 6 caps lock 17 drive 8, 9 mute 17 power 7, 9 locating information hardware 4 software 4 low battery level 39 M maintenance Disk Cleanup 43 Disk Defragmenter 43 HP 3D DriveGuard 43 updating programs and drivers 44 managing power 36 MEID number 24 memory card reader, identifying 5, 6 memory card, identifying 5, 6 minimized image recovery 58 minimized image, creating 57 Miracast 31 mobile broadband activating 24 IMEI number 24 MEID number 24 mute light, identifying 17 N num lock key, identifying 35 O one-finger slide touch screen gesture 34 operating environment 61 original system recovery 57 P passwords Setup Utility (BIOS) 48 Windows 47 ports HDMI 5, 6, 30 Miracast 31 USB 2.0 9 USB 3.0 6, 7 USB 3.0 charging 5 USB Type-C 5, 29 power AC 40 battery 38 power button, identifying 7, 8 power connector, identifying 5, 6 power lights, identifying 7, 9 power meter, using 38 power settings, using 38 product name and number, computer 22 public WLAN connection 24 R recover options 57 recovery discs 56, 58 HP Recovery Manager 57 media 58 starting 58 supported discs 56 system 57 USB flash drive 58 using HP Recovery media 56 recovery media creating 55 creating using HP Recovery Manager 56 recovery partition removing 60 regulatory information regulatory label 22 wireless certification labels 22 S security cable slot, identifying 7, 9 security cable, installing 50 serial number 22 serial number, computer 22 service labels, locating 22 setting password protection on wakeup 37 Setup Utility (BIOS) passwords 48 shipping the computer 45 shutdown 41 Sleep exiting 37 initiating 37 Sleep and Hibernation initiating 36 slots memory card reader 5, 6 security cable 7, 9 software Disk Cleanup 43 Disk Defragmenter 43 HP 3D DriveGuard 43 software updates, installing 49 sound settings, using 28 speakers connecting 27 identifying 18 supported discs, recovery 56 system recovery 57 system restore point creating 56 system restore point, creating 55 T tap TouchPad and touch screen gesture 32 testing an AC adapter 41 three-finger swipe TouchPad gesture 34 touch screen gestures one-finger slide 34 TouchPad buttons 16 using 32 TouchPad and touch screen gestures tap 32 two-finger pinch zoom 33 TouchPad gestures four-finger tap 34 66 Index wireless controls button 23 operating system 23 wireless light 23 wireless network (WLAN) connecting 24 corporate WLAN connection 24 functional range 24 public WLAN connection 24 wireless network, securing 50 WLAN antennas, identifying 11, 12 WLAN device 22 WLAN label 22 WWAN device 24 three-finger swipe 34 two-finger scroll 33 two-finger tap 33 TouchPad zone, identifying 16 traveling with the computer 22, 45 turning off the computer 41 two-finger pinch zoom TouchPad and touch screen gesture 33 two-finger scroll TouchPad gesture 33 two-finger tap TouchPad gesture 33 U unresponsive system 41 updating programs and drivers 44 USB 2.0 port, identifying 9 USB 3.0 charging port, identifying 5 USB 3.0 port, identifying 6, 7 USB Type-C port, connecting 29 USB Type-C port, identifying 5 using external AC power 40 using passwords 47 using power meter settings 38 using power settings 38 using sound settings 28 using the integrated numeric keypad 35 using the keyboard and optional mouse 35 using the TouchPad 32 V vents, identifying 21 video 28 volume buttons, identifying 8, 9 W webcam identifying 11, 12 using 27 webcam light, identifying 11, 12 Windows system restore point 55, 56 Windows Hello using 48 Windows key, identifying 19 Windows passwords 47 Windows tools using 56 wireless button 23 wireless certification label 22 Index 67

Regulatory, Safety and Environmental Notices User Guide Copyright 2014 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. ENERGY STAR and the ENERGY STAR mark are registered trademarks owned by the U.S. Environmental Protection Agency. Java is a trademark of Sun Microsystems. Microsoft and Windows are U.S. registered trademarks of the Microsoft group of companies. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Second Edition: October 2014 First Edition: June 2014 Document Part Number: 786097-002 About This Guide This guide provides regulatory, safety and environmental information that is compliant with U.S., Canadian, and international regulations for notebook computers, desktops, thin clients and personal workstations. WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. NOTE: Text set off in this manner provides important supplemental information. iii iv About This Guide Table of contents 1 Regulatory notices for notebook computers .................................................................................................... 1 Accessing regulatory labels .................................................................................................................................. 1 Federal Communications Commission notice ....................................................................................................... 2 Modifications ....................................................................................................................................... 2 Cables .................................................................................................................................................. 2 Declaration of Conformity for products marked with the FCC logo (United States only) ................. 3 Products with wireless LAN devices or HP Mobile Broadband Modules ............................................ 3 Brazil notice ........................................................................................................................................................... 3 Canada notices ....................................................................................................................................................... 4 European Union regulatory notices ...................................................................................................................... 4 Declaration of Conformity ................................................................................................................... 4 Products with wireless functionality (EMF) ...................................................................... 5 Restrictions for product with wireless functionality ....................................................... 5 European telephone network declaration (Modem/Fax) ................................................. 5 Ergonomics notice ............................................................................................................ 5 Germany (English text) ................................................................................... 5 Germany (Deutscher text) .............................................................................. 5 Australia and New Zealand notice ......................................................................................................................... 6 Japan notice ........................................................................................................................................................... 6 Wireless LAN, Wireless WAN, and Bluetooth certification markings ................................................. 6 South Korea notices ............................................................................................................................................... 6 Mexico notice ......................................................................................................................................................... 6 Singapore wireless notice ..................................................................................................................................... 7 Thailand WWAN wireless notice ............................................................................................................................ 7 Taiwan NCC notices ................................................................................................................................................ 7 Wireless LAN 802.11a devices ............................................................................................................ 7 Wireless LAN 802.11 devices/Bluetooth devices/Short range devices ............................................. 8 Airline travel notice ................................................................................................................................................ 8 User-replaceable battery notices .......................................................................................................................... 8 Factory-sealed battery notices ............................................................................................................................. 8 Laser compliance ................................................................................................................................................... 9 Modem notices ....................................................................................................................................................... 9 Telecommunications device approvals .............................................................................................. 9 U.S. modem statements ................................................................................................................... 10 U.S. modem declarations .................................................................................................................. 11 Canada modem statements .............................................................................................................. 12 v Japan modem statements ................................................................................................................ 12 New Zealand modem statements ..................................................................................................... 12 Voice support .................................................................................................................. 13 Power cord notice ................................................................................................................................................ 13 Japan power cord notice ................................................................................................................... 13 DC plug of external HP power supply ............................................................................................... 13 Macrovision Corporation notice .......................................................................................................................... 13 2 Regulatory notices for desktops, thin clients and personal workstations ........................................................ 14 Modem notices .................................................................................................................................................... 14 Telecommunications device approvals ............................................................................................ 14 U.S. modem statements ................................................................................................................... 14 Canadian modem statements ........................................................................................................... 15 Japanese modem statements .......................................................................................................... 15 New Zealand modem statements ..................................................................................................... 16 Voice support .................................................................................................................. 16 Electromagnetic compatibility notices ............................................................................................................... 16 Federal Communications Commission notice .................................................................................. 17 Modifications ................................................................................................................... 17 Cables .............................................................................................................................. 17 Declaration of conformity for products marked with the FCC logo (United States only) ................................................................................................................................ 17 Products with wireless LAN devices ............................................................................... 17 Australia telecom statement ............................................................................................................ 18 Brazil notice ....................................................................................................................................... 19 Canadian notice ................................................................................................................................. 19 European Union regulatory notices .................................................................................................. 19 Declaration of Conformity .............................................................................................. 19 Products with wireless functionality (EMF) ................................................. 19 Restrictions for product with wireless functionality ................................... 20 European telephone network declaration (Modem/Fax) ............................ 20 Ergonomics notice ........................................................................................ 20 Japan notice ...................................................................................................................................... 20 Wireless LAN and Bluetooth certification markings ...................................................... 20 South Korea notices .......................................................................................................................... 20 Mexico notice ..................................................................................................................................... 21 Taiwan NCC notices ........................................................................................................................... 21 Wireless LAN 802.11a devices ........................................................................................ 21 Wireless LAN 802.11 devices/Bluetooth devices/Short range devices ......................... 22 vi 3 Safety notices for notebook computers ......................................................................................................... 23 Heat-related safety warning notice .................................................................................................................... 23 Potential safety conditions notice ...................................................................................................................... 23 User-replaceable battery notices ....................................................................................................................... 23 Headset and earphone volume level notice ....................................................................................................... 24 Power cord notices .............................................................................................................................................. 24 Brazil notice ....................................................................................................................................... 24 Cleaning the keyboard ......................................................................................................................................... 24 Travel notice ........................................................................................................................................................ 24 China safety notices ............................................................................................................................................ 25 China: Altitude notice ........................................................................................................................ 25 China: Tropical warning notice .......................................................................................................... 25 Norway and Sweden: Cable grounding notice for products with a TV tuner ...................................................... 25 Taiwan BSMI notice .............................................................................................................................................. 25 4 Safety notices for desktops, thin clients and personal workstations ............................................................... 26 Important safety information ............................................................................................................................. 26 Installation conditions ......................................................................................................................................... 26 Battery replacement notice ................................................................................................................................ 27 Headset and earphone volume level notice ....................................................................................................... 27 Laser safety ......................................................................................................................................................... 28 Power supply and power cord set requirements ................................................................................................ 28 Power supply class I grounding requirements ................................................................................. 28 Brazil notice .................................................................................................................... 28 Denmark .......................................................................................................................... 28 Finland ............................................................................................................................. 28 Norway ............................................................................................................................ 28 Sweden ............................................................................................................................ 28 Power supply requirements .............................................................................................................. 28 For use in Norway ........................................................................................................... 29 Power cord set requirements ........................................................................................................... 29 Japan power cord requirements ....................................................................................................... 29 Pinch hazard ........................................................................................................................................................ 29 TV antenna connectors protection ...................................................................................................................... 30 External television antenna grounding ............................................................................................ 30 Lightning protection .......................................................................................................................... 30 Note to CATV system installer .......................................................................................................... 30 China safety notices ............................................................................................................................................ 31 China: Altitude notice ........................................................................................................................ 31 China: Tropical warning notice .......................................................................................................... 31 Germany acoustics notice ................................................................................................................................... 32 vii Taiwan BSMI notice .............................................................................................................................................. 32 5 Environmental notices for notebook computers ............................................................................................ 33 Electronic hardware, packaging and battery recycling ...................................................................................... 33 Disposal of waste equipment by users ............................................................................................................... 33 Brazil alkaline battery disposal ........................................................................................................................... 33 Brazil hardware recycling information ............................................................................................................... 34 ENERGY STAR Certification (select models only) .............................................................................................. 34 Chemical substances ........................................................................................................................................... 35 China environmental notices ............................................................................................................................... 35 China PC energy label .......................................................................................................................................... 35 China restriction of hazardous substances (RoHS) ............................................................................................. 38 India restriction of hazardous substances (RoHS) .............................................................................................. 41 Japan restriction of hazardous substances (RoHS) ............................................................................................ 41 Mexico Sustainable Energy Use Law ................................................................................................................... 41 Turkey EEE regulation ......................................................................................................................................... 41 Ukraine restriction of hazardous substances (RoHS) ......................................................................................... 41 Perchlorate materialspecial handling may apply ........................................................................................... 41 6 Environmental notices for desktops, thin clients and personal workstations ................................................... 42 Electronic hardware, packaging and battery recycling ...................................................................................... 42 Disposal of waste equipment by users ............................................................................................................... 42 Brazil alkaline battery disposal ........................................................................................................................... 42 Brazil hardware recycling information ............................................................................................................... 43 ENERGY STAR Certification (select models only) .............................................................................................. 43 Chemical substances ........................................................................................................................................... 44 Mercury statement .............................................................................................................................................. 44 Perchlorate materialspecial handling may apply ............................................................................................. 44 China environmental notices ............................................................................................................................... 44 China PC energy label .......................................................................................................................................... 45 China restriction of hazardous substances (RoHS) ............................................................................................. 48 The Table of Hazardous Substances/Elements and their Content .................................................. 49 India restriction of hazardous substances (RoHS) .............................................................................................. 50 IT ECO declarations .............................................................................................................................................. 50 Japan restriction of hazardous substances (RoHS) ............................................................................................ 50 Ley para el Aprovechamiento Sustentable de la Energa de Mxico (Mexico Sustainable Energy Use Law) .... 50 Turkey EEE regulation ......................................................................................................................................... 51

(Ukraine restriction of hazardous substances

(RoHS)) ................................................................................................................................................................. 51 TCO Certified Edge Certification .......................................................................................................................... 51 viii Index ............................................................................................................................................................. 53 ix x 1 Regulatory notices for notebook computers This chapter provides country- and region-specific non-wireless and wireless regulatory notices and compliance information for the computer product. Some of these notices may not apply to your product. One or more integrated wireless devices may be installed. In some environments, the use of wireless devices may be restricted. Such restrictions may apply onboard airplanes, in hospitals, near explosives, in hazardous locations, and so on. If you are uncertain of the policy that applies to the use of this product, ask for authorization to use it before you turn it on. Accessing regulatory labels Regulatory labels, which provide country or regional regulatory information (for example, FCC ID), may be physically located on the bottom of the computer, inside the battery bay (select models only), under the removable service door (select models only), on the back of the display, or on the wireless or modem module. Some products may also provide electronic regulatory labels (e-labels) for radio modules in your computer. Electronic labels can be accessed through the system BIOS. NOTE: Electronic labels are not available on all products. NOTE: Devices not for sale or use in the United States may not contain a FCC ID. To view electronic regulatory labels:

1. 2. 3. 4. Turn on or restart the computer, and then press esc while the Press the ESC key for Startup Menu message is displayed at the bottom of the screen. Press f10 to enter Computer Setup. Use a pointing device or the arrow keys to select Advanced, select Electronic Labels, and then press enter. To view an electronic label, use a pointing device or the arrow keys to select one of the listed items, and then press OK. NOTE: The list of available electronic label items varies depending on the computer model and installed devices. 5. To exit Computer Setup menus without saving your changes:

Select the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions. or Use the arrow keys to select Main, select Ignore Changes and Exit, and then press enter. Accessing regulatory labels 1 Federal Communications Commission notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio or television technician for help. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by HP may void the user's authority to operate the equipment. Cables To maintain compliance with FCC Rules and Regulations, connections to this device must be made with shielded cables having metallic RFI/EMI connector hoods. 2 Chapter 1 Regulatory notices for notebook computers Declaration of Conformity for products marked with the FCC logo (United States only) This device complies with Part 15 of the FCC Rules. Operation is subject to the following 2 conditions:

1. 2. This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. If you have questions about the product that are not related to this declaration, write to Hewlett-Packard Company P. O. Box 692000, Mail Stop 530113 Houston, TX 77269-2000 For questions regarding this FCC declaration, write to Hewlett-Packard Company P. O. Box 692000, Mail Stop 510101 Houston, TX 77269-2000 or call HP at 281-514-3333 To identify your product, refer to the part, series, or model number located on the product. Products with wireless LAN devices or HP Mobile Broadband Modules This device must not be co-located or operating in conjunction with any other antenna or transmitter. WARNING! Exposure to Radio Frequency Radiation The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact is minimized during normal operation of tablet PCs and notebook computers. During normal operation of tablet PCs and notebook computers with displays equal to or less than 30.5 cm

(12 inches): To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antennas should not be less than 2.5 cm (1 inch). To identify the location of the wireless antennas, refer to the computer user guides included with your computer. During normal operation of notebook computers with displays greater than 30.5 cm (12 inches): To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antennas should not be less than 20 cm (8 inches), including when the computer display is closed. To identify the location of the wireless antennas, refer to the computer user guides included with your computer. CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15- to 5.25-GHz frequency range. The FCC requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel mobile satellite systems. High-power radar is allocated as the primary user of the 5.25- to 5.35-GHz and 5.65- to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device. Brazil notice Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio. Brazil notice 3 Este equipamento atende aos limites de Taxa de Absoro Especfica referente exposio a campos eltricos, magnticos e eletromagnticos de radiofreqncias adotados pela ANATEL. Ao operar o dispositivo a uma distncia muito prxima do seu corpo, utilize um acessrio de armazenamento no metlico para posicionar o dispositivo a uma distncia mnima de 1,5 cm do corpo. Canada notices This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations, CAN ICES-3(B)/NMB-3(B). If this device has WLAN or Bluetooth capability, the device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. WARNING! Exposure to Radio Frequency Radiation: The radiated output power of this device is below the Industry Canada radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact is minimized during normal operation. During normal operation of tablet PCs and notebook computers with displays equal to or less than 30.5 cm

(12 inches): To avoid the possibility of exceeding the Industry Canada radio frequency exposure limits, human proximity to the antennas should not be less than 2.5 cm (1 inch). To identify the location of the wireless antennas, refer to the computer user guides included with your computer. During normal operation of notebook computers with displays greater than 30.5 cm (12 inches): To avoid the possibility of exceeding the Industry Canada radio frequency exposure limits, human proximity to the antennas should not be less than 20 cm (8 inches), including when the computer display is closed. To identify the location of the wireless antennas, refer to the computer user guides included with your computer. CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15- to 5.25-GHz frequency range. Industry Canada requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-

channel mobile satellite systems. High-power radar is allocated as the primary user of the 5.25- to 5.35-GHz and 5.65- to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device. The antennas for this device are not replaceable. Any attempt at user access will damage your computer. European Union regulatory notices Declaration of Conformity Products bearing the CE marking comply with one or more of the following EU Directives as may be applicable:

Low Voltage Directive 2006/95/EC; EMC Directive 2004/108/EC; Ecodesign Directive 2009/125/EC; R&TTE Directive 1999/5/EC; RoHS Directive 2011/65/EU Compliance with these directives is assessed using applicable European Harmonised Standards. The full Declaration of Conformity can be found at the following web site: www.hp.eu/certificates (Search with the product model name or its Regulatory Model Number (RMN), which may be found on the regulatory label.) 4 Chapter 1 Regulatory notices for notebook computers The point of contact for regulatory matters is Hewlett-Packard GmbH, Dept./MS:HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, GERMANY. Products with wireless functionality (EMF) This product meets international guidelines (ICNIRP) for exposure to radio frequency radiation. This product incorporates a radio transmitting and receiving device. For notebook computers in normal use, a separation distance of 20 cm ensures that radio frequency exposure levels comply with EU requirements. Products designed to be operated at closer proximities, such as tablet computers, comply with applicable EU requirements in typical operating positions, but a minimum distance of 1 cm should be maintained from the antennas. Restrictions for product with wireless functionality This product is designed for use without restrictions in all EU countries, plus Iceland, Liechtenstein, Norway, and Switzerland. European telephone network declaration (Modem/Fax) The product herewith complies with the requirements of the R&TTE Directive 1999/5/EC (Annex II) and carries the CE marking accordingly. However, due to differences between the individual PSTNs provided in different countries/regions, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems, you should contact your equipment supplier in the first instance. Ergonomics notice Germany (English text) When a mobile computer is used at the office workstation for display work tasks where the Visual Display Unit (VDU) Directive 90/270/EEC is applicable, an adequate external keyboard is required. Depending on the application and task, an adequate external monitor may also be necessary to attain working conditions comparable to a workstation setup. Ref: EK1-ITB 2000 (voluntary GS certification) Mobile computers bearing the "GS" approval mark meet the applicable ergonomic requirements. Without external keyboards, they are suitable only for short-time use of VDU tasks. During mobile use with disadvantageous illumination conditions (e.g. direct sun light) reflections may occur, which result in reduced readability. Germany (Deutscher text) Wird ein mobiler Computer fr Bildschirmarbeitsaufgaben verwendet, wo die Richtlinie 90/270/EEG

(Bildschirmarbeitsrichtlinie) anzuwenden ist, wird eine geeignete externe Tastatur notwendig. Abhngig von der Anwendung und der Aufgabe kann ein geeigneter externer Monitor erforderlich sein, um vergleichbare Arbeitsbedingungen zu einem stationren Arbeitsplatz zu erreichen. Ref: EK1-ITB 2000 (freiwillige GS Zertifizierung) Mobile Computer, welche das "GS" Zeichen tragen, entsprechen den ergonomischen Anforderungen und sind nur fr kurzzeitige Benutzung von Bildschirmarbeitsaufgaben geeignet. Bei mobiler Nutzung mit ungnstigen Lichtverhltnissen (z.B. direkte Sonneneinstrahlung) kann es zu Reflexionen und damit zu Einschrnkungen der Lesbarkeit der dargestellten Zeichen kommen. European Union regulatory notices 5 Australia and New Zealand notice This equipment incorporates a radio transmitting and receiving device. In normal use, a separation distance of 20 cm ensures that radio frequency exposure levels comply with the Australian and New Zealand Standards. Japan notice Wireless LAN, Wireless WAN, and Bluetooth certification markings This product contains certified radio equipment. South Korea notices B ( )

(B) ,

.

