User Manual User Manual AirStation WLI-U2-KG125S Wireless 54 Mbps USB Adapter with Antenna Interface WLI2-USB-G54 www.buffalotech.com v1.0 Introduction Congratulations on your purchase! The AirStation WLI-U2-KG125S Turbo G wireless USB 2.0 Adapter connects your notebook computer or desktop PC to a 2.4ghz 802.11g or b network. System Requirements A compatible G or B band access point. A PC running Windows XP, 2000, ME, or 98se that has a USB 2.0 port. Package Contents WLI-U2-KG125S USB Adapter Utility CD with Manual Quick Setup Guide Warranty Statement 2 Table of Contents Getting Started ................................................................ 4 Installing Drivers .............................................................. 5 Installing with Windows XP ............................................. 7 Installing with Windows 98, Me, 2000 ............................ 8 Installing Client Manager ............................................ 11 Using Client Manager .................................................. 14 AOSS .............................................................................. 21 Wireless Zero Con g ..................................................... 25 Speci cations................................................................ 28 Troubleshooting/FAQ ................................................... 29 FCC/CE Information ..................................................... 32 Contact Information ..................................................... 50 3 Getting Started 1. Installing Drivers:
Insert the AirNavigator CD into the CD-ROM drive of the PC. Do not insert the USB key into a USB port yet. If setup.exe does not launch automatically, click Start and select Run. Enter D:\Setup.exe in the Open eld, where D: is the letter assigned to your CD-ROM. Click OK to launch the wizard. 4 AirNavigator Select Install Wireless Drivers. Click Next. 5 AirNavigator - Installing Drivers The Software License Agreement will appear. Select Agree and then click Next. If you have Windows XP on your PC, turn to page 7 to install your adapter. If you are using Windows 98se, Me, or 2000, turn to page 8. 6 Installing with Windows XP 2. Installing the Wireless USB Adapter with Windows XP*:
Plug the Wireless USB Adapter or stand into an available USB port on your PC. The Found New Hardware Wizard will launch automatically. If this screen doesnt appear, remove the Wireless USB Adapter and restart the notebook. Reinsert the Wireless USB Adapter once the notebook has rebooted. If the wizard doesnt run automatically, select Install the software automatically, and click Next, then Finish.
* If youre using Windows 98se, Me, or 2000, turn to page 8 for alternate instructions. 7 Installing with Windows 98/ME/2000 2. Installing the Wireless USB Adapter with Windows 98se/Me/2000:
1. Installing the Wireless USB Adapter:
Power on the notebook PC and let it boot into Windows. Plug the Wireless USB Adapter into an available USB port on your PC. The Found New Hardware Wizard will launch automatically. If this screen doesnt appear, remove the Wireless USB Adapter and restart the notebook. Reinsert the Wireless USB Adapter once the notebook has rebooted. Select Install the software automatically. Click the Next button. 8 Installation / Setup Insert the AirNavigator CD. Click Next at the Welcome to the Found New Hardware Wizard. Select Search for a suitable driver for my device. Click Next to continue. Check only the CD-ROM drives checkbox, and clear any other checkboxes that are selected. Click Next to continue. 9 Installation / Setup Windows will display a driver you can use with the Wireless USB Adapter. Click Next. In Windows 2000, if the Digital Signature Not Found page opens as shown, click Yes to continue the installation process. When the Wireless USB Adapter is successfully installed, click Finish. Restart your computer if prompted. See the next page to install the Client Manager. 10 Client Manager 3. Installing Client Manager Client Manager lets you con gure your wireless network, survey and connect to available access points, enable and use WEP encryption, initiate AOSS, and create connection pro les. Note: During Installation, Client Manager disables Windows XPs Zero Con guration Tool. If you have Windows XP, and you dont want to install or use Client Manager, turn to page 25 to use the built in Windows Zero Con guration Tool instead. Insert the AirNavigator CD. The AirNavigator dialog box should open automatically. If it does not, click Start, then Run, and enter D:\Setup.exe in the Open eld, where D: is the letter assigned to your CD-ROM drive. Click the OK button. Select Install Client Manager to launch the InstallShieldWizard. 