all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
User Manual | Users Manual | 1.22 MiB | January 08 2013 | |||
1 2 | Cover Letter(s) | January 08 2013 | ||||||
1 2 | Operational Description | January 08 2013 | ||||||
1 2 | Test Report | January 08 2013 | ||||||
1 2 | Cover Letter(s) | |||||||
1 2 | External Photos | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | Internal Photos | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | RF Exposure Info | |||||||
1 2 | Test Setup Photos |
1 2 | User Manual | Users Manual | 1.22 MiB | January 08 2013 |
A528B A528ADAT USB RS232 Adapter Board Compact Embedded UHF RFID Reader Technical Information Manual Revision n. 05 16/07/2013 Scope of Manual The goal of this manual is to provide the basic information to work with the A528B Muon Compact Embedded UHF RFID Reader. Change Document Record Date Revision Changes 20 Feb 2013 19 Mar 2013 21 Mar 2013 30 Apr 2013 27 May 2013 16 Jul 2013 00 01 02 03 04 05 Preliminary release Added EC Declaration of Conformity Modified Return link characteristics in the Tab. 2.1: Muon A528B Technical Specifications Added Federal Communications Commission (FCC) Notice
(Preliminary) Added FCC Compliance paragraph Changed Tab. 2.1: Muon A528B Technical Specifications Table Modified FCC Compliance paragraph Modified FCC Compliance paragraph Pages
27, 29 10 3 27 10 27 27 Reference Document
[RD1]
[RD2]
EPCglobal: EPC Radio-Frequency Identity Protocols Class-1 Generation-2 UHF RFID Protocol for Communications at 860 MHz 960 MHz, Version 1.1.0 (December 17, 2005). G.S.D. s.r.l. - Report CE mark A528B Muon Compact Embedded UHF RFID Reader. Test report n. 13122 Rev.00 - 12 March 2013. CAEN RFID srl Via Vetraia, 11 55049 Viareggio (LU) - ITALY Tel. +39.0584.388.398 Fax +39.0584.388.959 info@caenrfid.com www.caenrfid.com CAEN RFID srl 2010 Disclaimer No part of this manual may be reproduced in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of CAEN RFID. The information contained herein has been carefully checked and is believed to be accurate; however, no responsibility is assumed for inaccuracies. CAEN RFID reserves the right to modify its products specifications without giving any notice; for up to date information please visit www.caenrfid.com. Federal Communications Commission (FCC) Notice (Preliminary) This device was tested and found to comply with the limits set forth in Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This device generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instruction manual, the product may cause harmful interference to radio communications. Operation of this product in a residential area is likely to cause harmful interference, in which case, the user is required to correct the interference at their own expense. The authority to operate this product is conditioned by the requirements that no modifications be made to the equipment unless the changes or modifications are expressly approved by CAEN RFID. Disposal of the product Do not dispose the product in municipal or household waste. Please check your local regulations for disposal/recycle of electronic products. Index 2 Scope of Manual .................................................................................................................................................................. 2 Change Document Record .................................................................................................................................................... 2 Reference Document ........................................................................................................................................................... 2 Index .......................................................................................................................................................................................... 4 List of Figures ................................................................................................................................................................................. 5 List of Tables .................................................................................................................................................................................. 5 1 Introduction ........................................................................................................................................................................ 6 General Information ............................................................................................................................................................ 7 Ordering Options ................................................................................................................................................................. 8 Muon A528B ....................................................................................................................................................................... 9 Technical Specifications Table ............................................................................................................................................ 10 External Connections ......................................................................................................................................................... 11 A528B Main connector pinout ................................................................................................................................ 11 A528B Main connector electrical characteristics ..................................................................................................... 12 Power supply connection ....................................................................................................................................... 13 General purpose I/O connections ........................................................................................................................... 13 External reset ........................................................................................................................................................ 14 UART connection ................................................................................................................................................... 14 A528B recovery ..................................................................................................................................................... 15 A528B USB connector pinout ................................................................................................................................. 