(

).

, 2.5cm

. Mexico notice Declaracin para Mxico La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. If your product is provided with wireless accessories such as a keyboard or mouse and you need to identify the model of the accessory, refer to the label included on that accessory. 6 Chapter 1 Regulatory notices for notebook computers Singapore wireless notice Turn off any WWAN devices while you are onboard aircraft. The use of these devices onboard aircraft is illegal, may be dangerous to the operation of the aircraft, and may disrupt the cellular network. Failure to observe this instruction may lead to suspension or denial of cellular services to the offender, or legal action, or both. Users are reminded to restrict the use of radio equipment in fuel depots, chemical plants, and where blasting operations are in progress. As with other mobile radio transmitting equipment, users are advised that for satisfactory operation of the equipment and for the safety of personnel, no part of the human body should be allowed to come too close to the antennas during operation of the equipment. This device has been designed to comply with applicable requirements for exposure to radio waves, based on scientific guidelines that include margins intended to assure the safety of all people, regardless of health and age. These radio wave exposure guidelines employ a unit of measurement known as the specific absorption rate (SAR). Tests for SAR are conducted using standardized methods, with the phone transmitting at its highest certified power level in all used frequency bands. The SAR data information is based on CENELEC's standards EN50360 and EN50361, which use the limit of 2 watts per kilogram, averaged over 10 grams of tissue. Thailand WWAN wireless notice This telecom equipment has complied with NTC regulations. Taiwan NCC notices Wireless LAN 802.11a devices Singapore wireless notice 7 Wireless LAN 802.11 devices/Bluetooth devices/Short range devices Airline travel notice Use of electronic equipment onboard commercial aircraft is at the discretion of the airline. User-replaceable battery notices When a battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for computer battery disposal. HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, refer to the HP Web site at http://www.hp.com/

recycle. For information about removing a user-replaceable battery, refer to the user guide included with the product. Factory-sealed battery notices The battery[ies] in this product cannot be easily replaced by users themselves. Removing or replacing the battery could affect your warranty coverage. If a battery is no longer holding a charge, contact support. When a battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for battery disposal. 8 Chapter 1 Regulatory notices for notebook computers Laser compliance WARNING! Use of controls or adjustments, or performance of procedures other than those specified in the laser product installation guide, may result in hazardous radiation exposure. To reduce the risk of exposure to hazardous radiation:

Do not try to open the module enclosure. There are no user-serviceable components inside. Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified in the laser product installation guide. Allow only authorized service providers to repair the unit. This product may be provided with an optical storage device (for example, a CD or DVD drive) and/or a fiber optic transceiver. Each of these devices that contain a laser is classified as a Class 1 Laser Product in accordance with IEC/EN 60825-1 and meets the requirements for safety of that standard. Each laser product complies with US FDA regulations of 21 CFR 1040.10 and 1040.11 or complies with those regulations except for deviations pursuant to Laser Notice No. 50 dated June 24, 2007. Modem notices WARNING! To reduce the risk of fire, electric shock, and injury to persons when using this device, always follow basic safety precautions, including the following:

Do not use this product near waterfor example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Avoid using this product during an electrical storm. There is a remote risk of electric shock from lightning. Do not use this product to report a gas leak while in the vicinity of the leak. Always disconnect the modem cable before opening the equipment enclosure or touching an uninsulated modem cable, jack, or internal component. If this product was not provided with a telephone line cord, use only No. 26 AWG or larger telecommunication line cord. Do not plug a modem or telephone cable into the RJ-45 (network) jack. SAVE THESE INSTRUCTIONS. Telecommunications device approvals The telecommunications device in the computer is approved for connection to the telephone network in the countries and regions whose approval markings are indicated on the product label located on the bottom of the computer or on the modem. Refer to the user guide included with the product to ensure that the product is configured for the country or region in which the product is located. Selecting a country or region other than the one in which it is located may cause the modem to be configured in a way that violates the telecommunication regulations/laws of Laser compliance 9 that country or region. In addition, the modem may not function properly if the correct country or region selection is not made. If, when you select a country or region, a message appears that states that the country or region is not supported, this means that the modem has not been approved for use in this country or region and thus should not be used. U.S. modem statements This equipment complies with Part 68 of the FCC Rules and the requirements adopted by the ACTA. On the bottom of the computer or on the modem is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. Provide this information to the telephone company if you are requested to do so. Applicable certification jack USOC = RJ11C. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all locations, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. If this HP equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But, if advance notice isn't practical, the telephone company will notify you as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes to its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted telephone service. If trouble is experienced with this equipment, call technical support. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. You should perform repairs only to the equipment specifically discussed in the Troubleshooting section of the user guide, if one is provided. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission, or corporation commission for information. If your home has specially wired alarm equipment connected to the telephone line, ensure that the installation of this HP equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including a fax machine, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page, or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity, or other individual sending the message, and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-

distance transmission charges). In order to program this information into your fax machine, you should complete the steps outlined in the faxing software instructions. 10 Chapter 1 Regulatory notices for notebook computers U.S. modem declarations Refer to the following modem vendor declarations for the modem device installed in your computer:

Modem notices 11 Canada modem statements This equipment meets the applicable Industry Canada technical specifications. The Ringer Equivalence Number, REN, is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices, subject only to the requirement that the sum of the RENs of all devices does not exceed 5. The REN for this terminal equipment is 1.0. Japan modem statements If the computer does not have the Japanese certification mark on the bottom of the computer, refer to the appropriate certification marking below. The Japanese certification mark for the V.92 56K Data/Fax Modem is below:

New Zealand modem statements The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services. This equipment is not capable, under all operating conditions, of correct operation at the higher speeds for which it is designed. Telecom will accept no responsibility should difficulties arise in such circumstances. If this device is equipped with pulse dialing, note that there is no guarantee that Telecom lines will always continue to support pulse dialing. Use of pulse dialing, when this equipment is connected to the same line as other equipment, may give rise to bell tinkle or noise and may also cause a false answer condition. Should such problems occur, the user should not contact the Telecom Faults Service. Some parameters required for compliance with Telecom's Telepermit requirements are dependent on the equipment (PC) associated with this device. The associated equipment shall be set to operate within the following limits for compliance with Telecom's Specifications:

a. b. There shall be no more than 10 call attempts to the same number within any 30-minute period for any single manual call initiation. The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next attempt. c. Where automatic calls are made to different numbers, the equipment shall be set to go on-hook for a period of not less than 5 seconds between the end of one attempt and the beginning of the next attempt. d. The equipment shall be set to ensure that calls are answered between 3 and 30 seconds of receipt of ringing (So set between 2 and 10). 12 Chapter 1 Regulatory notices for notebook computers Voice support All persons using this device for recording telephone conversations shall comply with New Zealand law. This requires that at least one party to the conversation is aware that it is being recorded. In addition, the Principles enumerated in the Privacy Act 1993 shall be complied with in respect to the nature of the personal information collected, the purpose for its collection, how it is to be used, and what is disclosed to any other party. This equipment shall not be set to make automatic calls to the Telecom 111' Emergency Service. Power cord notice If you were not provided with a power cord for the computer or for an external power accessory intended for use with the computer, you should purchase a power cord that is approved for use in your country or region. The power cord must be rated for the product and for the voltage and current marked on the product's electrical ratings label. The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product. In addition, the diameter of the wire must be a minimum of 0.75 mm/

18AWG, and the length of the cord must be between 1.0 m (3.2 ft) and 2 m (6.56 ft). If you have questions about the type of power cord to use, contact your authorized service provider. A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it. Particular attention should be paid to the plug, electrical outlet, and the point where the cord exits from the product. Japan power cord notice DC plug of external HP power supply Macrovision Corporation notice This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. Power cord notice 13 2 Regulatory notices for desktops, thin clients and personal workstations Modem notices WARNING! To reduce the risk of fire, electric shock, and injury to persons when using this device, always follow basic safety precautions, including the following:

Do not use this product near waterfor example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Avoid using this product during an electrical storm. There is a remote risk of electric shock from lightning. Do not use this product to report a gas leak while in the vicinity of the leak. Always disconnect the modem cable before opening the equipment enclosure or touching an uninsulated modem cable, jack, or internal component. If this product was not provided with a telephone line cord, use only No. 26 AWG or larger telecommunication line cord. Do not plug a modem or telephone cable into the RJ-45 (Ethernet network) jack. SAVE THESE INSTRUCTIONS. Telecommunications device approvals The telecommunications device in the computer is approved for connection to the telephone network in the countries and regions whose approval markings are indicated on the product label located on the bottom of the computer or on the modem. Refer to the user guide included with the product to ensure that the product is configured for the country or region in which the product is located. Selecting a country or region other than the one in which it is located may cause the modem to be configured in a way that violates the telecommunication regulations/laws of that country or region. In addition, the modem may not function properly if the correct country or region selection is not made. If, when you select a country or region, a message appears that states that the country or region is not supported, this means that the modem has not been approved for use in this country or region and thus should not be used. U.S. modem statements This equipment complies with Part 68 of the FCC Rules and the requirements adopted by the ACTA. On the bottom of the computer or on the modem is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. Provide this information to the telephone company if you are requested to do so. Applicable certification jack USOC = RJ11C. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. 14 Chapter 2 Regulatory notices for desktops, thin clients and personal workstations The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all locations, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. If this HP equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But, if advance notice isn't practical, the telephone company will notify you as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes to its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted telephone service. If trouble is experienced with this equipment, call technical support. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. You should perform repairs only to the equipment specifically discussed in the Troubleshooting section of the user guide, if one is provided. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission, or corporation commission for information. If your home has specially wired alarm equipment connected to the telephone line, ensure that the installation of this HP equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including a fax machine, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page, or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity, or other individual sending the message, and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-

distance transmission charges). In order to program this information into your fax machine, you should complete the steps outlined in the faxing software instructions. Canadian modem statements This equipment meets the applicable Industry Canada technical specifications. The Ringer Equivalence Number, REN, is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices, subject only to the requirement that the sum of the RENs of all devices does not exceed 5. The REN for this terminal equipment is 1.0. Japanese modem statements If the computer does not have the Japanese certification mark on the bottom of the computer, refer to the appropriate certification marking below. The Japanese certification mark for the LSI Corporation PCI-SV92EX Soft modem is below:

Modem notices 15 New Zealand modem statements The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services. This equipment is not capable, under all operating conditions, of correct operation at the higher speeds for which it is designed. Telecom will accept no responsibility should difficulties arise in such circumstances. If this device is equipped with pulse dialing, note that there is no guarantee that Telecom lines will always continue to support pulse dialing. Use of pulse dialing, when this equipment is connected to the same line as other equipment, may give rise to bell tinkle or noise and may also cause a false answer condition. Should such problems occur, the user should not contact the Telecom Faults Service. Some parameters required for compliance with Telecom's Telepermit requirements are dependent on the equipment (PC) associated with this device. The associated equipment shall be set to operate within the following limits for compliance with Telecom's Specifications:

a. b. There shall be no more than 10 call attempts to the same number within any 30-minute period for any single manual call initiation. The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next attempt. c. Where automatic calls are made to different numbers, the equipment shall be set to go on-hook for a period of not less than 5 seconds between the end of one attempt and the beginning of the next attempt. d. The equipment shall be set to ensure that calls are answered between 3 and 30 seconds of receipt of ringing (So set between 2 and 10). Voice support All persons using this device for recording telephone conversations shall comply with New Zealand law. This requires that at least one party to the conversation is aware that it is being recorded. In addition, the Principles enumerated in the Privacy Act 1993 shall be complied with in respect to the nature of the personal information collected, the purpose for its collection, how it is to be used, and what is disclosed to any other party. This equipment shall not be set to make automatic calls to the Telecom 111' Emergency Service. Electromagnetic compatibility notices This guide provides country- and region-specific nonwireless and wireless regulatory notices and compliance information for the computer product. Some of these notices may not apply to your product. One or more integrated wireless devices may be installed. In some environments, the use of wireless devices may be restricted. Such restrictions may apply onboard airplanes, in hospitals, near explosives, in hazardous 16 Chapter 2 Regulatory notices for desktops, thin clients and personal workstations locations, and so on. If you are uncertain of the policy that applies to the use of this product, ask for authorization to use it before you turn it on. Federal Communications Commission notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio or television technician for help. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user's authority to operate the equipment. Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations. Declaration of conformity for products marked with the FCC logo (United States only) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. 2. This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. For questions regarding the product, contact:

Hewlett-Packard Company P.O. Box 692000, Mail Stop 530113 Houston, Texas 77269-2000 For questions regarding this FCC declaration, contact:

Hewlett-Packard Company P.O. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000 Or, call (281) 514-3333. To identify this product, refer to the part, series, or model number found on the product. Products with wireless LAN devices This product may be equipped with a wireless LAN device. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Electromagnetic compatibility notices 17 WARNING! Exposure to Radio Frequency Radiation The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact is minimized during normal operation. During normal operation: To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antennae should not be less than 20 cm (8 inches). To identify the location of the wireless antennae, refer to the documentation included with the computer. CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15- to 5.25-GHz frequency range. The FCC requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to cochannel mobile satellite systems. High-power radar is allocated as the primary user of the 5.25- to 5.35-GHz and 5.65- to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device. Australia telecom statement The computer must be connected to the Telecommunication Network through a line cord that meets the requirements of AS/CA S008. WARNING! Modems without integral RJ11 connector that are shipped with this computer should not be installed in any other device. This equipment incorporates a radio transmitting and receiving device. In normal use, a separation distance of 20 cm ensures that radio frequency exposure levels comply with the Australian and New Zealand Standards. 18 Chapter 2 Regulatory notices for desktops, thin clients and personal workstations Brazil notice Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio. CAUTION: A alimentao de energia predefinida para 220/230Vv. Se voc possuir tomada eltrica de 110/115Vv, por favor, altere a chave na parte traseira do seu computador para a tenso correta. Canadian notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations, CAN ICES-3(B)/NMB-3(B). If this device has WLAN or Bluetooth capability, this device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. WARNING! Exposure to Radio Frequency Radiation The radiated output power of this device is below the Industry Canada radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact is minimized during normal operation. During normal operation: To avoid the possibility of exceeding the Industry Canada radio frequency exposure limits, human proximity to the antennae should not be less than 20 cm (8 inches). To identify the location of the wireless antennae, refer to the documentation included with the computer. CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15- to 5.25-GHz frequency range. Industry Canada requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-

channel mobile satellite systems. High-power radar is allocated as the primary user of the 5.25- to 5.35-GHz and 5.65- to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device. The antenna for this device is not replaceable. Any attempt at user modification may damage your computer. European Union regulatory notices Declaration of Conformity Products bearing the CE marking comply with one or more of the following EU Directives as may be applicable:

Low Voltage Directive 2006/95/EC; EMC Directive 2004/108/EC; Ecodesign Directive 2009/125/EC; R&TTE Directive 1999/5/EC; RoHS Directive 2011/65/EU Compliance with these directives is assessed using applicable European Harmonised Standards. The full Declaration of Conformity can be found at the following web site: www.hp.eu/certificates (Search with the product model name or its Regulatory Model Number (RMN), which may be found on the regulatory label.) The point of contact for regulatory matters is Hewlett-Packard GmbH, Dept./MS:HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, GERMANY. Products with wireless functionality (EMF) This product meets international guidelines (ICNIRP) for exposure to radio frequency radiation. Electromagnetic compatibility notices 19 This product may incorporate a radio transmitting and receiving device. For desktop computers in normal use, a separation distance of 20 cm ensures that radio frequency exposure levels comply with EU requirements. Restrictions for product with wireless functionality This product is designed for use without restrictions in all EU countries, plus Iceland, Liechtenstein, Norway, and Switzerland. European telephone network declaration (Modem/Fax) The product herewith complies with the requirements of the R&TTE Directive 1999/5/EC (Annex II) and carries the CE marking accordingly. However, due to differences between the individual PSTNs provided in different countries/regions, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems, you should contact your equipment supplier in the first instance. This equipment has been designed to work with analogue DTMF Networks. This equipment may have internetworking difficulties in PSTN networks that only support Pulse Dialing. Please consult with your network operator for further assistance. Ergonomics notice Germany (English text) A computer system comprising HP brand products meets the applicable German ergonomic requirements if all affected constituent products bear the "GS" approval mark, for example Business Desktop PC, keyboard, PC-mouse and monitor. Germany (Deutscher text) Ein aus HP Produkten bestehendes Computersystem erfllt die anwendbaren ergonomischen Anforderungen, wenn alle verwendeten Komponenten das GS Zeichen tragen, wie z. B. Business Desktop PC, Tastatur, PC-Maus und Bildschirm. Japan notice B VCCI-B Wireless LAN and Bluetooth certification markings If this device contains radio equipment, it is certified radio equipment. South Korea notices B ( ) 20 Chapter 2 Regulatory notices for desktops, thin clients and personal workstations

(B) ,

.

(

). 20cm . This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and personnel. Mexico notice Declaracin para Mxico La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. If your product is provided with wireless accessories such as a keyboard or mouse and you need to identify the model of the accessory, refer to the label included on that accessory. Taiwan NCC notices Wireless LAN 802.11a devices Electromagnetic compatibility notices 21 Wireless LAN 802.11 devices/Bluetooth devices/Short range devices 22 Chapter 2 Regulatory notices for desktops, thin clients and personal workstations 3 Safety notices for notebook computers WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper workstation setup, posture, and health and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located on the Web at http://www.hp.com/ergo and on the Documentation CD that is included with the product. Heat-related safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the AC adapter comply with the user-accessible surface temperature limits defined by the International Standard for Safety of Information Technology Equipment (IEC/EN 60950). Potential safety conditions notice If you notice any of the following conditions (or if you have other safety concerns), do not use the computer:

crackling, hissing, or popping sound, or a strong odor or smoke coming from the computer. It is normal for these conditions to appear when an internal electronic component fails in a safe and controlled manner. However, these conditions may also indicate a potential safety issue. Do not assume it is a safe failure. Turn off the computer, disconnect it from its power source, and contact technical support for assistance. User-replaceable battery notices WARNING! Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. WARNING! To reduce the risk of fire or burns, do not disassemble, crush, or puncture; do not short external contacts; do not dispose of in fire or water. WARNING! Keep the battery away from children. WARNING! To reduce potential safety issues, only the battery provided with the computer, a replacement battery provided by HP, or a compatible battery purchased as an accessory from HP should be used with the computer. Heat-related safety warning notice 23 Headset and earphone volume level notice WARNING!