11 Client Manager Once the Installer Wizard launches, click the Next button to begin the software installation. Press I Agree to accept the license agreement and continue the installation process. 12 Client Manager Press the OK button to nish and close the installation program. Press the Exit Setup button to close the AirNavigator installation utility. The Buffalo Client Manager is now installed and running; clicking on its icon (the black antenna icon) will allow you to begin using it. 13 Client Manager Con guration You may use Client Manager to con gure your wireless network manually. Client Manager consists of the Status page, the Survey page, and the Pro les page. You can access each page by clicking the corresponding button at the top of Client Manager. Several dialog boxes are also available. You can access the Edit Pro le dialog box, New Pro le dialog box, IP Con guration dialog box, or WEP Con guration dialog box using the Client Manager pages. You may also initiate AOSS (page 21). Status Page Click Status to open this page. By default, this page is displayed when you start Client Manager. Details of connection status are displayed. This page only displays connection information; no changes to settings are made here. This page includes the following components:
Adapter Name Displays the part number of the wireless adaptor that is being used. 14 Manual Con guration - Status Page Network Type Displays whether network is in Ad-Hoc or Infrastructure mode. Rate The speed of communication between wireless devices. If the Client Manager is not connected to a remote wireless device (access point or another client), no rate will be displayed. Channel The channel that the two wireless clients are using for communication. If the Client Manager is not connected to a remote wireless device, no channel will be displayed. Channels 1-11 may be used. Security The type of encryption in use. If the Client Manager is not connected to a remote wireless device, then No Encryption will be displayed. IP Address The IP address of the machine the Client Manager is installed on. If the Client Manager is not connected to a network with DHCP, then no IP address will be displayed. MAC Address The MAC address of the wireless client device inside the computer Client Manager is installed on. If no wireless device is present in the computer, then no MAC Address will be displayed. Signal Strength Displays the signal strength of the peak signal level the wireless adapter receives from the wireless device to which it is connected. Next to the signal level is the wireless hardware being used for this measurement. 15 Manual Con guration - Scan Page Click the Scan button to open this page. Here, you can survey the area, display available access points, and connect to available access points. This page includes the following components:
SSID The SSID is the name of a wireless network. Each wireless device on a network must use identical SSIDs to successfully communicate. Wireless Mode Displays available modes for each available remote wireless device. Channel Displays the wireless channel used by each available network. Strength Displays the relative signal strength of the wireless networks. Encryption Displays whether the wireless network is using any sort of encryption. Click Connect to connect to a highlighted SSID, or Refresh to update the list of available wireless devices. 16 Manual Con guration - Encryption This dialog will open. If you are not using encryption, just click Connect to connect to your network. If your AP uses encryption, the correct encryption type should already be selected automatically in the Encryption Method drop down list. Only change this setting if necessary. The Encryption Key eld is where the actual key for the wireless network should be entered. Some wireless networks allow you to enter multiple keys; four separate elds are available for this. If your network only uses one encryption key, then please use the rst eld (#1) to enter your key. The Register Pro le option will store this wireless network in your pro les. You will then automatically connect to this network when inside its range. This is recommended if you plan on using this wireless network again. Press the Connect button once you have entered your encryption information. 