BSMBW02 / BSMBW02R Instruction Manual Multilanguage Manual Precautions for Use Keep the sensor part of the mouse clean and prevent it from getting damaged. Please note that batteries will drain faster if the mouse button is held down for long periods, or if the mouse is moved continually. Turn the power OFF when carrying the mouse in bag or pouch. Safety Precautions for Using the 2.4GHz Wireless Mouse The BlueLED optical sensor is extremely sensitive. However, due to its nature, it may have difficulty operating or may not be able to operate at all on highly reflective shiny surfaces, or intensely colored or pattern surfaces. Depending on the usage environment, dust collect around the sensor and reduce the sensitivity of the sensor. In this case, use an air duster etc. to remove the dust. Precautions with Regards to Radio Waves Do not use this product in the following places:
Near a microwave oven where magnetic field, static electricity or radio disturbance occurs. In the vicinity of objects using radio waves of approximately 2.4 GHz (the radio waves may not reach depending on the environment.) This product uses the same radio channel frequency as the following equipment and wireless stations:
Industrial, scientific, and medical equipments Wireless stations for mobile object identification used in factory production lines
(1) In-plant wireless station (license required)
(2) Specified low power wireless station
(license not required) Follow the instructions below to prevent this product interfering with the equipment or wireless stations listed above:
BSMBW02 / BSMBW02R
. OFF . 2.4GHz LED .
. 2.4 GHz
(1) ( )
(2) ( )
BSMBW02 / BSMBW02R OFF 2.4GHz BlueLED
2.4 GHz
(1)
(2) 1. 2. BSMBW02 / BSMBW02R OFF 2.4GHz BlueLED
2.4 GHz
(1)
(2) 1. 2. In some applications, "Forward" and
"Back" operations cannot be used. Caution Receiver 1 AAA alkaline batteries 2 For operation check Instruction manual (this document) 1 How to Use this Product How to Use this Product 1. Open the battery box cover on the back of the unit. Please take care not to hurt your fingernails or fingers etc. when opening the battery box cover. Caution 2. Insert the AAA batteries so that the Battery removal sheet lies underneath the batteries. Make sure the polarity is correct. 3. Close the battery box cover. 4. Turn the power switch of the unit ON. 5. Connect the receiver to a USB port on your computer. When this unit is connected to a computer while it is switched ON, the driver is automatically installed and the unit becomes ready for use. Note As this product is shipped with the mouse and receiver already connected, you do not need to connect them. However, if the mouse response is poor due to the influence of a wireless LAN etc., perform the connection process.
<Connection Process>
With the mouse turned ON, place it approximately 15 cm from the receiver that is connected to a USB port on the computer, and press the Connect button on the back of the mouse. The battery indicator lights red. When the connection process is completed, the light goes off. When the mouse pointer moves correctly, the connection process is completed.
<Attention>
This mouse can only be used with the supplied receiver. Should the receiver be lost, the unit cannot be used with a different receiver even if it is from the same model. Be careful handling the receiver as it is very small. The receiver can be stored inside the mouse. The receiver can be stored inside the mouse. For the convenience when carrying around the unit, the receiver can be stored in the back of the mouse. Slide the receiver into the indentation on the back of the mouse for storage. Battery Indicator Battery Indicator 1. When the unit is turned ON with sufficient battery level, the battery indicator lights red for approx. 3 seconds and then goes off. 2. When the battery level is low, the battery indicator flashes red. When the battery indicator flashes red, replace the batteries. If you do not intend to use the unit for a long time, or intend to carry the unit, turn the power switch OFF to save batteries. Note Radio Wave Range Radio Wave Range Nonmagnetic material (wooden desk etc.) approx. 10 m Magnetic material (steel desk etc.) approx. 3 m Values are obtained via our in-house tests and are not guaranteed values. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Caution All above procedures are based on the Japanese version of the OS. Procedures may vary depending on the OS used.
"" . 1 AAA 2
( ) 1
. 1. Make sure there are no in-plant wireless stations or specified low power wireless stations for mobile object identification operating in the vicinity before using this product. 2. Should this product causes radio wave interference with an in-plant wireless station for mobile object identification, immediately change the location where this product is used, or stop radio wave emission to avoid radio wave interference. 3. This product is equipped with a function that automatically avoids radio wave interference. If the product still causes radio wave interference, stop using it immediately. 4. Please contact our Technical Support Center for any other problems such as radio wave interference with a specified low power wireless station for mobile object identification caused by this product. Frequency band Modulation Assumed interference range Advisability of frequency change 2.4GHz GFSK 10 m or less Entire bandwidth is being used, and use of the same bandwidth as the "in-plant wireless station" or "specified low power wireless station" is unavoidable Check the Package Contents Check the Package Contents Mouse (main unit) 1 Battery indicator Battery level and connection process status can be checked using the red lit or flashing LED lamp. Scroll wheel Right button Left button
"Back" button Goes back to the previous page.
"Forward" button Goes to the next page.
"Forward" and "Back" operations can be used with Web browser and other applications. 1. 2. 3. 4. 2.4GHz GFSK 10 m
() 1 LED
. 1. . 2. AAA
. 3. . 4. ON . 5. USB
. ON
. , LAN
ON USB 15 cm ,
. 1. ON 3
. 2. OFF
( ) 10 m
( ) 3 m
(B)
. OS
. OS
. 3. 4. 2.4GHz GFSK 10 m 1 LED 1 AAA 2 1 3. 4. 2.4GHz GFSK 10 m 1 LED 1 AAA 2 1 1. 2. AAA 3. 4. ON 5. USB ON
ON USB 15 cm
1. ON 3 2. OFF 10 m 3 m
(Pb)
(Hg)
(Cd)
(Cr+)
(PBB)
(PBDE) SJ/T 11363-2006 SJ/T 11363-2006 1. 2. AAA 3. 4. ON 5. USB ON
ON USB 15 cm
1. ON 3 2. OFF 10 m 3 m
+DC 3V 2.4GHz NCC