WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/5750436.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case MerryIoT Motion Detection Reference Manual Model Name: MS10 MS10-915 MS10-868 BQW_02_0033.003 1. Description The Motion Sensor utilizes LoRaWAN connectivity to communicate the presence or not of a person. The intended use is to place the sensor with a good view of a room to determine if there is motion in the room or not. The sensor is composed of a Passive Infrared Detector and Fresnel Lens. The main body contains active electronics to measure movement and transmit any changes to a LoRaWAN network. There are also vibration and tilt detection in case of tampering. Once the event is detected, the sensor will send an uplink. 4. Messages 3. Operation Table of Content 1. Description 2. Specifications 1 2 2.1 Mechanical ....................................................... 2 2.1.1 Sensor ................................................... 2 2.2 Environmental .................................................. 2 2.3 Power ............................................................... 2 2.4 Radio ................................................................ 2 2.5 User Interface .................................................. 2 2.6 Certifications and Conformity .......................... 2 2.7 Additional Features .......................................... 2 3 3.1 Installation Mode ............................................. 3 3.2 Default Operation ............................................ 3 3 4.1 Status ............................................................... 3 4.1.1 Triggers ................................................. 3 4.1.2 Payload .................................................. 4 5 5.1 Replacement .................................................... 5 5.2 Cautions ........................................................... 5 6 6.1 Device back label ............................................. 6 6.1.1 All QR code ............................................ 6 6.1.2 Serial Number ....................................... 7 6.1.3 Model Name ......................................... 7 6.1.4 FCC ID .................................................... 7 6.1.5 IC ID ....................................................... 7 6.1.6 Caution!................................................. 7 6.2 Packaging label................................................. 7 8 9 9 10 11 7. Important Product & Safety Instructions 8. Warnings 9. Notices 10. Cautions 11. Regulatory 6. Label format information 5. Battery 12. Configuration Downlink Command 11.1 Federal Communication Commission Interference Statement ....................................... 11 11.2 Industry Canada statement: ........................ 12 13 12.1 Payload ................................................. 13 12.2 For Sensor Settings ...................................... 15 12.2.1 Payload .............................................. 15 12.2.2 Command Description ...................... 16 12.3 Response Content ........................................ 17 12.4 Frame Count 1 Content ................................ 17 17 13.1 Payload......................................................... 17 13. BLE FOTA Downlink Command BROWAN COMMUNICATIONS All rights reserved 1 2. Specifications 2.1 Mechanical 2.2 Environmental Temperature IP Rating 2.4 Radio Frequency 0C to +50C IP 40 equivalent Either 863-870 MHz for the EU model and 902-
928 MHz for North America Rx Sensitivity (Conducted)
-140dBm Antenna Gain(LoRa) Antenna Gain(BLE) 0.52dBi Peak, -5dBi Avg 2.21dBi Peak 2.6 Certifications and Conformity FCC On-going CE On-going IC TBD 2.1.1 Sensor Length x Width x Height Weight 25mm x 70mm x 70mm 62g without battery 96g with battery Dual Passive Infrared detectors Fresnel Lens with 123 horizontal
& 93 vertical view Tamper detection Temperature/Humidity Maximum detect range 7M 1.5 V AA Alkaline x 2 pcs, 2700 mAh 3.0 V 2.4 V Sensor 2.3 Power Source System Maximum Voltage System Minimum Voltage Operation Current 135mA maximum 2.5 User Interface LEDs Motion Button One blue LED One Motion Sensor Test Button 2.7 Additional Features Battery Monitoring Tamper detection Environment temperature BROWAN COMMUNICATIONS All rights reserved 2 3. Operation 3.1 Installation Mode Users need to press the button over 5 seconds to activate operation into installation mode. When the Sensor tries to join the network, it will keep blinking for 3 seconds. Once the sensor joins the network, the LED will keep on for 3 seconds and send an uplink. Users can press the button for over 5 seconds to try to join the network again. The device will send uplink three times with fw version when the device joined successfully. 3.2 Default Operation While in default operation the device will immediately send a message any time a control signal is transmitted. Free to Occupied Tamper detected Button pressed Keepalive message Users can press the button to send a test message to the network. The device will send a status message every 10 minutes while in the occupied state and every 1 hour while in the vacant state. While in default mode the device will flash the LED 3 times within 100ms only when the user presses the test button. 4. Messages LoRaWAN Packets for this device use port 122. 4.1 Status 4.1.1 Triggers Motion Sensor Triggers:
(1) While in free mode, send a message every 60 minutes;
(2) When the status changes from the free mode to occupied mode, send a message immediately;
(3) While the occupied state continues, send a message every 10 minutes;
(4) When the device isn't triggered by the occupied state again within 5 minutes from the last message, the status changes from occupied to free mode and sends a message. Tamper Trigger:
Immediately send a message Button Pressed Trigger:
Immediately send a message BROWAN COMMUNICATIONS All rights reserved 3 4.1.2 Payload Port Payload Length 122 9 bytes Bytes 0 1 2 Field Status Battery Temp 3 RH 4 5 6 7 8 Time Count Status Sensors status Bit [0]
Bit [1]
Bit [2]
Bits [7:3]
Battery level Bits [3:0]
Battery 1 occupied, 0 free 1 Button pressed, 0 - Button released 1 Tamper detected, 0 - No tamper detected RFU unsigned value , range 0 15;
battery voltage in V = (21 + ) 10. Bits [7:4]
RFU Temp Environment Temperature Bits [7:0]
sign integer temperature in C RH Relative humidity as measured by a digital sensor Bits [6:0]
Bit [7]
unsigned value in %, range 0-100. RFU Time Time elapsed since the last event-triggered Bits [15:0]
unsigned value in minutes, range 0 65,535.