15 A528B USB connector electrical characteristics ....................................................................................................... 16 Antenna port specifications.................................................................................................................................... 16 Reader - Tag Link Profiles ................................................................................................................................................... 17 Host communication interfaces .......................................................................................................................................... 17 Firmware Upgrade ............................................................................................................................................................. 18 A528B USB Recovery/FW upgrade .......................................................................................................................... 18 A528B RS232 Firmware upgrade ............................................................................................................................ 19 Muon A528ADAT............................................................................................................................................................... 20 Technical Specifications Table ............................................................................................................................................ 21 Connection Diagram .......................................................................................................................................................... 21 Installation Notice .................................................................................................................................................. 22 Technical drawings ............................................................................................................................................................ 23 Electrical scheme ............................................................................................................................................................... 24 External Connections ......................................................................................................................................................... 25 LEDs .................................................................................................................................................................................. 25 Switches ............................................................................................................................................................................ 25 Firmware Upgrade ............................................................................................................................................................. 25 Muon Regulatory Compliance ........................................................................................................................................... 26 FCC Compliance ................................................................................................................................................................. 27 CE Compliance ................................................................................................................................................................... 27 RoHS EU Directive .............................................................................................................................................................. 28 EC Declaration of Conformity ............................................................................................................................................. 29 3 4 4 Muon A528B - A528ADAT - Technical Information Manual List of Figures Fig. 1.1: Muon A528B OEM UHF Compact Reader............................................................................................................................ 7 Fig. 1.2: Muon A528ADAT USB RS232 Adapter ................................................................................................................................ 7 Fig. 2.1: Muon A528B Technical Drawings ..................................................................................................................................... 11 Fig. 2.2: Muon A528B Power Supply Connection ........................................................................................................................... 13 Fig. 2.3: Muon A528B GPIO Connection Example ........................................................................................................................... 13 Fig. 2.4: Muon A528B External Reset ............................................................................................................................................. 14 Fig. 2.5: Muon A528B RS232 Connection ....................................................................................................................................... 14 Fig. 2.6: Muon A528B TST-Recovery Connection ............................................................................................................................ 15 Fig. 2.7: Muon A528B USB Interface Connection ........................................................................................................................... 15 Fig. 3.1: Muon A528ADAT Connection Diagram ............................................................................................................................. 21 Fig. 3.2: Connection of the Muon A528B module to the A528ADAT adapter board ......................................................................... 22 Fig. 3.3: Muon A528ADAT Technical Drawing ................................................................................................................................ 23 Fig. 3.4: Muon A528ADAT Electrical Scheme ................................................................................................................................. 24 List of Tables Tab. 2.1: Muon A528B Technical Specifications ............................................................................................................................. 10 Tab. 2.2: Muon A528B Main Connector Pinout .............................................................................................................................. 11 Tab. 2.3: Muon A528B Main Connector electrical characteristics ................................................................................................... 