17 Manual Con guration - Pro les Page Pro les Page Click the Pro les tab to open this page. Use this page to access your pro les. Pro les allow you to save the information associated with a speci c wireless network so you can quickly and easily connect to that network when you are in that location. The Pro les page allows you to add, delete, and edit your pro les, as well as import and export data. Connect Click the Connect button to connect to the selected pro le and return to the Status page. Edit Click the Edit button to edit the selected pro les settings. The Edit button also allows you to delete pro les that are no longer used or required. Add Click the Add button to add a pro le manually. You will need important information such as SSID, encryption settings, and network type. 18 New Pro le Dialog Box Manual Con guration - New Pro le Select Pro le Select whether the pro le is for a wireless or wired connection. the new pro le. Pro le Name Enter the name you want to associate with Network Type Select the network mode you want to associate with the new pro le. Select Infrastructure if your network consists of both wired and wireless devices that communicate through a central device, such as an access point. Select Ad-hoc if your network consists of only wireless devices that communicate with each other directly. Network Name SSID Enter the SSID of your network. The SSID is the name of your wireless network. All wireless devices on a network must use identical SSIDs to successfully associate with other devices on the network. MYSSID is an example of a valid SSID. Channel Auto-Channel is recommended for most pro les. If you are making an Ad-hoc connection, or connecting to a network that doesnt broadcast its SSID, you may have to set the wireless channel manually here. Encryption Method Displays the types of encryption available. Once encryption is selected, you will be required to enter an Encryption Key. For the Transmission Key Number, 1 is recommended. OK Click OK to save your speci cations and return to the Pro les page. 19 Manual Con guration - Advanced Pro le Options Advanced Pro le Options Network Tab Displays the network information tab. A static IP can be speci ed for this wireless pro le here. It is not recommended to change any of these settings unless speci ed by an administrator. Browser Tab Displays settings to change your browser preferences for this wireless pro le. A speci c home page can be speci ed when connected to this wireless pro le as can speci c proxy server addresses. Printers Tab Displays the printers tab. A speci c default printer can be associated to this pro le. Thus, when connected to this pro le, a speci c printer will be used as the default printer. OK Click the OK button to save your speci cations and return to the Pro les page. AOSS Icon To automatically add the USB wireless client to your network, just click this icon and then hold down the AOSS button on your wireless router for a few seconds. Turn to the next page for more on using AOSS. 20 Using AOSS AOSS (AirStation One-Touch Secure System) is a simple system for connecting wireless clients to an access point while enforcing the most secure possible connection encryption type. Users no longer need to worry about choosing the proper security protocols, IP addresses, or SSID. AOSS determines the optimal connection and con gures itself in seconds. Your router or access point must support AOSS to use it. Your WLI-U2-KG125S has its AOSS button in the Client Manager 3 software. If your router or access point supports AOSS, then AOSS will let you connect the WLI-U2-KG125S to your wireless network, easily and securely. Start Client Manager by double clicking on the black antenna icon in your System Tray, or by launching the Client Manager from your Start Menu:
Programs >> Buffalo >> AirStation Utility >> Client Manager. 21 Using AOSS From the Status Screen, select the Pro les tab. Initiate AOSS by clicking the blue AOSS button on the Client Managers screen. The AOSS wizard will appear. Now, press the AOSS button on your access point. Hold it down until the AOSS LED on the access point begins to ash (1-3 seconds). 22 Using AOSS Once AOSS is complete (about 30 seconds), the connection is archived as a pro le for later use. To minimize Client Manager to the system tray, click the X in the top right corner. Notes:
AOSS will scan for an AOSS partner for about two minutes. If it times out before nding one, just press the AOSS buttons again. Output power is reduced to 25% of normal during AOSS for security reasons. If youre having trouble making an AOSS connection, temporarily move the devices closer together. AOSS will automatically use the highest level of security available for all currently connected wireless devices. If you have trouble connecting with AOSS, temorarily disable all personal rewalls on your PC, such as ZoneAlarm or Microsoft Personal Firewall. These programs may be re-enabled after AOSS has nished. Also, make sure that any other wireless client manager software (including Windows XPs Zero Con guration Service) is disabled before using Client Manager 3. 