*Note little-endian format. Count Total count of event-triggered Bits [23:0]
unsigned value, range 0 16,777,215.
*Note: little-endian format. Note: This value is not stored persistently on the device, and may reset whenever the device is power-cycled or rebooted. BROWAN COMMUNICATIONS All rights reserved 4 5. Battery 5.1 Replacement Use Alkaline battery (AA) only. Remove the battery cover and replace the batteries.
(cross-slot screwdriver required) 5.2 Cautions CAUTION: Disposal of a battery (or battery pack) into a fire or a hot oven, or mechanically crushing or cutting of a battery
(or battery pack) can result in an EXPLOSION!
Leaving a battery (or battery pack) in an extremely high temperature surrounding environment can result in an EXPLOSION or leakage of flammable liquid or gas. A battery (or battery pack) subjected to extremely low air pressure may also result in an EXPLOSION or leakage of flammable liquid or gas. Discard used batteries according to the manufacturer's instructions. CAUTION: The unit is provided with a battery-powered circuit. There is a danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturers instructions. Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries according to the Instructions. BROWAN COMMUNICATIONS All rights reserved 5 6. Label format information 6.1 Device back label 6.1.1 All QR code URN:LW:D0: 0016160000000001:0016160000XXXXXX:01632002 The total maximum resulting character sentence is 48 alphanumeric characters long. 6.1.1.1 JoinEUI 900MHz: 0016160000000001. (US) 800MHz: 0016160000000002. (EU) Uses a hexadecimal representation resulting in 16 characters. 6.1.1.2 DevEUI 0016160000XXXXXX. Uses a hexadecimal representation resulting in 16 characters 6.1.1.3 ProfileID The profile identifier encodes a Vendor Identifier and a Vendor Profile Identifier as a hexadecimal representation resulting in 8 characters. 6.1.1.3.1 VendorID 0163 VendorID is assigned by the LoRa Alliance. 6.1.1.3.2 VendorProfileID 900MHz: 2002 (US) 800MHz: 3002 (EU) BROWAN COMMUNICATIONS All rights reserved 6 6.1.2 Serial Number SN: MS10915XXXXXX Not including in QR code. 6.1.3 Model Name MODEL: MS10. Fixed code, not including in QR code. 6.1.4 FCC ID 2AAS9MS10 6.1.5 IC ID 26296-MS10 6.1.6 Caution!