12 Tab. 2.4: Muon A528B USB Connector Electrical Specifications ...................................................................................................... 15 Tab. 2.5: Muon A528B USB Connector Electrical Characteristics .................................................................................................... 16 Tab. 2.6: RF Port Pinout ................................................................................................................................................................ 16 Tab. 2.7: RF Port Electrical Characteristics ..................................................................................................................................... 16 Tab. 2.8: Muon A528B Reader to Tag Link Profiles ......................................................................................................................... 17 Tab. 3.1: Muon A528ADAT Technical Specifications ....................................................................................................................... 21 Muon A528B - A528ADAT - Technical Information Manual 5 1 Introduction This Chapter gives general information about the A528B Muon Compact Embedded UHF RFID Reader. It contains these topics:
General Information Ordering Options 6 Muon A528B - A528ADAT - Technical Information Manual General Information The Muon (Model A528B) is an OEM UHF multiregional compact reader of the easy2read Family for high performances UHF RFID applications. With programmable output power in 8 steps from 10dBm to 27dBm, the reader can detect tags up to 3m of distance1. Due to its form factor, the module is specifically designed to be easily embedded either in battery powered devices, such as industrial handhelds, or fixed reading point devices, such as printers, point of sales, self-service kiosks or industrial automation readers. The radio frequency core of the module allows achieving fast reading/writing and operation in dense reader and dense tag environments for top-class rated performances. The A528B complies with and can operate in both European and US regulatory environments and, due to its multiregional capabilities, it's ideal for integration in devices requiring compliance to different geographical regions. Fig. 1.1: Muon A528B OEM UHF Compact Reader The Mod. A528ADAT USB / RS232 service board allows managing the Mod. A528B OEM UHF multiregional Compact Reader directly via USB and RS232 interfaces. This board is particularly suited for A528B reader evaluation and SW development purpose. Fig. 1.2: Muon A528ADAT USB RS232 Adapter 1 depending on antenna and tag dimensions. Muon A528B - A528ADAT - Technical Information Manual 7 Ordering Options Reader Accessories Code WA528BXAAAAA WANTENNAX004 WANTENNAX008 WANTENNAX009 WANTENNAX010 WANTENNAX011 WANTENNAX012 A528ADAT WALIM0000002 Description A528B Muon Compact Embedded UHF RFID Reader. Linear polarized 3db gain 870 MHz PIFA antenna Linear polarized antenna for handheld units 865 - 870 MHz Linear polarized antenna for printers 865 - 870 MHz Linear polarized 3db gain 915 MHz PIFA antenna Linear polarized antenna for handheld units 915 MHz Linear polarized antenna for printers 902 - 928 MHz A528 (MUON) USB/RS232 Adapter Board Power Supply for A528 Adapter Board 8 Muon A528B - A528ADAT - Technical Information Manual 2 Muon A528B This Chapter provides the basic information to work with the A528B Muon Compact Embedded UHF RFID Reader. It contains these topics:
Technical Specifications Table External Connections Reader - Tag Link Profiles Host communication interfaces Firmware Upgrade Muon A528B - A528ADAT - Technical Information Manual 9 Technical Specifications Table Frequency Range RF Power Output Power Accuracy Antenna VSWR Requirement Antenna Connector Frequency Tolerance Number of Channels Standard Compliance Forward link characteristics Return link characteristics Digital I/O Connectivity Dimensions DC Power Power Consumption Operating Temperature Weight 902928 MHz (FCC part 15.247) 865.600867.600 MHz (ETSI EN 302 208 v1.4.1) Programmable in 8 levels from 10dBm to 27dBm
+/- 1dB
<2:1 or better for optimum performances Nr. 1 MMCX jack 10 ppm over the entire temperature range 4 channels (compliant to ETSI EN 302 208 v1.4.1) 50 hopping channels (compliant to FCC part 15.247) EPC C1G2 [RD1]
DSB-ASK 40kBit/s; PR-ASK 40kBit/s; DSB-ASK 160kBit/s (FCC only) FM0 40kbit/s Miller encoding (M=4;LF=250kHz) Miller encoding (M=4;LF=300kHz) FM0 400kbit/s (FCC only) Four I/O lines 3.3V out @ 3mA; 5V tolerant UART Serial Port:
Baudrate: up to 115200 Databits: 8 Stopbits: 1 Parity: none Flow control: none 3.3V level USB Device Port:
One USB 2.0 Full Speed (12 Mbits per second) device port.
(W)42 x (L)60 x (H)6.3 mm3
(1.65 x 2.36 x 0.25 inch3) 4.75V 5.25V ripple and noise < 100mVpp ripple frequency > 100kHz 1A peak @ 5 V (TX/RX mode) 230 mA @ 5 V (idle mode)
-20 C to 60 C 18 g Tab. 2.1: Muon A528B Technical Specifications Warning: please set up the correct RF regulation of your country following the CAEN RFID instructions. 10 Muon A528B - A528ADAT - Technical Information Manual External Connections The location of the connectors is shown in Fig. 2.1: Muon A528B Technical Drawings pag. 11. Their mechanical specifications are listed here below:
Antenna Port: RF Coax Connector Huber+Suhner type 82MMCX-S50-0-2/111_K (to be used with Huber+Suhner type 11MMCX-50-1-1/111_O) MOLEX Connector: PCB Headers Molex type 53261-1271
(to be used with Molex Type 51021-1200 + 12pcs crimp terminal type 50058-8100) MOLEX Connector: PCB Headers Molex type 53261-0271
(to be used with Molex Type 51021-0200 + 2pcs crimp terminal type 50058-8100) Fig. 2.1: Muon A528B Technical Drawings A528B Main connector pinout Compact reader A528B MAIN external connector is a Molex SMD, 12 poles, 1.27 pitch connector whose pinout is shown in table below. Pin #
Function Direction 1 2 3 4 5 6 7 8 9 10 11 12 Power Line (+5V)
/RESET GPIO0 GPIO1 GPIO2 GPIO3 TST_RECOVERY USB PUP RXD TXD GND GND
IN IN/OUT IN/OUT IN/OUT IN/OUT IN IN IN OUT
Tab. 2.2: Muon A528B Main Connector Pinout The GPIO0-GPIO3 pin are 4 general purpose bidirectional pins, their default direction (or after a Reset) is OUT. Muon A528B - A528ADAT - Technical Information Manual 11 TST_RECOVERY pin is reserved and shall be used only to perform the microcontroller recovery procedure during which it must be forced at high level (3.3V or 5V). The RXD/TXD pins are used to communicate with the A528 board via UART port; to establish a link with the device you must configure your COM port as follows2:
Baud rate:
115200 Parity:
None Data bits:
Stop bits:
8 1 Flow Control: none A528B Main connector electrical characteristics3 Pin name Pin No.
