FCC ID: 2ADRG-BRY7011 Bluetooth Keyboard

Brydge 12.3 Pro+ User Manual Mode demploi INSERT/REMOVE TO INSERT: Place your Brydge on a flat surface and set the hinges upright to 90 degrees. Insert your Surface Pro into the hinges, one side at a time, with the Wake and Volume Buttons on top. TO REMOVE: Ensure your Brydge is on a flat surface. Place your hand towards the back of the keyboard and pull up on your Surface Pro, one side at a time. POWER To manually power on, press and hold Fn + Delete keys. The light will turn green for 2 seconds to indicate power. To manually power off, press and hold Fn + Delete keys for 2 seconds. The light will blink red momentarily to indicate its powered off. PAIR 1. Turn on your Brydge 12.3 Pro+

(Fn+Del), then press and hold the Bluetooth key for three seconds. The Delete key light will flash blue confirming your Brydge is in pairing mode. 2. On your Surface Pro, select:

Start Settings Devices Bluetooth & other devices Add Bluetooth or other device Bluetooth Brydge 12.3 Pro+

3. Type in the PIN on your Brydge 12.3 Pro+ and hit Enter. NOTE: If pairing takes longer than three minutes, the blue light will stop flashing and you will need to press the Bluetooth button again. TO CHECK BATTERY LIFE: go to Windows > Settings

> Devices > Bluetooth & other devices, and check the battery level on Brydge 12.3 Pro+. NOTE: If battery life is below 15%, the backlit key functionality will be disabled to conserve remaining battery life and the light on the Delete key will blink red. TO CHARGE: Insert the charging cable into the keyboard and plug the other end into a power source. A solid red LED on the delete key indicates the Brydge is charging. When the keyboard is fully charged, the red LED will turn off. A full charge can take up to three hours. CHARGE SLEEP/WAKE To conserve battery, your Brydge will enter sleep mode after 15 minutes of non-use. Press any key to wake it. When you close your devices together, your Brydge will put your Surface Pro into sleep mode. When you open your devices, your Brydge will wake your Surface Pro. NOTE: Your Brydge will not put your Surface Pro to sleep or wake it after 15 minutes of non-use. PRECISION TOUCHPAD The Brydge 12.3 Pro+ touchpad pairs with your Windows device as a Precision Touchpad, and therefore utilizes all of the Windows touchpad gesture capabilities. To adjust the settings and gestures of your touchpad, select Start

Settings > Devices > Touchpad. The Touchpad can be turned on and off by pressing Fn + Alt. Left Click | Click on left side of touchpad or 1 finger tap Right Click | Click on right side of touchpad or 2 finger tap Zoom In 2 finger stretch Zoom Out 2 finger pinch 2 finger swipe (up, down, left, right) Scroll Task View 3 finger swipe (left or right) See Open Windows 3 finger swipe up Show Desktop 3 finger swipe down Open Cortana 3 finger tap Switch Virtual Desktop 4 finger swipe (left or right) Open Action Center 4 finger tap KEYBOARD SHORTCUTS Touchpad Disable/Enable Fn + Alt (Hold Fn & tap Alt to disable. Hold Fn & tap Alt again to enable.) Language Switch Win + Spacebar (Use spacebar to toggle through available languages.) Copy Ctrl + C Cut Ctrl + X Paste Ctrl + V Underline Ctrl + U Italic Ctrl + I Task View Alt + Tab Page Up Fn + Up Arrow Page Down Fn + Down Arrow Home Fn + Left Arrow End Fn + Right Arrow Help Fn + F1 Undo Ctrl + Z WARRANTY Thank you for purchasing a Brydge product. This product comes with a 1-year limited hardware warranty on the terms and conditions set out in this document and at www.brydge.com/warranty. All Brydge warranties are non-

