FCC ID: APV-3240LA HotSpot OBD Dongle

LMU-3240 CalAmp LMU-3240 Hardware and Installation Guide Rev. 1.0 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 CalAmp reserves the rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Table of Contents 1 Introduction ............................................................................................................................................. 4 1.1 1.2 1.3 1.4 2.1 2.2 About This Manual ........................................................................................................................... 4 About The Reader ............................................................................................................................ 4 About CalAmp .................................................................................................................................. 4 About the CalAmp Location Messaging Unit-LMU-3240 ............................................................. 5 2 System Overview ..................................................................................................................................... 6 Overview .......................................................................................................................................... 6 Component Descriptions ................................................................................................................. 7 2.2.1 Wireless Data Network ............................................................................................................ 7 LMU-3240 ............................................................................................................................. 7 LM Direct Server ................................................................................................................... 7 Backend Software .................................................................................................................... 7 PULS ...................................................................................................................................... 8 LMU Manager ....................................................................................................................... 8 2.2.7 Wireless Data Network ............................................................................................................ 8 2.2.8 LMU-3240 ............................................................................................................................. 8 3 Hardware Overview ................................................................................................................................. 9 3.1 Location Messaging Unit-LMU-3240 .......................................................................................... 10 3.1.1 LMU-3240 Handling Precautions ........................................................................................ 10 Battery Back-up devices ........................................................................................................ 11 Environmental Specifications ................................................................................................ 12 3.2 LMU-3240 Connectors ................................................................................................................ 14 Primary Connector ................................................................................................................. 14 Serial Adapter ........................................................................................................................ 16 Accessories ............................................................................................................................ 16 3.3 I/O Descriptions ............................................................................................................................. 16 3-Axis Accelerometer + 3-Axis Gyroscope ............................................................................ 17 Status LEDs ............................................................................................................................. 17 2.2.2 2.2.3 2.2.4 2.2.5 2.2.6 3.1.2 3.1.3 3.2.1 3.2.2 3.2.3 3.3.1 3.3.2 COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 2 of 37 Revision &

Date 1.0 07/22/2019 LMU-3040 Hardware & Installation Guide 4 4.1 4.2 4.3 4.3.1 4.3.2 4.3.3 Installing the LMU .................................................................................................................................. 18 Preventing Accidental or Unauthorized Modification .................................................................. 18 Installing the LMU in a vehicle ....................................................................................................... 18 Installation Verification .................................................................................................................. 20 Comm Verification ................................................................................................................. 20 GPS Verification ..................................................................................................................... 21 Inbound Verification .............................................................................................................. 22 4.3.4 Verification via SMS ............................................................................................................... 23 CalAmp Locations .................................................................................................................................. 26 License Agreement ................................................................................................................................ 27 Limited Warranty ................................................................................................................................... 32 Regulatory Information ......................................................................................................................... 35 COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 3 of 37 5 6 7 8 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 IMPORTANT: DO NOT INSTALL OR USE THE SOFTWARE OR DOCUMENTATION UNTIL YOU HAVE READ AND AGREED TO THE LICENSE AGREEMENT AND REVIEWED THE LIMITED WARRANTY AND REGULATORY INFORMATION. 1 Introduction Welcome to the LMU-3240 Hardware and Installation Guide. This manual is intended to give you information on the basic setup and installation of the CalAmp LMU-3240 product(s) including hardware descriptions, environmental specifications, wireless network overviews and device installation. 1.1 About This Manual The LMU-3240 is a full featured OBD vehicle tracking device that is optimized for a diverse range of applications including driver behavior management, car rental and automotive applications. Best suited for accessing the vehicle diagnostics interface (OBD-II) in passenger or light-duty vehicles. In order to accurately describe the functionality of these units we have broken this manual into the following sections:

System Overview A basic description of a CalAmp LMU-3240 based tracking system. This includes a description of roles and responsibilities of each of the CalAmp components as well as a brief overview of the wireless data technologies used by the LMU-3240. Hardware Overview Describes the physical characteristics and interfaces of the LMU-3240. Installation and Verification Provides guidance for the installation of the LMU-3240 in a vehicle and instructions on how to verify the installation is performing adequately. 1.2 About The Reader In order to limit the size and scope of this manual, the following assumptions have been made about the reader. You are familiar with GPS concepts and terminology You have some experience with installing equipment in vehicles You are familiar with the use of AT Commands You are familiar with the use of terminal programs such as HyperTerminal or PuTTY 1.3 About CalAmp CalAmp is a leading provider of wireless communications products that enable anytime/anywhere access to critical information, data and entertainment content. With comprehensive capabilities ranging from product design and development through volume production, CalAmp delivers cost-effective high quality solutions to a broad array of customers and end markets. CalAmp is the leading supplier of Direct Broadcast Satellite (DBS) outdoor customer premise equipment to the U.S. satellite television market. The Company also provides wireless data communication solutions for COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 4 of 37 LMU-3040 Hardware & Installation Guide the telemetry and asset tracking markets, private wireless networks, public safety communications and critical infrastructure and process control applications. For additional information, please visit the Companys website at www.calamp.com. 1.4 About the CalAmp Location Messaging Unit-LMU-3240 Revision &

