oe CBUFFALO _ssmewiznesmewi2ie-r Instruction Manual Precautions for Use
+ Keep the sensor part of the mouse clean, and prevent it from gelting damage Please note that the batteries will drain faster if the mouse button is held down for long periods, or if the mouse is moved continually Turn the power OFF when carrying the mouse in a bag or pouch. Safety Precautions for Using the Blue LED Optical Mouse The Blue LED optical sensor is extremely sensitive, but it may have difficulty operating or may not be able to operate on shiny, blue colored, or intensely colored or patterned surfaces Also, depending on the conditions in which the mouse is used, dust may collect around the lens area, reducing the sensitivity of the sensor. In this case, use an air duster etc. to remove the dust. Precautions with Regards to Radio Waves
* Do not use this product in the following places. Near a microwave oven where magnetic field, static asd or radio disturbance occurs. In the vicinity of objects using waves of approximately 2.4GHz (the radio waves may not reat depending on the environment.)
+ This product uses the same radio channel frequency as the following equipment and wireless stations.
+ Industrial, scientific and medical equipment.
= Wireless stations for mobile object identification used in factory production lines. 1 In-plant wireless stations (license required) 2 Specified low power wireless stations (license not required)
* Follow the instructions below to prevent this product from interfering with the equipment or wireless stations listed above. 1. Make sure there are no in-plant wireless stations or specified low power wireless stations for mobile object identification operating in the vicinity before using this product. 2. Should this product cause radio wave interference with an in-plant wireless station for mobile object identification. immediately change the lacation where this product is used, or stop radio wave emission ta avoid radio wave interference, 3. Please contact our Technical Support Center for any ather problems such as radio wave interference with a specified low power wireless station for mobile object identification caused by this product. Frequency Band | 2 4GHz_ Modulation FSK Assumed 10m or less interference range Entire bandwidth is being used, and use of Availabilty off same bandwidth as the in-plant frequency change | wireless station or specified low pow!
wireless station is unavoidable. C Check'the Package Contents ) C How/to)|Use\this) Product ) C ProductSpecifications )
@ Mouse (main unit) 1 1. Connect the receiver to a USB port on the computer. =i. ee ie 2. Turn the power switch of the unit on ieee USs Wheel button |, | Sensor Blue LED optical sensor D ce et cor j inn Section later in the _ USB Port for
<< recharging seroll the pag Right button
@Receiver 1
@ Instruction manual
(this document) 1 How. to)Recharge this Product Please recharge this product before use.
@ USB cable for recharging (6.5cm) 1
@ USB cable for recharging (1.0m) 4 2 Tum the computer power on Connect the supplied USB cable for recharging to the recharging port on this product, and connect the other side to a USB cort on the computer. 3) The LED indicator lights when recharging starts. When recharging is complete, the LED indicator goes out Remove the USB cable for recharging 3 This product can be used during recharging, Note The unit is now ready for use. Bs is product is shipped with the mouse and receiver already connected, you co not need to connect them Radio wave frequency 2.4GHz
<About the Scroll Wheel>
Simply swipe your finger up or down the LED indicator section to scroll the page. This LED indicator is used in the same way as a physical scroll wheel Carrying|the Receiver, There is storage space for the receiver in the USB port for recharging on the rear of the mouse. The receiver can be stored for convenience when carrying the unit around LED Indicator, Status LED Indicator Flashes for approx. When the battery level is low | 10 seconds when the mouse is moved and the cursor stops. Lights during recharging. and goes out when recharging is complete,
( Sleep) Mode ) During recharging DB Onlyuse the Froid US cable charg to recharge this device. Never use a different cable or caution recharging device o rocharge this product, 2s dolig So is dangerous. Correct operation cannot be guaranteed when a different cable or recharging device is used The unit enters sleep mode after approximately 10 minutes. Press one of the buttons to resume operation, Radio)Wave Range
+ Nonmagnetic material (wooden desk etc.) => Approx. 10m
+ Magnetic material (steel desk etc.) = Approx. 3m
* Values are obtained via our in-house tests and are not guaranteed values. Resolution 1000dpi Compatible devices Wincows computers Mouse dimensions Approx. W50 x D82 x H23mm Mouse weight Approx. 47g Receiver dimensions __Approx. W13.9 x D31.7 x H9.7mm Receiver weight Approx. 2a Operating Environment Temperature 5C 40C. humidity 5% - 90% (no condensation) Product Contents, Mouse, receiver, 2 cables for recharging, instruction manual Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions. may cause harmful interference to racio communications. However, there is no guarantee that interference will nat occur in a particular instalation. if cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
+ Reorient or relocate the receiving antenna,
+ Increase the sesaration between the equipment and receiver.
* Connect he equipment ino an allt ona ret eiferent fram tht to which the receiver is cont
+ Consult the dealer or an crperenced radiofTV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This devioe may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment BD Allabove procedures are based on the Japanese version of the OS. Procedures may vary depending Caution on the OS used.