+5V
/RESET 1 2 Parameter Supply DC voltage Power supply requirements Ripple Voltage Power supply requirements -
Ripple Frequency Supply DC current VIL VIH Internal pull-up resistance GPIO[0:3]
3, 4, 5, 6 TST-Recovery USB PUP RXD TXD GND 7 8 9 10 11,12 Pulse width VOL VOH Output current VIL VIH Input current VIH VIH VIL VIH Input current VOL VOH Output current Tab. 2.3: Muon A528B Main Connector electrical characteristics Min 4.75 100 0.23
-0.3 2.4 10 1 0 2.0
-0.3 2.0 2.0 2.0
-0.3 2.0 0 2.4 Typ 5.00 20 Max 5.25 100 Unit V mVpp 1.0 1.0 3.6 0.4 3.3 3.0 0.8 5.5 1 5.5 5.5 0.8 5.5 1 0.4 3.3 1.5 kHz A V V k s V V mA V V A V V V V A V V mA 2 Since A528B RX/TX are TTL level signals, in order to connect it with a PC, a TTL/RS232 translator shall be used. 3 Exceeding maximum values reported in the table may cause permanent damage to the model. 12 Muon A528B - A528ADAT - Technical Information Manual Power supply connection In the following schematic suggested A528B power supply connection is shown. The use of fuse F1 is recommended since A528B does not provide internal current limitation protection. Diode D1 avoid damage to the reader in case of reverse polarity connection. The use of optional LC filter improves reader immunity in presence of noisy power supply. In order to ensure the correct operation of the reader the power supply shall not enter in burst mode (switching frequency less than 100 kHz) when A528B reader is in idle mode (supply current less than 0.2A). As a rule of thumb the power adapter shall have a maximum current rating from 1A to 1.5A. Fig. 2.2: Muon A528B Power Supply Connection General purpose I/O connections The GPIO0-GPIO3 pins are 4 general-purpose bidirectional pins. Their default direction after a power on reset or a general reset is set to Output. GPIO, when configured as Outputs, can be used to drive indicators as leds or buzzers or to send trigger signal to others equipments. GPIO, when configured as Inputs, can accept control signals from other equipments or trigger signals from sensors (i.e. photocells). In the following schematic an example of application of GPIO is shown. Fig. 2.3: Muon A528B GPIO Connection Example Muon A528B - A528ADAT - Technical Information Manual 13 External reset A528B manual reset can be performed by forcing at low level /RESET pin for 1S at least. /RESET pin is pulled-up by an internal resistor. Fig. 2.4: Muon A528B External Reset UART connection The RXD/TXD pins are used to communicate with the A528 board via UART port. Since A528B RX/TX are TTL level signals, in order to connect it with a PC, a TTL/RS232 translator shall be used (please refer to the diagram below)4. To establish a link with the device host COM port shall be configured as follows:
Baud rate:
115200 Parity:
None Data bits:
Stop bits:
8 1 Flow Control: none Fig. 2.5: Muon A528B RS232 Connection 4 A528 service board (A528ADAT) hosts both RS232 and USB full interfaces. 14 Muon A528B - A528ADAT - Technical Information Manual A528B recovery TST_RECOVERY pin is reserved and shall be used only to perform the microcontroller recovery procedure during which it must be forced at high level (3.3V or 5V). In the following diagram a manual recovery mechanism is shown: in order to perform the A528B boot recovery the jumper JP1 shall be inserted, than A528B shall be switched on by applying 5V supply voltage for 5s at least. After that the reader shall be switched off and the jumper removed: at the next switch on the reader will execute the boot recovery program. For further details please see Firmware Upgrade pag.18. Fig. 2.6: Muon A528B TST-Recovery Connection A528B USB connector pinout A528B USB interface connector is a Molex SMD, 2 poles, 1.27 pitch connector whose pinout is shown in table below. Pin #
Function 1 2 DDM DDP Direction IN/OUT IN/OUT Description USB data -
USB data +
Tab. 2.4: Muon A528B USB Connector Electrical Specifications A528 board provides only the USB data signals; in order to implement a full USB interface some external components shall be used. The external circuit necessary for A528B USB operation is shown in the schematic below. Fig. 2.7: Muon A528B USB Interface Connection Muon A528B - A528ADAT - Technical Information Manual 15 Unit V V V V V V V V Max 0.8 0.3 3.3 0.8 0.3 3.3 A528B USB connector electrical characteristics5 Pin name Pin No. Parameter Min Type DDM 1 DDP 2 VIL VIH VOL VOH Recommended external series resistor VIL VIH VOL VOH Tab. 2.5: Muon A528B USB Connector Electrical Characteristics Recommended external series resistor Antenna port specifications In the following table the pinout of A528B antenna is shown. 2 0 2.8 2 0 2.8 27 27 Pin #
