XA-928WCP Car Multimedia Player XA- 928WCP USER MANUAL Tableofcontents Wiring Diagram General Operation AM/FM Tuner Operation Multimedia player AUX in/Rearview lens Phone Linq Software Setting Menu Troubleshooting Systematic Parameter 2 3 4 5 5 6 7 8 9 For your safety, the driver should not operate the controls while driving AIso , while driving , keep the volume to a level at which external sounds can be heard . precautions 1. when the interior of the car is extremely cold and the unit is used soon after switching on the heater and moisture may form on the unit and proper playback may not be possible. 2.This unit uses precision parts and components for its operation .In the event that trouble arises ,never open the case ,disassemble the unit ,or lubricate the rotating parts .Contact your service center. FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance between 20cm the radiator your body. MEDIA R.CAM V-IN B V-OUT1 C F.CAM L-IN F RL G A E SUB R-IN J RR K I R.CAM V-IN V-OUT1 V-OUT2 SUB R-IN RR FR F.CAM L-IN RL FL A. REAR CAM INPUT B. VIDEO INPUT C. VIDEO OUTPUT1 D. VIDEO OUTPUT2 E. FRONT CAM INPUT F. LEFT AUDIO INPUT G. REAR LEFT AUDIO OUTPUT H. FRONT LEFT AUDIO OUTPUT I. SUBWOOFER OUTPUT J. RIGHT AUDIO INPUT K. REAR RIGHT AUDIO OUTPUT L. FRONT RIGHT AUDIO OUTPUT V-OUT2 D FL H FR L Generaloperation Note: fthere isnoanydeviceconnection, some icons likecamera wil lbeshowednodevice.click is invalid inthiscase .Displaysetting is invalid ifthere isnoaudioorvideoplaying Radio Multimediaplayer EQ-setting :pop ,ROCK ,classic ,Jazzoroff Time slidethefigures inthe settime interface Language portuguese Frenchchines e,etc. camera inpu when reversing.(Note camera isnot included) 3 car logo steeringwheelcontro settin calibration calibrate the touchscreen powersavingmode AUX Input FMTUneroperat ion Radio interfaceRDsturnonfunction TouchRadio icon inmain interfaceorpressmodekey inpanel/SRckey in remotecontrollertoswitch to radiomode. 4 Multimedia player Support avarity of audio and video formats Music interface The system will automatically read certain devices inputted into the unit The user can directly click options in directory menu to perform play. Note: Sliding the controlling bar in the bottom to show the next page. AUX in(Auxiliary device input Click " AUX In " in from the main interface SRC key in remote control to switch to AUX in Mode. AUX in enables external media sources to connect to the system, like camera, video games, (controlled by remote control} etc. No auxiliary device input shows at the below picture. Connect external devices through the 3.5mm auxiliary audio/video input. It can display the corresponding picture as the output video. Rear view Camera Auto operation: After connect with reverse camera, it will auto-detected the reverse signal and show the reverse pictures. The system will swift to any mode to rear view lens mode automatically. When reverse is over, the system will come back to previous mode.
- - 5 - -
Connect to the unit via your mobile phone through the standard port and transfer the picture and audio from the phone to the device. You can control the phone through the device's screen , such as receiving calls, dialing calls, listening to music, watching movies or photos. Connect your device using the with original cable your phone came with, then touch the icon to open the menu, and follow the instructions.
- - 6 - -
setting Note:slidingthebaronthe leftsidetoseemore optionalsettings 7 Troubleshooting Phenomenon Normal Not operating Reasons Fuse of machine power supply and auto vehicle battery is burnt, Volatge of power supply is overloaded Automatic protection system avoids fault due to illegal operation Wrong pin assignment ISO connector Battery is not placed correctly Remote comtrol Battery is out of power;
doesn't work Noor low sound connection of Silence; Loudspeaker fault;
Volume balance setting bias Earthing in loudspeaker connection Disconnection;
Volume setting is low volume; wrong Solutions Change for fuse of the collect types;
Adjust voltage;
Reset the system by pressing the Resetkey Check the wiring diagram Change new battery;
Reinstall battery Check the connecion; Increase the volume; Reconnection the silence wire complied with the installation instruction; Change for a new loudspeaker; Adjust the volume balance setting to middle place;
Machine reset b}
itself when it is Connection of ACC and B+ is not correct. Check and reconnect ACC and B+
shutdown Turnover screen Turnover screen does not open Auto Open of turnover screen setting Auto OpenON automatically. is OFF. No image Connection of brake wire is not correct; Connect brake wire with cathode of Not brake state power supply correctly; Keep brake state after car is placed safe. Unstable output does not correspond with the present Adjust system video setting;
of images system video setting; Check and make sure of the Video signal line is not connected correctly. connectivity. Unsupported code Images being stretched or Inappropriate image proportion setting Adjust image setting compression Trouble Cause(sl Solution Cs) Radio Weak signal Auto antenna does not reach out completely Connect auto antenna line correctly;
LOG function is under workina state Close LOG function. Note: This device is a Mechless unit.
- - 8 - -
Systematic Parameter Specifications FM Radio Working voltage: direct current 12V Working voltage range: 10.8V-16V Maximum working electronic current: 10A Installation angle: less than 30 degree tilted the front side and backside Power output: 4X80 W impedance 4ohm SNR: 70dBA Frequency Response: 20Hz-20kHz Video Standards: NTSC. PAL (Auto recognition) Output: 2 Vp-p(75ohm) Input: 1Vp-p(75ohm) Frequency modulation:
87.5 MHz ~108.0MHz (Europe) Flexibility (-30dB):10dBu SNR(- 50dB):15dBu Frequent sound range:
30H2-15kHz (+3dB) AM Radio Frequency range:
522KHZ-1620KHZ (Europe) Sensitivity (SN=20dB):20dBu Image rejection: 60dB Frequency response:
50HZ-2KHZ(+-3dB) Display Response time: up=30 millisecond. Down=50 millisecond Angle range: depression angle=65o elevation angle=40<>
Left vision=65 right vision=65 Environment temperature Operation temperature:-20-+70oC Maintenance temperature: -30oC-80oC Operating humidity:45%-+80%oC
(relative humidity) Maintenance humidity:30%-90%
(relative humidity)
- - 9 - -