23 Wireless Zero Con guration Wireless Zero Con guration Service (Windows XP) Windows XP offers the Wireless Zero Con guration Service to support 802.11a, 802.11b and 802.11g wireless networking. This service automatically polls the area for available wireless access points. If an available wireless access point is found, Windows attempts to connect to the access point. If no available wireless access points are found, you must manually add the access points. Note: The Wireless Zero Con guration Service and Client Manager do not function properly together. If you want to use Client Manager, disable the Wireless Zero Con guration Service. Enabling the Wireless Zero Con guration Service Select StartControl PanelAdministrative ToolsServices to open the Services window. Select Automatic in the Startup Type eld of Wireless Zero Con guration Service to enable the Wireless Zero Con guration Service. Note: Windows XPs default setting for Wireless Zero Con guration Service is Automatic
(on). Disabling the Wireless Zero Con guration Service Select StartControl PanelAdministrative ToolsServices to open the Services window. Select Disabled in the Startup Type eld of Wireless Zero Con guration Service to disable the Wireless Zero Con guration Service. 24 Wireless Zero Con guration Using Wireless Zero Con guration:
Normally, Windows XP will scan for available wireless access points once the Wireless Notebook Adapter is installed. If Windows detects an access point, a networking icon appears on the task bar. One or more wireless networks are available appears as a caption accompanying the icon. Notes: If Wireless Zero Con guration is not running, click Start>Control Panel>Administrative Tools>Services. Select Automatic in the Startup Type eld of the Wireless Zero Con guration Service to start it. If you dont want to use Wireless Zero Con g and would rather use Buffalos client utility, or if you have a Windows 98 or 2000 computer, turn to page 11. Right click the networking icon in the taskbar and select View Available Wireless Networks to display a list of available wireless networks. Select a network and click Connect. If the network that you are connecting to is unsecured, you may need to check the box allowing you to connect to an unsecured network. 25 Connecting Click the Advanced button to enter an SSID network name or WEP/WPA encryption key manually. To add an SSID network name that is not listed, click the Add button. 26 Connecting To enter an encryption key, select the appropriate wireless network and click the Con gure button. From the pull down menu, select the appropriate type of Data encryption for the wireless network. Enter and con rm the Network Key (encryption key). Click the OK button when nished. 27 Wireless LAN Interface Standards Compliance Communication Protocol Frequency Range Transmission Rate Access Mode Security Others Interface Power Consumption Environmental Operation Dimensions OS Support Speci cations IEEE802.11g, IEEE802.11b Direct Sequence Spread Spectrum
(DS-SS), Half Duplex 2.412-2.472Ghz 802.11g: 1, 2, 5.5, 11, 18, 24, 36, 48, 54Mbps 125* Mode: 13, 20, 27, 40, 54, 80, 110, 125Mbps Infrastructure mode, Ad-Hoc mode 128/64 Bit WEP, WPA, 802.1x, WPA-PSK, TKIP, AES USB 2.0 (Compatible USB 1.1) 460mA (max) 0-55C, 20-80% (non-condensing) 4.1 x 1.1 x 0.5 inches (103 x 29 x 12 mm) Windows XP, 2000, Me, 98se 28 Troubleshooting / FAQ Use this section to locate answers to frequently asked questions. What should I do if I already have a version of Client Manager on my PC?
Update your Client Manager to the version on the CD. If you do not update your Client Manager, there could be a loss of functionally, as some versions of Client Manager will not work properly with the Wireless USB Adapter. Before updating Client Manager, you must uninstall all previous versions of Client Manager. To update your Client Manager, load the Air Navigator CD and select Install Client Manager. Why won't all my network clients work?
Some operating systems support only a limited number of network clients. Windows 98/Me: These operating systems support only four network clients. If you install more than four network clients, only the rst four clients you install will work. Will Client Manager support all operating systems?
Client Manager and the AirStation Wireless USB Adapter currently support only Windows 98/ME/2000/XP. They do not currently support Windows NT, Mac OS, or Linux. 29 Troubleshooting / FAQ Why won't Client Manager function properly?
In Windows XP, the Wireless Zero Con guration Service con icts with Client Man-
ager. Normally, Zero Con g is disabled when Client Manager is installed, but other software may turn it back on. You may disable Wireless Zero Con g manually. Click StartControl PanelAdministrative ToolsServices to open the Services window. Select Disabled in the Startup Type eld of Wireless Zero Con guration Service to disable the Wireless Zero Con guration Service. I have more than one Air Navigator CD. Do I need more than one CD?