INNER OUTER Function RF OUT GND Tab. 2.6: RF Port Pinout Parameter RF output power (nominal) Output power vs. power setting accuracy RF port impedance Recommended antenna VSWR Tab. 2.7: RF Port Electrical Characteristics Direction OUT
Description RF output Ground Min 10 10 Typ. 50 Max 500 27 1 2:1 Unit mW dBm dB
5 Exceeding maximum values reported in the table may cause permanent damage to the model. 16 Muon A528B - A528ADAT - Technical Information Manual Reader - Tag Link Profiles A528B reader supports different modulation and return link profiles according to EPC Class1 Gen2 protocol [RD1]. In the following table are reported all profiles that have been tested for the compliance with ETSI and FCC regulations. Link profile #
0 1 2 3 4 Regulation ETSI - FCC ETSI - FCC ETSI FCC FCC Modulation DSBASK; f=40kHz PR-ASK; f=40kHz PR-ASK; f=40kHz DSB-ASK; f=160kHz PR-ASK; f=40kHz Return Link FM0; f = 40kHz Miller (M=4); f = 250kHz Miller (M=4); f = 300kHz FM0; f = 400kHz Miller (M=2); f = 250kHz Tab. 2.8: Muon A528B Reader to Tag Link Profiles Host communication interfaces A528B reader allows the user to manage host communication through the CAEN communication protocol6: the host-
reader interface is serial and A528B is fully compatible with all the CAEN Demos and libraries included in the Easy2Read SDK. Only if the use of USB interface is necessary, it is available the Intel communication protocol: the host-reader interface is USB. Using the Intel protocol, serial interface has debug purpose only. Intel communication protocol is not supported by CAEN RFID. The default setting of the A528B reader is the Serial/CAEN choice, in order to switch to the INTEL protocol on USB interface you shall follow the steps described below:
1. Connect to the reader, using a RS232 cable7, with the Hyperterminal (or with any other terminal emulation application) with the following settings:
baud rate:
data bits:
parity:
stop bits:
Flow control:
115200 8 none 1 None 2. Type quickly the word CAEN (in capital letters) in the hyperterminal window. 3. Type chgprot in the hyperterminal window. 4. Select the USB interface and INTEL protocol options when prompted. After a reset the reader will reply to the INTEL commands. In order to switch from the INTEL protocol on USB interface to the Serial/CAEN protocol you shall follow the steps described below:
1. 2. 3. 4. Connect to the reader, using a RS232 cable8, with the hyperterminal (or with any other terminal emulation application) with the following settings:
baud rate:
data bits:
parity:
stop bits:
Flow control:
115200 8 none 1 None Stop the boot process pressing the spacebar within 6 seconds from the power on. Type chgprot in the hyperterminal window. Select the Serial interface and CAEN protocol options when prompted. After a reset the reader will reply to the CAEN commands. 6 Serial / CAEN procotol is implemented starting from FW release 1.1.5. 7 Assuming to use A528 adapter board and a PC as host. 8 Assuming to use A528 adapter board and a PC as host. Muon A528B - A528ADAT - Technical Information Manual 17 Firmware Upgrade The A528B reader firmware upgrade can be performed via USB or RS232 interface. In the use of RS232 interface, it is assumed to use the A528 adapter board and a PC as host. A528B USB Recovery/FW upgrade USB upgrade is based on Atmel Smart Arm Microcontroller Boot Assistant (hence forth referred to as SAM-BA). The SAM-BA tool is distributed by Atmel and it is available for free at Muon A528B web page or in the Software and Firmware Area of the CAEN RFID Web Site (download the SAM-BA tool and install the AT91-ISP.exe file). USB upgrade requires the following steps:
With power supply disconnected, connect with a jumper J5 pin 1 and pin 2. With short circuit inserted connect the power supply to the board and wait for 5 seconds at least. Disconnect the power supply. At this point, Windows XP will detect the platform (in SAM-BA mode) and display the Found New Hardware Remove the jumper. Connect the power supply and the USB cable to A528ADAT. Wizard. The first screen asks if Windows can connect to Windows Update to search for the software, select: No, not this time and then click the NEXT button. On the next wizard screen, select: Install the software automatically then click the NEXT button. A dialog will popup indicating that the driver has not passed Windows Logo Testing, click the CONTINUE ANYWAY button. Reboot PC when prompted. Run the SAM-BA v2.6 application on the WinXP host machine. When the last screen appears, click the Finish button to dismiss the New Hardware Wizard. When a dialog box appears, ensure AT91SAM7S256-EK is selected in the drop down list then click on the USB connection button. Note that a number of the names in the dropdown list are similar so ensure you select the correct one. Ensure the FLASH tab is selected. Enter the path in the Send File Name or use the corresponding Browse button to find and select the file containing the new firmware. Latest release can be downloaded from CAEN RFID website. Click the Send File button. Click Yes in response to Do you want to unlock involved lock region(s). Click No in response to Do you want to lock involved lock region(s). Finally - confirm the programming by clicking the Compare sent file with memory button. When SAM-BA reports that the files are identical click the OK button. Exit the SAM-BA application via the File -> Quit option. To ensure correct behaviour of Windows XP, click the Safely Remove Hardware icon in the Windows system tray, and Stop the Atmel Test Board entry and power DOWN your A528ADAT (disconnect power supply). 18 Muon A528B - A528ADAT - Technical Information Manual A528B RS232 Firmware upgrade The Muon A528B Upgrade Tool is available for free at Muon A528B web page or in the Software and Firmware Area of the CAEN RFID Web Site. To perform the FW upgrade via RS232 interface these steps shall be followed:
Turn off the reader. Connect the reader with the RS232 serial cable to your PC using the adapter board A528ADAT. Setup a serial terminal (such hyperterminal available on all windows OS) with the following settings:
baud rate:
data bits:
parity:
stop bits:
Flow control:
115200 8 none 1 None Turn on the reader. Type quickly and in capital letters the word CAEN. In case the A528B is configured to use INTEL protocol a boot message will appear, press the space bar within 8 seconds from boot. After that in both cases a prompt ">" should be displayed. The reader is waiting for commands to be sent over the serial port. Type upgrade, press return and disconnect the serial port. Launch the downloaded upgrade tool (AT91SAM7SERIALBOOT.exe). Select the COM port you are using (typically is COM1) with the radio button on the left of the main window and press the connect button. Click the Open button and Browse until you find the .bin firmware upgrade image. Press the Download button. If, for any reason, the upgrade procedure fails, do not power off the reader but press the download button again. At the end power off the reader and power it on again. Firmware upgrade has been completed. If some problems occur in this procedure, the recovery of module operation can be obtained by performing the procedure described in A528B USB Recovery/FW upgrade pag. 18. Muon A528B - A528ADAT - Technical Information Manual 19 3 Muon A528ADAT This Chapter provides the basic information to work with the Muon A528ADAT USB RS232 Adapter Board. It contains these topics:
Technical Specifications Table Connection Diagram Technical drawings Electrical scheme External Connections LEDs Switches 20 Muon A528B - A528ADAT - Technical Information Manual Technical Specifications Table USB Port Digital I/O RS232 Port Four I/O lines 3.3 V out @ 3mA, 5 V tolerant USB B female connector USB 2.0 device It appears as USB A528B device; drivers for Windows XP, Windows CE 5.0, Linux 4 and greater Baudrate: 115200 Databits: 8 Stopbits: 1 Parity: none Flow control: none 9.6115 kbit/s data rate (settable) RED: Power GREEN: GPIO[0..3], USB connection YELLOW: RECOVERY procedure
(W)81 x (L)76 x (H)28 mm3
(3.2 x 3.0 x 1.1 inch3) DC Voltage 5V +/-5%
Current consumption: 1A max.