Listening to music at high volume levels and for extended durations can damage ones hearing. To reduce the risk of hearing damage, lower the volume to a safe, comfortable level and reduce the amount of time listening at high levels. For your own safety, before using headsets or earphones, always reset the volume. Some headphones are louder than other headphones, even if the volume control setting is the same. Changing the default audio or equalizer settings might lead to higher volume and should only be done with caution. For your own safety, headsets or earphones used with this product should comply with the headphone limits in EN 50332-2. If the computer includes a headset or earphones, this combination is in compliance to EN 50332-1. Power cord notices WARNING! To reduce the risk of electric shock or damage to the equipment:

Plug the power cord into an AC outlet that is easily accessible at all times. Disconnect power from the computer by unplugging the power cord from the AC outlet. If provided with a 3-pin attachment plug on the power cord, plug the cord into a grounded (earthed) 3-

pin outlet. Do not disable the power cord grounding pin, for example, by attaching a 2-pin adapter. The grounding pin is an important safety feature. WARNING! To reduce potential safety issues, only the AC adapter provided with the computer, a replacement AC adapter provided by HP, or an AC adapter purchased as an accessory from HP should be used with the computer. Brazil notice Este equipamento deve ser conectado obrigatoriamente em tomada de rede de energia eltrica que possua aterramento (trs pinos), conforme a norma nbr abnt 5410,visando a segurana dos usurios contra choques eltricos. Cleaning the keyboard WARNING! To reduce the risk of electric shock or damage to internal components, do not use a vacuum cleaner attachment to clean the keyboard. A vacuum cleaner can deposit household debris on the keyboard surface. Clean the keyboard regularly to prevent keys from sticking and to remove dust, lint, and particles that can become trapped beneath the keys. A can of compressed air with a straw extension can be used to blow air around and under the keys to loosen and remove debris. Travel notice WARNING! To reduce the risk of electric shock, fire, or damage to the equipment, do not attempt to power the computer with a voltage converter kit sold for appliances. 24 Chapter 3 Safety notices for notebook computers China safety notices China: Altitude notice Altitude warning for products not certified for use in >5000 m 2000m or 2000 China: Tropical warning notice Tropical warning for products not certified for use in tropical regions. Norway and Sweden: Cable grounding notice for products with a TV tuner CAUTION: To reduce potential safety issues, use a galvanic isolator when connecting to a cable distribution system. Taiwan BSMI notice BSMI 1. 30 10 2. 2 2 1 China safety notices 25 4 Safety notices for desktops, thin clients and personal workstations Important safety information WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper workstation setup, posture, and health and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located on the Web at http://www.hp.com/ergo and on the Documentation CD that is included with the product. To reduce the risk of electric shock or damage to the equipment:

Plug the power cord into an AC outlet that is easily accessible at all times. Disconnect power from the computer by unplugging the power cord from the AC outlet. If provided with a 3-pin attachment plug on the power cord, plug the cord into a grounded (earthed) 3-

pin outlet. Do not disable the power cord grounding pin, for example, by attaching a 2-pin adapter. The grounding pin is an important safety feature. The computer may be heavy; be sure to use ergonomically correct lifting procedures when moving it. Install the computer near an AC outlet. The AC power cord is your computers main AC disconnecting device and must be easily accessible at all times. For your safety, the power cord provided with your computer has a grounded plug. Always use the power cord with a properly grounded wall outlet, to avoid the risk of electrical shock. To reduce the possibility of an electric shock from the telephone network, plug your computer into the AC outlet before connecting it to the telephone line. Also, disconnect the telephone line before unplugging your computer from the AC power outlet. Always disconnect the modem cord from the telephone system before installing or removing your computer cover. Do not operate the computer with the cover removed. For your safety, always unplug the computer from its power source and from any telecommunications systems (such as telephone lines), networks, or modems before performing any service procedures. Failure to do so may result in personal injury or equipment damage. Hazardous voltage levels are inside the power supply and modem of this product. If your computer is provided with a voltage select switch for use in a 115 or 230 V power system, CAUTION:

the voltage select switch has been pre-set to the correct voltage setting for use in the particular country/

region where it was initially sold. Changing the voltage select switch to the incorrect position can damage your computer and void any implied warranty. This product has not been evaluated for connection to an IT power system (an AC distribution system with no direct connection to earth, according to IEC/EN 60950). Installation conditions See installation instructions before connecting this equipment to the input supply. 26 Chapter 4 Safety notices for desktops, thin clients and personal workstations WARNING! The equipment must be provided with a proper AC protective earth (PE) ground connection. Energized and moving parts may be inside the computer. Disconnect power to the equipment before removing the enclosure. Replace and secure the enclosure before re-energizing the equipment. Battery replacement notice WARNING! The product may contain an internal lithium manganese dioxide, vanadium pentoxide, or alkaline battery or battery pack. There is risk of fire and burns if the battery pack is not handled properly. To reduce the risk of personal injury:

Do not attempt to recharge the battery. Do not expose to temperatures higher than 60 C (140 F). Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Replace only with the HP spare designated for this product. For information about removing a battery, refer to your computer documentation. Batteries, battery packs, and accumulators should not be disposed of together with the general household waste. In order to forward them to recycling or proper disposal, please use the public collection system or return them to HP, an authorized HP partner, or their agents. The Taiwan EPA requires dry battery manufacturing or importing firms, in accordance with Article 15 of the Waste Disposal Act, to indicate the recovery marks on the batteries used in sales, giveaways, or promotions. Contact a qualified Taiwanese recycler for proper battery disposal. Headset and earphone volume level notice WARNING!

Listening to music at high volume levels and for extended durations can damage ones hearing. To reduce the risk of hearing damage, lower the volume to a safe, comfortable level and reduce the amount of time listening at high levels. For your own safety, before using headsets or earphones, always reset the volume. Some headphones are louder than other headphones, even if the volume control setting is the same. Changing the default audio or equalizer settings might lead to higher volume and should only be done with caution. If the computer includes a headset or earphones and bears the "GS" mark, this combination is in compliance with EN 50332-1. For your own safety, headsets or earphones used with these products should comply with the headphone limits in EN 50332-2. Battery replacement notice 27 Laser safety For products equipped with optical drives or fiber optic transceivers. This product may be provided with an optical storage device (i.e., CD or DVD drive) and/or fiber optic transceiver. These contain lasers and are classified as Class 1 Laser Products in accordance with the standard IEC/EN 60825-1 and comply with its requirements. Each laser product complies with US FDA Regulations of 21 CFR 1040.10 and 1040.11 or complies with those regulations except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. WARNING! Use of controls or adjustments or performance of procedures other than those specified herein or in the laser products installation guide may result in hazardous radiation exposure. To reduce the risk of exposure to hazardous radiation:

Do not try to open the module enclosure. There are no user-serviceable components inside. Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein. Allow only HP Authorized Service technicians to repair the unit. Power supply and power cord set requirements Power supply class I grounding requirements For protection from fault currents, the equipment shall be connected to a grounding terminal. Plug the system power cord into an AC outlet that provides a ground connection. Substitute cords may not provide adequate fault protection. Only use the power cord supplied with this product or a Hewlett-Packard authorized replacement. Brazil notice Este equipamento deve ser conectado obrigatoriamente em tomada de rede de energia eltrica que possua aterramento (trs pinos), conforme a norma nbr abnt 5410,visando a segurana dos usurios contra choques eltricos. Denmark Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver forbindelse til stikproppens jord. Finland Norway Sweden Laite on liitettv suojakoskettimilla varustettuun pistorasiaan. Apparatet m tilkoples jordet stikkontakt. Apparaten skall anslutas till jordat uttag. Power supply requirements The power supplies on some products have external power switches. The voltage select switch feature on the product permits it to operate from any line voltage between 100-127 or 200-240 volts AC. Power supplies on 28 Chapter 4 Safety notices for desktops, thin clients and personal workstations those products that do not have external power switches are equipped with internal circuits that sense the incoming voltage and automatically switch to the proper voltage. For safety reasons, use only the AC adapter provided with the unit or an authorized replacement adapter from Hewlett-Packard. Replacement part numbers may be found at http://www.hp.com/cgi-bin/hpsupport/

index.pl. For use in Norway This product is also designed for an IT power system with phase-to-phase voltage 230V. Power cord set requirements The power cord set received with the product meets the requirements for use in the country where the equipment was originally purchased. Use only the power cord provided with the unit or an authorized replacement power cord from Hewlett-Packard or an approved HP source. Replacement part numbers may be found at http://www.hp.com/cgi-bin/hpsupport/index.pl. Power cord sets for use in other countries must meet the requirements of the country where you use the product. For more information on power cord set requirements, contact your authorized HP dealer, reseller, or service provider. WARNING! Do not use power cords from other products. Mismatched power cords may result in a shock and fire hazard. The requirements listed below are applicable to all countries:

1. 2. The power cord must be approved by an acceptable accredited agency responsible for evaluation in the country where the power cord set will be installed. The length of the power cord must be between 1.8 m (6 feet) and 3.6 m (12 feet). For a power cord 2.0 m (6.56 feet) or less, the diameter of the wire must be a minimum of 0.75 mm2 or 18AWG. If the power cord is longer than 2.0 m (6.56 feet), the diameter of the wire must be a minimum of 1.0 mm2 or 16AWG. The power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it. Particular attention should be paid to the plug, electrical outlet, and the point where the cord exits from the product. WARNING! Do not operate this product with a damaged power cord set. If the power cord set is damaged in any manner, replace it immediately. Damaged cords may result in user exposure to hazards. Japan power cord requirements For use in Japan, use only the power cord received with this product. CAUTION: Do not use the power cord received with this product on any other products. Pinch hazard WARNING! Observe pinch hazard areas. Keep fingers away from closing parts. Pinch hazard 29 TV antenna connectors protection External television antenna grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is electrically grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper electrical grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-

discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. Lightning protection For added protection of any product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug the product from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product from lightning and power line surges. Table 4-1 Antenna Grounding Reference Grounding Component 1 2 3 4 5 6 7 Electric Service Equipment Power Service Grounding Electrode System (NEC Art 250, Part III) Ground Clamps Grounding Conductors (NEC Section 810.21) Antenna Discharge Unit (NEC Section 810.20) Ground Clamp Antenna Lead-in Wire Note to CATV system installer This reminder is provided to call the CATV systems installers attention to section 820.93 of the National Electric Code, which provides guidelines for proper grounding and in particular, specify that the Coaxial cable 30 Chapter 4 Safety notices for desktops, thin clients and personal workstations shield shall be connected to grounding system of the building, as close to the point of cable entry as practical. China safety notices China: Altitude notice Altitude warning for products not certified for use in >5000 m 2000m or 2000 China: Tropical warning notice Tropical warning for products not certified for use in tropical regions. China safety notices 31 Germany acoustics notice Sound pressure level (LpA) is far below 70dB(A) (operator position, normal operation, according to ISO 7779) Product noise emission data can be found in the product related IT ECO Declarations at Internet address:

http://www.hp.com/go/ted Schalldruckpegel (LpA) ist weit unterhalb 70 dB(A) (Benutzerposition, normaler Betrieb, nach ISO 7779) Die Schallemissionswerte der Produkte knnen in den produktbezogenen IT ECO Declarations auf folgender Internet Adresse gefunden werden: http://www.hp.com/go/ted Taiwan BSMI notice BSMI 1. 30 10 2. 2 2 1 32 Chapter 4 Safety notices for desktops, thin clients and personal workstations 5 Environmental notices for notebook computers This chapter provides country- and region-specific environmental notices and compliance information. Some of these notices may not apply to your product. Electronic hardware, packaging and battery recycling HP encourages customers to recycle used electronic hardware, HP original print cartridges packaging, and rechargeable batteries. For more information about recycling programs, go to http://www.hp.com/recycle. For information about recycling the product in Japan, refer to http://www.hp.com/jp/hardwarerecycle/. Disposal of waste equipment by users This symbol means do not dispose of your product with your other household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment. For more information, please contact your household waste disposal service or go to http://www.hp.com/recycle. Brazil alkaline battery disposal HEWLETT PACKARD BRASIL LTDA (HP) AV. JOS LUIZ MAZALI N 360 - GALPO B-PARTE 1-BAIRRO RESIDENCIAL BURCK - LOUVEIRA/SP - CEP: 13290-000 CNPJ: 61.797.924/0007-40 Centro de Informaes HP: (11) 4004-7751 ou 0800-7097751 No descarte o produto eletrnico em lixo comum Este produto eletroeletrnico e seus componentes no devem ser descartados no lixo comum, pois embora estejam em conformidade com padres mundiais de restrio a substncias nocivas, podem conter, ainda que em quantidades mnimas, substncias impactantes ao meio ambiente. Ao final da vida til deste produto, o usurio dever entreg-lo HP. A no observncia dessa orientao sujeitar o infrator s sanes previstas em lei. Aps o uso, as pilhas e/ou baterias dos produtos HP devero ser entregues ao estabelecimento comercial ou rede de assistncia tcnica autorizada pela HP. Para maiores informaes , inclusive sobre os pontos de recebimento, acesse: http://www.hp.com.br/reciclar Electronic hardware, packaging and battery recycling 33 Brazil hardware recycling information HEWLETT PACKARD BRASIL LTDA (HP) AV. JOS LUIZ MAZALI N 360 - GALPO B-PARTE 1-BAIRRO RESIDENCIAL BURCK - LOUVEIRA/SP - CEP: 13290-000 CNPJ: 61.797.924/0007-40 Centro de Informaes HP: (11) 4004-7751 ou 0800-7097751 No descarte o produto eletrnico em lixo comum Este produto eletroeletrnico e seus componentes no devem ser descartados no lixo comum, pois embora estejam em conformidade com padres mundiais de restrio a substncias nocivas, podem conter, ainda que em quantidades mnimas, substncias impactantes ao meio ambiente. Ao final da vida til deste produto, o usurio dever entreg-lo HP. A no observncia dessa orientao sujeitar o infrator s sanes previstas em lei. Aps o uso, as pilhas e/ou baterias dos produtos HP devero ser entregues ao estabelecimento comercial ou rede de assistncia tcnica autorizada pela HP. Para maiores informaes , inclusive sobre os pontos de recebimento, acesse: http://www.hp.com.br/reciclar ENERGY STAR Certification (select models only) ENERGY STAR is a U.S. Environmental Protection Agency voluntary program that helps businesses and individuals save money and protect our climate through superior energy efficiency. Products that earn the ENERGY STAR prevent greenhouse gas emissions by meeting strict energy efficiency criteria or requirements set by the U.S. Environmental Protection Agency. As an ENERGY STAR Partner, Hewlett-Packard Company has followed the U.S. EPAs enhanced product certification process to ensure that products marked with the ENERGY STAR logo are ENERGY STAR certified per the applicable ENERGY STAR guidelines. The following logo appears on all ENERGY STAR-certified computers::

A key ENERGY STAR requirement for computer products is power management features that significantly reduce energy consumption when the product is not in use. Power management allows a computer to automatically enter a low power sleep mode, or other low power mode, after a defined period of inactivity. The power management features have been preset as follows when the computer is operating on AC power:

Computer type Time to activate display sleep mode Time to activate computer sleep mode (minutes) Resuming from sleep mode Notebooks, Mobile Workstations Less than or equal to 15 minutes (varies by model) Less than or equal to 30 minutes (varies by model) Product will exit sleep mode when the power/sleep button is pressed. If Wake-on-Lan (WOL) is enabled, the system can resume from sleep in response to a network signal. Tablets/Slates Less than or equal to 1 minute Not applicable Not applicable For computers that support an always-on, always-connected use profile where internet access is available

(such as tablets and slates), alternative low power modes - such as Short or Long Idle modes (as defined in the ENERGY STAR Computer Program Requirements) are provided that consume very little power (</= 10 34 Chapter 5 Environmental notices for notebook computers Watts) and when applicable, maximize product battery life. These alternative low power modes are dynamic, with the display sleep mode activated within 1 minute of user inactivity. The computer exits Sleep when the power/Sleep button is pressed. When the Wake On LAN (WOL) feature is enabled, the computer can also exit Sleep in response to a network signal. Additional information on the potential energy and financial savings of the power management feature can be found on the EPA ENERGY STAR Power Management Web site at http://www.energystar.gov/

powermanagement. Additional information on the ENERGY STAR program and its environmental benefits are available on the EPA ENERGY STAR Web site at http://www.energystar.gov. ENERGY STAR and the ENERGY STAR mark are registered trademarks owned by the U.S. Environmental Protection Agency. Chemical substances HP is committed to providing our customers with information about the chemical substances in our products as needed to comply with legal requirements such as REACH (Regulation EC No 1907/2006 of the European Parliament and the Council). A chemical information report for this product can be found at http://www.hp.com/go/reach. China environmental notices http://www.hp.com/hpinfo/globalcitizenship/environment/productdata/chinasepa.html http://www.hp.com.cn/hardwarerecycle

:

(, ) ,,,

,,,, (http://

www.sepa.gov.cn), 3

:

China PC energy label In accordance with The Regulation of the Implementation on China Energy Label for Microcomputers

(CEL-30), this microcomputer has an Energy Efficiency Label. The energy efficiency grade, TEC (Typical Energy Consumption), and product category presented on the label are determined and calculated according to the standard GB28380-2012. Chemical substances 35 1. Energy Efficiency Grades The grade is determined by the standard with the calculation of base consumption level with the sum of all the allowances for additional components such as main memory and graphics card. For products of any grade, the TEC should not exceed the value specified in the following table:

Product Type Grade 1 Grade 2 Grade 3 TEC (kilowatt hour) Desktop microcomputer, AIO Category A 98.0+Efa 148.0+Efa 198.0+Efa Portable Computer Category B Category C Category D Category A Category B Category C 125.0+Efa 159.0+Efa 184.0+Efa 20.0+Efa 26.0+Efa 54.5+Efa 175.0+Efa 225.0+Efa 209.0+Efa 259.0+Efa 234.0+Efa 284.0+Efa 35.0+Efa 45.0+Efa 75.0+Efa 45.0+Efa 65.0+Efa 123.5+Efa NOTE: Efa is the sum of power factor of product additional functions. 2. Typical Energy Consumption The energy consumption figure presented on the label is the data measured with the representative configuration that covers all the configurations in the registration unit which is selected according to CEL-30. Thus, actual energy consumption of this specific microcomputer may not be the same as the TEC data presented in the label. 3. Product Category The product category is determined by the standard according to the microcomputers configuration. The categorization of products complies with the regulations in the following table:

Product Type Category A Category B Category C Configuration Description Desktop microcomputer, AIO Portable Computer The desktop microcomputer and AIO whose configuration is out of the scope of Category B, C, and D The portable computer whose configuration is out of the scope of Category B and C CPU physical core number of 2, and system memory of not less than 2GB A Discrete GPU CPU physical core number of over 2, with at least one of the following features:

1. 2. System memory of not less than 2 GB A Discrete GPU The product that has a CPU physical core number of not less than 2, system memory of not less than 2GB, A Discrete GPU with Frame Buffer Width not less than 128-bit. Category D CPU physical core number of not less than 4, with at least one of the following features:

1. 2. System memory of not less than 4 GB A Discrete GPU with Frame Buffer Width not less than 128-bit 36 Chapter 5 Environmental notices for notebook computers For more details on the specification, please refer to the standard GB28380-2012. CEL30 GB28380 2012:

1.

() A B C D A B C 1 2 3 98.0+Efa 148.0+Efa 198.0+Efa 125.0+Efa 175.0+Efa 225.0+Efa 159.0+Efa 209.0+Efa 259.0+Efa 184.0+Efa 234.0+Efa 284.0+Efa 20.0+Efa 35.0+Efa 45.0+Efa 26.0+Efa 45.0+Efa 65.0+Efa 54.5+Efa 75.0+Efa 123.5+Efa Efa 2. 3. A B C D B C D CPU 2 2GB CPU 2 a. a 2GB b. GPU) B C GPU CPU 2 2GB GPU 128

. CPU 4 a. 4GB b. GPU 128 China PC energy label 37 GB28380-2012 China restriction of hazardous substances (RoHS) The Table of Hazardous Substances/Elements and their Content As required by China's Management Methods for Controlling Pollution by Electronic Information Products Hazardous Substances and Elements Part Name Lead (Pb) Mercury

(Hg) Cadmium

(Cd) Hexavalent Chromium

(Cr(VI)) Polybrominated biphenyls (PBB) Polybrominated diphenyl ethers

(PBDE) Battery Cables Camera Chassis/Other Flash memory card reader Floppy disk drive Hard disk drive Headphones I/O PCAs Keyboard Liquid crystal display

(LCD) panel Media (CD/DVD/floppy) Memory Motherboard, processor, heat sinks Mouse Optical disk drive Optional docking device Power adapter Power supply Remote control Smart card/Java card reader Speakers, external TV tuner X X X X X X X X X X X O X X X X X X X X X X X O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O 38 Chapter 5 Environmental notices for notebook computers Hazardous Substances and Elements Part Name Lead (Pb) USB flash memory drive USB hub Web camera Wireless receiver Wireless cards X X X X X Mercury

(Hg) Cadmium

(Cd) Hexavalent Chromium

(Cr(VI)) Polybrominated biphenyls (PBB) Polybrominated diphenyl ethers

(PBDE) O O O O O O O O O O O O O O O O O O O O O O O O O This form has been prepared in compliance with the provisions of SJ/T 11364. O: Indicates that the content of said hazardous substance in all of the homogenous materials in the component is within the limits required by GB/T 26572. X: Indicates that the content of said hazardous substance exceeds the limits required by GB/T 26572 in at least one homogenous material in the component. All parts named in this table with an X are in compliance with the European Unions RoHS Legislation. NOTE: The referenced Environmental Protection Use Period Marking was determined according to normal operating use conditions of the product such as temperature and humidity.

/

I/O PCA

(LCD) CD/DVD/

(Pb)

(Hg)

(Cd)

(Cr(VI)) (PBB)

(PBDE) X X X X X X X X X X X O X X O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O China restriction of hazardous substances (RoHS) 39

/Java USB USB

(Pb)

(Hg)

(Cd)

(Cr(VI)) (PBB)

(PBDE) X X X X X X X X X X X X X X O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O SJ/T 11364 O: GB/T 26572 X GB/T 26572 X RoHS

:

40 Chapter 5 Environmental notices for notebook computers India restriction of hazardous substances (RoHS) This product complies with the India E-waste (Management and Handling) Rule 2011 and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule. Japan restriction of hazardous substances (RoHS) 2008 JISC0950 2006 7 http://www.hp.com/go/jisc0950 A Japanese regulatory requirement, defined by specification JIS C 0950, 2008, mandates that manufacturers provide Material Content Declarations for certain categories of electronic products offered for sale after July 1, 2006. To view the JIS C 0950 material declaration for this product, visit http://www.hp.com/go/jisc0950. Mexico Sustainable Energy Use Law This product has been labeled in compliance with the Mexico Sustainable Energy Use Law requiring disclosure of power consumption in the normal use (idle mode) and standby modes. Your product is one of many configurations in this model family; the idle mode power consumption of your specific configuration may vary from the information on the label. Actual power consumption of your product may be higher or lower than the value reported on the Mexico product energy label due to factors such as configuration

(components and modules chosen) and usage (tasks being performed, software installed and running, etc.). Turkey EEE regulation Trkiye Cumhuriyeti: EEE Ynetmeliine Uygundur Ukraine restriction of hazardous substances (RoHS) The equipment complies with requirements of the Technical Regulation, approved by the Resolution of Cabinet of Ministry of Ukraine as of December 3, 2008 1057, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment.

, 3 2008 1057. Perchlorate materialspecial handling may apply See http://www.dtsc.ca.gov/hazardouswaste/perchlorate. This products real-time clock battery or coin cell battery may contain perchlorate and may require special handling when recycled or disposed of in California. India restriction of hazardous substances (RoHS) 41 6 Environmental notices for desktops, thin clients and personal workstations This chapter provides country- and region-specific environmental notices and compliance information. Some of these notices may not apply to your product. Electronic hardware, packaging and battery recycling HP encourages customers to recycle used electronic hardware, HP original print cartridges packaging, and rechargeable batteries. For more information about recycling programs, go to http://www.hp.com/recycle. For information about recycling the product in Japan, refer to http://www.hp.com/jp/hardwarerecycle/. Disposal of waste equipment by users This symbol means do not dispose of your product with your other household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment. For more information, please contact your household waste disposal service or go to http://www.hp.com/recycle. Brazil alkaline battery disposal HEWLETT PACKARD BRASIL LTDA (HP) AV. JOS LUIZ MAZALI N 360 - GALPO B-PARTE 1-BAIRRO RESIDENCIAL BURCK - LOUVEIRA/SP - CEP: 13290-000 CNPJ: 61.797.924/0007-40 Centro de Informaes HP: (11) 4004-7751 ou 0800-7097751 No descarte o produto eletrnico em lixo comum Este produto eletroeletrnico e seus componentes no devem ser descartados no lixo comum, pois embora estejam em conformidade com padres mundiais de restrio a substncias nocivas, podem conter, ainda que em quantidades mnimas, substncias impactantes ao meio ambiente. Ao final da vida til deste produto, o usurio dever entreg-lo HP. A no observncia dessa orientao sujeitar o infrator s sanes previstas em lei. Aps o uso, as pilhas e/ou baterias dos produtos HP devero ser entregues ao estabelecimento comercial ou rede de assistncia tcnica autorizada pela HP. Para maiores informaes , inclusive sobre os pontos de recebimento, acesse: http://www.hp.com.br/reciclar 42 Chapter 6 Environmental notices for desktops, thin clients and personal workstations Brazil hardware recycling information HEWLETT PACKARD BRASIL LTDA (HP) AV. JOS LUIZ MAZALI N 360 - GALPO B-PARTE 1-BAIRRO RESIDENCIAL BURCK - LOUVEIRA/SP - CEP: 13290-000 CNPJ: 61.797.924/0007-40 Centro de Informaes HP: (11) 4004-7751 ou 0800-7097751 No descarte o produto eletrnico em lixo comum Este produto eletroeletrnico e seus componentes no devem ser descartados no lixo comum, pois embora estejam em conformidade com padres mundiais de restrio a substncias nocivas, podem conter, ainda que em quantidades mnimas, substncias impactantes ao meio ambiente. Ao final da vida til deste produto, o usurio dever entreg-lo HP. A no observncia dessa orientao sujeitar o infrator s sanes previstas em lei. Aps o uso, as pilhas e/ou baterias dos produtos HP devero ser entregues ao estabelecimento comercial ou rede de assistncia tcnica autorizada pela HP. Para maiores informaes , inclusive sobre os pontos de recebimento, acesse: http://www.hp.com.br/reciclar ENERGY STAR Certification (select models only) ENERGY STAR is a U.S. Environmental Protection Agency voluntary program that helps businesses and individuals save money and protect our climate through superior energy efficiency. Products that earn the ENERGY STAR prevent greenhouse gas emissions by meeting strict energy efficiency criteria or requirements set by the U.S. Environmental Protection Agency. As an ENERGY STAR Partner, Hewlett-Packard Company has followed the U.S. EPAs enhanced product certification process to ensure that products marked with the ENERGY STAR logo are ENERGY STAR certified per the applicable ENERGY STAR guidelines. The following logo appears on all ENERGY STAR-certified computers::

A key ENERGY STAR requirement for computer products is power management features that significantly reduce energy consumption when the product is not in use. Power management allows a computer to automatically enter a low power sleep mode, or other low power mode, after a defined period of inactivity. The power management features have been preset as follows when the computer is operating on AC power:

Computer type Time to activate display sleep mode Time to activate computer sleep mode (minutes) Resuming from sleep mode Desktops, Integrated Desktops, Workstations Less than or equal to 15 minutes (varies by model) Less than or equal to 30 minutes (varies by model) Thin clients Less than or equal to 15 minutes (varies by model) Less than or equal to 30 minutes when sleep mode is supported by the operating system (varies by model) Product will exit sleep mode when user interacts with any input device, including the mouse or keyboard. If Wake-on-Lan (WOL) is enabled, the system can resume from sleep in response to a network signal. When sleep mode is supported by operating system product will exit sleep mode when user interacts with any input device, including the mouse or keyboard. Brazil hardware recycling information 43 Computer type Time to activate display sleep mode Time to activate computer sleep mode (minutes) Resuming from sleep mode If Wake-on-Lan (WOL) is enabled, the system can resume from sleep in response to a network signal. The computer exits Sleep when the power/Sleep button is pressed. When the Wake On LAN (WOL) feature is enabled, the computer can also exit Sleep in response to a network signal. Additional information on the potential energy and financial savings of the power management feature can be found on the EPA ENERGY STAR Power Management Web site at http://www.energystar.gov/

powermanagement. Additional information on the ENERGY STAR program and its environmental benefits are available on the EPA ENERGY STAR Web site at http://www.energystar.gov. ENERGY STAR and the ENERGY STAR mark are registered trademarks owned by the U.S. Environmental Protection Agency. Chemical substances HP is committed to providing our customers with information about the chemical substances in our products as needed to comply with legal requirements such as REACH (Regulation EC No. 1907/2006 of the European Parliament and the Council). A chemical information report for this product can be found at http://www.hp.com/go/reach. Mercury statement This statement applies to All-in-One computers with built-in display panels that do not use LED backlighting. This HP product may contain the following material that might require special handling at end-of-life:

Mercury in the fluorescent lamp in the display LCD Disposal of mercury can be regulated because of environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance (EIA)

(http://www.eiae.org). Perchlorate materialspecial handling may apply The computers real-time clock battery may contain perchlorate and may require special handling when recycled or disposed of in California. See http://www.dtsc.ca.gov/hazardouswaste/perchlorate/. China environmental notices http://www.hp.com/hpinfo/globalcitizenship/environment/productdata/chinasepa.html 44 Chapter 6 Environmental notices for desktops, thin clients and personal workstations http://www.hp.com.cn/hardwarerecycle

:

(, ) ,,,

,,,, (http://

www.sepa.gov.cn), 3

:

China PC energy label In accordance with The Regulation of the Implementation on China Energy Label for Microcomputers

(CEL-30), this microcomputer has an Energy Efficiency Label. The energy efficiency grade, TEC (Typical Energy Consumption), and product category presented on the label are determined and calculated according to the standard GB28380-2012. 1. Energy Efficiency Grades The grade is determined by the standard with the calculation of base consumption level with the sum of all the allowances for additional components such as main memory and graphics card. For products of any grade, the TEC should not exceed the value specified in the following table:

Product Type Grade 1 Grade 2 Grade 3 TEC (kilowatt hour) Desktop microcomputer, AIO Category A 98.0+Efa 148.0+Efa 198.0+Efa Portable Computer Category B Category C Category D Category A Category B Category C 125.0+Efa 159.0+Efa 184.0+Efa 20.0+Efa 26.0+Efa 54.5+Efa 175.0+Efa 225.0+Efa 209.0+Efa 259.0+Efa 234.0+Efa 284.0+Efa 35.0+Efa 45.0+Efa 75.0+Efa 45.0+Efa 65.0+Efa 123.5+Efa NOTE: Efa is the sum of power factor of product additional functions. 2. Typical Energy Consumption The energy consumption figure presented on the label is the data measured with the representative configuration that covers all the configurations in the registration unit which is selected according to CEL-30. Thus, actual energy consumption of this specific microcomputer may not be the same as the TEC data presented in the label. 3. Product Category The product category is determined by the standard according to the microcomputers configuration. The categorization of products complies with the regulations in the following table:

China PC energy label 45 Product Type Category A Category B Category C Configuration Description Desktop microcomputer, AIO Portable Computer The desktop microcomputer and AIO whose configuration is out of the scope of Category B, C, and D The portable computer whose configuration is out of the scope of Category B and C CPU physical core number of 2, and system memory of not less than 2GB A Discrete GPU CPU physical core number of over 2, with at least one of the following features:

1. 2. System memory of not less than 2 GB A Discrete GPU The product that has a CPU physical core number of not less than 2, system memory of not less than 2GB, A Discrete GPU with Frame Buffer Width not less than 128-bit. Category D CPU physical core number of not less than 4, with at least one of the following features:

1. 2. System memory of not less than 4 GB A Discrete GPU with Frame Buffer Width not less than 128-bit For more details on the specification, please refer to the standard GB28380-2012. CEL30 GB28380 2012:

1.

() A B C D A B C 1 2 3 98.0+Efa 148.0+Efa 198.0+Efa 125.0+Efa 175.0+Efa 225.0+Efa 159.0+Efa 209.0+Efa 259.0+Efa 184.0+Efa 234.0+Efa 284.0+Efa 20.0+Efa 35.0+Efa 45.0+Efa 26.0+Efa 45.0+Efa 65.0+Efa 54.5+Efa 75.0+Efa 123.5+Efa Efa 2. 46 Chapter 6 Environmental notices for desktops, thin clients and personal workstations 3. A B C D B C D CPU 2 2GB CPU 2 a. a 2GB b. GPU) B C GPU CPU 2 2GB GPU 128

. CPU 4 a. 4GB b. GPU 128 GB28380-2012 China PC energy label 47 China restriction of hazardous substances (RoHS) As required by China's Management Methods for Controlling Pollution by Electronic Information Products Hazardous Substances and Elements Part Name Lead

(Pb) Mercury

(Hg) Cadmium

(Cd) Hexavalent Chromium

(Cr(VI)) Polybromi-

nated biphenyls

(PBB) Polybromi-

nated diphenyl ethers (PBDE) Motherboard, processor and heat sink Memory I/O PCAs Power supply Keyboard Mouse Chassis/Other Fans Internal/External Media Reading Devices External Control Devices Cable Hard Disk Drive Display X X X X X X X X X X X X X O O O O O O O O O O O O X O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O This form has been prepared in compliance with the provisions of SJ/T 11364. O: Indicates that the content of said hazardous substance in all of the homogenous materials in the component is within the limits required by GB/T 26572. X: Indicates that the content of said hazardous substance exceeds the limits required by GB/T 26572 in at least one homogenous material in the component. All parts named in this table with an X are in compliance with the European Unions RoHS Legislation. NOTE: The referenced Environmental Protection Use Period Marking was determined according to normal operating use conditions of the product such as temperature and humidity. 48 Chapter 6 Environmental notices for desktops, thin clients and personal workstations The Table of Hazardous Substances/Elements and their Content I/O PCAs

/

/

(Pb)

(Hg)

(Cd)

(Cr(VI))

(PBB)

(PBDE) X X X X X X X X X X X X X O O O O O O O O O O O O X O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O SJ/T 11364 O GB/T 26572 X GB/T 26572 X RoHS China restriction of hazardous substances (RoHS) 49 India restriction of hazardous substances (RoHS) This product complies with the India E-waste (Management and Handling) Rule 2011 and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule. IT ECO declarations Desktop PCs and Thin Clients http://www.hp.com/hpinfo/globalcitizenship/environment/productdata/itecodesktop-pc.html?

jumpid=reg_R1002_USEN Workstations http://www.hp.com/hpinfo/globalcitizenship/environment/productdata/itecoworkstatio.html Japan restriction of hazardous substances (RoHS) 2008 JISC0950 2006 7 http://www.hp.com/go/jisc0950 A Japanese regulatory requirement, defined by specification JIS C 0950, 2008, mandates that manufacturers provide Material Content Declarations for certain categories of electronic products offered for sale after July 1, 2006. To view the JIS C 0950 material declaration for this product, visit http://www.hp.com/go/jisc0950. Ley para el Aprovechamiento Sustentable de la Energa de Mxico (Mexico Sustainable Energy Use Law) Se ha etiquetado este producto en conformidad con la Ley para el Aprovechamiento Sustentable de la Energa de Mxico, que requiere la divulgacin del consumo de energa del modo de uso normal (modo inactivo) y del modo de espera. Su producto es una de las muchas configuraciones de esta familia de modelos; el consumo de energa del modo inactivo de su configuracin especfica puede diferir de la informacin de la etiqueta. El consumo real de energa de su producto puede ser mayor o menor que el valor informado en la etiqueta de energa de producto para Mxico a causa de factores como la configuracin

(componentes y mdulos seleccionados) y el uso (tareas que se estn efectuando, software instalado y en ejecucin, etc.). NOTE: Esta ley no es aplicable a los workstations. This product has been labeled in compliance with the Mexico Sustainable Energy Use Law requiring disclosure of power consumption in the normal use (idle mode) and standby modes. Your product is one of many configurations in this model family; the idle mode power consumption of your specific configuration may vary from the information on the label. Actual power consumption of your product may be higher or lower than the value reported on the Mexico product energy label due to factors such as configuration

(components and modules chosen) and usage (tasks being performed, software installed and running, etc.). NOTE: Workstations are not labeled because the law is not applicable to the workstation product category. 50 Chapter 6 Environmental notices for desktops, thin clients and personal workstations Turkey EEE regulation Trkiye Cumhuriyeti: EEE Ynetmeliine Uygundur

(Ukraine restriction of hazardous substances (RoHS))

, 3 2008 1057. The equipment complies with requirements of the Technical Regulation, approved by the Resolution of Cabinet of Ministry of Ukraine as of December 3, 2008 1057, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment. TCO Certified Edge Certification This section applies only to products bearing the TCO Certified Edge logo. Turkey EEE regulation 51 52 Chapter 6 Environmental notices for desktops, thin clients and personal workstations Index A airline travel notice 8 altitude notice 25, 31 B battery notice 8, 23, 41 battery recycling 33 Brazil notice 3 C cable grounding notice 25 Canada modem statement 12 Canada notices 4 China environmental notices 35, 44 China PC energy label 35, 45 China restriction of hazardous substances notice 38, 48 D Declaration of Conformity notebook computers 3 disposal notices battery 41 battery, user replacement 8 equipment 33 factory sealed battery 8 E electronic hardware and battery recycling 33 ENERGY STAR certification 34, 43 environmental notices 33 equipment disposal notice 33 ergonomics notice 5, 20 European Union notices 4, 19 F Federal Communications Commission desktops, thin clients and workstations notice 17 desktops, thin clients, workstations cables 17 desktops, thin clients, workstations modifications 17 notebook computers cables 2 notebook computers modifications 2 modifications, notebook computers Federal Communications notebook computers notice 2 Commission 2 G GS Notice 5, 20 H headset and earphone volume level notice 24 I India restriction of hazardous substances notice 41, 50 J Japan modem statement 12 Japan notice 6 Japan power cord notice 13 Japan restriction of hazardous substances notice 41, 50 K keyboard notice 24 L labels, regulatory 1 laser safety notice 9 M Macrovision Corporation notice 13 Mexico Sustainable Energy Use Law 41 Mexico wireless notice 6 modem notices 9 modem statements Canada 12 Japan 12 New Zealand 12 U.S. 10 modifications, desktops, thin clients, workstations Federal Communications Commission 17 N New Zealand modem statement 12 notices airline travel 8 battery 8, 41 battery, user replacement 23 Brazil 3 Canada 4 China restriction of hazardous substances 38, 48 environmental 33 equipment disposal 33 ergonomics 5, 20 European Union 4, 19 headset and earphone volume level 24 India restriction of hazardous substances 41, 50 Japan 6 Japan power cord 13 Japan restriction of hazardous substances 41, 50 keyboard 24 laser safety 9 Macrovision Corporation 13 Mexico 6 modem 9 perchlorate material 41 power cords 13, 24 Singapore 7 South Korea 6 Taiwan 7, 21 Thailand WWAN wireless notice 7 travel 24 Ukraine restriction of hazardous substances 41, 51 notices, desktops, thin clients and workstations Federal Communications Commission 17 Index 53 notices, notebook computers Federal Communications Commission 2 P power cord notice 13, 24 R recycling, electronic hardware and battery 33 S Singapore wireless notice 7 South Korea notice 6 T Taiwan notice 7, 21 TCO Certified Edge Certification 51 Thailand WWAN wireless notice 7 travel notice 24 tropical warning notice 25, 31 TV tuner, cable grounding notice 25 U U.S. modem statement 10 Ukraine restriction of hazardous substances notice 41, 51 V voice support 13 volume level notice, headset and earphone 24 W wireless LAN devices 3, 18, 19 54 Index

Regulatory, Safety and Environmental Notices User Guide Copyright 2014 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. ENERGY STAR and the ENERGY STAR mark are registered trademarks owned by the U.S. Environmental Protection Agency. Java is a trademark of Sun Microsystems. Microsoft and Windows are U.S. registered trademarks of the Microsoft group of companies. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Second Edition: October 2014 First Edition: June 2014 Document Part Number: 786097-002 About This Guide This guide provides regulatory, safety and environmental information that is compliant with U.S., Canadian, and international regulations for notebook computers, desktops, thin clients and personal workstations. WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. NOTE: Text set off in this manner provides important supplemental information. iii iv About This Guide Table of contents 1 Regulatory notices for notebook computers .................................................................................................... 1 Accessing regulatory labels .................................................................................................................................. 1 Federal Communications Commission notice ....................................................................................................... 2 Modifications ....................................................................................................................................... 2 Cables .................................................................................................................................................. 2 Declaration of Conformity for products marked with the FCC logo (United States only) ................. 3 Products with wireless LAN devices or HP Mobile Broadband Modules ............................................ 3 Brazil notice ........................................................................................................................................................... 3 Canada notices ....................................................................................................................................................... 4 European Union regulatory notices ...................................................................................................................... 4 Declaration of Conformity ................................................................................................................... 4 Products with wireless functionality (EMF) ...................................................................... 5 Restrictions for product with wireless functionality ....................................................... 5 European telephone network declaration (Modem/Fax) ................................................. 5 Ergonomics notice ............................................................................................................ 5 Germany (English text) ................................................................................... 5 Germany (Deutscher text) .............................................................................. 5 Australia and New Zealand notice ......................................................................................................................... 6 Japan notice ........................................................................................................................................................... 6 Wireless LAN, Wireless WAN, and Bluetooth certification markings ................................................. 6 South Korea notices ............................................................................................................................................... 6 Mexico notice ......................................................................................................................................................... 6 Singapore wireless notice ..................................................................................................................................... 7 Thailand WWAN wireless notice ............................................................................................................................ 7 Taiwan NCC notices ................................................................................................................................................ 7 Wireless LAN 802.11a devices ............................................................................................................ 7 Wireless LAN 802.11 devices/Bluetooth devices/Short range devices ............................................. 8 Airline travel notice ................................................................................................................................................ 8 User-replaceable battery notices .......................................................................................................................... 8 Factory-sealed battery notices ............................................................................................................................. 8 Laser compliance ................................................................................................................................................... 9 Modem notices ....................................................................................................................................................... 9 Telecommunications device approvals .............................................................................................. 9 U.S. modem statements ................................................................................................................... 10 U.S. modem declarations .................................................................................................................. 11 Canada modem statements .............................................................................................................. 12 v Japan modem statements ................................................................................................................ 12 New Zealand modem statements ..................................................................................................... 12 Voice support .................................................................................................................. 13 Power cord notice ................................................................................................................................................ 13 Japan power cord notice ................................................................................................................... 13 DC plug of external HP power supply ............................................................................................... 13 Macrovision Corporation notice .......................................................................................................................... 13 2 Regulatory notices for desktops, thin clients and personal workstations ........................................................ 14 Modem notices .................................................................................................................................................... 14 Telecommunications device approvals ............................................................................................ 14 U.S. modem statements ................................................................................................................... 14 Canadian modem statements ........................................................................................................... 15 Japanese modem statements .......................................................................................................... 15 New Zealand modem statements ..................................................................................................... 16 Voice support .................................................................................................................. 16 Electromagnetic compatibility notices ............................................................................................................... 16 Federal Communications Commission notice .................................................................................. 17 Modifications ................................................................................................................... 17 Cables .............................................................................................................................. 17 Declaration of conformity for products marked with the FCC logo (United States only) ................................................................................................................................ 17 Products with wireless LAN devices ............................................................................... 17 Australia telecom statement ............................................................................................................ 18 Brazil notice ....................................................................................................................................... 19 Canadian notice ................................................................................................................................. 19 European Union regulatory notices .................................................................................................. 19 Declaration of Conformity .............................................................................................. 19 Products with wireless functionality (EMF) ................................................. 19 Restrictions for product with wireless functionality ................................... 20 European telephone network declaration (Modem/Fax) ............................ 20 Ergonomics notice ........................................................................................ 20 Japan notice ...................................................................................................................................... 20 Wireless LAN and Bluetooth certification markings ...................................................... 20 South Korea notices .......................................................................................................................... 20 Mexico notice ..................................................................................................................................... 21 Taiwan NCC notices ........................................................................................................................... 21 Wireless LAN 802.11a devices ........................................................................................ 21 Wireless LAN 802.11 devices/Bluetooth devices/Short range devices ......................... 22 vi 3 Safety notices for notebook computers ......................................................................................................... 23 Heat-related safety warning notice .................................................................................................................... 23 Potential safety conditions notice ...................................................................................................................... 23 User-replaceable battery notices ....................................................................................................................... 23 Headset and earphone volume level notice ....................................................................................................... 24 Power cord notices .............................................................................................................................................. 24 Brazil notice ....................................................................................................................................... 24 Cleaning the keyboard ......................................................................................................................................... 24 Travel notice ........................................................................................................................................................ 24 China safety notices ............................................................................................................................................ 25 China: Altitude notice ........................................................................................................................ 25 China: Tropical warning notice .......................................................................................................... 25 Norway and Sweden: Cable grounding notice for products with a TV tuner ...................................................... 25 Taiwan BSMI notice .............................................................................................................................................. 25 4 Safety notices for desktops, thin clients and personal workstations ............................................................... 26 Important safety information ............................................................................................................................. 26 Installation conditions ......................................................................................................................................... 26 Battery replacement notice ................................................................................................................................ 27 Headset and earphone volume level notice ....................................................................................................... 27 Laser safety ......................................................................................................................................................... 28 Power supply and power cord set requirements ................................................................................................ 28 Power supply class I grounding requirements ................................................................................. 28 Brazil notice .................................................................................................................... 28 Denmark .......................................................................................................................... 28 Finland ............................................................................................................................. 28 Norway ............................................................................................................................ 28 Sweden ............................................................................................................................ 28 Power supply requirements .............................................................................................................. 28 For use in Norway ........................................................................................................... 29 Power cord set requirements ........................................................................................................... 29 Japan power cord requirements ....................................................................................................... 29 Pinch hazard ........................................................................................................................................................ 29 TV antenna connectors protection ...................................................................................................................... 30 External television antenna grounding ............................................................................................ 30 Lightning protection .......................................................................................................................... 30 Note to CATV system installer .......................................................................................................... 30 China safety notices ............................................................................................................................................ 31 China: Altitude notice ........................................................................................................................ 31 China: Tropical warning notice .......................................................................................................... 31 Germany acoustics notice ................................................................................................................................... 32 vii Taiwan BSMI notice .............................................................................................................................................. 32 5 Environmental notices for notebook computers ............................................................................................ 33 Electronic hardware, packaging and battery recycling ...................................................................................... 33 Disposal of waste equipment by users ............................................................................................................... 33 Brazil alkaline battery disposal ........................................................................................................................... 33 Brazil hardware recycling information ............................................................................................................... 34 ENERGY STAR Certification (select models only) .............................................................................................. 34 Chemical substances ........................................................................................................................................... 35 China environmental notices ............................................................................................................................... 35 China PC energy label .......................................................................................................................................... 35 China restriction of hazardous substances (RoHS) ............................................................................................. 38 India restriction of hazardous substances (RoHS) .............................................................................................. 41 Japan restriction of hazardous substances (RoHS) ............................................................................................ 41 Mexico Sustainable Energy Use Law ................................................................................................................... 41 Turkey EEE regulation ......................................................................................................................................... 41 Ukraine restriction of hazardous substances (RoHS) ......................................................................................... 41 Perchlorate materialspecial handling may apply ........................................................................................... 41 6 Environmental notices for desktops, thin clients and personal workstations ................................................... 42 Electronic hardware, packaging and battery recycling ...................................................................................... 42 Disposal of waste equipment by users ............................................................................................................... 42 Brazil alkaline battery disposal ........................................................................................................................... 42 Brazil hardware recycling information ............................................................................................................... 43 ENERGY STAR Certification (select models only) .............................................................................................. 43 Chemical substances ........................................................................................................................................... 44 Mercury statement .............................................................................................................................................. 44 Perchlorate materialspecial handling may apply ............................................................................................. 44 China environmental notices ............................................................................................................................... 44 China PC energy label .......................................................................................................................................... 45 China restriction of hazardous substances (RoHS) ............................................................................................. 48 The Table of Hazardous Substances/Elements and their Content .................................................. 49 India restriction of hazardous substances (RoHS) .............................................................................................. 50 IT ECO declarations .............................................................................................................................................. 50 Japan restriction of hazardous substances (RoHS) ............................................................................................ 50 Ley para el Aprovechamiento Sustentable de la Energa de Mxico (Mexico Sustainable Energy Use Law) .... 50 Turkey EEE regulation ......................................................................................................................................... 51

(Ukraine restriction of hazardous substances

(RoHS)) ................................................................................................................................................................. 51 TCO Certified Edge Certification .......................................................................................................................... 51 viii Index ............................................................................................................................................................. 53 ix x 1 Regulatory notices for notebook computers This chapter provides country- and region-specific non-wireless and wireless regulatory notices and compliance information for the computer product. Some of these notices may not apply to your product. One or more integrated wireless devices may be installed. In some environments, the use of wireless devices may be restricted. Such restrictions may apply onboard airplanes, in hospitals, near explosives, in hazardous locations, and so on. If you are uncertain of the policy that applies to the use of this product, ask for authorization to use it before you turn it on. Accessing regulatory labels Regulatory labels, which provide country or regional regulatory information (for example, FCC ID), may be physically located on the bottom of the computer, inside the battery bay (select models only), under the removable service door (select models only), on the back of the display, or on the wireless or modem module. Some products may also provide electronic regulatory labels (e-labels) for radio modules in your computer. Electronic labels can be accessed through the system BIOS. NOTE: Electronic labels are not available on all products. NOTE: Devices not for sale or use in the United States may not contain a FCC ID. To view electronic regulatory labels:

1. 2. 3. 4. Turn on or restart the computer, and then press esc while the Press the ESC key for Startup Menu message is displayed at the bottom of the screen. Press f10 to enter Computer Setup. Use a pointing device or the arrow keys to select Advanced, select Electronic Labels, and then press enter. To view an electronic label, use a pointing device or the arrow keys to select one of the listed items, and then press OK. NOTE: The list of available electronic label items varies depending on the computer model and installed devices. 5. To exit Computer Setup menus without saving your changes:

Select the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions. or Use the arrow keys to select Main, select Ignore Changes and Exit, and then press enter. Accessing regulatory labels 1 Federal Communications Commission notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio or television technician for help. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by HP may void the user's authority to operate the equipment. Cables To maintain compliance with FCC Rules and Regulations, connections to this device must be made with shielded cables having metallic RFI/EMI connector hoods. 2 Chapter 1 Regulatory notices for notebook computers Declaration of Conformity for products marked with the FCC logo (United States only) This device complies with Part 15 of the FCC Rules. Operation is subject to the following 2 conditions:

1. 2. This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. If you have questions about the product that are not related to this declaration, write to Hewlett-Packard Company P. O. Box 692000, Mail Stop 530113 Houston, TX 77269-2000 For questions regarding this FCC declaration, write to Hewlett-Packard Company P. O. Box 692000, Mail Stop 510101 Houston, TX 77269-2000 or call HP at 281-514-3333 To identify your product, refer to the part, series, or model number located on the product. Products with wireless LAN devices or HP Mobile Broadband Modules This device must not be co-located or operating in conjunction with any other antenna or transmitter. WARNING! Exposure to Radio Frequency Radiation The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact is minimized during normal operation of tablet PCs and notebook computers. During normal operation of tablet PCs and notebook computers with displays equal to or less than 30.5 cm

(12 inches): To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antennas should not be less than 2.5 cm (1 inch). To identify the location of the wireless antennas, refer to the computer user guides included with your computer. During normal operation of notebook computers with displays greater than 30.5 cm (12 inches): To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antennas should not be less than 20 cm (8 inches), including when the computer display is closed. To identify the location of the wireless antennas, refer to the computer user guides included with your computer. CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15- to 5.25-GHz frequency range. The FCC requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel mobile satellite systems. High-power radar is allocated as the primary user of the 5.25- to 5.35-GHz and 5.65- to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device. Brazil notice Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio. Brazil notice 3 Este equipamento atende aos limites de Taxa de Absoro Especfica referente exposio a campos eltricos, magnticos e eletromagnticos de radiofreqncias adotados pela ANATEL. Ao operar o dispositivo a uma distncia muito prxima do seu corpo, utilize um acessrio de armazenamento no metlico para posicionar o dispositivo a uma distncia mnima de 1,5 cm do corpo. Canada notices This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations, CAN ICES-3(B)/NMB-3(B). If this device has WLAN or Bluetooth capability, the device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. WARNING! Exposure to Radio Frequency Radiation: The radiated output power of this device is below the Industry Canada radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact is minimized during normal operation. During normal operation of tablet PCs and notebook computers with displays equal to or less than 30.5 cm

(12 inches): To avoid the possibility of exceeding the Industry Canada radio frequency exposure limits, human proximity to the antennas should not be less than 2.5 cm (1 inch). To identify the location of the wireless antennas, refer to the computer user guides included with your computer. During normal operation of notebook computers with displays greater than 30.5 cm (12 inches): To avoid the possibility of exceeding the Industry Canada radio frequency exposure limits, human proximity to the antennas should not be less than 20 cm (8 inches), including when the computer display is closed. To identify the location of the wireless antennas, refer to the computer user guides included with your computer. CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15- to 5.25-GHz frequency range. Industry Canada requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-

channel mobile satellite systems. High-power radar is allocated as the primary user of the 5.25- to 5.35-GHz and 5.65- to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device. The antennas for this device are not replaceable. Any attempt at user access will damage your computer. European Union regulatory notices Declaration of Conformity Products bearing the CE marking comply with one or more of the following EU Directives as may be applicable:

Low Voltage Directive 2006/95/EC; EMC Directive 2004/108/EC; Ecodesign Directive 2009/125/EC; R&TTE Directive 1999/5/EC; RoHS Directive 2011/65/EU Compliance with these directives is assessed using applicable European Harmonised Standards. The full Declaration of Conformity can be found at the following web site: www.hp.eu/certificates (Search with the product model name or its Regulatory Model Number (RMN), which may be found on the regulatory label.) 4 Chapter 1 Regulatory notices for notebook computers The point of contact for regulatory matters is Hewlett-Packard GmbH, Dept./MS:HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, GERMANY. Products with wireless functionality (EMF) This product meets international guidelines (ICNIRP) for exposure to radio frequency radiation. This product incorporates a radio transmitting and receiving device. For notebook computers in normal use, a separation distance of 20 cm ensures that radio frequency exposure levels comply with EU requirements. Products designed to be operated at closer proximities, such as tablet computers, comply with applicable EU requirements in typical operating positions, but a minimum distance of 1 cm should be maintained from the antennas. Restrictions for product with wireless functionality This product is designed for use without restrictions in all EU countries, plus Iceland, Liechtenstein, Norway, and Switzerland. European telephone network declaration (Modem/Fax) The product herewith complies with the requirements of the R&TTE Directive 1999/5/EC (Annex II) and carries the CE marking accordingly. However, due to differences between the individual PSTNs provided in different countries/regions, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems, you should contact your equipment supplier in the first instance. Ergonomics notice Germany (English text) When a mobile computer is used at the office workstation for display work tasks where the Visual Display Unit (VDU) Directive 90/270/EEC is applicable, an adequate external keyboard is required. Depending on the application and task, an adequate external monitor may also be necessary to attain working conditions comparable to a workstation setup. Ref: EK1-ITB 2000 (voluntary GS certification) Mobile computers bearing the "GS" approval mark meet the applicable ergonomic requirements. Without external keyboards, they are suitable only for short-time use of VDU tasks. During mobile use with disadvantageous illumination conditions (e.g. direct sun light) reflections may occur, which result in reduced readability. Germany (Deutscher text) Wird ein mobiler Computer fr Bildschirmarbeitsaufgaben verwendet, wo die Richtlinie 90/270/EEG

(Bildschirmarbeitsrichtlinie) anzuwenden ist, wird eine geeignete externe Tastatur notwendig. Abhngig von der Anwendung und der Aufgabe kann ein geeigneter externer Monitor erforderlich sein, um vergleichbare Arbeitsbedingungen zu einem stationren Arbeitsplatz zu erreichen. Ref: EK1-ITB 2000 (freiwillige GS Zertifizierung) Mobile Computer, welche das "GS" Zeichen tragen, entsprechen den ergonomischen Anforderungen und sind nur fr kurzzeitige Benutzung von Bildschirmarbeitsaufgaben geeignet. Bei mobiler Nutzung mit ungnstigen Lichtverhltnissen (z.B. direkte Sonneneinstrahlung) kann es zu Reflexionen und damit zu Einschrnkungen der Lesbarkeit der dargestellten Zeichen kommen. European Union regulatory notices 5 Australia and New Zealand notice This equipment incorporates a radio transmitting and receiving device. In normal use, a separation distance of 20 cm ensures that radio frequency exposure levels comply with the Australian and New Zealand Standards. Japan notice Wireless LAN, Wireless WAN, and Bluetooth certification markings This product contains certified radio equipment. South Korea notices B ( )

(B) ,

.

(

).