No. You receive the same Air Navigator CD with each Buffalo Technology access point and wireless adapter. Just use the most recent CD for installing any Buffalo Technology wire-
less products. 30 54/125* Disclaimer
* 54 Mbps is the maximum wireless signal rate derived from IEEE Standard 802.11a and 802.11g speci cations. 125 Mbps is the maximum wireless signal rate derived from using channel bonding technology when used with supported devices. Actual data throughput will vary depending upon network conditions and environmental factors, including volume of network traf c, building materials and construction, and network overhead. 31 FCC / CE Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 32 FCC / CE Information IMPORTANT NOTE:
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device complies with FCC RF Exposure limits set forth for an uncontro-
lled environment, under 47 CFR 2.1093 paragraph (d)(2). This transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter. This equipment has been SAR-evaluated for use in laptops (notebooks) with side slot conf iguration. R&TTE Compliance Statement This equipment complies with all the requirements of the DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity
(R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000. Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this manual and of 33 FCC / CE Information the computer manufacturer must therefore be allowed at all times to ensure the safe use of the equipment. EU Countries intended for use The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland, France (with Frequency channel restrictions), Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Norway, The Netherlands, Portugal, Spain, Sweden, Switzerland and United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states Iceland, Liechtenstein, Norway and Switzerland. EU Countries Not intended for use None. Potential restrictive use France: Only channels 10,11,12, and 13. 34 Federal Communication Commission Declaration of Conformity ( DoC ) Statement Model No: WLI-U2-KG125S AirStation High Power Dual A+G SmartRouter Buffalo Inc. 15, Shibata Hondori 4-chrome Minami-ku, Nagoya 457-8520 Japan 01181-52-241-7980 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by 35 one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Caution:
Any changes or modi cations not expressly approved by the party responsible for product compliance could void the users authority to operate the equipment. Within the 5.15-to-5.25-GHz band, UNII devices are restricted to indoor operations to reduce any potential for harmful interference to co-channel Mobile Satellite Systems (MSS) operations Caution:
Exposure to radio frequency radiation ( below is for portable device ) To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. 36 Caution Exposure to radio frequency radiation (below is for portable device) To comply with FCC RF exposure compliance requirements, this device must not be colocated or operating in conjunction with any other antenna or transmitter. b. Industry Canada Portion Canada Regulatory Compliance Statement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numriqu de la classe B est conform la norme NMB-003 du Canada. For Customers in Canada This device complies with RSS 210 of Industry Canada (IC). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of this device. L utilisation de ce dispositif est autorise seulement aux conditions suivantes :
(1) il ne doit pas produire de brouillage et
(2) l utilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. 37 Caution: Within the 5.15-to-5.25-GHz band, UNII devices are restricted to indoor operations to reduce any potential for harmful interference to co-channel Mobile Satellite Systems (MSS) operations Exposure to radio frequency radiation (below statement applied to mobile or portable device) The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF eld in excess of Health Canada limits for the general population;
consult Safety Code 6, obtainable from Health Canadas website at www.hc-sc.gc.ca/rpb. c. EU Portion European Community Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC The following standards were applied: (Omni) Radio: EN 300-328 v1.6.1 (2.4-GHz operation) WLI-U2-KG125S is 2.4GHz product. EMC: EN 301.489-1 v1.4.1, EN 301.489-17 v1.2.1 Safety: IEC 60950 ( 1999 3rd Edition with Amend. 1,2,3,4 ) & EN 60950 ( 2000 ) The following CE mark is af xed to the device:
38 Note: This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact your customer service representative. To comply with RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Member States shall ensure that the manufacturer or the person responsible for placing the apparatus on the market provides information for the user on the intended use of the apparatus, together with the declaration of conformity to the essential requirements. Where it concerns radio equipment, such information shall be suf cient to identify on the packaging and the instructions for use of the apparatus the Member States or the geographical area within a Member State where the equipment is intended to be used and shall alert the user by the marking on the apparatus referred to in Annex VII, paragraph 5, to potential restrictions or requirements for authorization of use of the radio equipment in certain Member States. 39 Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC esky
