FCC ID: WBKCP880-B LTE Outdoor CPE

CP880-B LTE CPE User Manual Index 3 5 4.1 1.1 1.2 1.3 1 Getting Started ............................................................................................................................... 4 Welcome to the CPE .................................................................................................. 4 Computer Configuration Requirements .................................................................... 4 Logging In to the Web Management Page ................................................................ 4 2 Overview ................................................................................................................................... 6 Viewing Current Connection ..................................................................................... 6 2.1 Viewing LTE Status ..................................................................................................... 6 2.2 2.3 Viewing WAN Status .................................................................................................. 6 Statistics .................................................................................................................................... 8 Viewing CPU Usage ................................................................................................... 8 3.1 Viewing Memory Usage ............................................................................................ 8 3.2 3.3 Viewing APN List........................................................................................................ 9 Viewing Throughput Statistics ................................................................................... 9 3.4 3.5 Viewing Device List .................................................................................................... 9 4 Update..................................................................................................................................... 11 Version Manager ..................................................................................................... 11 Viewing Version Info ........................................................................................................ 11 Version Upgrade .............................................................................................................. 11 4.2 Auto upgrade........................................................................................................... 12 Settings .................................................................................................................................... 14 5.1 Viewing the Device Information .............................................................................. 14 Viewing the Version Information .................................................................................... 14 Viewing LAN Status ......................................................................................................... 14 Viewing Network ..................................................................................................... 15 LTE Settings...................................................................................................................... 15 Scan Mode ....................................................................................................................... 18 APN Management ........................................................................................................... 18 PIN Management ............................................................................................................ 19 SIM Lock .................................................................................................................................. 21 LAN Setting ...................................................................................................................... 22 DMZ Settings ................................................................................................................... 23 Static Route ..................................................................................................................... 24 Firewall .................................................................................................................... 25 Setting Firewall ................................................................................................................ 25 MAC Filtering ................................................................................................................... 26 IP Filtering ....................................................................................................................... 29 URL Filtering .................................................................................................................... 32 Port Forwarding............................................................................................................... 33 UPnP ................................................................................................................................ 36 DoS .................................................................................................................................. 37 5.2 5.3 5.6 VPN ............................................................................................................................................ 37 5.7 IPv6 ............................................................................................................................................ 38 Status ...................................................................................................................................... 38 IPv6 WAN Settings ................................................................................................................... 39 IPv6 LAN Settings .................................................................................................................... 39 5.8 System ....................................................................................................................................... 39 5.8.1 Maintenance .................................................................................................................. 39 Reboot ............................................................................................................................. 39 Reset ................................................................................................................................ 40 Backup Configuration File ............................................................................................... 40 Upload Configuration File ............................................................................................... 41 5.8.2 TR069 ............................................................................................................................. 41 5.8.3 Date & Time ................................................................................................................... 42 5.8.4 DDNS .............................................................................................................................. 44 5.8.5 Diagnosis ........................................................................................................................ 45 Ping .................................................................................................................................. 45 Traceroute ....................................................................................................................... 46 5.8.6 Port Mirror ..................................................................................................................... 47 5.8.7 Syslog.............................................................................................................................. 48 Local ................................................................................................................................ 48 Network ........................................................................................................................... 48 5.8.8 WEB Setting .................................................................................................................... 49 5.8.9 Account .......................................................................................................................... 50 5.8.10 Logout .......................................................................................................................... 51 FAQs ........................................................................................................................................ 52 6 1 Getting Started 1.1 Welcome to the CPE In this document, the LTE (Long Term Evolution) CPE (customer premises equipment) will be replaced by the CPE. Carefully read the following safety symbols to help you use your CPE safely and correctly:

Additional information Optional methods or shortcuts for an action Potential problems or conventions that need to be specified 1.2 Computer Configuration Requirements For optimum performance, make sure your computer meets the following requirements. Item CPU Memory Hard disk Requirement Pentium 500 MHz or higher 128 MB RAM or higher 50 MB available space Operating system Microsoft: Windows XP, Windows Vista, or Windows 7 Display resolution Mac: Mac OS X 10.5 or higher 1024 x 768 pixels or higher Browser Internet Explorer 7.0 or later Firefox 3.6 or later Opera 10 or later Safari 5 or later Chrome 9 or later 1.3 Logging In to the Web Management Page Use a browser to log in to the web management page to configure and manage the CPE. The following procedure describes how to use a computer running Windows XP and Internet Explorer 7.0 to log in to the web management page of the CPE. Connect the CPE properly. 1. Launch Internet Explorer, enter http://192.168.0.1 in the address bar, and press Enter. As shown in Figure 1-1. Figure 0-1 Enter the user name and password, and click Log In. You can log in to the web management page after the password is verified. As shown in Figure 1-2. Figure 0-2 The default user name and password are both admin. If you want to view or configure the CPE more, you should use the super account to log in to the web management page. The default super user name is superadmin, and the password is admin. To protect your CPE from unauthorized access, change the password after your first login. The CPE supports diagnostic function. If you encounter problems, please contact customer service for the specific using method. To ensure your data safety, it is recommended that you turn on the firewall, and conserve your login and FTP password carefully. 2. 3. 4. 2 Overview 2.1 Viewing Current Connection To view the current connection, perform the following steps:

Choose Overview;

In the Current Connection area, view the connection status, such as DL/UL Data Rate and Online time. As shown in Figure 2-1. 2.2 Viewing LTE Status To view the LTE network status, perform the following steps:

1. Choose Overview;

2. In the LTE Status area, view the information about Connect status, Mode, Cell ID, Signal quality and so on. As shown in Figure 2-3. Figure 2-3 2.3 Viewing WAN Status To view the WAN status, perform the following steps:

1. Choose Overview;

2. In the WAN Status area, view the information about Connect Mode, IP, Subnet Mask, DNS Server and so on. As shown in Figure 2-4. Figure 2-4 3 Statistics 3.1 Viewing CPU Usage To view the CPU usage, perform the following steps:

1. Choose Statistics;

2. In the CPU Usage area, view the CPU usage information, such as Current CPU usage, Max CPU usage, Min CPU usage. As shown in Figure 3-1. Figure 3-1 3.2 Viewing Memory Usage To view the memory usage, perform the following steps:

1. Choose Statistics;

2. In the Memory Usage area, view the memory usage information, such as Total memory, Current memory usage, Max memory usage and Min memory usage. As shown in Figure 3-2. Figure 3-2 3.3 Viewing APN List To view the APN list, perform the following steps:

1. Choose Statistics;

2. In the APN List, view the information about APN information. As shown in Figure 3-3. Figure 3-3 3.4 Viewing Throughput Statistics To view the Throughput Statistics, perform the following steps:

1. Choose Statistics;

2. In the Throughput Statistics area, view the throughput statistics, such as APN throughput and LAN throughput. In this area, also you can choose and click the button Reset to empty the throughput statistics. As shown in Figure 3-4. 3. Figure 3-4 3.5 Viewing Device List To view the device list, perform the following steps:

Choose Statistics;

In the Device List area, view the device information which connect to the CPE, such as Device name, Mac address, IP address and Lease time. As shown in Figure 3-5. Figure 3-5 4 Update 4.1 Version Manager This function enables you to upgrade the software version of the CPE to the latest version. It is recommended that you upgrade the software because the new version, certain bugs have been fixed and the system stability is usually improved. Viewing Version Info To view the version info, perform the following steps:

1. Choose Update>Version Manager. 2. In the Version Info area, you can view the product name and software version. As shown in Figure 4-1. Figure 4-1 Version Upgrade To perform an upgrade successfully, connect the CPE to your computer through a network cable, save the upgrade file on the computer, and make sure the CPE is not connected to anything other than a power adapter and the computer. To perform an upgrade, perform the following steps:

1. Choose Update>Version Manager. 2. In the Version Upgrade area, click Browse. In the displayed dialog box, select the target software version file. 3. Click Open. The dialog box choses. The save path and name of the target software version file are displayed in the Update file field. 4. Click Submit. 5. The software upgrade starts. After the upgrade, the CPE automatically restarts and runs the new software version. As shown in Figure 4-2. During an upgrade, do not power off the CPE or disconnect it from the computer. Figure 4-2 4.2 Auto upgrade To perform a ftp auto upgrade successfully, make sure the CPE is connected to the Internet. To perform a ftp auto upgrade, perform the following steps:

Choose Update>Auto upgrade. Enable auto upgrade. If you want to check new firmware after connect to Internet, you need to enable the item of Check new firmware after connect to Internet. Set a ftp address to the Upgrade folder box. Set Version file. Set User name and Password. Set the Interval of checking new firmware. Set Start time. Set Random time. Click Submit. As shown in Figure 4-3. The CPE will automatically upgrade according to the setting. During an upgrade, do not disconnect the power supply or operate the CPE. Figure 4-3 5 Settings 5.1 Viewing the Device Information To view the System Information, perform the following steps:

Choose Settings;

In the System Information area, view the system status, such as Running time. As shown in Figure 5-1. Figure 5-1 Viewing the Version Information To view the Version Information, perform the following steps:

1. Choose Settings;

2. In the Device Information area, view the device information, such as Product name, Product Model, Hardware Version, Software version, UBoot version and CPE SN . As shown in Figure 5-2. Figure 5-2 Viewing LAN Status To view the LAN status, perform the following steps:

Choose Settings;

In the LAN Status area, view the LAN status, such as Mac address, IP address and Subnet mask. As shown in Figure 5-4. Figure 5-4 5.2 Viewing Network Network Mode To set the network mode, perform the following steps:

Choose Network >WAN Settings;

In the Network Mode area, select a mode between NAT and ROUTER;

Click Submit. As shown in Figure 5-5. Figure 5-5 LTE Settings Settings To set the LTE network, perform the following steps:

1. Choose Network >LTE Settings;

2. 3. In the Settings area, you can set the configuration of LTE network;

In the Status area, you can view the LTE network connect status, such as Frequency, RSSI, RSRP, RSRQ, CINR, SINR, Cell ID and so on. As shown in Figure 5-7. Figure 5-7 Connect Method Setting To set the connect method, perform the following steps:

1. Choose Network > LTE Settings;

2. In the Setting area, Select a connect method between Auto and Manual. As shown in Figure 5-8. Figure 5-8 Auto Connect LTE Network To set the CPE automatically connect to the internet, perform the following steps:

1. Choose Network > LTE Settings;

2. In the Setting area, set the connect method as Auto, when the LTE network is ready, the CPE will be connected automaticity. As shown in Figure 5-9. Figure 5-9 Manual Connect Mobile Network To set the mobile network manual connect to the internet, perform the following steps:

1. 2. Choose Network > LTE Settings;

In the Setting area, set the connect method as Manual, when the LTE network is ready, you can set the CPE connect to the LTE network or disconnect from the LTE network. As shown in Figure 5-10. Figure 5-10 Scan Mode To set the lte network scan mode, perform the following steps:

choose Network>Scan mode;

You can choose full mode, a band the CPE supported Click Submit. Setting Frequency (Earfcn) To set the frequency, perform the following steps:

1 Choose Network>Scan Mode. 2 In the Scan Mode area, choose Frequency Lock. 3 In the Frequency Lock area, you can choose a band, then click Add list to choose a Earfcn Number. 4 Click Submit. As shown in Figure 5-11. Figure 5-11 APN Management To set and manage APN, perform the following steps:

Choose Network>APN Management. In the APN Management area, you can set the APN. Choose a APN number which you want to set. In the APN Setting area you can set the APN parameters, such as enable or disable the apn, apn name, username, password and so on. If you want set a APN as default gateway, you should check that is enabled. Click Submit. As shown in Figure 5-12. Figure 5-12 PIN Management To manage the PIN, you can perform the following operations on the PIN Management page:

Enable or disable the PIN verification. Verify the PIN. Change the PIN. Set automatic verification of the PIN. As shown in Figure 5-13 Viewing the Status of the USIM Card To view the status of the USIM card, perform the following steps:

Figure 5-13 1. 2. 3. 4. 1 Choose Network >PIN Management. 2 View the status of the USIM card in the USIM card status field. Enabling PIN Verification To enable PIN verification, perform the following steps:

1 Choose Network >PIN Management. 2 Set PIN verification to Enable. 3 Enter the PIN (4 to 8 digits) in the Enter PIN box. 4 Click Submit. Disabling PIN Verification To disable PIN verification, perform the following steps:

1 Choose Network >PIN Management. 2 Set PIN verification to Disable. 3 Enter the PIN (4 to 8 digits) in the Enter PIN box. 4 Click Submit. Verifying the PIN If PIN verification is enabled but the PIN is not verified, the verification is required. To verify the PIN, perform the following steps:

1 Choose Network >PIN Management. 2 Enter the PIN (4 to 8 digits) in the PIN box. 3 Click Submit. Changing the PIN The PIN can be changed only when PIN verification is enabled and the PIN is verified. To change the PIN, perform the following steps:

1 Choose Network>PIN Management. 2 Set PIN verification to Enable. 3 Set Change PIN to Enable. 4 Enter the current PIN (4 to 8 digits) in the PIN box. 5 Enter a new PIN (4 to 8 digits) in the New PIN box. 6 Repeat the new PIN in the Confirm PIN box. 7 Click Submit. Setting Automatic Verification of the PIN You can enable or disable automatic verification of the PIN. If automatic verification is enabled, the CPE automatically verifies the PIN after restarting. This function can be enabled only when PIN verification is enabled and the PIN is verified. To enable automatic verification of the PIN, perform the following steps:

Choose Network > PIN Management. Set Pin verification to Enable. Set Remember my PIN to Enable. Click Submit. Verifying the PUK If PIN verification is enabled and the PIN fails to be verified for three consecutive times, the PIN will be locked. In this case, you need to verify the PUK and change the PIN to unlock it. To verify the PUK, perform the following steps:

Choose Network> PIN Management. Enter the PUK in the PUK box. Enter a new PIN in the New PIN box. Repeat the new PIN in the Confirm PIN box. Click Submit. SIM Lock If you want to connect a specify network, and the CPE cant connect other network, you can set a SIM lock. To set the SIM lock, perform the following steps:

1. Choose Network>SIM Lock. 2. Enter the PLMN in the PLMN box. 3. Click Submit. As shown in Figure 3-9. Figure 5-3 1. 2. 3. LAN Setting Setting LAN Host Parameters By default, the IP address is 192.168.0.1 with a subnet mask of 255.255.255.0. You can change the host IP address to another individual IP address that is easy to remember. Make sure that IP address is unique on your network. If you change the IP address of the CPE, you need to access the web management page with the new IP address. To change the IP address of the CPE, perform the following steps:

1. Choose Network>LAN Settings. 2. 3. 4. Click Submit. As shown in Figure 5-14. In the LAN Host Settings area, set IP address and subnet mask. In the DHCP Setting area, set the DHCP server to Enable. Configuration the DHCP Server Figure 5-14 DHCP enables individual clients to automatically obtain TCP/IP configuration when the server powers on. You can configure the CPE as a DHCP server or disable it. When configured as a DHCP server, the CPE automatically provides the TCP/IP configuration for the LAN clients that support DHCP client capabilities. If DHCP server services are disabled, you must have another DHCP server on your LAN, or each client must be manually configured. To configure DHCP settings, perform the following steps:

Choose Network Setting > LAN Settings. Set the DHCP server to Enable. Set Start IP address. they must be on the same network segment. 4. Set End IP address. they must be on the same network segment. 5. Set Lease time. This IP address must be different from the IP address set on the LAN Host Settings area, but This IP address must be different from the IP address set on the LAN Host Settings area, but Lease time can be set to 1 to 10,080 minutes. It is recommended to retain the default value. 6. Click Submit. As shown in Figure 5-15. Figure 5-15 If the demilitarized zone (DMZ) is enabled, the packets sent from the WAN are directly sent to a specified IP address on the LAN before being discarded by the firewall. DMZ Settings To set DMZ, perform the following steps:

1. Choose Network > DMZ Settings. 2. 3. 4. Set DMZ to Enable.

(Optional) Set ICMP Redirect to Enable. Set Host address. 5. Click Submit. As shown in Figure 5-18. This IP address must be different from the IP address set on the LAN Host Settings page, but they must be on the same network segment. Figure 5-18 Static Route Add Static Route To add a static route, perform the following steps:

Choose Network Setting>Static Route. Click Add list. Set the Dest IP address and Subnet mask. Select an Interface from the drop-down list. If you select LAN as the interface, you need set a Gateway. Click Submit. As shown in Figure 5-19. Modify Static Route Figure 5-19 To modify an access restriction rule, perform the following steps:

1. Choose Firewall>Static Route. 2. Choose the item to be modified, and click Edit. 3. Repeat steps 3 through 5 in the previous procedure. 4. Click Submit. As shown in Figure 5-20. Figure 5-20 Delete Static Route To delete a static route, perform the following steps:

Choose Firewall>Static Route. Choose the item to be deleted, and click Delete. 5.3 Firewall Setting Firewall This page describes how to set the firewall. If you enable or disable the firewall, you can modify the configuration. To set the firewall, perform the following steps:

Choose Firewall>Firewall Setting. Choose Enable or Disable to modify the configuration. Click Submit. As shown in Figure 5-30. Figure 5-30 If you choose enable the firewall, you can modify the configuration about firewall, such as Mac filter, IP filter, URL filter and so on. If you choose disable, you cant modify any configurations about the firewall. MAC Filtering This page enables you to configure the MAC address filtering rules. Enabling MAC Filter To enable MAC address filter, perform the following steps:

1. Choose Firewall>MAC Filtering 2. 3. Click Submit. As shown in Figure 5-31. Set MAC filtering to Enable. Figure 5-31 Disabling MAC Filter To disable MAC address filter, perform the following steps:

1. Choose Firewall>MAC Filtering 2. 3. Click Submit. As shown in Figure 5-32. Set MAC filtering to Disable. Figure 5-32 Setting Allow access network within the rules To set allow access network within the rules, perform the following steps:

1. Choose Firewall>MAC Filtering. Set Allow access network within the rules. 2. 3. Click Submit. As shown in Figure 5-33. Figure 5-43 Setting Deny access network within the rules To set deny access network within the rules, perform the following steps:

1. Choose Firewall>MAC Filtering. 2. 3. Click Submit. As shown in Figure 5-34. Set Deny access network within the rules. Figure 5-35 Adding MAC Filtering rule To add a MAC filtering rule, perform the following steps:

Choose Firewall>MAC Filtering. Click Add list. Set MAC address. Click Submit. As shown in Figure 5-35. Figure 5-36 Modifying MAC Filtering rule To modify a MAC address rule, perform the following steps:

1. Choose Firewall>MAC Filtering. 2. Choose the rule to be modified, and click Edit. 3. 4. Click Submit. As shown in Figure 5-36. Set MAC address. Figure 5-37 Deleting MAC Filtering rule To delete a MAC address filter rule, perform the following steps:

Choose Firewall>MAC Filtering. Choose the rule to be deleted, and click Delete. As shown in Figure 5-37. Figure 5-38 Data is filtered by IP address. This page enables you to configure the IP address filtering rules. IP Filtering Enabling IP Filtering To enable IP Filtering, perform the following steps:

1. Choose Firewall>IP Filtering. 2. 3. Click Submit. As shown in Figure 5-38. Set IP Filtering Enable. Figure 5-39 Disabling IP Filtering To disable IP Filtering, perform the following steps:

1. Choose Firewall>IP Filtering. 2. 3. Click Submit. As shown in Figure 5-39. Set IP Filtering Disable. Figure 5-310 Setting Allow access network outside the rules To set allow access network, perform the following steps:

1. Choose Firewall>IP Filtering. 2. 3. Click Submit. As shown in Figure 5-40. Set Allow access network outside the rules. 6. 7. 8. Figure 5-11 Setting Deny access network outside the rules To set allow access network, perform the following steps:

1. Choose Firewall>IP Filtering. 2. 3. Click Submit. As shown in Figure 5-41. Set Deny access network outside the rules. Figure 5-12 Adding IP Filtering rule Add an IP address filtering rule, perform the following steps:

1. Choose Firewall>IP Filtering. 2. Click Add list. 3. 4. 5. Set Service. Set Protocol. In the Source IP Address Range box, enter the source IP address or IP address segment to be filtered. In the Source port range box, enter the source port or port segment to be filtered. In the Destination IP Address Range box, enter the destination IP address or IP address segment to be filtered. In the Destination port Range box, enter the destination port or port segment to be filtered. In the Status box, choose a status the rule will be executed. 9. 10. Click Submit. As shown in Figure 5-42. Figure 5-13 Modifying IP Filtering rule To modify an IP filtering rule, perform the following steps:

1. Choose Firewall > IP Filtering. 2. Choose the rule to be modified, and click Edit. 3. Repeat steps 3 through 9 in the previous procedure. 4. Click Submit. As shown in Figure 5-43. Deleting IP Filtering rule Figure 5-14 To delete an IP address filtering rule, perform the following steps:

1. Choose Firewall > IP Filtering. 2. Choose the rule to be deleted, and click Delete. As shown in Figure 5-44. Figure 5-15 URL Filtering Data is filtered by uniform resource locator (URL). This page enables you to configure URL filtering rules. Enabling URL Filtering To enable URL Filtering, perform the following steps:

3. Choose Firewall>URL Filtering. 4. 5. Click Submit. As shown in Figure 5-45. Set URL Filtering to Enable. Figure 5-16 Disabling URL Filtering To disable URL Filtering, perform the following steps:

1. Choose Firewall>URL Filtering. 2. 3. Click Submit. As shown in Figure 5-46. Set URL Filtering to Disable. Figure 5-17 Adding URL Filtering list To add a URL filtering list, perform the following steps:

Choose Firewall>URL Filtering. Click Add list. Set URL. Click Submit. As shown in Figure 5-47. Figure 5-18 Modify URL Filtering list To modify a URL filtering rule, perform the following steps:

1. Choose Firewall>URL Filtering. 2. Choose the rule to be modified, and click Edit. 3. 4. Click Submit. As shown in Figure 5-48. Set URL address. Figure 5-19 Deleting URL Filtering list To delete a URL list, perform the following steps:

1. Choose Firewall>URL Filtering. 2. Choose the item to be deleted, and click Delete. As shown in Figure 5-49. Figure 5-20 Port Forwarding When network address translation (NAT) is enabled on the CPE, only the IP address on the WAN side is open to the Internet. If a computer on the LAN is enabled to provide services for the Internet (for example, work as an FTP server), port forwarding is required so that all accesses to the external server port from the Internet are redirected to the server on the LAN. Adding Port Forwarding rule To add a port forwarding rule, perform the following steps:

Choose Firewall > Port Forwarding. Click Add list. Set Service. Set Protocol. Set Remote port range. The port number ranges from 1 to 65535. Set Local host. Set Local port. The port number ranges from 1 to 65535. Click Submit. As shown in Figure 5-50. This IP address must be different from the IP address that is set on the LAN Host Settings page, but they must be on the same network segment. Figure 5-21 Modifying Port Forwarding rule To modify a port forwarding rule, perform the following steps:

1. Choose Firewall > Port Forwarding. 2. Choose the item to be modified, and click Edit. 3. Repeat steps 3 through7 in the previous procedure. 4. Click Submit. As shown in Figure 5-51. Figure 5-22 Deleting Port Forwarding rule To delete a port forwarding rule, perform the following steps:

Choose Firewall > Port Forwarding. Choose the item to be deleted, and click Delete. As shown in Figure 5-52. Figure 5-23 Access Restriction Figure 5-53 Add Access Restriction To add a access restriction rule, perform the following steps:

1. Choose Security>Access Restriction. 2. Click Add list. 3. 4. 5. 6. 7. Click Submit. Set Access Restriction to Enable. Set Access Restriction Name. Set Device MAC address or IP address. Set Weekdays and time. Modify Access Restriction To modify a access restriction rule, perform the following steps:

1. Choose Security>Access Restriction. 2. Choose the item to be modified, and click Edit. 3. Repeat steps 4 through 6 in the previous procedure. 4. Click Submit. Delete Access Restriction To delete a access restriction rule, perform the following steps:

1. Choose Security>Access Restriction. 2. Choose the item to be deleted, and click Delete. UPnP On this page, you can enable or disable the Universal Plug and Play (UPnP) function. To enable UPnP, perform the following steps:

1. Choose Firewall > UPnP. 2. Set UPnP to Enable. 3. Click Submit. As shown in Figure 5-54. Figure 5-24 DoS On this page, you can enable or disable the Denial of service (DoS) function. 1 Choose Firewall > DoS. 2 Set UPnP to Enable. 3 Click Submit. As shown in Figure 5-55. Figure 5-255 5.6 VPN This function enables you to connect the virtual private network (VPN). To connect the VPN, perform the following steps:

Choose VPN. In the VPN Settings area, enable VPN. Select a protocol from Protocol drop-down list. Enter Username and Password. Click Submit. You can view the status in VPN Status area. As shown in Figure 5-55. Figure 5-55 5.7 IPv6 Status Internet Protocol version 6 (IPv6) is the most recent version of the Internet Protocol (IP). Every device on the Internet is assigned a unique IP address for identification and location definition. The status page shows IPv6 information. As shown in Figure 5-56. Figure 5-56 IPv6 WAN Settings In this page, user can enable or disable IPv6 function. Meanwhile, user can set WAN Connection Type and the type of DNS.As shown in Figure 5-27 Figure 5-57 IPv6 LAN Settings In this page, user can chose the AutoConfiguration Type. As shown in Figure 5-58. Figure 5-58 5.8 System 5.8.1 Maintenance Reboot This function enables you to restart the CPE. Settings take effect only after the CPE restarts. To restart the CPE, perform the following steps:

1. Choose System>Maintenance. 2. Click Reboot. As shown in Figure 5-59. The CPE then restarts. Figure 5-59 Reset This function enables you to restore the CPE to its default settings. To restore the CPE, perform the following steps:

1. Choose System>Maintenance. 2. Click Factory Reset. As shown in Figure 5-60. The CPE is then restored to its default settings. Figure 5-60 Backup Configuration File You can download the existing configuration file to back it up. To do so:

1. Choose System>Maintenance. 2. Click Download on the Maintenance page. 3. In the displayed dialog box, select the save path and name of the configuration file to be backed up. 4. Click Save. As shown in Figure 5-61. The procedure for file downloading may vary with the browser you are using. Figure 5-61 Upload Configuration File You can upload a backed up configuration file to restore the CPE. To do so:

1. Choose System>Maintenance. 2. Click Browse on the Maintenance page. 3. 4. Click Open. 5. The dialog box choses. In the box to be right of Configuration file, the save path and name In the displayed dialog box, select the backed up configuration file. of the backed up configuration file are displayed. 6. Click Upload. As shown in Figure 5-62. The CPE uploads the backed up configuration file. The CPE then automatically restarts. Figure 5-62 5.8.2 TR069 TR-069 is a standard for communication between CPEs and the auto-configuration server (ACS). If your service provider uses the TR069 automatic service provision function, the ACS automatically provides the CPE parameters. If you set the ACS parameters on both the CPE and ACS, the network parameters on the CPE are automatically set using the TR-069 function, and you do not need to set To configure the CPE to implement the TR-069 function, perform the following steps:

other parameters on the CPE. 1. Choose System>TR069. Set acs URL source. There are two methods, such as URL and DHCP. In the ACS URL box, enter the ACS URL address. Enter ACS user name and password for the CPE authentication. To use the CPE to access the ACS, you must provide a user name and password for authentication. The user name and the password must be the same as those defined on the ACS. If you set Periodic inform to Enable, set Periodic inform interval. Set connection request user name and password. 7. Click Submit. As shown in Figure 7-5. 2. 3. 4. 5. 6. Figure 5-63 5.8.3 Date & Time You can set the system time manually or synchronize it with the network. If you select Sync from network, the CPE regularly synchronizes the time with the specified Network Time Protocol (NTP) server. If you enable daylight saving time (DST), the CPE also adjusts the system time for DST. To set the date and time, perform the following steps:

1. Choose System > Date & Time. 2. Select Set manually. 3. Set Local time or click Sync to automatically fill in the current local system time. 4. Click Submit. As shown in Figure 5-64. To synchronize the time with the network, perform the following steps:

Figure 5-64 3. From the Primary NTP server drop-down list, select a server as the primary server for time 4. From the Secondary NTP server drop-down list, select a server as the IP address of the secondary 5. If you dont want to use other NTP server, you need to enable Optional ntp server, and set a 1. Choose System > Date & Time. 2. Select Sync from network. synchronization. server for time synchronization. server IP address. 6. Set Time zone. 7. Click Submit. As shown in Figure 5-65. Figure 5-65 To set DST, perform the following steps:

1. Choose System>Date&Time. Set DST enable. Set Start Time and End Time. 4. Click Submit. As shown in Figure 5-66. 2. 3. Figure 5-66 The CPE will automatically provide the DST time based on the time zone. Dynamic Domain Name Server (DDNS) service is used to map the user's dynamic IP address to a 5.8.4 DDNS fixed DNS service. To configure DDNS settings, perform the following steps:

1. Choose System > DDNS. 2. Set DDNS to Enable. 3. In Service provider, choose DynDNS.org or oray.com. as Host name. 5. Enter User name and Password. 6. Click Submit. As shown in Figure 5-67. 4. Enter Domain name and Host name. For example, if the domain name provided by your service provider is test.customtest.dyndns.org, enter customtest.dyndns.org as Domain name, and test Figure 5-67 5.8.5 Diagnosis Ping do so:

If the CPE is not functioning correctly, you can use the diagnosis tools on the Diagnosis page to preliminarily identify the problem so that actions can be taken to solve it. If the CPE fails to access the Internet, run the ping command to preliminarily identify the problem. To Enter the domain name in the Target IP or domain field, for example, www.google.com. Choose System>Diagnosis. In the Method area, select Ping. Set Packet size and Timeout. Set Count. Click Ping. As shown in Figure 5-68. Wait until the ping command is executed. The execution results are displayed in the Results box. Figure 5-68 If the CPE fails to access the Internet, run the Traceroute command to preliminarily identify the Traceroute problem. To do so:

Choose System>Diagnosis. In the Method area, select Traceroute. Set Maximum hops ad Timeout. Click Traceroute. As shown in Figure 5-69 1. 2. 3. 4. 5. box. Enter the domain name in the Target IP or domain field. For example, www.google.com. Wait until the traceroue command is executed. The execution results are displayed in the Results 1. 2. 3. 4. 5. Figure 5-69 Port mirroring is used on a network switch to send a copy of network packets seen on one 5.8.6 Port Mirror switch port.To do so:

Choose System>Port Mirror. Enable Port Mirror. Select the WAN Interface which you want a copy. Type the Monitor IP, where the copy will send to. Click Sbumit. As shown in Figure 5-70. Figure 5-70 The syslog record user operations and key running events. 5.8.7 Syslog Local To set the syslog to local, perform the following steps:

1. Choose System>Syslog. 2. 3. In the Setting area, set the method to Local. In the Level drop-down list, select a log level. 4. Click Submit. As shown in Figure 5-71. Figure 5-71 Viewing local syslog To view the local syslog, perform the following steps:

In the Keyword box, set a keyword. Click Pull, the result box will display. Network To set the syslog to network, perform the following steps:

1. Choose System>Syslog. 2. In the Setting area, set the method to Network. In the Level drop-down list, select a log level. In the Forward IP address box, set a IP address. 5. Click Submit. As shown in Figure 5-72. The syslog will transmit to some client to display through network. Figure 5-72 5.8.8 WEB Setting To configure the parameters of WEB, perform the following steps:

1. Choose System> WEB Setting. 2. Set HTTP enable. If you set HTTP disable, you will cant login the web management page with the HTTP protocol from WAN side. Set HTTP port. If you want to change the login port, you can set a new port in the box, the default HTTP port is 80. Set HTTPS enable. If you want to login the web management page with the HTTPS protocol from WAN side, you need to enable the HTTPS. If you want to login the web management page form the WAN, you need to Enable Allowing login from WAN. Set the HTTPS port. 6. 7. Click Submit. As shown in Figure 5-73. 3. 4. 3. 4. 5. Figure 5-73 5.8.9 Account This function enables you to change the login password of the user. After the password changes, enter the new password the next time you login. To change the password, perform the following steps:

1. Choose System>Account. 2. Select the user name, if you want to change the password of normal user, you need to set Enable User enable. 3. Enter the current password, set a new password ,and confirm the new password. 4. New password and Confirm password must contain 5 to 15 characters. 5. Click Submit. As shown in Figure 5-74. Figure 5-74 5.8.10 Logout To logout the web management page, perform the following steps:

Choose System and click Logout It will back to the login page. 6 FAQs The POWER indicator does not turn on. Make sure that the power cable is connected properly and the CPE is powered on. Make sure that the power adapter is compatible with the CPE. Fails to Log in to the web management page. Make sure that the CPE is started. Verify that the CPE is correctly connected to the computer through a network cable. If the problem persists, contact authorized local service suppliers. The CPE fails to search for the wireless network. Check that the power adapter is connected properly. Check that the CPE is placed in an open area that is far away from obstructions, such as concrete or wooden walls. Check that the CPE is placed far away from household electrical appliances that generate strong electromagnetic field, such as microwave ovens, refrigerators, and satellite dishes. If the problem persists, contact authorized local service suppliers. The power adapter of the CPE is overheated. The CPE will be overheated after being used for a long time. Therefore, power off the CPE when you are not using it. Check that the CPE is properly ventilated and shielded from direct sunlight. The parameters are restored to default values. If the CPE powers off unexpectedly while being configured, the parameters may be restored After configuring the parameters, download the configuration file to quickly restore the CPE to the default settings. to the desired settings. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by BTI could void the users authority to operate the equipment. FCC Radiation Exposure statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 50cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

1257019101000293 Product Name: LTE Outdoor CPE FCC IDWBKCP880-B Grantee Code WBK Model Name: CP880-B S/N1257019101000293 MAC : A893520B2210 IMEI : 860524031927237 Frequency BandBand 48 Supply Voltage24VDC ManufacturerBravo Tech Inc

SGS North America Inc. j j 620 Old Peachtree Road Applicant Declaration SUITE 100 Suwanee, Georgia 30024 United States

| Appleant Legal Business Name BTI Wireless |

Address 6185 Phyllis Drive #D, Cypress, California 90630, United States Granee Code WBK FCCD WBKCP880-B Richard Xu

+1-214-850-1676 richard.xu@btiwireless.com Auithaized Contact Name Centzct Email Centect Phone

|, the undersigned, certify that | am an authorized signatory for the Applicant and therefore declare;

) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. t) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

(1) labeling the equipment with the exact FCC ID as specified in this application,

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, Cc) ifthe Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing.

(2) the Applicant shal/ make provisions to always have a production sample available upon request by SGS, FCC and/or ISED.

(3) the Applicant shal/, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https:/Awww.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-requlations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.htm!

Applicant ie -

schar Xu Print Name: | Richard Xu Title: COO

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Applicant Declaration Rev:0.0

BTI Wireless Date: 23/07/2020 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC Jp: WBKCP880-B

, including signing of g to these matters. Any and all acts carried out effect as acts of our own. Print Name: Richard Xu Signature: Richard o On behalf of Company: BTI Wireless Telephone: +1-214-850-1 676 E-mail: richard.xu@btiwireless.com

TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Schematic(s) Block Diagrams Operational Descriptions Tune Up Procedure Sincerely, Print Name: Richard Xu Signature: Sait Xu On behalf of Company: BTI Wireless Telephone: +1-214-850-1676 E-mail: richard.xu@btiwireless.com BTI Wireless Title:COO