, 2.5cm

. Mexico notice Declaracin para Mxico La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. If your product is provided with wireless accessories such as a keyboard or mouse and you need to identify the model of the accessory, refer to the label included on that accessory. 6 Chapter 1 Regulatory notices for notebook computers Singapore wireless notice Turn off any WWAN devices while you are onboard aircraft. The use of these devices onboard aircraft is illegal, may be dangerous to the operation of the aircraft, and may disrupt the cellular network. Failure to observe this instruction may lead to suspension or denial of cellular services to the offender, or legal action, or both. Users are reminded to restrict the use of radio equipment in fuel depots, chemical plants, and where blasting operations are in progress. As with other mobile radio transmitting equipment, users are advised that for satisfactory operation of the equipment and for the safety of personnel, no part of the human body should be allowed to come too close to the antennas during operation of the equipment. This device has been designed to comply with applicable requirements for exposure to radio waves, based on scientific guidelines that include margins intended to assure the safety of all people, regardless of health and age. These radio wave exposure guidelines employ a unit of measurement known as the specific absorption rate (SAR). Tests for SAR are conducted using standardized methods, with the phone transmitting at its highest certified power level in all used frequency bands. The SAR data information is based on CENELEC's standards EN50360 and EN50361, which use the limit of 2 watts per kilogram, averaged over 10 grams of tissue. Thailand WWAN wireless notice This telecom equipment has complied with NTC regulations. Taiwan NCC notices Wireless LAN 802.11a devices Singapore wireless notice 7 Wireless LAN 802.11 devices/Bluetooth devices/Short range devices Airline travel notice Use of electronic equipment onboard commercial aircraft is at the discretion of the airline. User-replaceable battery notices When a battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for computer battery disposal. HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, refer to the HP Web site at http://www.hp.com/

recycle. For information about removing a user-replaceable battery, refer to the user guide included with the product. Factory-sealed battery notices The battery[ies] in this product cannot be easily replaced by users themselves. Removing or replacing the battery could affect your warranty coverage. If a battery is no longer holding a charge, contact support. When a battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for battery disposal. 8 Chapter 1 Regulatory notices for notebook computers Laser compliance WARNING! Use of controls or adjustments, or performance of procedures other than those specified in the laser product installation guide, may result in hazardous radiation exposure. To reduce the risk of exposure to hazardous radiation:

Do not try to open the module enclosure. There are no user-serviceable components inside. Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified in the laser product installation guide. Allow only authorized service providers to repair the unit. This product may be provided with an optical storage device (for example, a CD or DVD drive) and/or a fiber optic transceiver. Each of these devices that contain a laser is classified as a Class 1 Laser Product in accordance with IEC/EN 60825-1 and meets the requirements for safety of that standard. Each laser product complies with US FDA regulations of 21 CFR 1040.10 and 1040.11 or complies with those regulations except for deviations pursuant to Laser Notice No. 50 dated June 24, 2007. Modem notices WARNING! To reduce the risk of fire, electric shock, and injury to persons when using this device, always follow basic safety precautions, including the following:

Do not use this product near waterfor example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Avoid using this product during an electrical storm. There is a remote risk of electric shock from lightning. Do not use this product to report a gas leak while in the vicinity of the leak. Always disconnect the modem cable before opening the equipment enclosure or touching an uninsulated modem cable, jack, or internal component. If this product was not provided with a telephone line cord, use only No. 26 AWG or larger telecommunication line cord. Do not plug a modem or telephone cable into the RJ-45 (network) jack. SAVE THESE INSTRUCTIONS. Telecommunications device approvals The telecommunications device in the computer is approved for connection to the telephone network in the countries and regions whose approval markings are indicated on the product label located on the bottom of the computer or on the modem. Refer to the user guide included with the product to ensure that the product is configured for the country or region in which the product is located. Selecting a country or region other than the one in which it is located may cause the modem to be configured in a way that violates the telecommunication regulations/laws of Laser compliance 9 that country or region. In addition, the modem may not function properly if the correct country or region selection is not made. If, when you select a country or region, a message appears that states that the country or region is not supported, this means that the modem has not been approved for use in this country or region and thus should not be used. U.S. modem statements This equipment complies with Part 68 of the FCC Rules and the requirements adopted by the ACTA. On the bottom of the computer or on the modem is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. Provide this information to the telephone company if you are requested to do so. Applicable certification jack USOC = RJ11C. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all locations, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. If this HP equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But, if advance notice isn't practical, the telephone company will notify you as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes to its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted telephone service. If trouble is experienced with this equipment, call technical support. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. You should perform repairs only to the equipment specifically discussed in the Troubleshooting section of the user guide, if one is provided. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission, or corporation commission for information. If your home has specially wired alarm equipment connected to the telephone line, ensure that the installation of this HP equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including a fax machine, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page, or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity, or other individual sending the message, and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-

distance transmission charges). In order to program this information into your fax machine, you should complete the steps outlined in the faxing software instructions. 10 Chapter 1 Regulatory notices for notebook computers U.S. modem declarations Refer to the following modem vendor declarations for the modem device installed in your computer:

Modem notices 11 Canada modem statements This equipment meets the applicable Industry Canada technical specifications. The Ringer Equivalence Number, REN, is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices, subject only to the requirement that the sum of the RENs of all devices does not exceed 5. The REN for this terminal equipment is 1.0. Japan modem statements If the computer does not have the Japanese certification mark on the bottom of the computer, refer to the appropriate certification marking below. The Japanese certification mark for the V.92 56K Data/Fax Modem is below:

New Zealand modem statements The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services. This equipment is not capable, under all operating conditions, of correct operation at the higher speeds for which it is designed. Telecom will accept no responsibility should difficulties arise in such circumstances. If this device is equipped with pulse dialing, note that there is no guarantee that Telecom lines will always continue to support pulse dialing. Use of pulse dialing, when this equipment is connected to the same line as other equipment, may give rise to bell tinkle or noise and may also cause a false answer condition. Should such problems occur, the user should not contact the Telecom Faults Service. Some parameters required for compliance with Telecom's Telepermit requirements are dependent on the equipment (PC) associated with this device. The associated equipment shall be set to operate within the following limits for compliance with Telecom's Specifications:

a. b. There shall be no more than 10 call attempts to the same number within any 30-minute period for any single manual call initiation. The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next attempt. c. Where automatic calls are made to different numbers, the equipment shall be set to go on-hook for a period of not less than 5 seconds between the end of one attempt and the beginning of the next attempt. d. The equipment shall be set to ensure that calls are answered between 3 and 30 seconds of receipt of ringing (So set between 2 and 10). 12 Chapter 1 Regulatory notices for notebook computers Voice support All persons using this device for recording telephone conversations shall comply with New Zealand law. This requires that at least one party to the conversation is aware that it is being recorded. In addition, the Principles enumerated in the Privacy Act 1993 shall be complied with in respect to the nature of the personal information collected, the purpose for its collection, how it is to be used, and what is disclosed to any other party. This equipment shall not be set to make automatic calls to the Telecom 111' Emergency Service. Power cord notice If you were not provided with a power cord for the computer or for an external power accessory intended for use with the computer, you should purchase a power cord that is approved for use in your country or region. The power cord must be rated for the product and for the voltage and current marked on the product's electrical ratings label. The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product. In addition, the diameter of the wire must be a minimum of 0.75 mm/

18AWG, and the length of the cord must be between 1.0 m (3.2 ft) and 2 m (6.56 ft). If you have questions about the type of power cord to use, contact your authorized service provider. A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it. Particular attention should be paid to the plug, electrical outlet, and the point where the cord exits from the product. Japan power cord notice DC plug of external HP power supply Macrovision Corporation notice This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. Power cord notice 13 2 Regulatory notices for desktops, thin clients and personal workstations Modem notices WARNING! To reduce the risk of fire, electric shock, and injury to persons when using this device, always follow basic safety precautions, including the following:

Do not use this product near waterfor example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Avoid using this product during an electrical storm. There is a remote risk of electric shock from lightning. Do not use this product to report a gas leak while in the vicinity of the leak. Always disconnect the modem cable before opening the equipment enclosure or touching an uninsulated modem cable, jack, or internal component. If this product was not provided with a telephone line cord, use only No. 26 AWG or larger telecommunication line cord. Do not plug a modem or telephone cable into the RJ-45 (Ethernet network) jack. SAVE THESE INSTRUCTIONS. Telecommunications device approvals The telecommunications device in the computer is approved for connection to the telephone network in the countries and regions whose approval markings are indicated on the product label located on the bottom of the computer or on the modem. Refer to the user guide included with the product to ensure that the product is configured for the country or region in which the product is located. Selecting a country or region other than the one in which it is located may cause the modem to be configured in a way that violates the telecommunication regulations/laws of that country or region. In addition, the modem may not function properly if the correct country or region selection is not made. If, when you select a country or region, a message appears that states that the country or region is not supported, this means that the modem has not been approved for use in this country or region and thus should not be used. U.S. modem statements This equipment complies with Part 68 of the FCC Rules and the requirements adopted by the ACTA. On the bottom of the computer or on the modem is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. Provide this information to the telephone company if you are requested to do so. Applicable certification jack USOC = RJ11C. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. 14 Chapter 2 Regulatory notices for desktops, thin clients and personal workstations The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all locations, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. If this HP equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But, if advance notice isn't practical, the telephone company will notify you as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes to its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted telephone service. If trouble is experienced with this equipment, call technical support. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. You should perform repairs only to the equipment specifically discussed in the Troubleshooting section of the user guide, if one is provided. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission, or corporation commission for information. If your home has specially wired alarm equipment connected to the telephone line, ensure that the installation of this HP equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including a fax machine, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page, or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity, or other individual sending the message, and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-

distance transmission charges). In order to program this information into your fax machine, you should complete the steps outlined in the faxing software instructions. Canadian modem statements This equipment meets the applicable Industry Canada technical specifications. The Ringer Equivalence Number, REN, is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices, subject only to the requirement that the sum of the RENs of all devices does not exceed 5. The REN for this terminal equipment is 1.0. Japanese modem statements If the computer does not have the Japanese certification mark on the bottom of the computer, refer to the appropriate certification marking below. The Japanese certification mark for the LSI Corporation PCI-SV92EX Soft modem is below:

Modem notices 15 New Zealand modem statements The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services. This equipment is not capable, under all operating conditions, of correct operation at the higher speeds for which it is designed. Telecom will accept no responsibility should difficulties arise in such circumstances. If this device is equipped with pulse dialing, note that there is no guarantee that Telecom lines will always continue to support pulse dialing. Use of pulse dialing, when this equipment is connected to the same line as other equipment, may give rise to bell tinkle or noise and may also cause a false answer condition. Should such problems occur, the user should not contact the Telecom Faults Service. Some parameters required for compliance with Telecom's Telepermit requirements are dependent on the equipment (PC) associated with this device. The associated equipment shall be set to operate within the following limits for compliance with Telecom's Specifications:

a. b. There shall be no more than 10 call attempts to the same number within any 30-minute period for any single manual call initiation. The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next attempt. c. Where automatic calls are made to different numbers, the equipment shall be set to go on-hook for a period of not less than 5 seconds between the end of one attempt and the beginning of the next attempt. d. The equipment shall be set to ensure that calls are answered between 3 and 30 seconds of receipt of ringing (So set between 2 and 10). Voice support All persons using this device for recording telephone conversations shall comply with New Zealand law. This requires that at least one party to the conversation is aware that it is being recorded. In addition, the Principles enumerated in the Privacy Act 1993 shall be complied with in respect to the nature of the personal information collected, the purpose for its collection, how it is to be used, and what is disclosed to any other party. This equipment shall not be set to make automatic calls to the Telecom 111' Emergency Service. Electromagnetic compatibility notices This guide provides country- and region-specific nonwireless and wireless regulatory notices and compliance information for the computer product. Some of these notices may not apply to your product. One or more integrated wireless devices may be installed. In some environments, the use of wireless devices may be restricted. Such restrictions may apply onboard airplanes, in hospitals, near explosives, in hazardous 16 Chapter 2 Regulatory notices for desktops, thin clients and personal workstations locations, and so on. If you are uncertain of the policy that applies to the use of this product, ask for authorization to use it before you turn it on. Federal Communications Commission notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio or television technician for help. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user's authority to operate the equipment. Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations. Declaration of conformity for products marked with the FCC logo (United States only) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. 2. This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. For questions regarding the product, contact:

Hewlett-Packard Company P.O. Box 692000, Mail Stop 530113 Houston, Texas 77269-2000 For questions regarding this FCC declaration, contact:

Hewlett-Packard Company P.O. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000 Or, call (281) 514-3333. To identify this product, refer to the part, series, or model number found on the product. Products with wireless LAN devices This product may be equipped with a wireless LAN device. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Electromagnetic compatibility notices 17 WARNING! Exposure to Radio Frequency Radiation The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact is minimized during normal operation. During normal operation: To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antennae should not be less than 20 cm (8 inches). To identify the location of the wireless antennae, refer to the documentation included with the computer. CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15- to 5.25-GHz frequency range. The FCC requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to cochannel mobile satellite systems. High-power radar is allocated as the primary user of the 5.25- to 5.35-GHz and 5.65- to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device. Australia telecom statement The computer must be connected to the Telecommunication Network through a line cord that meets the requirements of AS/CA S008. WARNING! Modems without integral RJ11 connector that are shipped with this computer should not be installed in any other device. This equipment incorporates a radio transmitting and receiving device. In normal use, a separation distance of 20 cm ensures that radio frequency exposure levels comply with the Australian and New Zealand Standards. 18 Chapter 2 Regulatory notices for desktops, thin clients and personal workstations Brazil notice Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio. CAUTION: A alimentao de energia predefinida para 220/230Vv. Se voc possuir tomada eltrica de 110/115Vv, por favor, altere a chave na parte traseira do seu computador para a tenso correta. Canadian notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations, CAN ICES-3(B)/NMB-3(B). If this device has WLAN or Bluetooth capability, this device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. WARNING! Exposure to Radio Frequency Radiation The radiated output power of this device is below the Industry Canada radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact is minimized during normal operation. During normal operation: To avoid the possibility of exceeding the Industry Canada radio frequency exposure limits, human proximity to the antennae should not be less than 20 cm (8 inches). To identify the location of the wireless antennae, refer to the documentation included with the computer. CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15- to 5.25-GHz frequency range. Industry Canada requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-

channel mobile satellite systems. High-power radar is allocated as the primary user of the 5.25- to 5.35-GHz and 5.65- to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device. The antenna for this device is not replaceable. Any attempt at user modification may damage your computer. European Union regulatory notices Declaration of Conformity Products bearing the CE marking comply with one or more of the following EU Directives as may be applicable:

Low Voltage Directive 2006/95/EC; EMC Directive 2004/108/EC; Ecodesign Directive 2009/125/EC; R&TTE Directive 1999/5/EC; RoHS Directive 2011/65/EU Compliance with these directives is assessed using applicable European Harmonised Standards. The full Declaration of Conformity can be found at the following web site: www.hp.eu/certificates (Search with the product model name or its Regulatory Model Number (RMN), which may be found on the regulatory label.) The point of contact for regulatory matters is Hewlett-Packard GmbH, Dept./MS:HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, GERMANY. Products with wireless functionality (EMF) This product meets international guidelines (ICNIRP) for exposure to radio frequency radiation. Electromagnetic compatibility notices 19 This product may incorporate a radio transmitting and receiving device. For desktop computers in normal use, a separation distance of 20 cm ensures that radio frequency exposure levels comply with EU requirements. Restrictions for product with wireless functionality This product is designed for use without restrictions in all EU countries, plus Iceland, Liechtenstein, Norway, and Switzerland. European telephone network declaration (Modem/Fax) The product herewith complies with the requirements of the R&TTE Directive 1999/5/EC (Annex II) and carries the CE marking accordingly. However, due to differences between the individual PSTNs provided in different countries/regions, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems, you should contact your equipment supplier in the first instance. This equipment has been designed to work with analogue DTMF Networks. This equipment may have internetworking difficulties in PSTN networks that only support Pulse Dialing. Please consult with your network operator for further assistance. Ergonomics notice Germany (English text) A computer system comprising HP brand products meets the applicable German ergonomic requirements if all affected constituent products bear the "GS" approval mark, for example Business Desktop PC, keyboard, PC-mouse and monitor. Germany (Deutscher text) Ein aus HP Produkten bestehendes Computersystem erfllt die anwendbaren ergonomischen Anforderungen, wenn alle verwendeten Komponenten das GS Zeichen tragen, wie z. B. Business Desktop PC, Tastatur, PC-Maus und Bildschirm. Japan notice B VCCI-B Wireless LAN and Bluetooth certification markings If this device contains radio equipment, it is certified radio equipment. South Korea notices B ( ) 20 Chapter 2 Regulatory notices for desktops, thin clients and personal workstations

(B) ,

.

(

). 20cm . This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and personnel. Mexico notice Declaracin para Mxico La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. If your product is provided with wireless accessories such as a keyboard or mouse and you need to identify the model of the accessory, refer to the label included on that accessory. Taiwan NCC notices Wireless LAN 802.11a devices Electromagnetic compatibility notices 21 Wireless LAN 802.11 devices/Bluetooth devices/Short range devices 22 Chapter 2 Regulatory notices for desktops, thin clients and personal workstations 3 Safety notices for notebook computers WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper workstation setup, posture, and health and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located on the Web at http://www.hp.com/ergo and on the Documentation CD that is included with the product. Heat-related safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the AC adapter comply with the user-accessible surface temperature limits defined by the International Standard for Safety of Information Technology Equipment (IEC/EN 60950). Potential safety conditions notice If you notice any of the following conditions (or if you have other safety concerns), do not use the computer:

crackling, hissing, or popping sound, or a strong odor or smoke coming from the computer. It is normal for these conditions to appear when an internal electronic component fails in a safe and controlled manner. However, these conditions may also indicate a potential safety issue. Do not assume it is a safe failure. Turn off the computer, disconnect it from its power source, and contact technical support for assistance. User-replaceable battery notices WARNING! Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. WARNING! To reduce the risk of fire or burns, do not disassemble, crush, or puncture; do not short external contacts; do not dispose of in fire or water. WARNING! Keep the battery away from children. WARNING! To reduce potential safety issues, only the battery provided with the computer, a replacement battery provided by HP, or a compatible battery purchased as an accessory from HP should be used with the computer. Heat-related safety warning notice 23 Headset and earphone volume level notice WARNING!