[Czech]
Buffalo Technology Inc. tmto prohlauje, e tento AirStation WLI-U2-KG125S je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 1999/5/ES. Dansk
[Danish]
Undertegnede Buffalo Technology Inc. erklrer herved, at flgende udstyr AirStation WLI-U2-KG125S overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF. Deutsch
[German]
Hiermit erklrt Buffalo Technology Inc. dass sich das Gert AirStation WLI-U2-KG125S in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 1999/5/EG be ndet. Eesti
[Estonian]
Kesolevaga kinnitab Buffalo Technology Inc. seadme AirStation WLI-U2-KG125S vastavust direktiivi 1999/5/
E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. English Hereby, Buffalo Technology Inc. declares that this AirStation WLI-U2-KG125S is in compliance 40 with the essential requirements and other relevant provisions of Directive 1999/5/EC. Espaol
[Spanish]
Por medio de la presente Buffalo Technology Inc. declara que el AirStation WLI-U2-KG125S cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
[Greek]
Buffalo Technology Inc. AirStation WLI-U2-KG125S 1999/5/. Franais
[French]
Par la prsente Buffalo Technology Inc. dclare que lappareil AirStation WLI-U2-KG125S est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano
[Italian]
Con la presente Buffalo Technology Inc. dichiara che questo AirStation WLI-U2-KG125S conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. 41 with the essential requirements and other relevant provisions of Directive 1999/5/EC. Espaol
[Spanish]
Por medio de la presente Buffalo Technology Inc. declara que el AirStation WLI-U2-KG125S cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
[Greek]
Buffalo Technology Inc. AirStation WLI-U2-KG125S 1999/5/. Franais
[French]
Par la prsente Buffalo Technology Inc. dclare que lappareil AirStation WLI-U2-KG125S est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano
[Italian]
Con la presente Buffalo Technology Inc. dichiara che questo AirStation WLI-U2-KG125S conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. 42 Latviski
[Latvian]
Ar o Buffalo Technology Inc. deklar, ka AirStation WLI-U2-KG125S atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. Lietuvi
[Lithuanian]
iuo Buffalo Technology Inc. deklaruoja, kad is AirStation WLI-U2-KG125S atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlands
[Dutch]
Hierbij verklaart Buffalo Technology Inc. dat het toestel AirStation WLI-U2-KG125S in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti
[Maltese]
Hawnhekk, Buffalo Technology Inc. , jiddikjara li dan AirStation WLI-U2-KG125S jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm d-Dirrettiva 1999/5/EC. Magyar
[Hungarian]
Alulrott, Buffalo Technology Inc. nyilatkozom, hogy a AirStation WLI-U2-KG125S megfelel a vonatkoz 43 alapvet kvetelmnyeknek s az 1999/5/EC irnyelv egyb elrsainak. Polski
[Polish]
Niniejszym, Buffalo Technology Inc. , deklaruj, e AirStation WLI-U2-KG125S spenia wymagania zasadnicze oraz stosowne postanowienia zawarte Dyrektywie 1999/5/EC. Portugus
[Portuguese]
Buffalo Technology Inc. declara que este AirStation WLI-U2-KG125S est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE. Slovensko
[Slovenian]
Buffalo Technology Inc. izjavlja, da je ta AirStation WLI-U2-KG125S v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloili direktive 1999/5/ES. Slovensky
[Slovak]
Buffalo Technology Inc. tmto vyhlasuje, e AirStation WLI-U2-KG125S spa zkladn poiadavky a vetky prslun ustanovenia Smernice 1999/5/ES. Suomi
[Finnish]
Buffalo Technology Inc. vakuuttaa tten ett AirStation WLI-U2-KG125S tyyppinen laite on direktiivin 44 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Svenska
[Swedish]
Hrmed intygar Buffalo Technology Inc. att denna AirStation WLI-U2-KG125S str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG. 45 46 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that 47 to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modi cations not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. 48 To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. SAR compliance has been established in typical laptop computer(s) with USB slot, and product could be used in typical laptop computer with USB slot. Other application like handheld PC or similar device has not been verified and may not compliance with related RF exposure rule and such use shall be prohibited. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.
49 Contact Information (North America) ADDRESS Buffalo Technology (USA), Inc. 4030 West Braker Lane, Suite 120 Austin, TX 78759-5319 GENERAL INQUIRIES Email: sales@buffalotech.com TECHNICAL SUPPORT North American Technical Support by phone is available 24 hours a day, 7 days a week. (USA and Canada). Toll-free: (866) 752-6210 50 Contact Information (Europe) ADDRESS Buffalo Technology (Europe), Inc. 176 Buckingham Avenue, Slough, Berkshire, SL1 4RD United Kingdom GENERAL INQUIRIES Email: sales@buffalo-technology.com TECHNICAL SUPPORT Technical Support in Europe is available between the hours of 9am-6pm (GMT) Mon-
day to Thursday and 9am-4:30pm (GMT) Friday for this product. Customers in Europe can obtain Technical Support using the following information:
E-mail: helpdesk@buffalo-technology.ie | Web: www.buffalo-technology.com 51