For more information please refer to chapter 5.2. and 10. 6.2 Packaging label GS1 DataMatrix The GS1 Application Identifier (21) indicates that the GS1 Application Identifier data field contains a serial number. The GS1 Application Identifier (92) assigned to the companys internal information is DevEUI. BROWAN COMMUNICATIONS All rights reserved 7 7. Important Product & Safety Instructions For the most current and more detailed information about Browan features and settings as well as safety instructions, please download the user manual for the products online at www.browan.com before the use of any Browan products or services. Certain sensors contain magnets. Keep away from ALL Children! Do not put it in your nose or mouth. Swallowed magnets can stick to intestines causing serious injury or death. Seek immediate medical attention if magnets are swallowed. These products are not toys and contain small parts that can be dangerous to children under 3 years old. Do not allow children or pets to play with products. Observe proper precautions when handling batteries. Batteries may leak or explode if improperly handled. Observe the following precautions to avoid a sensor explosion or fire:
Do not drop, disassemble, open, crush, bend, deform, puncture, shred, microwave, incinerate, or paint the sensors, Hub, or other hardware. Do not insert foreign objects into any opening on the sensors or Hub, such as the USB port. Do not use the hardware if it has been damaged for example, if cracked, punctured, or harmed by water. Disassembling or puncturing the battery (whether integrated or removable) can cause an explosion or fire. Do not dry the sensors or battery with an external heat source such as a microwave oven or hairdryer. BROWAN COMMUNICATIONS All rights reserved 8 8. Warnings Do not place naked flame sources, such as lighted candles, on or near the equipment. The battery shall not be exposed to excessive heat such as sunshine, fire, or the like. Do not dismantle, open or shred battery packs or cells. Do not expose batteries to heat or fire. Avoid storage in direct sunlight. Do not short-circuit the battery. Do not store batteries in a box or drawer where they may short-
circuit each other or be short-circuited by other metal objects. Do not remove a battery from its original packaging until required for use. Do not subject batteries to mechanical shock. In the event of a battery leaking, do not allow the liquid to come in contact with the skin or eyes. If a contact has been made, wash the affected area with copious amounts of water, and seek medical advice. Do not use any charger other than that specifically provided for use with the equipment. Observe the plus (+) and minus (-) marks on the battery and equipment and ensure correct use. Do not use any which is not designed for use with the product. Do not mix cells of different manufacture, capacity, size, or type within a device. Keep batteries out of the reach of children. Seek medical advice immediately if a battery has been swallowed. Always purchase the correct battery for the equipment. Keep batteries clean and dry. Wipe the battery terminals with a clean dry cloth if they become dirty. 9. Notices Avoid exposing your sensors or batteries to very cold or very hot temperatures. Low or high-
temperature conditions may temporarily shorten the battery life or cause the sensors to temporarily stop working. Take care in setting up the Hub Gateway and other hardware. Follow all installation instructions in the User Guide. Failure to do so may result in injury. Do not install hardware equipment while standing in water or with wet hands. Failure to do so can result in electric shock or death. Use caution when setting up all electronic equipment. When charging the sensors, do not handle the sensors with wet hands. Failure to observe this precaution could result in electric shock. PROP 65 WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm Cleaning Browan Products: Use a clean dry cloth or wipe to clean Browan products. Do not use detergent or abrasive materials to clean the Browan products, as this may damage the sensors. BROWAN COMMUNICATIONS All rights reserved 9 10. Cautions CAUTION: Disposal of a battery (or battery pack) into a fire or a hot oven, or mechanically crushing or cutting of a battery (or battery pack) can result in an EXPLOSION!
CAUTION: The unit is provided with a battery-powered circuit. Leaving a battery (or battery pack) in an extremely high temperature surrounding environment can result in an EXPLOSION or leakage of flammable liquid or gas. A battery (or battery pack) subjected to extremely low air pressure may also result in an EXPLOSION or leakage of flammable liquid or gas. Discard used batteries according to the manufacturer's instructions. There is a danger of EXPLOSION if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturers instructions. Risk of EXPLOSION if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the Instructions. BROWAN COMMUNICATIONS All rights reserved 10 11. Regulatory Hereby, Browan Communications Inc. declares that the radio equipment for Browan products complies with Directive 2014/53/EU. This device complies with Part 15 of the FCC Rules and RSS Standards of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This symbol means that according to local laws and regulations your product should be disposed of separately from household waste. When this product reaches its end of life, take it to a collection point designated by local authorities. Some collection points accept products for free. The separate collection and recycling of your product at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. 11.1 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:
BROWAN COMMUNICATIONS All rights reserved 11 Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/CANADA Operation of this device is restricted to indoor use only. 11.2 Industry Canada statement:
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canadas license-exempt RSS(s). Operation is subject to the following two conditions :
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may cause undesired operation of the device Cet appareil contient des metteurs / rcepteurs exempts de licence qui sont conformes au (x) RSS (s) exempts de licence d'Innovation, Sciences et Dveloppement conomique Canada. L'opration est soumise aux deux conditions suivantes :
(1) Cet appareil ne doit pas causer d'interfrences
(2) Cet appareil doit accepter toute interfrence, y compris les interfrences pouvant provoquer un fonctionnement indsirable de l'appareil Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:
Cet quipement est conforme Canada limites d'exposition aux radiations dans un environnement non contrl. Cet quipement doit tre install et utilis distance minimum de 20cm entre le radiateur et votre corps. BROWAN COMMUNICATIONS All rights reserved 12 12. Configuration Downlink Command Note: Only For PIR Parameters Settings Port 102 Payload Length 5 bytes
*Note: Configuration Down-link Command should consider the duty cycle. 12.1 Payload Bytes Field 0 Cmd Cmd Command 1 2 3 4 Config Bit [7:0]
0x01 Set configuration, other values RFU Config PIR Sensor Configuration Bits [4:0]
Bit [5]
Bits [8:6]
Bits [10:9]
RFU 0 use band-pass filter, 1 use low-pass filter. Default: 0 (use BPF) RFU unsigned value , range 0-3;
window time in sec = ( + 1) 4. Default: 0 (4 sec) Bits [12:11]
unsigned value , range 0-3;
pulse counter threshold = + 1. Default: 0 (1 pulse) Bits [16:13]
unsigned value , range 0 15;
blind time in sec = ( + 1) 0.5. Default: 15 (8 sec) Bits [24:17]
detection threshold, range 0 255. Bits [31:25]
RFU Default: 16 BROWAN COMMUNICATIONS All rights reserved 13 Payload Content Command content Ex:
01000e02100 01 00e02100 => PIR parameter : 0x0021e000 Example:
=>Room Occupied:
0100e02100
=> Desk Occupied:(<=60cm) 0100148101 BROWAN COMMUNICATIONS All rights reserved 14 12.2 For Sensor Settings 12.2.1 Payload Port Bytes Field 204 0 Cmd Cmd Command 1 byte 1~4 Config Bit [7:0]
0x00 Set keepalive interval in sec. default value : 3600 sec value range: 15~65535 0x02 Set occupied interval in sec. default value : 600 sec value range: 0~65535 0x03 Set free detection time in min. default value: 5 min value range: 0~255 0x04 - Set trigger count in the occupied status. default value : 0 value range: 0~65535 0x05 - Set PIR parameters. default value: please see 12.1 0x06 Set tamper detection on/off default: enable BROWAN COMMUNICATIONS All rights reserved 15 Config Configuration (0~4 bytes ) See the table as follows:
Command Description Config Length 0 bytes 2 bytes 2 bytes 1 byte 2 bytes 4 bytes 1 byte Cmd 0x00 0x00 0x02 Get Sensor Configuration
(Only for unconfirmed downlink)
*Note: little-endian format. Set keepalive interval in sec
*Note: little-endian format. Occupied interval in sec
*Note: little-endian format. 0x03 Free detection time in min 0x04 0x05 0x06 Trigger Count in the occupied status
*Note: little-endian format. PIR Parameters (see 5.1)
*Note: little-endian format. Bit[0] = 1: Enable tamper detection, 0: Disable tamper detection Bit[7:1] = RFU 12.2.2 Command Description Payload Content Command content Ex:
00100e || 025802 || 0305 || 040000 || 0500e02100 || 0600 00 100e => Reporting interval : 0x0e10 -> 3600 sec 02 5802 => Occupied override : 0x0258 -> 600 sec 03 05 => Free detection time : 0x05 -> 5 min 04 0000 => Trigger Count in the occupied status 05 00e02100 => PIR parameter : 0x0021e000 06 00 => Disable tamper detection Example:
=>Room Occupied:
0500e02100
=> Desk Occupied:
0500148101 BROWAN COMMUNICATIONS All rights reserved 16 12.3 Response Content
(Only for unconfirmed downlink) Port 204 Payload Length 18 bytes Payload Content Response content Ex:
00100e 025802 0305 040000 0500e02100 0600 00 100e => Reporting interval : 0x0e10 -> 3600 sec 02 5802 => Occupied override : 0x0258 -> 600 sec 03 05 => Free detection time : 0x05 -> 5 min 04 0000 => Trigger Count in the occupied status 05 00e02100 => PIR parameter : 0x0021e000 06 00 => Disable tamper detection 12.4 Frame Count 1 Content Payload Length 9 bytes Payload Content Frame count 1 content Ex:
01 02200000 7ff1f102 01 => Command ID 02200000 => HW ID : 0x00002002 ( little-endian format) 7ff1f102 => FW Version : 0x02f1f17f ( little-endian format) 13. BLE FOTA Downlink Command 206 Port Payload Length 3 bytes 13.1 Payload Bytes Payload 0~2 0x444655 BROWAN COMMUNICATIONS All rights reserved 17