Listening to music at high volume levels and for extended durations can damage ones hearing. To reduce the risk of hearing damage, lower the volume to a safe, comfortable level and reduce the amount of time listening at high levels. For your own safety, before using headsets or earphones, always reset the volume. Some headphones are louder than other headphones, even if the volume control setting is the same. Changing the default audio or equalizer settings might lead to higher volume and should only be done with caution. For your own safety, headsets or earphones used with this product should comply with the headphone limits in EN 50332-2. If the computer includes a headset or earphones, this combination is in compliance to EN 50332-1. Power cord notices WARNING! To reduce the risk of electric shock or damage to the equipment:

Plug the power cord into an AC outlet that is easily accessible at all times. Disconnect power from the computer by unplugging the power cord from the AC outlet. If provided with a 3-pin attachment plug on the power cord, plug the cord into a grounded (earthed) 3-

pin outlet. Do not disable the power cord grounding pin, for example, by attaching a 2-pin adapter. The grounding pin is an important safety feature. WARNING! To reduce potential safety issues, only the AC adapter provided with the computer, a replacement AC adapter provided by HP, or an AC adapter purchased as an accessory from HP should be used with the computer. Brazil notice Este equipamento deve ser conectado obrigatoriamente em tomada de rede de energia eltrica que possua aterramento (trs pinos), conforme a norma nbr abnt 5410,visando a segurana dos usurios contra choques eltricos. Cleaning the keyboard WARNING! To reduce the risk of electric shock or damage to internal components, do not use a vacuum cleaner attachment to clean the keyboard. A vacuum cleaner can deposit household debris on the keyboard surface. Clean the keyboard regularly to prevent keys from sticking and to remove dust, lint, and particles that can become trapped beneath the keys. A can of compressed air with a straw extension can be used to blow air around and under the keys to loosen and remove debris. Travel notice WARNING! To reduce the risk of electric shock, fire, or damage to the equipment, do not attempt to power the computer with a voltage converter kit sold for appliances. 24 Chapter 3 Safety notices for notebook computers China safety notices China: Altitude notice Altitude warning for products not certified for use in >5000 m 2000m or 2000 China: Tropical warning notice Tropical warning for products not certified for use in tropical regions. Norway and Sweden: Cable grounding notice for products with a TV tuner CAUTION: To reduce potential safety issues, use a galvanic isolator when connecting to a cable distribution system. Taiwan BSMI notice BSMI 1. 30 10 2. 2 2 1 China safety notices 25 4 Safety notices for desktops, thin clients and personal workstations Important safety information WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper workstation setup, posture, and health and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located on the Web at http://www.hp.com/ergo and on the Documentation CD that is included with the product. To reduce the risk of electric shock or damage to the equipment:

Plug the power cord into an AC outlet that is easily accessible at all times. Disconnect power from the computer by unplugging the power cord from the AC outlet. If provided with a 3-pin attachment plug on the power cord, plug the cord into a grounded (earthed) 3-

pin outlet. Do not disable the power cord grounding pin, for example, by attaching a 2-pin adapter. The grounding pin is an important safety feature. The computer may be heavy; be sure to use ergonomically correct lifting procedures when moving it. Install the computer near an AC outlet. The AC power cord is your computers main AC disconnecting device and must be easily accessible at all times. For your safety, the power cord provided with your computer has a grounded plug. Always use the power cord with a properly grounded wall outlet, to avoid the risk of electrical shock. To reduce the possibility of an electric shock from the telephone network, plug your computer into the AC outlet before connecting it to the telephone line. Also, disconnect the telephone line before unplugging your computer from the AC power outlet. Always disconnect the modem cord from the telephone system before installing or removing your computer cover. Do not operate the computer with the cover removed. For your safety, always unplug the computer from its power source and from any telecommunications systems (such as telephone lines), networks, or modems before performing any service procedures. Failure to do so may result in personal injury or equipment damage. Hazardous voltage levels are inside the power supply and modem of this product. If your computer is provided with a voltage select switch for use in a 115 or 230 V power system, CAUTION:

the voltage select switch has been pre-set to the correct voltage setting for use in the particular country/

region where it was initially sold. Changing the voltage select switch to the incorrect position can damage your computer and void any implied warranty. This product has not been evaluated for connection to an IT power system (an AC distribution system with no direct connection to earth, according to IEC/EN 60950). Installation conditions See installation instructions before connecting this equipment to the input supply. 26 Chapter 4 Safety notices for desktops, thin clients and personal workstations WARNING! The equipment must be provided with a proper AC protective earth (PE) ground connection. Energized and moving parts may be inside the computer. Disconnect power to the equipment before removing the enclosure. Replace and secure the enclosure before re-energizing the equipment. Battery replacement notice WARNING! The product may contain an internal lithium manganese dioxide, vanadium pentoxide, or alkaline battery or battery pack. There is risk of fire and burns if the battery pack is not handled properly. To reduce the risk of personal injury:

Do not attempt to recharge the battery. Do not expose to temperatures higher than 60 C (140 F). Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Replace only with the HP spare designated for this product. For information about removing a battery, refer to your computer documentation. Batteries, battery packs, and accumulators should not be disposed of together with the general household waste. In order to forward them to recycling or proper disposal, please use the public collection system or return them to HP, an authorized HP partner, or their agents. The Taiwan EPA requires dry battery manufacturing or importing firms, in accordance with Article 15 of the Waste Disposal Act, to indicate the recovery marks on the batteries used in sales, giveaways, or promotions. Contact a qualified Taiwanese recycler for proper battery disposal. Headset and earphone volume level notice WARNING!

Listening to music at high volume levels and for extended durations can damage ones hearing. To reduce the risk of hearing damage, lower the volume to a safe, comfortable level and reduce the amount of time listening at high levels. For your own safety, before using headsets or earphones, always reset the volume. Some headphones are louder than other headphones, even if the volume control setting is the same. Changing the default audio or equalizer settings might lead to higher volume and should only be done with caution. If the computer includes a headset or earphones and bears the "GS" mark, this combination is in compliance with EN 50332-1. For your own safety, headsets or earphones used with these products should comply with the headphone limits in EN 50332-2. Battery replacement notice 27 Laser safety For products equipped with optical drives or fiber optic transceivers. This product may be provided with an optical storage device (i.e., CD or DVD drive) and/or fiber optic transceiver. These contain lasers and are classified as Class 1 Laser Products in accordance with the standard IEC/EN 60825-1 and comply with its requirements. Each laser product complies with US FDA Regulations of 21 CFR 1040.10 and 1040.11 or complies with those regulations except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. WARNING! Use of controls or adjustments or performance of procedures other than those specified herein or in the laser products installation guide may result in hazardous radiation exposure. To reduce the risk of exposure to hazardous radiation:

Do not try to open the module enclosure. There are no user-serviceable components inside. Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein. Allow only HP Authorized Service technicians to repair the unit. Power supply and power cord set requirements Power supply class I grounding requirements For protection from fault currents, the equipment shall be connected to a grounding terminal. Plug the system power cord into an AC outlet that provides a ground connection. Substitute cords may not provide adequate fault protection. Only use the power cord supplied with this product or a Hewlett-Packard authorized replacement. Brazil notice Este equipamento deve ser conectado obrigatoriamente em tomada de rede de energia eltrica que possua aterramento (trs pinos), conforme a norma nbr abnt 5410,visando a segurana dos usurios contra choques eltricos. Denmark Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver forbindelse til stikproppens jord. Finland Norway Sweden Laite on liitettv suojakoskettimilla varustettuun pistorasiaan. Apparatet m tilkoples jordet stikkontakt. Apparaten skall anslutas till jordat uttag. Power supply requirements The power supplies on some products have external power switches. The voltage select switch feature on the product permits it to operate from any line voltage between 100-127 or 200-240 volts AC. Power supplies on 28 Chapter 4 Safety notices for desktops, thin clients and personal workstations those products that do not have external power switches are equipped with internal circuits that sense the incoming voltage and automatically switch to the proper voltage. For safety reasons, use only the AC adapter provided with the unit or an authorized replacement adapter from Hewlett-Packard. Replacement part numbers may be found at http://www.hp.com/cgi-bin/hpsupport/

index.pl. For use in Norway This product is also designed for an IT power system with phase-to-phase voltage 230V. Power cord set requirements The power cord set received with the product meets the requirements for use in the country where the equipment was originally purchased. Use only the power cord provided with the unit or an authorized replacement power cord from Hewlett-Packard or an approved HP source. Replacement part numbers may be found at http://www.hp.com/cgi-bin/hpsupport/index.pl. Power cord sets for use in other countries must meet the requirements of the country where you use the product. For more information on power cord set requirements, contact your authorized HP dealer, reseller, or service provider. WARNING! Do not use power cords from other products. Mismatched power cords may result in a shock and fire hazard. The requirements listed below are applicable to all countries:

1. 2. The power cord must be approved by an acceptable accredited agency responsible for evaluation in the country where the power cord set will be installed. The length of the power cord must be between 1.8 m (6 feet) and 3.6 m (12 feet). For a power cord 2.0 m (6.56 feet) or less, the diameter of the wire must be a minimum of 0.75 mm2 or 18AWG. If the power cord is longer than 2.0 m (6.56 feet), the diameter of the wire must be a minimum of 1.0 mm2 or 16AWG. The power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it. Particular attention should be paid to the plug, electrical outlet, and the point where the cord exits from the product. WARNING! Do not operate this product with a damaged power cord set. If the power cord set is damaged in any manner, replace it immediately. Damaged cords may result in user exposure to hazards. Japan power cord requirements For use in Japan, use only the power cord received with this product. CAUTION: Do not use the power cord received with this product on any other products. Pinch hazard WARNING! Observe pinch hazard areas. Keep fingers away from closing parts. Pinch hazard 29 TV antenna connectors protection External television antenna grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is electrically grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper electrical grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-

discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. Lightning protection For added protection of any product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug the product from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product from lightning and power line surges. Table 4-1 Antenna Grounding Reference Grounding Component 1 2 3 4 5 6 7 Electric Service Equipment Power Service Grounding Electrode System (NEC Art 250, Part III) Ground Clamps Grounding Conductors (NEC Section 810.21) Antenna Discharge Unit (NEC Section 810.20) Ground Clamp Antenna Lead-in Wire Note to CATV system installer This reminder is provided to call the CATV systems installers attention to section 820.93 of the National Electric Code, which provides guidelines for proper grounding and in particular, specify that the Coaxial cable 30 Chapter 4 Safety notices for desktops, thin clients and personal workstations shield shall be connected to grounding system of the building, as close to the point of cable entry as practical. China safety notices China: Altitude notice Altitude warning for products not certified for use in >5000 m 2000m or 2000 China: Tropical warning notice Tropical warning for products not certified for use in tropical regions. China safety notices 31 Germany acoustics notice Sound pressure level (LpA) is far below 70dB(A) (operator position, normal operation, according to ISO 7779) Product noise emission data can be found in the product related IT ECO Declarations at Internet address:

http://www.hp.com/go/ted Schalldruckpegel (LpA) ist weit unterhalb 70 dB(A) (Benutzerposition, normaler Betrieb, nach ISO 7779) Die Schallemissionswerte der Produkte knnen in den produktbezogenen IT ECO Declarations auf folgender Internet Adresse gefunden werden: http://www.hp.com/go/ted Taiwan BSMI notice BSMI 1. 30 10 2. 2 2 1 32 Chapter 4 Safety notices for desktops, thin clients and personal workstations 5 Environmental notices for notebook computers This chapter provides country- and region-specific environmental notices and compliance information. Some of these notices may not apply to your product. Electronic hardware, packaging and battery recycling HP encourages customers to recycle used electronic hardware, HP original print cartridges packaging, and rechargeable batteries. For more information about recycling programs, go to http://www.hp.com/recycle. For information about recycling the product in Japan, refer to http://www.hp.com/jp/hardwarerecycle/. Disposal of waste equipment by users This symbol means do not dispose of your product with your other household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment. For more information, please contact your household waste disposal service or go to http://www.hp.com/recycle. Brazil alkaline battery disposal HEWLETT PACKARD BRASIL LTDA (HP) AV. JOS LUIZ MAZALI N 360 - GALPO B-PARTE 1-BAIRRO RESIDENCIAL BURCK - LOUVEIRA/SP - CEP: 13290-000 CNPJ: 61.797.924/0007-40 Centro de Informaes HP: (11) 4004-7751 ou 0800-7097751 No descarte o produto eletrnico em lixo comum Este produto eletroeletrnico e seus componentes no devem ser descartados no lixo comum, pois embora estejam em conformidade com padres mundiais de restrio a substncias nocivas, podem conter, ainda que em quantidades mnimas, substncias impactantes ao meio ambiente. Ao final da vida til deste produto, o usurio dever entreg-lo HP. A no observncia dessa orientao sujeitar o infrator s sanes previstas em lei. Aps o uso, as pilhas e/ou baterias dos produtos HP devero ser entregues ao estabelecimento comercial ou rede de assistncia tcnica autorizada pela HP. Para maiores informaes , inclusive sobre os pontos de recebimento, acesse: http://www.hp.com.br/reciclar Electronic hardware, packaging and battery recycling 33 Brazil hardware recycling information HEWLETT PACKARD BRASIL LTDA (HP) AV. JOS LUIZ MAZALI N 360 - GALPO B-PARTE 1-BAIRRO RESIDENCIAL BURCK - LOUVEIRA/SP - CEP: 13290-000 CNPJ: 61.797.924/0007-40 Centro de Informaes HP: (11) 4004-7751 ou 0800-7097751 No descarte o produto eletrnico em lixo comum Este produto eletroeletrnico e seus componentes no devem ser descartados no lixo comum, pois embora estejam em conformidade com padres mundiais de restrio a substncias nocivas, podem conter, ainda que em quantidades mnimas, substncias impactantes ao meio ambiente. Ao final da vida til deste produto, o usurio dever entreg-lo HP. A no observncia dessa orientao sujeitar o infrator s sanes previstas em lei. Aps o uso, as pilhas e/ou baterias dos produtos HP devero ser entregues ao estabelecimento comercial ou rede de assistncia tcnica autorizada pela HP. Para maiores informaes , inclusive sobre os pontos de recebimento, acesse: http://www.hp.com.br/reciclar ENERGY STAR Certification (select models only) ENERGY STAR is a U.S. Environmental Protection Agency voluntary program that helps businesses and individuals save money and protect our climate through superior energy efficiency. Products that earn the ENERGY STAR prevent greenhouse gas emissions by meeting strict energy efficiency criteria or requirements set by the U.S. Environmental Protection Agency. As an ENERGY STAR Partner, Hewlett-Packard Company has followed the U.S. EPAs enhanced product certification process to ensure that products marked with the ENERGY STAR logo are ENERGY STAR certified per the applicable ENERGY STAR guidelines. The following logo appears on all ENERGY STAR-certified computers::

A key ENERGY STAR requirement for computer products is power management features that significantly reduce energy consumption when the product is not in use. Power management allows a computer to automatically enter a low power sleep mode, or other low power mode, after a defined period of inactivity. The power management features have been preset as follows when the computer is operating on AC power:

Computer type Time to activate display sleep mode Time to activate computer sleep mode (minutes) Resuming from sleep mode Notebooks, Mobile Workstations Less than or equal to 15 minutes (varies by model) Less than or equal to 30 minutes (varies by model) Product will exit sleep mode when the power/sleep button is pressed. If Wake-on-Lan (WOL) is enabled, the system can resume from sleep in response to a network signal. Tablets/Slates Less than or equal to 1 minute Not applicable Not applicable For computers that support an always-on, always-connected use profile where internet access is available

(such as tablets and slates), alternative low power modes - such as Short or Long Idle modes (as defined in the ENERGY STAR Computer Program Requirements) are provided that consume very little power (</= 10 34 Chapter 5 Environmental notices for notebook computers Watts) and when applicable, maximize product battery life. These alternative low power modes are dynamic, with the display sleep mode activated within 1 minute of user inactivity. The computer exits Sleep when the power/Sleep button is pressed. When the Wake On LAN (WOL) feature is enabled, the computer can also exit Sleep in response to a network signal. Additional information on the potential energy and financial savings of the power management feature can be found on the EPA ENERGY STAR Power Management Web site at http://www.energystar.gov/

powermanagement. Additional information on the ENERGY STAR program and its environmental benefits are available on the EPA ENERGY STAR Web site at http://www.energystar.gov. ENERGY STAR and the ENERGY STAR mark are registered trademarks owned by the U.S. Environmental Protection Agency. Chemical substances HP is committed to providing our customers with information about the chemical substances in our products as needed to comply with legal requirements such as REACH (Regulation EC No 1907/2006 of the European Parliament and the Council). A chemical information report for this product can be found at http://www.hp.com/go/reach. China environmental notices http://www.hp.com/hpinfo/globalcitizenship/environment/productdata/chinasepa.html http://www.hp.com.cn/hardwarerecycle

:

(, ) ,,,

,,,, (http://

www.sepa.gov.cn), 3

:

China PC energy label In accordance with The Regulation of the Implementation on China Energy Label for Microcomputers

(CEL-30), this microcomputer has an Energy Efficiency Label. The energy efficiency grade, TEC (Typical Energy Consumption), and product category presented on the label are determined and calculated according to the standard GB28380-2012. Chemical substances 35 1. Energy Efficiency Grades The grade is determined by the standard with the calculation of base consumption level with the sum of all the allowances for additional components such as main memory and graphics card. For products of any grade, the TEC should not exceed the value specified in the following table:

Product Type Grade 1 Grade 2 Grade 3 TEC (kilowatt hour) Desktop microcomputer, AIO Category A 98.0+Efa 148.0+Efa 198.0+Efa Portable Computer Category B Category C Category D Category A Category B Category C 125.0+Efa 159.0+Efa 184.0+Efa 20.0+Efa 26.0+Efa 54.5+Efa 175.0+Efa 225.0+Efa 209.0+Efa 259.0+Efa 234.0+Efa 284.0+Efa 35.0+Efa 45.0+Efa 75.0+Efa 45.0+Efa 65.0+Efa 123.5+Efa NOTE: Efa is the sum of power factor of product additional functions. 2. Typical Energy Consumption The energy consumption figure presented on the label is the data measured with the representative configuration that covers all the configurations in the registration unit which is selected according to CEL-30. Thus, actual energy consumption of this specific microcomputer may not be the same as the TEC data presented in the label. 3. Product Category The product category is determined by the standard according to the microcomputers configuration. The categorization of products complies with the regulations in the following table:

Product Type Category A Category B Category C Configuration Description Desktop microcomputer, AIO Portable Computer The desktop microcomputer and AIO whose configuration is out of the scope of Category B, C, and D The portable computer whose configuration is out of the scope of Category B and C CPU physical core number of 2, and system memory of not less than 2GB A Discrete GPU CPU physical core number of over 2, with at least one of the following features:

1. 2. System memory of not less than 2 GB A Discrete GPU The product that has a CPU physical core number of not less than 2, system memory of not less than 2GB, A Discrete GPU with Frame Buffer Width not less than 128-bit. Category D CPU physical core number of not less than 4, with at least one of the following features:

1. 2. System memory of not less than 4 GB A Discrete GPU with Frame Buffer Width not less than 128-bit 36 Chapter 5 Environmental notices for notebook computers For more details on the specification, please refer to the standard GB28380-2012. CEL30 GB28380 2012:

1.

() A B C D A B C 1 2 3 98.0+Efa 148.0+Efa 198.0+Efa 125.0+Efa 175.0+Efa 225.0+Efa 159.0+Efa 209.0+Efa 259.0+Efa 184.0+Efa 234.0+Efa 284.0+Efa 20.0+Efa 35.0+Efa 45.0+Efa 26.0+Efa 45.0+Efa 65.0+Efa 54.5+Efa 75.0+Efa 123.5+Efa Efa 2. 3. A B C D B C D CPU 2 2GB CPU 2 a. a 2GB b. GPU) B C GPU CPU 2 2GB GPU 128

. CPU 4 a. 4GB b. GPU 128 China PC energy label 37 GB28380-2012 China restriction of hazardous substances (RoHS) The Table of Hazardous Substances/Elements and their Content As required by China's Management Methods for Controlling Pollution by Electronic Information Products Hazardous Substances and Elements Part Name Lead (Pb) Mercury

(Hg) Cadmium

(Cd) Hexavalent Chromium

(Cr(VI)) Polybrominated biphenyls (PBB) Polybrominated diphenyl ethers

(PBDE) Battery Cables Camera Chassis/Other Flash memory card reader Floppy disk drive Hard disk drive Headphones I/O PCAs Keyboard Liquid crystal display

(LCD) panel Media (CD/DVD/floppy) Memory Motherboard, processor, heat sinks Mouse Optical disk drive Optional docking device Power adapter Power supply Remote control Smart card/Java card reader Speakers, external TV tuner X X X X X X X X X X X O X X X X X X X X X X X O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O 38 Chapter 5 Environmental notices for notebook computers Hazardous Substances and Elements Part Name Lead (Pb) USB flash memory drive USB hub Web camera Wireless receiver Wireless cards X X X X X Mercury

(Hg) Cadmium

(Cd) Hexavalent Chromium

(Cr(VI)) Polybrominated biphenyls (PBB) Polybrominated diphenyl ethers

(PBDE) O O O O O O O O O O O O O O O O O O O O O O O O O This form has been prepared in compliance with the provisions of SJ/T 11364. O: Indicates that the content of said hazardous substance in all of the homogenous materials in the component is within the limits required by GB/T 26572. X: Indicates that the content of said hazardous substance exceeds the limits required by GB/T 26572 in at least one homogenous material in the component. All parts named in this table with an X are in compliance with the European Unions RoHS Legislation. NOTE: The referenced Environmental Protection Use Period Marking was determined according to normal operating use conditions of the product such as temperature and humidity.

/

I/O PCA

(LCD) CD/DVD/

(Pb)

(Hg)

(Cd)

(Cr(VI)) (PBB)

(PBDE) X X X X X X X X X X X O X X O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O China restriction of hazardous substances (RoHS) 39

/Java USB USB

(Pb)

(Hg)

(Cd)

(Cr(VI)) (PBB)

(PBDE) X X X X X X X X X X X X X X O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O SJ/T 11364 O: GB/T 26572 X GB/T 26572 X RoHS

:

40 Chapter 5 Environmental notices for notebook computers India restriction of hazardous substances (RoHS) This product complies with the India E-waste (Management and Handling) Rule 2011 and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule. Japan restriction of hazardous substances (RoHS) 2008 JISC0950 2006 7 http://www.hp.com/go/jisc0950 A Japanese regulatory requirement, defined by specification JIS C 0950, 2008, mandates that manufacturers provide Material Content Declarations for certain categories of electronic products offered for sale after July 1, 2006. To view the JIS C 0950 material declaration for this product, visit http://www.hp.com/go/jisc0950. Mexico Sustainable Energy Use Law This product has been labeled in compliance with the Mexico Sustainable Energy Use Law requiring disclosure of power consumption in the normal use (idle mode) and standby modes. Your product is one of many configurations in this model family; the idle mode power consumption of your specific configuration may vary from the information on the label. Actual power consumption of your product may be higher or lower than the value reported on the Mexico product energy label due to factors such as configuration

(components and modules chosen) and usage (tasks being performed, software installed and running, etc.). Turkey EEE regulation Trkiye Cumhuriyeti: EEE Ynetmeliine Uygundur Ukraine restriction of hazardous substances (RoHS) The equipment complies with requirements of the Technical Regulation, approved by the Resolution of Cabinet of Ministry of Ukraine as of December 3, 2008 1057, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment.

, 3 2008 1057. Perchlorate materialspecial handling may apply See http://www.dtsc.ca.gov/hazardouswaste/perchlorate. This products real-time clock battery or coin cell battery may contain perchlorate and may require special handling when recycled or disposed of in California. India restriction of hazardous substances (RoHS) 41 6 Environmental notices for desktops, thin clients and personal workstations This chapter provides country- and region-specific environmental notices and compliance information. Some of these notices may not apply to your product. Electronic hardware, packaging and battery recycling HP encourages customers to recycle used electronic hardware, HP original print cartridges packaging, and rechargeable batteries. For more information about recycling programs, go to http://www.hp.com/recycle. For information about recycling the product in Japan, refer to http://www.hp.com/jp/hardwarerecycle/. Disposal of waste equipment by users This symbol means do not dispose of your product with your other household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment. For more information, please contact your household waste disposal service or go to http://www.hp.com/recycle. Brazil alkaline battery disposal HEWLETT PACKARD BRASIL LTDA (HP) AV. JOS LUIZ MAZALI N 360 - GALPO B-PARTE 1-BAIRRO RESIDENCIAL BURCK - LOUVEIRA/SP - CEP: 13290-000 CNPJ: 61.797.924/0007-40 Centro de Informaes HP: (11) 4004-7751 ou 0800-7097751 No descarte o produto eletrnico em lixo comum Este produto eletroeletrnico e seus componentes no devem ser descartados no lixo comum, pois embora estejam em conformidade com padres mundiais de restrio a substncias nocivas, podem conter, ainda que em quantidades mnimas, substncias impactantes ao meio ambiente. Ao final da vida til deste produto, o usurio dever entreg-lo HP. A no observncia dessa orientao sujeitar o infrator s sanes previstas em lei. Aps o uso, as pilhas e/ou baterias dos produtos HP devero ser entregues ao estabelecimento comercial ou rede de assistncia tcnica autorizada pela HP. Para maiores informaes , inclusive sobre os pontos de recebimento, acesse: http://www.hp.com.br/reciclar 42 Chapter 6 Environmental notices for desktops, thin clients and personal workstations Brazil hardware recycling information HEWLETT PACKARD BRASIL LTDA (HP) AV. JOS LUIZ MAZALI N 360 - GALPO B-PARTE 1-BAIRRO RESIDENCIAL BURCK - LOUVEIRA/SP - CEP: 13290-000 CNPJ: 61.797.924/0007-40 Centro de Informaes HP: (11) 4004-7751 ou 0800-7097751 No descarte o produto eletrnico em lixo comum Este produto eletroeletrnico e seus componentes no devem ser descartados no lixo comum, pois embora estejam em conformidade com padres mundiais de restrio a substncias nocivas, podem conter, ainda que em quantidades mnimas, substncias impactantes ao meio ambiente. Ao final da vida til deste produto, o usurio dever entreg-lo HP. A no observncia dessa orientao sujeitar o infrator s sanes previstas em lei. Aps o uso, as pilhas e/ou baterias dos produtos HP devero ser entregues ao estabelecimento comercial ou rede de assistncia tcnica autorizada pela HP. Para maiores informaes , inclusive sobre os pontos de recebimento, acesse: http://www.hp.com.br/reciclar ENERGY STAR Certification (select models only) ENERGY STAR is a U.S. Environmental Protection Agency voluntary program that helps businesses and individuals save money and protect our climate through superior energy efficiency. Products that earn the ENERGY STAR prevent greenhouse gas emissions by meeting strict energy efficiency criteria or requirements set by the U.S. Environmental Protection Agency. As an ENERGY STAR Partner, Hewlett-Packard Company has followed the U.S. EPAs enhanced product certification process to ensure that products marked with the ENERGY STAR logo are ENERGY STAR certified per the applicable ENERGY STAR guidelines. The following logo appears on all ENERGY STAR-certified computers::

A key ENERGY STAR requirement for computer products is power management features that significantly reduce energy consumption when the product is not in use. Power management allows a computer to automatically enter a low power sleep mode, or other low power mode, after a defined period of inactivity. The power management features have been preset as follows when the computer is operating on AC power:

Computer type Time to activate display sleep mode Time to activate computer sleep mode (minutes) Resuming from sleep mode Desktops, Integrated Desktops, Workstations Less than or equal to 15 minutes (varies by model) Less than or equal to 30 minutes (varies by model) Thin clients Less than or equal to 15 minutes (varies by model) Less than or equal to 30 minutes when sleep mode is supported by the operating system (varies by model) Product will exit sleep mode when user interacts with any input device, including the mouse or keyboard. If Wake-on-Lan (WOL) is enabled, the system can resume from sleep in response to a network signal. When sleep mode is supported by operating system product will exit sleep mode when user interacts with any input device, including the mouse or keyboard. Brazil hardware recycling information 43 Computer type Time to activate display sleep mode Time to activate computer sleep mode (minutes) Resuming from sleep mode If Wake-on-Lan (WOL) is enabled, the system can resume from sleep in response to a network signal. The computer exits Sleep when the power/Sleep button is pressed. When the Wake On LAN (WOL) feature is enabled, the computer can also exit Sleep in response to a network signal. Additional information on the potential energy and financial savings of the power management feature can be found on the EPA ENERGY STAR Power Management Web site at http://www.energystar.gov/

powermanagement. Additional information on the ENERGY STAR program and its environmental benefits are available on the EPA ENERGY STAR Web site at http://www.energystar.gov. ENERGY STAR and the ENERGY STAR mark are registered trademarks owned by the U.S. Environmental Protection Agency. Chemical substances HP is committed to providing our customers with information about the chemical substances in our products as needed to comply with legal requirements such as REACH (Regulation EC No. 1907/2006 of the European Parliament and the Council). A chemical information report for this product can be found at http://www.hp.com/go/reach. Mercury statement This statement applies to All-in-One computers with built-in display panels that do not use LED backlighting. This HP product may contain the following material that might require special handling at end-of-life:

Mercury in the fluorescent lamp in the display LCD Disposal of mercury can be regulated because of environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance (EIA)

(http://www.eiae.org). Perchlorate materialspecial handling may apply The computers real-time clock battery may contain perchlorate and may require special handling when recycled or disposed of in California. See http://www.dtsc.ca.gov/hazardouswaste/perchlorate/. China environmental notices http://www.hp.com/hpinfo/globalcitizenship/environment/productdata/chinasepa.html 44 Chapter 6 Environmental notices for desktops, thin clients and personal workstations http://www.hp.com.cn/hardwarerecycle

:

(, ) ,,,

,,,, (http://

www.sepa.gov.cn), 3

:

China PC energy label In accordance with The Regulation of the Implementation on China Energy Label for Microcomputers

(CEL-30), this microcomputer has an Energy Efficiency Label. The energy efficiency grade, TEC (Typical Energy Consumption), and product category presented on the label are determined and calculated according to the standard GB28380-2012. 1. Energy Efficiency Grades The grade is determined by the standard with the calculation of base consumption level with the sum of all the allowances for additional components such as main memory and graphics card. For products of any grade, the TEC should not exceed the value specified in the following table:

Product Type Grade 1 Grade 2 Grade 3 TEC (kilowatt hour) Desktop microcomputer, AIO Category A 98.0+Efa 148.0+Efa 198.0+Efa Portable Computer Category B Category C Category D Category A Category B Category C 125.0+Efa 159.0+Efa 184.0+Efa 20.0+Efa 26.0+Efa 54.5+Efa 175.0+Efa 225.0+Efa 209.0+Efa 259.0+Efa 234.0+Efa 284.0+Efa 35.0+Efa 45.0+Efa 75.0+Efa 45.0+Efa 65.0+Efa 123.5+Efa NOTE: Efa is the sum of power factor of product additional functions. 2. Typical Energy Consumption The energy consumption figure presented on the label is the data measured with the representative configuration that covers all the configurations in the registration unit which is selected according to CEL-30. Thus, actual energy consumption of this specific microcomputer may not be the same as the TEC data presented in the label. 3. Product Category The product category is determined by the standard according to the microcomputers configuration. The categorization of products complies with the regulations in the following table:

China PC energy label 45 Product Type Category A Category B Category C Configuration Description Desktop microcomputer, AIO Portable Computer The desktop microcomputer and AIO whose configuration is out of the scope of Category B, C, and D The portable computer whose configuration is out of the scope of Category B and C CPU physical core number of 2, and system memory of not less than 2GB A Discrete GPU CPU physical core number of over 2, with at least one of the following features:

1. 2. System memory of not less than 2 GB A Discrete GPU The product that has a CPU physical core number of not less than 2, system memory of not less than 2GB, A Discrete GPU with Frame Buffer Width not less than 128-bit. Category D CPU physical core number of not less than 4, with at least one of the following features:

1. 2. System memory of not less than 4 GB A Discrete GPU with Frame Buffer Width not less than 128-bit For more details on the specification, please refer to the standard GB28380-2012. CEL30 GB28380 2012:

1.

() A B C D A B C 1 2 3 98.0+Efa 148.0+Efa 198.0+Efa 125.0+Efa 175.0+Efa 225.0+Efa 159.0+Efa 209.0+Efa 259.0+Efa 184.0+Efa 234.0+Efa 284.0+Efa 20.0+Efa 35.0+Efa 45.0+Efa 26.0+Efa 45.0+Efa 65.0+Efa 54.5+Efa 75.0+Efa 123.5+Efa Efa 2. 46 Chapter 6 Environmental notices for desktops, thin clients and personal workstations 3. A B C D B C D CPU 2 2GB CPU 2 a. a 2GB b. GPU) B C GPU CPU 2 2GB GPU 128

. CPU 4 a. 4GB b. GPU 128 GB28380-2012 China PC energy label 47 China restriction of hazardous substances (RoHS) As required by China's Management Methods for Controlling Pollution by Electronic Information Products Hazardous Substances and Elements Part Name Lead

(Pb) Mercury

(Hg) Cadmium

(Cd) Hexavalent Chromium

(Cr(VI)) Polybromi-

nated biphenyls

(PBB) Polybromi-

nated diphenyl ethers (PBDE) Motherboard, processor and heat sink Memory I/O PCAs Power supply Keyboard Mouse Chassis/Other Fans Internal/External Media Reading Devices External Control Devices Cable Hard Disk Drive Display X X X X X X X X X X X X X O O O O O O O O O O O O X O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O This form has been prepared in compliance with the provisions of SJ/T 11364. O: Indicates that the content of said hazardous substance in all of the homogenous materials in the component is within the limits required by GB/T 26572. X: Indicates that the content of said hazardous substance exceeds the limits required by GB/T 26572 in at least one homogenous material in the component. All parts named in this table with an X are in compliance with the European Unions RoHS Legislation. NOTE: The referenced Environmental Protection Use Period Marking was determined according to normal operating use conditions of the product such as temperature and humidity. 48 Chapter 6 Environmental notices for desktops, thin clients and personal workstations The Table of Hazardous Substances/Elements and their Content I/O PCAs

/

/

(Pb)

(Hg)

(Cd)

(Cr(VI))

(PBB)

(PBDE) X X X X X X X X X X X X X O O O O O O O O O O O O X O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O SJ/T 11364 O GB/T 26572 X GB/T 26572 X RoHS China restriction of hazardous substances (RoHS) 49 India restriction of hazardous substances (RoHS) This product complies with the India E-waste (Management and Handling) Rule 2011 and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule. IT ECO declarations Desktop PCs and Thin Clients http://www.hp.com/hpinfo/globalcitizenship/environment/productdata/itecodesktop-pc.html?

jumpid=reg_R1002_USEN Workstations http://www.hp.com/hpinfo/globalcitizenship/environment/productdata/itecoworkstatio.html Japan restriction of hazardous substances (RoHS) 2008 JISC0950 2006 7 http://www.hp.com/go/jisc0950 A Japanese regulatory requirement, defined by specification JIS C 0950, 2008, mandates that manufacturers provide Material Content Declarations for certain categories of electronic products offered for sale after July 1, 2006. To view the JIS C 0950 material declaration for this product, visit http://www.hp.com/go/jisc0950. Ley para el Aprovechamiento Sustentable de la Energa de Mxico (Mexico Sustainable Energy Use Law) Se ha etiquetado este producto en conformidad con la Ley para el Aprovechamiento Sustentable de la Energa de Mxico, que requiere la divulgacin del consumo de energa del modo de uso normal (modo inactivo) y del modo de espera. Su producto es una de las muchas configuraciones de esta familia de modelos; el consumo de energa del modo inactivo de su configuracin especfica puede diferir de la informacin de la etiqueta. El consumo real de energa de su producto puede ser mayor o menor que el valor informado en la etiqueta de energa de producto para Mxico a causa de factores como la configuracin

(componentes y mdulos seleccionados) y el uso (tareas que se estn efectuando, software instalado y en ejecucin, etc.). NOTE: Esta ley no es aplicable a los workstations. This product has been labeled in compliance with the Mexico Sustainable Energy Use Law requiring disclosure of power consumption in the normal use (idle mode) and standby modes. Your product is one of many configurations in this model family; the idle mode power consumption of your specific configuration may vary from the information on the label. Actual power consumption of your product may be higher or lower than the value reported on the Mexico product energy label due to factors such as configuration

(components and modules chosen) and usage (tasks being performed, software installed and running, etc.). NOTE: Workstations are not labeled because the law is not applicable to the workstation product category. 50 Chapter 6 Environmental notices for desktops, thin clients and personal workstations Turkey EEE regulation Trkiye Cumhuriyeti: EEE Ynetmeliine Uygundur

(Ukraine restriction of hazardous substances (RoHS))

, 3 2008 1057. The equipment complies with requirements of the Technical Regulation, approved by the Resolution of Cabinet of Ministry of Ukraine as of December 3, 2008 1057, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment. TCO Certified Edge Certification This section applies only to products bearing the TCO Certified Edge logo. Turkey EEE regulation 51 52 Chapter 6 Environmental notices for desktops, thin clients and personal workstations Index A airline travel notice 8 altitude notice 25, 31 B battery notice 8, 23, 41 battery recycling 33 Brazil notice 3 C cable grounding notice 25 Canada modem statement 12 Canada notices 4 China environmental notices 35, 44 China PC energy label 35, 45 China restriction of hazardous substances notice 38, 48 D Declaration of Conformity notebook computers 3 disposal notices battery 41 battery, user replacement 8 equipment 33 factory sealed battery 8 E electronic hardware and battery recycling 33 ENERGY STAR certification 34, 43 environmental notices 33 equipment disposal notice 33 ergonomics notice 5, 20 European Union notices 4, 19 F Federal Communications Commission desktops, thin clients and workstations notice 17 desktops, thin clients, workstations cables 17 desktops, thin clients, workstations modifications 17 notebook computers cables 2 notebook computers modifications 2 modifications, notebook computers Federal Communications notebook computers notice 2 Commission 2 G GS Notice 5, 20 H headset and earphone volume level notice 24 I India restriction of hazardous substances notice 41, 50 J Japan modem statement 12 Japan notice 6 Japan power cord notice 13 Japan restriction of hazardous substances notice 41, 50 K keyboard notice 24 L labels, regulatory 1 laser safety notice 9 M Macrovision Corporation notice 13 Mexico Sustainable Energy Use Law 41 Mexico wireless notice 6 modem notices 9 modem statements Canada 12 Japan 12 New Zealand 12 U.S. 10 modifications, desktops, thin clients, workstations Federal Communications Commission 17 N New Zealand modem statement 12 notices airline travel 8 battery 8, 41 battery, user replacement 23 Brazil 3 Canada 4 China restriction of hazardous substances 38, 48 environmental 33 equipment disposal 33 ergonomics 5, 20 European Union 4, 19 headset and earphone volume level 24 India restriction of hazardous substances 41, 50 Japan 6 Japan power cord 13 Japan restriction of hazardous substances 41, 50 keyboard 24 laser safety 9 Macrovision Corporation 13 Mexico 6 modem 9 perchlorate material 41 power cords 13, 24 Singapore 7 South Korea 6 Taiwan 7, 21 Thailand WWAN wireless notice 7 travel 24 Ukraine restriction of hazardous substances 41, 51 notices, desktops, thin clients and workstations Federal Communications Commission 17 Index 53 notices, notebook computers Federal Communications Commission 2 P power cord notice 13, 24 R recycling, electronic hardware and battery 33 S Singapore wireless notice 7 South Korea notice 6 T Taiwan notice 7, 21 TCO Certified Edge Certification 51 Thailand WWAN wireless notice 7 travel notice 24 tropical warning notice 25, 31 TV tuner, cable grounding notice 25 U U.S. modem statement 10 Ukraine restriction of hazardous substances notice 41, 51 V voice support 13 volume level notice, headset and earphone 24 W wireless LAN devices 3, 18, 19 54 Index