transferrable and are only available to the original end-user of the product. Warranties do not apply to products purchased from online vendors unauthorized to sell Brydge-branded product. If a defect arises during the warranty period, cease using the product and contact Brydge. To obtain warranty service, visitwww.brydge.com/support or call +1 (435) 604-0481. Brydge, at its sole discretion and option, will (1) repair the product at no charge using new parts or parts that are equivalent to new in performance and reliability, or (2) replace or exchange the product with a product of equivalent functionality and value.Brydge offers free return shipping on any approved warranty claims.A shipping label will be provided to you if you arewithin the United States. If you are outside the United States, Brydge will reimburse your return shipping to a maximum of US$15.00 after providing a copy of the shipping receipt. Australia Only: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Brydge Technologies LLC | 1912 Sidewinder Dr., Suite 104, Park City, UT 84060 USA HAVE A QUESTION? Visit www.brydge.com/support INSRER / RETIRER INSRER: Placez votre Brydge sur une surface plane et rglez les charnires 90 degrs. Insrez votre Surface Pro dans les charnires, un ct la fois, avec les boutons de Rveil et de Volume positionns sur le dessus. RETIRER: Assurez-vous que votre Brydge est sur une surface plane. Placez votre main vers larrire du clavier et tirez sur votre Surface Pro, un ct la fois. MISE EN MARCHE Pour allumer manuellement, maintenez enfonces les touches Fn + Supprimer Le voyant deviendra vert pendant 2 secondes pour indiquer la mise en marche. Pour teindre manuellement, maintenez enfonces les touches Fn + Supprimer pendant 2 secondes. Le voyant clignotera momentanment en rouge pour indiquer la mise hors tension. APPAIRER 1. Allumez votre Brydge 12.3 Pro+ (Fn + Supprimer), puis appuyez et maintenez enfonce la touche Bluetooth pendant trois secondes. Le voyant de la touche Supprimer clignotera en bleu confirmant que votre Brydge est en mode dappairage. 2. Sur votre Surface Pro, slectionnez:

Dmarrer Paramtres Appareils Bluetooth et autres appareils Ajouter Bluetooth ou un autre appareil Bluetooth Brydge 12.3 Pro+

3. Tapez le code PIN sur votre Brydge 12.3 Pro+ et appuyez sur Entre. REMARQUE: Si lappairage dure plus de trois minutes, le voyant bleu cessera de clignoter et vous devrez appuyer nouveau sur le bouton Bluetooth. CHARGE POUR VRIFIER LA DURE DE VIE DE LA BATTERIE:

accdez Windows > Paramtres > Appareils >

Bluetooth et autres appareils, et vrifiez le niveau de la batterie sur Brydge 12.3 Pro+. CHARGER : Insrez le cble de charge dans le clavier et branchez lautre extrmit dans une source dalimentation. Une DEL rouge fixe sur la touche de suppression indique que le Brydge est en charge. REMARQUE : Si la dure de vie de la batterie est infrieure 15%, la fonctionnalit de rtro-clairage des touches sera dsactive afin de conserver la dure de vie restante de la batterie et le voyant de la touche Supprimer clignotera en rouge. Lorsque le clavier est compltement charg, la DEL rouge steindra. Une charge complte peut prendre jusqu trois heures. VEILLE / RVEIL Pour conomiser la batterie, votre Brydge passera en mode veille aprs 15 minutes de non-utilisation. Appuyez sur nimporte quelle touche pour le ractiver. Lorsque vous fermez vos appareils, votre Brydge met votre Surface Pro en mode veille. Lorsque vous ouvrez vos appareils, votre Brydge rveille votre Surface Pro. REMARQUE: Votre Brydge ne mettra pas votre Surface Pro en veille ou ne la rveillera pas aprs 15 minutes de non-

utilisation. PAV TACTILE DE PRCISION Le pav tactile Brydge 12.3 Pro+ sapparie votre appareil Windows en tant que pav tactile de prcision, et utilise donc toutes les fonctionnalits gestuelles du pav tactile Windows. Pour rgler les paramtres et les gestuelles de votre pav tactile, slectionnez Dmarrer

> Paramtres> Appareils > Pav tactile. Le pav tactile peut tre activ et dsactiv en appuyant sur Fn + Alt. Clic gauche | Cliquez sur le ct gauche du pav tactile ou tapez avec 1 doigt Clic droit | Cliquez sur le ct droit du pav tactile ou tapez avec 2 doigts Zoom avant tirement 2 doigts Zoom arrire Pincement 2 doigts Faire dfiler Balayage 2 doigts

(haut, bas, gauche, droite) Afficher les tches Balayage 3 doigts

(gauche ou droite) Voir les fentres ouvertes Afficher le bureau Balayage 3 doigts vers le haut Balayage 3 doigts vers le bas Ouvrir Cortana Taper avec 3 doigts Changer de bureau virtuel Balayage 4 doigts

(gauche ou droite) Ouvrir le centre daction Taper avec 4 doigts RACCOURCIS CLAVIER Dsactiver / Activer le pav tactile Fn + Alt (maintenez Fn et appuyez sur Alt pour dsactiver. Maintenez Fn et appuyez nouveau sur Alt pour activer.) Changer de langue Win + barre despace (utilisez la barre despace pour basculer entre les langues disponibles.) Aide Fn + F1 Souligner Ctrl + U Copier Ctrl + C Italique Ctrl + I Couper Ctrl + X Annuler Ctrl + Z Coller Ctrl + V Afficher les tches Alt + Tab Haut de page Fn + Flche vers le haut Bas de page Fn + Flche vers le bas Accueil Fn + Flche gauche Fin Fn + Flche droite GARANTIE Nous vous remercions davoir achet un produit Brydge. Ce produit est accompagn dune garantie matrielle limite dun an aux conditions prvues dans ce document et sur www.brydge.com/warranty. Toute garantie Brydge ne peut tre transfre et est applicable seulement lutilisateur initial du produit. Les garanties ne sappliquent pas aux produits achets auprs de vendeurs en ligne non-autoriss vendre des produits de la marque Brydge. Pour bnficier dun service sous garantie, visitez le site www.brydge.com/support. Une preuve dachat peut tre exige pour vrifier lligibilit. VOUS AVEZ DES QUESTIONS ? Visitez www.brydge.com/support This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2020 Brydge. All Rights Reserved. 2020 Microsoft. Microsoft, the Microsoft logo, Microsoft Surface, Surface, and the Microsoft Surface logo are trademarks of the Microsoft group of companies. All other trademarks are the property of their respective owners. The Bluetooth word mark, and logos are owned by Bluetooth SIG, Inc. Use of such marks by Brydge is under license. Brydge is a trademark of Brydge Global Pte. Ltd. Other trademarks and tradenames are those of their respective owners. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) L appareil ne doit pas produire de brouillage;

(2) L appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d en compromettre le fonctionnement. REMARQUE : Cet quipement a t test et dclar conforme aux limites dun appareil numrique de classe B, conformment la partie 15 des rgles de la FCC. Ces limites sont conues pour fournir une protection raisonnable contre les interfrences nuisibles dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre de lnergie radiofrquence et, sil nest pas install et utilis conformment aux instructions, peut provoquer des interfrences nuisibles aux communications radio. Cependant, il ny a aucune garantie quaucune interfrence ne se produira dans une installation particulire. Si cet quipement provoque des interfrences nuisibles la rception radio ou tlvision, ce qui peut tre dtermin en teignant puis en rallumant lquipement, lutilisateur est encourag essayer de corriger les interfrences par une ou plusieurs des mesures suivantes :

Rorientez ou dplacez lantenne de rception. Augmentez la distance entre lquipement et le rcepteur. Connectez lquipement une prise sur un circuit diffrent de celui auquel le rcepteur est connect. Consultez le revendeur ou un technicien radio/TV expriment pour obtenir de laide Les changements ou modifications non expressment approuvs par la partie responsable de la conformit peuvent annuler le droit de lutilisateur utiliser lquipement. Cet appareil est conforme la partie 15 des rgles de la FCC. Son fonctionnement est soumis aux deux conditions suivantes :

(1) Cet appareil ne doit pas provoquer dinterfrences nuisibles, et (2) cet appareil doit accepter toute interfrence reue, y compris les interfrences pouvant entraner un fonctionnement indsirable. 2020 Brydge. Tous les droits sont rservs. 2020 Microsoft. Microsoft, le logo Microsoft, Microsoft Surface, Surface et le logo Microsoft Surface sont des marques commerciales du groupe de socits Microsoft. Toutes les autres marques sont la proprit de leurs propritaires respectifs. Le nom de marque et les logos Bluetooth sont la proprit de Bluetooth SIG et toute utilisation de marqueurs par Brydge est subordonne une licence. Brydge est une marque commerciale de Brydge Global Pte. Les autres marques et noms commerciaux sont ceux de leurs propritaires respectifs.

A B C D E 2 3 4 5 6 7 115mm Brydge Technologies LLC. Designed in Park City, UT. Assembled in China. Model: BRY701, SKU: BRY7011, US Patent 9069527, Rated 5.0V 600mA max. FCC ID: 2ADRG-BRY701, IC: 24378-BRY701 XXX-XXXXXX This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. 62mm The MIC height is 5mm*5mm

. 5 1 0 9 1

. 1 0 2 292.000.15 TK0012(BRY7011)-Silver A B C D E 1 2 3 4 5 6 7

1912 Sidewinder Dr#104, Park City, Utah United States 84060 BRYDGE GLOBAL Agent Authorization Company: BRYDGE GLOBAL Address: 1912 Sidewinder Dr#104, Park City, Utah United States 84060 Product Name: Brydge 12.3 Pro +

Model Number(s): BRY701 Product Description: Bluetooth Keyboard We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Name:

Nicholas Smith Title:

General Manager Company: BRYDGE GLOBAL Date: Jul. 22, 2020

1912 Sidewinder Dr#104, Park City, Utah United States 84060 BRYDGE GLOBAL Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Jul. 22, 2020 Subject; Request for Confidentiality FCC ID: 2ADRG-BRY7011 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Nicholas Smith Title: General Manager