-20 C to +60 C Tab. 3.1: Muon A528ADAT Technical Specifications Operating Temperature Electrical Power Dimensions LED display Connection Diagram The following block diagram shows how to connect the Muon A528B with the PC host via the Muon A528ADAT service board. The board equipped with A528B reader shall be powered by external 5V 1A DC adapter. In order to ensure the correct operation of the reader the power supply shall not enter in burst mode (switching frequency less then 100kHz) when A528B reader is in idle mode (supply current about 0.2A). As a rule of thumb the power adapter shall have a maximum current rating from 1A to 1.5A. Fig. 3.1: Muon A528ADAT Connection Diagram Muon A528B - A528ADAT - Technical Information Manual 21 Installation Notice Fix the Muon A528B reader to the A528ADAT using 3 screws M2,5x12 and 3 screws nuts M2,5 and connect the respective connectors. The correct way to connect the Muon A528B module to the A528ADAT adapter board is shown in the following picture:
Fig. 3.2: Connection of the Muon A528B module to the A528ADAT adapter board 22 Muon A528B - A528ADAT - Technical Information Manual Technical drawings The following drawing shows the Muon A528ADAT components position. Connectors to A528B reader Muon A528B reader mounting location Fig. 3.3: Muon A528ADAT Technical Drawing Muon A528B - A528ADAT - Technical Information Manual 23 Electrical scheme The electrical scheme of the Muon A528ADAT is shown in Fig. 3.4: Muon A528ADAT Electrical Scheme. Fig. 3.4: Muon A528ADAT Electrical Scheme 24 Muon A528B - A528ADAT - Technical Information Manual External Connections Please refer to Fig. 3.3: Muon A528ADAT Technical Drawing pag.23. J1: free PTH pads for GPIO external connection J1-1 = GPIO0 (in/out) J1-2 = GPIO3 (in/out) J1-3 = GPIO1 (in/out) J1-4 = TST_RECOVERY J1-5 = GPIO2 (in/out) J1-6 = Not Connected J2: Power Supply connector: central pin (2.54mm diam.) is the positive terminal. J3: RS232 DB9 female connector J4: USB Type B port J5: Connector for Boot Recovery Procedure LEDs Please refer to Fig. 3.3: Muon A528ADAT Technical Drawing pag.23. DL1 (red) = Power Supply DL2 (green) = GPIO0 DL3 (green) = GPIO1 DL4 (green) = GPIO2 DL5 (green) = GPIO3 DL6 (yellow) = TST_RECOVERY DL7 (green) = USB connection Switches Please refer to Fig. 3.3: Muon A528ADAT Technical Drawing pag.23. SW1 = RESET Firmware Upgrade Please refer to Firmware Upgrade pag. 18. Muon A528B - A528ADAT - Technical Information Manual 25 4 Muon Regulatory Compliance This Chapter gives information on the Muon A528B Reader Regulatory Compliance. It contains these topics:
FCC Compliance CE Compliance RoHS EU Directive EC Declaration of Conformity 26 Muon A528B - A528ADAT - Technical Information Manual FCC Compliance This equipment has been tested and found to comply with Part 15 of the FCC Rules. NOTE:
a. b. Any changes or modification not approved by CAEN RFID could void the users authority to operate the equipment. The Muon A528B Module, which is rated at 500 mW output, is approved for operation with the following antennas:
1. CAENRFID antenna Mod. WANTENNAX010 (Linear polarized 3dbi gain PIFA antenna for portable and desktop systems - 915 MHz). 2. Antenova mod. A10315 (Reflexus Penta-band SMD Antenna; 2dBi gain). Use of other than the approved antennas with this unit may result in harmful interference with other users, and cause the unit to fail to meet regulatory requirements. The maximum allowed antenna gain to be used with A528B module is 3dBi. c. This transmitter module is authorized to be used in other devices only by OEM integrators under the following conditions:
1. The RFID Module antenna shall have a separation distance of at least 20 cm from all persons 2. The transmitter module must not be co-located with any other antenna or transmitter d. In case that the two conditions above are met, further transmitter testing will not be necessary. However, the OEM integrator is still responsible for testing the end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). In the event that these conditions can not be met (for certain configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In such case the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. e. If the FCC ID is not visible when the module is installed inside another device, the OEM integrator shall apply a label in a visible area on his product with the following statement:
Contains Transmitter Module FCC ID: UVECAENRFID016 or Contains FCC ID: UVECAENRFID016 f. The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. CE Compliance Reference standard:
CEI EN 60950-1:2007 ETSI EN 301 489-1 V. 1.9.2:2011 ETSI EN 301 489-3 V. 1.4.1:2002 ETSI EN 302 208-2 V. 1.4.1:2011 CEI EN 50364:2011 Reference document: Test report n. 13122 [RD2]. See EC Declaration of Conformity pag. 29 for the Muon A528B CE Compliance Certificate. Muon A528B - A528ADAT - Technical Information Manual 27 RoHS EU Directive Muon A528B OEM UHF multiregional Compact Reader is compliant with the EU Directive 2002/95/EC on the Restriction of the Use of certain Hazardous Substances in Electrical and Electronic Equipment (RoHS). Warning: please set up the correct RF regulation of your country following the CAEN RFID instructions. 28 Muon A528B - A528ADAT - Technical Information Manual EC Declaration of Conformity We CAEN RFID Srl Via Vetraia, 11 55049 Viareggio (LU) Italy Tel.: +39.0584.388.398 Fax: +39.0584.388.959 Mail: info@caenrfid.com Web site: www.caenrfid.com herewith declare under our own responsibility that the product:
Code:
WA528BXAAAAA Description:
A528B Muon Compact Embedded UHF RFID Reader corresponds in the submitted version to the following standards:
CEI EN 60950-1:2007 ETSI EN 301 489-1 V. 1.9.2:2011 ETSI EN 301 489-3 V. 1.4.1:2002 ETSI EN 302 208-2 V. 1.4.1:2011 CEI EN 50364:2011 The present document declares that the specified product complies with the reported standards and satisfies the essential requirements of the European regulation R&TTE Directive 99/5/EC. Date: 19/03/2013 Adriano Bigongiari (Chief Executive Officer) On the basis of this declaration, this product will bear the following mark:
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2013-08-01 | 902.75 ~ 927.25 | DSS - Part 15 Spread Spectrum Transmitter | Class II permissive change or modification of presently authorized equipment |
2 | 2013-06-20 | 902.75 ~ 927.25 | DSS - Part 15 Spread Spectrum Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2013-08-01
|
||||
1 2 |
2013-06-20
|
|||||
1 2 | Applicant's complete, legal business name |
CAEN RFID srl
|
||||
1 2 | FCC Registration Number (FRN) |
0015858780
|
||||
1 2 | Physical Address |
via Vetraia, 11 - 55049 Viareggio (LU) - ITALY
|
||||
1 2 |
Viareggio, N/A 55049
|
|||||
1 2 |
Italy
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
k******@emcc.de
|
||||
1 2 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 2 | Grantee Code |
UVE
|
||||
1 2 | Equipment Product Code |
CAENRFID016
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
A****** B******
|
||||
1 2 | Title |
CEO
|
||||
1 2 | Telephone Number |
+3905********
|
||||
1 2 | Fax Number |
+3905********
|
||||
1 2 |
a******@caen.it
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
1 2 | Yes | |||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | DSS - Part 15 Spread Spectrum Transmitter | ||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | A528B - Muon - Compact Embedded UHF RFID Reader | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Single Modular Approval | |||||
1 2 | Purpose / Application is for | Class II permissive change or modification of presently authorized equipment | ||||
1 2 | Original Equipment | |||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | Power output listed is peak conducted. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
G.S.D. S.r.l. Testing Laboratory
|
||||
1 2 | Name |
D**** G******
|
||||
1 2 | Telephone Number |
39050********
|
||||
1 2 | Fax Number |
39050********
|
||||
1 2 |
j******@gsd.it
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 902.75000000 | 927.25000000 | 0.5000000 | ||||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15C | 902.75000000 | 927.25000000 | 0.5000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC