FCC ID: WBKCP880-B2 LTE CAT12 Outdoor CPE

CP880+CR650 CP880+CR650 User Manual CP880+CR650 Index CHAPTER 1: Introduction .................................................................................................................. 4 1 Introduction to Outdoor CPE with Router .............................................................................. 4 2 Application Diagram ............................................................................................................... 4 CHAPTER 2: Product Overview .......................................................................................................... 5 1 Important Note for Using This Router .................................................................................... 5 2 Packing List ............................................................................................................................. 5 3.1 Panel of router ............................................................................................................ 6 3.2 Panel of ODU ............................................................................................................... 6 1 Install SIM Cards ..................................................................................................................... 8 2 Connect the Router to ODU ................................................................................................... 8 3 Mount the ODU ...................................................................................................................... 9 3.1 Cable glands Connection ............................................................................................. 9 3.2 Attach the Stainless-steel clamp to the Enclosure .................................................... 10 3.3 Wall or Pole Mounting .............................................................................................. 11 4 Choose Location ................................................................................................................... 12 5 Connect the Router .............................................................................................................. 13 CHAPTER 4: Software Features ....................................................................................................... 14 1 Getting Started ..................................................................................................................... 14 1.1 Welcome to the CPE .................................................................................................. 14 1.2 Computer Configuration Requirements .................................................................... 14 1.3 Login the Web Management Page ............................................................................ 15 2 Overview .............................................................................................................................. 17 2.1 Viewing Current Connection ..................................................................................... 17 2.2 Viewing WLAN Status ................................................................................................ 17 2.3 Viewing LTE Status ..................................................................................................... 18 2.4 Viewing WAN Status .................................................................................................. 18 3 Statistics ............................................................................................................................... 19 3.1 Viewing CPU Usage ................................................................................................... 19 3.2 Viewing Memory Usage ............................................................................................ 19 3.3 Viewing APN List ........................................................................................................ 20 3.4 Viewing Throughput Statistics ................................................................................... 20 3.5 Viewing Device List .................................................................................................... 20 4 Update .................................................................................................................................. 21 4.1 Version Manager ....................................................................................................... 21 4.2 Auto upgrade ............................................................................................................. 22 5 Settings ................................................................................................................................. 24 5.1 Viewing the Device Information ................................................................................ 24 5.2 Viewing Network ....................................................................................................... 25 5.3 Wi-Fi .......................................................................................................................... 36 5.4 Firewall ...................................................................................................................... 43 5.5 VPN ............................................................................................................................ 56 CP880+CR650 5.6 IPv6 ............................................................................................................................ 57 5.7 System ....................................................................................................................... 58 FAQs ................................................................................................................................................ 71 FCC Regulations: .............................................................................................................................. 72 FCC RF Radiation Exposure Statement ............................................................................................ 72 3 CP880+CR650 CHAPTER 1: Introduction 1 Introduction to Outdoor CPE with Router Congratulations on your purchase of the CP880+CR650 (Outdoor 4G/LTE Router). It includes two parts, an indoor unit and an outdoor unit. ODU can provide strong accessibility to the LTE network, and has been designed to meet industrial-grade IP67 dustproof and waterproof standard. Router is a wireless device which can provide ODU power supply. ODU with Router in combination is the ideal solution for residential LTE network. In addition to outdoor, it can be installed in environments such as: manufacturing plants, industrial automation, stadiums, convention halls, stadium facilities, school campuses or virtually any venue requiring a robust wireless solution. 2 Application Diagram 4 CP880+CR650 CHAPTER 2: Product Overview 1 Important Note for Using This Router 1, Do not remove, open or repair the case yourself. Contact with your Internet Service Provider or have it repaired at a qualified service center. 2, Do not plug and unplug SIM card when device is power on. 3, It is mandatory to earth ground the CP880+CR650. Improper grounding not only could damage the unit but also all equipments connected to it. 2 Packing List 5 3 Device Description 3.1 Panel of router CP880+CR650 Router LED indicator operation 3.2 Panel of ODU ODU LED indicator operation 6 CP880+CR650 7 CP880+CR650 CHAPTER 3: Hardware Installation Please make sure that you are familiar with all accident prevention and Safety procedures necessary for working at height and with electricity before start to install the device. DO NOT install the ODU during a lightning storm. 1 Install SIM Cards Step1 Use a cross screwdriver to remove the SIM card cover. Step2 Slide the SIM cards into the SIM card slots until they click into place. When the device is powered on or reboots, it automatically connects to the network. Step3 Re-attach the cover. i Make sure the ODU is turned off before you insert your SIM card. It is recommended to NOT connect the PoE cable when you do this step. Otherwise, the SIM card may be damaged. 2 Connect the Router to ODU Place a CAT5e Ethernet cable from the location of your intended Router to the desired ODU location. The maximum distance of the CAT5e cable is limited to 50 meters. If you use cable extenders to cover a greater distance, signal attenuation may occur. If you intend to use cable clamps or other methods to secure the cable, do not tighten them until you nish installing the Router and ODU. 8 CP880+CR650 Step 1 CAT5e cable to thread through the cable glands. Step 2 Connect the end of the CAT5e Ethernet cable to the PoE port of the ODU. Step 3 Wring the cable glands into ODU and seal tightly. Make sure you have inserted the SIM card into the ODU. 3 Mount the ODU See the installation instructions to mount the ODU correctly 3.1 Cable glands Connection Cable glands are tools which are vital when terminating cables in harsh or hazardous settings. Its role is to safely pass a tube, wire, or cable through an enclosure. They also act as a seal, stopping exterior impurities from causing any damage to the electrical system and the cable. Below will help you make sure that the installation of your cable gland guarantees a reliable and safe connection. Step 1 Assemble M25 cable gland Step 2 Unscrew the LAN (PoE) port and insert the supplied outdoor Ethernet cable (RJ-45) through material A-C, and then connect the RJ-45 Ethernet cable into the LAN (PoE) port. 9 CP880+CR650 Step 3:

3.1: Insert B at the back end of C 3.2: keep B close to C 3.3: then tighten A 1, Care must be taken to prevent damage to the entry threads when organizing and installing cable glands 2, Dont install cable glands while the circuits are live. 3, Cable gland parts arent well-matched with those of any other manufacturer of cable gland. 4, Take note that a cable gland isnt a user-serviceable item. 5, Cable gland sealing rings are added in the cable gland if dispatched from the factory. 3.2 Attach the Stainless-steel clamp to the Enclosure Using a screwdriver to loosen the metal hose clampsthrough the terminal equipment mounting hole, the metal hose clamps and the pole is fixed;

10 CP880+CR650 3.3 Wall or Pole Mounting Mounting on Wall

(The built-in antenna is not recommended for wall hanging type, preferred to use Pole mounting method, it can be convenient to adjust the direction of the antenna.) When the ODU terminal is hanging on the wall, the specific mounting as follows:

When install ODU on the wall, fixed four screws spacing is 68mm on wall, then the terminal equipment aligns the screws. Hang up and complete the installation. Mounting on a Pole Attach the Stainless-steel clamp to the pole which is smaller than 57mm. 11 CP880+CR650 4 Choose Location The ODU can be mounted on an antenna pole or mast or on a wall using the supplied mounting bracket. Choose a mounting point that is sturdy enough to hold the ODU, even during high winds. When choosing a location to install the ODU, please be noted that the ODUs front panel should point towards your service providers nearest base station. You do not need to be able to see the base station from the ODUs position. However, if you experience difficulties with signal reception, a Line of Sight (LoS) connection may produce better results. It is suggested that you transport the ODU to its intended installation location in its original protective package. To obtain the best radio signal level and connection quality, the CPE antenna should be aimed towards the best eNB or BS directly. To search for the best eNB direction, the user can rotate the CPE slowly and tilte CPE slightly to the best signal direction. The CPE radio signal strength level can be observed from the RF LEDs mounted on the lower panel as shown below. The more LEDs on, the better the signal strength. 12 CP880+CR650 5 Connect the Router Place a CAT5e Ethernet cable (not included) from the location of your intended Router to the desired PC location. If you intend to use cable clamps or other methods to secure the cable, do not tighten them until you nish installing the Router and ODU. 13 CP880+CR650 CHAPTER 4: Software Features 1 Getting Started 1.1 Welcome to the CPE In this document, the LTE (Long Term Evolution) CPE (customer premises equipment) will be replaced by the CPE. Carefully read the following safety symbols to help you use your CPE safely and correctly:

Additional information Optional methods or shortcuts for an action Potential problems or conventions that need to be specified 1.2 Computer Configuration Requirements For optimum performance, make sure your computer meets the following requirements. Item CPU Memory Hard disk Requirement Pentium 500 MHz or higher 128 MB RAM or higher 50 MB available space Operating system Microsoft: Windows XP, Windows Vista, or Windows 7 Display resolution Browser Mac: Mac OS X 10.5 or higher 1024 x 768 pixels or higher Internet Explorer 7.0 or later Firefox 3.6 or later Opera 10 or later Safari 5 or later Chrome 9 or later 14 CP880+CR650 1.3 Login the Web Management Page Launch web browser to login the web management page to configure and manage the CPE. The following procedure describes how to use a computer running Windows XP and Internet Explorer 7.0 to log in to the web management page of the CPE. Connect the CPE properly. 1. 2. shown in Figure 1-1. Launch Internet Explorer, enter http://192.168.1.1 in the address bar, and press Enter. As Enter the user name and password, and click Log In. Figure 0-1 3. 4. 1-2. You can log in to the web management page after the password is verified. As shown in Figure Figure 0-2 The default user name and password are both admin. If you want to view or configure the CPE more, you should use the super account to log in to the web management page. The default super user name is superadmin, and the password is admin. To protect your CPE from unauthorized access, change the password after your first login. The CPE supports diagnostic function. If you encounter problems, please contact customer service for the specific using method. 15 To ensure your data safety, it is recommended that you turn on the firewall, and conserve your login and FTP password carefully. CP880+CR650 16 CP880+CR650 2 Overview 2.1 Viewing Current Connection To view the current connection, perform the following steps:

1. Choose Overview;

2. In the Current Connection area, view the connection status, such as DL/UL Data Rate and Online time. As shown in Figure 2-1. Figure 0-3 2.2 Viewing WLAN Status To view the WLAN status, perform the following steps:

1. Choose Overview;

2. In the WLAN Status area, view the information about WLAN status, Band, Chanel NO. and Mode. As shown in Figure 2-2. Figure 0-2 17 CP880+CR650 2.3 Viewing LTE Status To view the LTE network status, perform the following steps:

1. Choose Overview;

2. In the LTE Status area, view the information about Connect status, Mode, Cell ID, Signal quality and so on. As shown in Figure 2-3. Figure 0-3 2.4 Viewing WAN Status To view the WAN status, perform the following steps:

1. Choose Overview;

2. In the WAN Status area, view the information about Connect Mode, IP, Subnet Mask, DNS Server and so on. As shown in Figure 2-4. Figure 2-4 18 CP880+CR650 3 Statistics 3.1 Viewing CPU Usage To view the CPU usage, perform the following steps:

1. Choose Statistics;

2. In the CPU Usage area, view the CPU usage information, such as Current CPU usage, Max CPU usage, Min CPU usage. As shown in Figure 3-1. Figure 3-1 3.2 Viewing Memory Usage To view the memory usage, perform the following steps:

1. Choose Statistics;

2. In the Memory Usage area, view the memory usage information, such as Total memory, Current memory usage, Max memory usage and Min memory usage. As shown in Figure 3-2. Figure 3-2 19

CP880+CR650 3.3 Viewing APN List To view the APN list, perform the following steps:

1. Choose Statistics;

2. In the APN List, view the information about APN information. As shown in Figure 3-3. Figure 3-3 3.4 Viewing Throughput Statistics To view the Throughput Statistics, perform the following steps:

1. Choose Statistics;

2. In the Throughput Statistics area, view the throughput statistics, such as APN throughput and LAN throughput. In this area, also you can choose and click the button Reset to empty the throughput statistics. As shown in Figure 3-4. 3. Figure 3-4 3.5 Viewing Device List To view the device list, perform the following steps:

1. Choose Statistics;

2. In the Device List area, view the device information which connect to the CPE, such as Device name, Mac address, IP address and Lease time. As shown in Figure 3-5. Figure 3-5 20 CP880+CR650 4 Update 4.1 Version Manager This function enables you to upgrade the software version of the CPE to a new version. Viewing Version Info To view the version info, perform the following steps:

1. Choose Update>Version Manager. 2. In the Version Info area, you can view the product name and software version. As shown in Figure 4-1. Figure 4-1 Version Upgrade To perform an upgrade successfully, connect the CPE to your computer through a network cable, save the upgrade file on the computer, and make sure the CPE is not connected to anything other than a power adapter and the computer. To perform an upgrade, perform the following steps:

1. Choose Update>Version Manager. 2. In the Version Upgrade area, click Browser. In the displayed dialog box, select the target software version file. 3. Click Open. The dialog box choses. The save path and name of the target software version 21 CP880+CR650 file are displayed in the Update file field. 4. Click Submit. 5. The software upgrade starts. After the upgrade, the CPE automatically restarts and runs the new software version. As shown in Figure 4-2. During an upgrade, do not power off the CPE or disconnect it from the computer. Figure 4-2 4.2 Auto upgrade To perform a ftp auto upgrade successfully, make sure the CPE is connected to the Internet. To perform a ftp auto upgrade, perform the following steps:

Choose Update>Auto upgrade. Enable auto upgrade. Check new firmware after connect to Internet. Set the ftp server address to the Upgrade folder box. Set Version file. //This contain the new FW name Set User name and Password. Set the Interval of checking new firmware. //Check upgrade periodic Set Start time. // The time of upgrade begin Set Random time. // Out of this time, UE will not upgrade. 10. Click Submit. As shown in Figure 4-3. If you want to check new firmware after connect to Internet, you need to enable the item of 1, The CPE will automatically upgrade according to the setting. During an upgrade, do not disconnect the power supply or operate the CPE. 2, If set interval of checking new FW, the start time and random time will shouldnt be set. 1. 2. 3. 4. 5. 6. 7. 8. 9. 22 CP880+CR650 Figure 4-3 23 CP880+CR650 5 Settings 5.1 Viewing the Device Information To view the System Information, perform the following steps:

1. Choose Settings;

2. In the System Information area, view the system status, such as Running time. As shown in Figure 5-1. Figure 5-4 Viewing the Version Information To view the Version Information, perform the following steps:

1. Choose Settings;

2. In the Device Information area, view the device information, such as Product name, Product Model, Hardware Version, Software version, UBoot version and CPE SN . As shown in Figure 5-2. Viewing LAN Status Figure 5-5 24 To view the LAN status, perform the following steps:

1. Choose Settings;

2. In the LAN Status area, view the LAN status, such as Mac address, IP address and Subnet mask. As shown in Figure 5-4. CP880+CR650 Figure 5-3 5.2 Viewing Network 5.2.1 Network Mode 1. To set the network mode, perform the following steps:

2. Choose Network >WAN Settings;

3. 4. Click Submit. As shown in Figure 5-5. In the Network Mode area, select a mode between NAT and ROUTER and Bridge Figure 5-4 5.2.2 LTE Settings To set the LTE network, perform the following steps:

1. Choose Network >LTE Settings;

2. 3. In the Settings area, you can set the configuration of LTE network;

In the Status area, you can view the LTE network connect status, such as Frequency, RSSI, RSRP, RSRQ, CINR, SINR, Cell ID and so on. As shown in Figure 5-5. 25 CP880+CR650 Figure 5-5 Connect Method Setting To set the connect method, perform the following steps:

1. Choose Network > LTE Settings;

2. In the Setting area, select a connect method between Auto and Manual. As shown in Figure 5-6. Figure 5-6 Auto Connect LTE Network To set the CPE automatically connect to the internet, perform the following steps:

1. Choose Network > LTE Settings;

2. In the Setting area, set the connect method as Auto. When the LTE network is ready, the CPE will be connected automaticity. As shown in Figure 5-7. 26 CP880+CR650 Figure 5-7 Manual Connect Mobile Network To set the mobile network manual connect to the internet, perform the following steps:

1. Choose Network > LTE Settings;

2. In the Setting area, set the connect method as Manual, when the LTE network is ready, you can set the CPE connect to the LTE network or disconnect from the LTE network. As shown in Figure 5-8. 27 CP880+CR650 Figure 5-8 5.2.3 Scan Mode This function is used to config UE mode of scan network. The default scan mode is fullband. To set the LTE network scan mode, perform the following steps:

1. 2. choose Network>Scan mode;

If select Bandlock, UE will only connect to the checked bands. Others will not be scanned. 3. Click Submit. 28 CP880+CR650 Figure 5-9 Setting Frequency (Earfcn) To set the frequency, perform the following steps:

1 Choose Network>Scan Mode. 2 In the Scan Mode area, choose EARFCN Lock. 3 In the EARFCN Lock area, you can set an EARFCN, then click Add to add it to the EARFCN lock list. 4 Click Submit. As shown in Figure 5-10. Figure 5-10 Setting PCI LOCK To set the pci lock perform the following steps:

1. Choose Network>Scan Mode. 2. In the Scan Mode area, choose PCI Lock. 29 3. In the PCI Lock area, you can set EARFCN and PCI of the cell, then click Add to add it to the PCI lock list. 4. Click Submit. As shown in Figure 5-11. CP880+CR650 Figure 5-11 5.2.4 APN Management To set and manage APN, perform the following steps:

1. Choose Network>APN Management. 2. 3. Choose an APN number which you want to set, there are 4 APNs selected. 4. In the APN Management area, you can set the APN. In the APN Setting area you can set the APN parameters, such as enable or disable the APN, APN name, profile name. Set the authentication type (chap or pap or none) and the username, password of it. Set the PDN type: IPv4 or IPv6 or IPv4/v6 dual stack. 5. 6. 7. Click Submit. As shown in Figure 5-12. If you want set an APN as default gateway, you should check that is enabled. And we can also set the APN apply to SNMP or TR069. Figure 5-12 30 CP880+CR650 5.2.5 PIN Management To manage the PIN, you can perform the following operations on the PIN Management page:

Enable or disable the PIN verification. Verify the PIN. Change the PIN. Set automatic verification of the PIN. As shown in Figure 5-13 Figure 5-13 Viewing the Status of the USIM Card To view the status of the USIM card, perform the following steps:

1 Choose Network >PIN Management. 2 View the status of the USIM card in the USIM card status field. Enabling PIN Verification To enable PIN verification, perform the following steps:

1 Choose Network >PIN Management. 2 Set PIN verification to Enable. 3 Enter the PIN (4 to 8 digits) in the Enter PIN box. 4 Click Submit. Disabling PIN Verification To disable PIN verification, perform the following steps:

1 Choose Network >PIN Management. 2 Set PIN verification to Disable. 3 Enter the PIN (4 to 8 digits) in the Enter PIN box. 4 Click Submit. Verifying the PIN If PIN verification is enabled but the PIN is not verified, the verification is required. To verify the PIN, perform the following steps:

1 Choose Network >PIN Management. 31 CP880+CR650 2 Enter the PIN (4 to 8 digits) in the PIN box. 3 Click Submit. Changing the PIN The PIN can be changed only when PIN verification is enabled and the PIN is verified. To change the PIN, perform the following steps:

1 Choose Network>PIN Management. 2 Set PIN verification to Enable. 3 Set Change PIN to Enable. 4 Enter the current PIN (4 to 8 digits) in the PIN box. 5 Enter a new PIN (4 to 8 digits) in the New PIN box. 6 Repeat the new PIN in the Confirm PIN box. 7 Click Submit. Setting Automatic Verification of the PIN You can enable or disable automatic verification of the PIN. If automatic verification is enabled, the CPE automatically verifies the PIN after restarting. This function can be enabled only when PIN verification is enabled and the PIN is verified. 1 To enable automatic verification of the PIN, perform the following steps:

2 Choose Network > PIN Management. 3 Set Pin verification to Enable. 4 Set Remember my PIN to Enable. 5 Click Submit. Verifying the PUK If PIN verification is enabled and the PIN fails to be verified for three consecutive times, the PIN will be locked. In this case, you need to verify the PUK and change the PIN to unlock it. To verify the PUK, perform the following steps:

Choose Network> PIN Management. Enter the PUK in the PUK box. Enter a new PIN in the New PIN box. 4. Repeat the new PIN in the Confirm PIN box. Click Submit. 1. 2. 3. 5.2.6 Dual SIM If you have insert two SIM card in device, and want to exchange them. Please click here to switch them. As shown in Figure 5-14 32 CP880+CR650 Figure 5-14 5.2.7 SIM Lock If you want to connect a specify network, and the CPE cant connect other network, you can set a SIM lock. To set the SIM lock, perform the following steps:

1. Choose Network>SIM Lock. 2. 3. Click add to add the PLMN in the lock list. 4. Click Submit. As shown in Figure 5-15. Input the PLMN you want to lock in the PLMN box. 5.2.8 LAN Setting Figure 5-15 Setting LAN Host Parameters By default, the IP address is 192.168.0.1 with a subnet mask of 255.255.255.0. You can change the host IP address to another individual IP address that is easy to remember. Make sure that IP address is unique on your network. If you change the IP address of the CPE, you need to access the web management page with the new IP address. To change the IP address of the CPE, perform the following steps:

1. Choose Network>LAN Settings. 2. In the LAN Host Settings area, set IP address and subnet mask. 33 In the DHCP Setting area, set the DHCP server to Enable. 3. 4. Click Submit. As shown in Figure 5-16. CP880+CR650 Configuration the DHCP Server Figure 5-16 DHCP enables individual clients to automatically obtain TCP/IP configuration when the server powers on. You can configure the CPE as a DHCP server or disable it. When configured as a DHCP server, the CPE automatically provides the TCP/IP configuration for the LAN clients that support DHCP client capabilities. If DHCP server services are disabled, you must have another DHCP server on your LAN, or each client must be manually configured. To configure DHCP settings, perform the following steps:

1. 2. 3. Choose Network Setting > LAN Settings. Set the DHCP server to Enable. Set Start IP address. they must be on the same network segment. 4. Set End IP address. they must be on the same network segment. 5. Set Lease time. value. 6. Click Submit. As shown in Figure 5-17. This IP address must be different from the IP address set on the LAN Host Settings area, but This IP address must be different from the IP address set on the LAN Host Settings area, but Lease time can be set to 1 to 10,080 minutes. It is recommended to retain the default 34 CP880+CR650 Figure 5-17 5.2.9 DMZ Settings If the demilitarized zone (DMZ) is enabled, the packets sent from the WAN are directly sent to a specified IP address on the LAN before being discarded by the firewall. To set DMZ, perform the following steps:

1. Choose Network > DMZ Settings. 2. 3. 4. Set DMZ to Enable.

(Optional) Set ICMP Redirect to Enable. Set Host address. This IP address must be different from the IP address set on the LAN Host Settings page, but they must be on the same network segment. 5. Click Submit. As shown in Figure 5-18. Figure 5-18 5.2.10 Static Route Add Static Route To add a static route, perform the following steps:

Choose Network Setting>Static Route. 1. 2. Click Add list. 3. 4. 5. Set the Dest IP address and Subnet mask. Select an Interface from the drop-down list. If you select LAN as the interface, you need set a Gateway. 35 6. Click Submit. As shown in Figure 5-19. CP880+CR650 Figure 5-19 Modify Static Route To modify an access restriction rule, perform the following steps:

1. Choose Firewall>Static Route. 2. Choose the item to be modified, and click Edit. 3. Repeat steps 3 through 5 in the previous procedure. 4. Click Submit. As shown in Figure 5-20. Figure 5-20 Delete Static Route To delete a static route, perform the following steps:

1. Choose Firewall>Static Route. 2. Choose the item to be deleted, and click Delete. 5.3 Wi-Fi For SRP serial, SRP210 dont support WIFI. SRP410-a and SRP410-b support 2.4G&5G dual band WIFI. 36 CP880+CR650 5.3.1 WLAN Status To view the WLAN status, perform the following steps:

1. Choose Wi-Fi;

2. In the WLAN Status area, view the information about Wi-Fi status, 2.4G, 5G and Device list. As shown in Figure 5-22. Figure 5-22 5.3.2 WLAN Settings This function enables you to configure the Wi-Fi parameters. Setting General Parameters To configure the general Wi-Fi settings, perform the following steps:

1. Choose Wi-Fi > Wi-Fi Settings. 2. 3. In the General Settings area, set WLAN to Enable. Set Mode to one of the values described in the following table:

Parameter Value 802.11 a/n/ac 802.11b/g/n 802.11b/g Description The Wi-Fi client can connect to the CPE in 802.11a, 802.11n, or 802.11ac mode in 5G If your device supports ISM frequency. 802.11ac Protocol, we suggest to use 802.11ac protocol for better experience. The Wi-Fi client can connect to the CPE in 802.11b, 802.11g, or 802.11n mode. If the client connects to the CPE in 802.11n mode, the Advanced Encryption Standard (AES) encryption mode is required. The Wi-Fi client can connect to the CPE in 37 CP880+CR650 802.11b or 802.11g mode. The Wi-Fi client can connect to the CPE in 802.11b mode. The Wi-Fi client can connect to the CPE in 802.11g mode. 802.11b 802.11g Set the Channel No. 2.4G from 1 to 11, 5G from 40 to 165. 4. 5. Click Submit. As shown in Figure 5-23. Figure 5-23 Setting SSID Profile After you configure the CPE on the SSID Profile page, the Wi-Fi client connects to the CPE based on preset rules, improving access Firewall. To configure the CPE on the SSID Profile page, perform the following steps:

1. Choose Wi-Fi > Wi-Fi Settings. 2. Set SSID. The SSID can contain 1 to 32 ASCII characters. It cannot be empty and the last character cannot be a blank character. In addition, the SSID cannot contain the following special characters: / ' = " \ &

The Wi-Fi client connects to the CPE using the found SSID. 3. Set Maximum number of devices. This parameter indicates the maximum number of Wi-Fi clients that connect to the CPE. 38 CP880+CR650 A maximum of 32 clients can connect to the CPE. 4. Set Hide SSID broadcast to Enable. If the SSID is hidden, the client cannot detect the CPE's Wi-Fi information. 5. Set AP isolation to Enable. 6. Set Security. The clients can connect to the CPE but cannot communicate with each other. If Security is set to NONE (not recommended), Wi-Fi clients directly connect to the CPE. This Firewall level is low. If Security is set to WEP, Wi-Fi clients connect to the CPE in web-based encryption mode. If Security is set to WPA-PSK, Wi-Fi clients connect to the CPE in WPA-PSK encryption mode. If Security is set to WPA2-PSK, Wi-Fi clients connect to the CPE in WPA2-PSK encryption mode. This mode is recommended because it has a high Firewall level. If Security is set to WPA-PSK & WPA2-PSK, Wi-Fi clients connect to the CPE in WPA-PSK&WPA2-PSK encryption mode. 7. Set the encryption mode. If WEP Sets to Authentication mode Shared authentication: The client Description connects to the CPE in shared authentication mode. Open authentication: The client connects to the CPE in open authentication mode. Both: The client connects to the CPE in shared or open authentication mode. 128bit: Only 13 ASCII characters or 26 hex characters can be entered in the Key 1 to Key 4 boxes. 64bit: Only 5 ASCII characters or 10 hex characters can be entered in the Key 1 to Key 4 boxes. This value can be set to 1, 2, 3, or 4. After a key index is selected, the corresponding key takes effect. Only 8 to 63 ASCII characters or 8 to 64 hex characters can be entered. This value can be set to TKIP+AES, AES, or TKIP. Only 8 to 63 ASCII characters or 8 to 64 hex characters can be entered. This value can be set to TKIP+AES, AES, or TKIP. Only 8 to 63 ASCII characters or 8 to 64 hex characters can be entered. Encryption password length WPA-PSK WPA-PSK Current password index WPA encryption WPA2-PSK(reco mmended) WPA-PSK WPA encryption WPA-PSK &

WPA2-PSK WPA-PSK 39 WPA encryption This value can be set to TKIP+AES, AES, or TKIP. CP880+CR650 8. Click Submit. As shown in Figure 5-24. Figure 5-24 5.3.3 Access Management Setting the Access Policy This function enables you to set access restriction policies for each SSID to manage access to the CPE. To configure Wi-Fi MAC control settings, perform the following steps:

1. Choose Wi-Fi > Access Management. 2. In the WLAN Access List Settings area, set Access Policy. 3. The access policy can be set to Disable, Blacklist or Whitelist. If SSID's MAC Access is set to Disable, access restrictions do not take effect. If SSID's MAC Access is set to Blacklist, only the devices that are not in the blacklist can connect to the CPE. If SSID's MAC Access is set to Whitelist, only the devices in the whitelist can connect to the CPE. 4. Click Submit. As shown in Figure 5-25. 40 CP880+CR650 Figure 5-25 Managing the Wi-Fi Access List This function enables you to set the SSID access policies based on MAC addresses. To add an item to the Wi-Fi access list, perform the following steps:

1. Choose Wi-Fi > Access Management. 2. Click Add. 3. Set MAC address. 4. Click Submit. As shown in Figure 5-26. Figure 5-26 To modify an item in the Wi-Fi access list, perform the following steps:

1. Choose Wi-Fi > Access Management. 2. Click Edit MAC List. 3. Choose the item to be modified, and click Edit. 4. Set MAC address. 5. Set one of the SSID to Enable to make the MAC address take effect for the SSID. 6. Click Submit. As shown in Figure 5-27. 41 CP880+CR650 To delete an item from the Wi-Fi access list, perform the following steps:

1. Choose Wi-Fi > Access Management. 2. Choose the item to be deleted, and click Delete. As shown in Figure 5-28. Figure 5-27 Figure 5-28 42 5.3.4 WPS Settings Wi-Fi Protected Setup (WPS) enables you to simply add a wireless client to the network without needing to specifically configure the wireless settings, such as the SSID, Firewall mode and passphrase. You can use either the WPS button or PIN to add the wireless client. To configure Wi-Fi WPS settings, perform the following steps:

1. Choose Wi-Fi > WPS Settings. 2. Set WPS to Enable. 3. Select WPS mode to PBC or router PIN as you want. 4. Click Submit. As shown in Figure 5-29. CP880+CR650 Figure 5-69 5.3.5 Guest Network The function is to provide a wifi network for guests. To configure the Guest Network, perform the following steps:

1.Choose Wi-Fi > Guest Network. 2.In the Guest Network area, set Guest network to Enable. As shown in Figure 5-30. Figure 5-30 5.4 Firewall 5.4.1 Setting Firewall This page describes how to set the firewall. If you enable or disable the firewall, you can modify the configuration. To set the firewall, perform the following steps:

1. Choose Firewall>Firewall Setting. 43 2. Choose Enable or Disable to modify the configuration. 3. Click Submit. As shown in Figure 5-31. CP880+CR650 Figure 5-31 If you choose enable the firewall, you can modify the configuration about firewall, such as Mac filter, IP filter, URL filter and so on. If you choose disable, you cant modify any configurations about the firewall. 5.4.2 MAC Filtering This page enables you to configure the MAC address filtering rules. Enabling MAC Filter To enable MAC address filter, perform the following steps:

1. Choose Firewall>MAC Filtering 2. Set MAC filtering to Enable. 3. Click Submit. As shown in Figure 5-32. Figure 0-32 Disabling MAC Filter To disable MAC address filter, perform the following steps:

1. Choose Firewall>MAC Filtering 2. Set MAC filtering to Disable. 3. Click Submit. As shown in Figure 5-33. 44 CP880+CR650 Figure 0-33 Setting Allow access network within the rules To set allow access network within the rules, perform the following steps:

1. Choose Firewall>MAC Filtering. 2. 3. Click Submit. As shown in Figure 5-34. Set Allow access network within the rules. Figure 0-74 Setting Deny access network within the rules To set deny access network within the rules, perform the following steps:

1. Choose Firewall>MAC Filtering. 2. 3. Click Submit. As shown in Figure 5-35. Set Deny access network within the rules. Figure 0-35 45 CP880+CR650 Adding MAC Filtering rule To add a MAC filtering rule, perform the following steps:

1. Choose Firewall>MAC Filtering. 2. Click Add list. 3. 4. Click Submit. As shown in Figure 5-36. Set MAC address. Figure 0-36 Modifying MAC Filtering rule To modify a MAC address rule, perform the following steps:

1. Choose Firewall>MAC Filtering. 2. Choose the rule to be modified, and click Edit. 3. 4. Click Submit. As shown in Figure 5-37. Set MAC address. Figure 0-37 Deleting MAC Filtering rule To delete a MAC address filter rule, perform the following steps:

1. Choose Firewall>MAC Filtering. 2. Choose the rule to be deleted, and click Delete. As shown in Figure 5-38. 46 CP880+CR650 Figure 0-38 5.4.3 IP Filtering Data is filtered by IP address. This page enables you to configure the IP address filtering rules. Enabling IP Filtering To enable IP Filtering, perform the following steps:

1. Choose Firewall>IP Filtering. 2. Set IP Filtering Enable. 3. Click Submit. As shown in Figure 5-39. Figure 0-39 Disabling IP Filtering To disable IP Filtering, perform the following steps:

1. Choose Firewall>IP Filtering. 2. Set IP Filtering Disable. 3. Click Submit. As shown in Figure 5-40. Figure 0-340 Setting Allow access network outside the rules To set allow access network, perform the following steps:

1. Choose Firewall>IP Filtering. 2. Set Allow access network outside the rules. 47 3. Click Submit. As shown in Figure 5-41. CP880+CR650 Figure 0-41 Setting Deny access network outside the rules To set allow access network, perform the following steps:

1. Choose Firewall>IP Filtering. 2. 3. Click Submit. As shown in Figure 5-42. Set Deny access network outside the rules. Figure 0-42 Adding IP Filtering rule Add an IP address filtering rule, perform the following steps:

1. Choose Firewall>IP Filtering. 2. Click Add list. 3. 4. 5. Set Service. Set Protocol. In the Source IP Address Range box, enter the source IP address or IP address segment to be filtered. In the Source port range box, enter the source port or port segment to be filtered. In the Destination IP Address Range box, enter the destination IP address or IP address segment to be filtered. In the Destination port Range box, enter the destination port or port segment to be filtered. In the Status box, choose a status the rule will be executed. 9. 10. Click Submit. As shown in Figure 5-43. 6. 7. 8. 48 CP880+CR650 Figure 0-43 Modifying IP Filtering rule To modify an IP filtering rule, perform the following steps:

1. Choose Firewall > IP Filtering. 2. Choose the rule to be modified, and click Edit. 3. Repeat steps 3 through 9 in the previous procedure. 4. Click Submit. As shown in Figure 5-44. Figure 0-44 49 CP880+CR650 Deleting IP Filtering rule To delete an IP address filtering rule, perform the following steps:

1. Choose Firewall > IP Filtering. 2. Choose the rule to be deleted, and click Delete. As shown in Figure 5-45. Figure 0-45 5.4.4 URL Filtering Data is filtered by uniform resource locator (URL). This page enables you to configure URL filtering rules. Enabling URL Filtering To enable URL Filtering, perform the following steps:

1. Choose Firewall>URL Filtering. 2. Set URL Filtering to Enable. 3. Click Submit. As shown in Figure 5-46. Figure 0-46 Disabling URL Filtering To disable URL Filtering, perform the following steps:

1. Choose Firewall>URL Filtering. 2. Set URL Filtering to Disable. 3. Click Submit. As shown in Figure 5-47. Adding URL Filtering list Figure 0-47 50 CP880+CR650 To add an URL filtering list, perform the following steps:

1. Choose Firewall>URL Filtering. 2. Click Add list. 3. Set URL. 4. Click Submit. As shown in Figure 5-48. Figure 0-48 Modify URL Filtering list To modify an URL filtering rule, perform the following steps:

1. Choose Firewall>URL Filtering. 2. Choose the rule to be modified, and click Edit. 3. 4. Click Submit. As shown in Figure 5-49. Set URL address. Figure 0-49 Deleting URL Filtering list To delete an URL list, perform the following steps:

1. Choose Firewall>URL Filtering. 2. Choose the item to be deleted, and click Delete. As shown in Figure 5-50. Figure 0-50 51 CP880+CR650 5.4.5 Port Forwarding When network address translation (NAT) is enabled on the CPE, only the IP address on the WAN side is open to the Internet. If a computer on the LAN is enabled to provide services for the Internet (for example, work as an FTP server), port forwarding is required so that all accesses to the external server port from the Internet are redirected to the server on the LAN. Adding Port Forwarding rule To add a port forwarding rule, perform the following steps:

1. Choose Firewall > Port Forwarding. 2. Click Add list. 3. Set Service. 4. Set Protocol. 5. Set Remote port range. 6. Set Local host. 7. Set Local port. The port number ranges from 1 to 65535. This IP address must be different from the IP address that is set on the LAN Host Settings page, but they must be on the same network segment. The port number ranges from 1 to 65535. 8. Click Submit. As shown in Figure 5-50. Figure 0-51 52 CP880+CR650 Modifying Port Forwarding rule To modify a port forwarding rule, perform the following steps:

1. Choose Firewall > Port Forwarding. 2. Choose the item to be modified, and click Edit. 3. Re-config the service, protocol, and ports. 4. Click Submit. As shown in Figure 5-52. Figure 0-52 Deleting Port Forwarding rule To delete a port forwarding rule, perform the following steps:

Choose Firewall > Port Forwarding. Choose the item to be deleted, and click Delete. As shown in Figure 5-53. 5.4.6 Access Restriction Figure 0-53 53 1. 2. CP880+CR650 Figure 5-54 Add Access Restriction To add an access restriction rule, perform the following steps:

1. Choose Security>Access Restriction. 2. Click Add list. 3. 4. 5. 6. 7. Click Submit. Set Access Restriction to Enable. Set Access Restriction Name. Set Device MAC address or IP address. Set Weekdays and time. Modify Access Restriction To modify an access restriction rule, perform the following steps:

1. Choose Security>Access Restriction. 2. Choose the item to be modified, and click Edit. 3. Repeat steps 4 through 6 in the previous procedure. 4. Click Submit. Delete Access Restriction To delete a access restriction rule, perform the following steps:

1. Choose Security>Access Restriction. 54 CP880+CR650 2. Choose the item to be deleted, and click Delete. 5.4.7 UPnP On this page, you can enable or disable the Universal Plug and Play (UPnP) function. To enable UPnP, perform the following steps:

1. Choose Firewall > UPnP. 2. Set UPnP to Enable. 3. Click Submit. As shown in Figure 5-55. Figure 0-55 5.4.8 DoS On this page, you can enable or disable the Denial of service (DoS) function. 1. 2. Choose Firewall > DoS. Set UPnP to Enable. 3. Click Submit. As shown in Figure 5-56. 55 CP880+CR650 Figure 0-86 5.5 VPN This function enables you to connect the virtual private network (VPN). To connect the VPN, perform the following steps:

1. Choose VPN. 2. 3. 4. Enter Username and Password. 5. Click Submit. 6. You can view the status in VPN Status area. As shown in Figure 5-57. In the VPN Settings area, enable VPN. Select a protocol from Protocol drop-down list. Figure 5-57 56 CP880+CR650 5.6 IPv6 Internet Protocol version 6 (IPv6) is the most recent version of the Internet Protocol (IP). Every device on the Internet is assigned an unique IP address for identification and location definition. 5.6.1 Status The status page shows IPv6 information. As shown in Figure 5-58. Figure 5-58 5.6.2 IPv6 WAN Settings In this page, user can enable or disable IPv6 function. Meanwhile, user can set WAN Connection Type and the type of DNS.As shown in Figure 5-59 Figure 5-59 57 5.6.3 IPv6 LAN Settings In this page, user can choose the Auto Configuration Type. As shown in Figure 5-60. CP880+CR650 Figure 5-60 5.7 System 5.7.1 Maintenance Reboot This function enables you to restart the CPE. Settings take effect only after the CPE restarts. To restart the CPE, perform the following steps:

1. Choose System>Maintenance. 2. Click Reboot. As shown in Figure 5-61. The CPE then restarts. Figure 5-61 Reset This function enables you to restore the CPE to its default settings. To restore the CPE, perform the following steps:

1. Choose System>Maintenance. 2. Click Factory Reset. As shown in Figure 5-62. The CPE is then restored to its default settings. 58 CP880+CR650 Figure 5-62 Backup Configuration File You can download the existing configuration file to back it up. To do so:

1. Choose System>Maintenance. 2. Click Download on the Maintenance page. 3. In the displayed dialog box, select the save path and name of the configuration file to be backed up. 4. Click Save. As shown in Figure 5-63. The procedure for file downloading may vary with the browser you are using. Figure 5-63 Upload Configuration File You can upload a backed-up configuration file to restore the CPE. To do so:

1. Choose System>Maintenance. 2. Click Browse on the Maintenance page. 3. 4. Click Open. 5. The dialog box chooses. In the box to be right of Configuration file, the save path and name In the displayed dialog box, select the backed-up configuration file. of the backed-up configuration file are displayed. 6. Click Upload. As shown in Figure 5-64. The CPE uploads the backed-up configuration file. The CPE then automatically restarts. Figure 5-64 59 CP880+CR650 5.7.2 TR069 TR-069 is a standard for communication between CPEs and the auto-configuration server (ACS). If your service provider uses the TR069 automatic service provision function, the ACS automatically provides the CPE parameters. If you set the ACS parameters on both the CPE and ACS, the network parameters on the CPE are automatically set using the TR-069 function, and you do not need to set To configure the CPE to implement the TR-069 function, perform the following steps:

other parameters on the CPE. Choose System>TR069. Set acs URL source. There are two methods, such as URL and DHCP. In the ACS URL box, enter the ACS URL address. Enter ACS user name and password for the CPE authentication. To use the CPE to access the ACS, you must provide a user name and password for authentication. The user name and the password must be the same as those defined on the ACS. If you set Periodic inform to Enable, set Periodic inform interval. Set connection request user name and password. Click Submit. As shown in Figure 5-65. 5.7.3 SNMP You can enable SNMP and set config SNMP trap. Figure 5-65 60 1. 2. 3. 4. 5. 6. 7. The UE will actively report changes of some certain values to the SNMP server. CP880+CR650 Figure 5-66 5.7.4 Date & Time You can set the system time manually or synchronize it with the network. If you select Sync from network, the CPE regularly synchronizes the time with the specified Network Time Protocol (NTP) server. If you enable daylight saving time (DST), the CPE also adjusts the system time for DST. To set the date and time, perform the following steps:

1. Choose System > Date & Time. 2. Select Set manually. 3. Set Local time or click Sync to automatically fill in the current local system time. 4. Click Submit. As shown in Figure 5-67. Figure 5-67 To synchronize the time with the network, perform the following steps:

1. Choose System > Date & Time. 2. Select Sync from network. 3. From the Primary NTP server drop-down list, select a server as the primary server for time 61 CP880+CR650 4. From the Secondary NTP server drop-down list, select a server as the IP address of the secondary 5. If you dont want to use other NTP server, you need to enable Optional ntp server, and set a synchronization. server for time synchronization. server IP address. 6. Set Time zone. 7. Click Submit. As shown in Figure 5-68. Figure 5-68 To set DST, perform the following steps:

Choose System>Date&Time. Set DST enable. Set Start Time and End Time. Click Submit. As shown in Figure 5-69. The CPE will automatically provide the DST time based on the time zone. Figure 5-69 62 1. 2. 3. 4. CP880+CR650 Dynamic Domain Name Server (DDNS) service is used to map the user's dynamic IP address to a 5.7.5 DDNS fixed DNS service. 1. Choose System > DDNS. 2. Set DDNS to Enable. To configure DDNS settings, perform the following steps:

3. In Service provider, choose DynDNS.org or oray.com. 4. Enter Domain name and Host name. For example, if the domain name provided by your service provider is test.customtest.dyndns.org, enter customtest.dyndns.org as Domain name, and test as Host name. 5. Enter User name and Password. 6. Click Submit. As shown in Figure 5-70. Figure 5-70 5.7.6 Diagnosis If the CPE is not functioning correctly, you can use the diagnosis tools on the Diagnosis page to preliminarily identify the problem so that actions can be taken to solve it. 63 CP880+CR650 If the CPE fails to access the Internet, run the ping command to preliminarily identify the problem. To Ping do so:

1. 2. 3. 4. Choose System>Diagnosis. In the Method area, select Ping. Set Packet size and Timeout. 5. Set Count. 6. Click Ping. As shown in Figure 5-71. Enter the domain name in the Target IP or domain field, for example, www.google.com. Wait until the ping command is executed. The execution results are displayed in the Results box. Figure 5-71 If the CPE fails to access the Internet, run the Traceroute command to preliminarily identify the Traceroute problem. To do so:

Choose System>Diagnosis. In the Method area, select Traceroute. 1. 2. 64 Enter the domain name in the Target IP or domain field. For example, www.google.com. CP880+CR650 Set Maximum hops ad Timeout. Click Traceroute. As shown in Figure 5-72 Wait until the traceroute command is executed. The execution results are displayed in the Results Figure 5-72 Port mirroring is used on a network switch to send a copy of network packets seen on one 5.7.7 Port Mirror switch port. To do so:

Choose System>Port Mirror. Enable Port Mirror. Select the WAN Interface which you want a copy. Type the Monitor IP, where the copy will send to. Click Submit. As shown in Figure 5-73. 65 3. 4. 5. box. 1. 2. 3. 4. 5. CP880+CR650 5-73 Figure The syslog record user operations and key running events. 5.7.8 Syslog Local To set the syslog to local, perform the following steps:

Choose System>Syslog. In the Setting area, set the method to Local. In the Level drop-down list, select a log level. Click Submit. As shown in Figure 5-74. Figure 5-74 Viewing local syslog To view the local syslog, perform the following steps:

In the Keyword box, set a keyword. Click Pull, the result box will display. 66 1. 2. 3. 4. 1. 2. CP880+CR650 Network To set the syslog to network, perform the following steps:

1. 2. 3. 4. 5. Choose System>Syslog. In the Setting area, set the method to Network. In the Level drop-down list, select a log level. In the Forward IP address box, set an IP address. Click Submit. As shown in Figure 5-75. The syslog will transmit to some client to display through network. Figure 5-75 5.7.9 Uart To use the RS232 or RS485 communicate, we should setting the value here. 67 CP880+CR650 Figure 5-76 The target IP is terminals IP. The port should be set the same as terminal. 5.7.10 WEB Setting To configure the parameters of WEB, perform the following steps:

1. Choose System> WEB Setting. 2. Set HTTP enable. If you set HTTP disable, you will cant login the web management page with the HTTP protocol from WAN side. Set HTTP port. If you want to change the login port, you can set a new port in the box, the default HTTP port is 80. Set HTTPS enable. If you want to login the web management page with the HTTPS protocol from WAN side, you need to enable the HTTPS. If you want to login the web management page form the WAN, you need to Enable Allowing login from WAN. Set the HTTPS port. 6. 7. Click Submit. As shown in Figure 5-77. 3. 4. 5. 68 CP880+CR650 Figure 5-77 5.7.11 Account This function enables you to change the login password of the user. After the password changes, enter the new password the next time you login. To change the password, perform the following steps:

1. Choose System>Account. 2. Select the user name, if you want to change the password of normal user, you need to set Enable User enable. 3. Enter the current password, set a new password, and confirm the new password. 4. New password and Confirm password must contain 5 to 15 characters. 5. Click Submit. As shown in Figure 5-78. Figure 5-78 69 5.7.12 Logout To logout the web management page, perform the following steps:

1. Choose System and click Logout It will return to the login page. CP880+CR650 70 CP880+CR650 FAQs The POWER indicator does not turn on. Make sure that the power cable is connected properly and the CPE is powered on. Make sure that the power adapter is compatible with the CPE. Fails to Log in to the web management page. Make sure that the CPE is started. Verify that the CPE is correctly connected to the computer through a network cable. If the problem persists, contact authorized local service suppliers. The CPE fails to search for the wireless network. Check that the power adapter is connected properly. Check that the CPE is placed in an open area that is far away from obstructions, such as concrete or wooden walls. Check that the CPE is placed far away from household electrical appliances that generate strong electromagnetic field, such as microwave ovens, refrigerators, and satellite dishes. If the problem persists, contact authorized local service suppliers. The power adapter of the CPE is overheated. The CPE will be overheated after being used for a long time. Therefore, power off the CPE when you are not using it. Check that the CPE is properly ventilated and shielded from direct sunlight. The parameters are restored to default values. If the CPE powers off unexpectedly while being configured, the parameters may be restored to the default settings. After configuring the parameters, download the configuration file to quickly restore the CPE to the desired settings. 71 CP880+CR650 FCC Regulations:

This mobile phone complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 15.19 (a)(3) 15.21 15.105 (b) This mobile phone has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To comply with FCC RF Exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for the transmitter must be installed to provide a separation distance of at least 25cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmit. 72

( BT Band 42/43/48 WIRELESS Product Name :LTE CAT12 Outdoor CPE Model :CP880-B FCC ID :WBKCP880-B2 S/N :XXXXXXXXXXXXXXXXX IMEI :XXXXXXXXXXXXXXXX Supply Voltage :24V===0.5A Manufacture :Bravo Tech Inc

BTI Wireless 6185 Phyllis Drive #D,Cypress,California,United States 90630 Tel: +1-214-850-1676 ; Fax: +1-714-788-6105 Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attention: Application Examiner / Review Engineer Date: September 5, 2020 Subject: Request for a Change in Identification per Section 2.933 of the FCC Rules To The Commission:

This change in identification request applies for a new FCC ID as established in 47 CFR 2.933(b) for a currently approved device. This application by BT! Wireless will establish a new FCC ID: WBKCP880-B2 for the purpose of marketing. The original grant to Smawave Technology Co. ,Ltd, with FCC ID: 2AUSHSRW410, will remain in effect. An authorization letter by Smawave Technology Co. ,Ltd is attached. Per 2.933(b) 1.) The original identification is: FCC ID: 2AUSHSRW410 2.) The original granted date is: 08/13/2020 3.) The equipment is electrically identical. 4.) The original test results are applicable and representative of this device 5.) FCC ID label, location info, External and Internal photos are included in this application. The following files are electronically submitted as attachments:

- Cover Letter pas ~ sa so)

- LV Label and Locallon Hilo

-Test report/Tsup

-Tune Pro Sincerely yours, Rr chowal A Contact Person: Richard Xu E-mail: richard.xu@btiwireless.com