Date 1.0 07/22/2019 The CalAmp Location and Messaging Unit-LMU-3240 (LMU-3240) is a mobile device that resides in private, commercial or government vehicles. The LMU-3240 is a single box enclosure incorporating a processor, a GPS receiver, a wireless data modem, and a vehicle-rated power supply. The LMU-3240 also supports inputs and outputs to monitor and react to the vehicular environment and/or driver actions. Flexibility The LMU-3240 features CalAmp's industry leading advanced on-board alert engine that monitors vehicle conditions giving you the most flexible tracking device in its class. The next generation PEG (Programmable Event Generator) script engine application supports hundreds of customized exception based rules to help meet customers' dynamic requirements. This product & platform consists of a revamped hardware, smaller form factor, a powerful Linux based embedded software environment, along with many more capabilities to-come. Customers can modify the behavior of the device to meet with a range of applications preprogrammed before shipment or in the field. Combining affordability and device intelligence with your unique application can give you distinct advantages over your competition. Seamlessly convert previous generation PEG script and upgrade to a more efficient, cost effective and robust platform, while greatly reducing maintenance efforts. Over-the-Air Serviceability The LMU-3240 also incorporates CalAmp's industry leading over-the-air device management and maintenance system software, PULS (Programming, Updates, and Logistics System). Configuration parameters, PEG rules, and firmware can all be updated over the air. Our web-based maintenance server, PULS scripts, and firmware, can all be updated over-the-

air. PULS offers out-of-the-box hands free configuration and automatic post-installation upgrades. You can also monitor unit health status across your customers' fleets to quickly identify issues before they become expensive problems. COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 5 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 2 System Overview 2.1 Overview The entire purpose behind a fleet management system is to be able to remotely contact a vehicle, determine its location or status, and do something meaningful with that information. This could include displaying the vehicle location on a map, performing an address look-up, providing real-time driving directions, updating the vehicles ETA, monitoring vehicle and driver status or dispatching the vehicle to its next pick up. These functions, of course, are completely dependent on the capabilities of the vehicle management application. The role of the CalAmp LMU-3240 is to deliver the location information when and where it is needed. A typical fleet management system based on a CalAmp device includes the following components:

A wireless data network An LMU-3240 Host Device An LM Direct communications server PULS LMU Manager version 8.9.0.2 or greater Backend mapping and reporting software which typically includes mapping and fleet reporting functions COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 6 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 2.2 Component Descriptions 2.2.1 Wireless Data Network The Wireless Data Network provides the information bridge between the LM Direct server and the LMU3240. Wireless data networks can take a variety of forms, such as cellular networks, satellite systems or local area networks. Contact the CalAmp sales team for the networks available to the LMU-3240. 2.2.2 LMU-3240 The LMU-3240 is responsible for delivering the location and status information when and where it is needed. Data requests mainly come from the following sources:

Converted PEG script within the LMU-3240 A location or status request from the LM Direct server A location or status request from LMU Manager An SMS request made from a mobile device such as a customers cell-phone In some cases, it is necessary to run an application in the vehicle while it is being tracked by the backend software. Such examples could include instant messaging between vehicles or a central office, in-vehicle mapping or driving directions, email or database access. In most of these cases you will be using the LMU-

3240 as a wireless modem as well as a vehicle-location device. 2.2.3 LM Direct Server LM Direct is a CalAmp proprietary message interface specification detailing the various messages and their contents the LMU-3240 is capable of sending and receiving. This interface allows System Integrators to communicate directly with LMU-3240's. Please refer to the LM Direct Reference Guide for details. 2.2.4 Backend Software Backend software is a customer provided software application. Regardless of its purpose, one of its primary functions is to parse and present data obtained from the LM Direct server. This allows the application to do any of the following:

Display location database on reports received from the LMU-3240 in a variety of formats Present historic information received from the LMU-3240, typically in a report/chart style format Request location updates from one or more LMU-3240s Update and change the configuration of one or more LMU-3240s COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 7 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 2.2.5 PULS PULS (Programming, Update and Logistics System) is CalAmps web-based maintenance server offering out-of-the-box hands free configuration and automatic post-installation upgrades. PULS provides a means for configuration parameters, PEG scripts, and firmware to be updated Over-The-Air (OTA) and allows CalAmp customers to monitor unit health status across your customers fleets to quickly identify issues before they become expensive problems. 2.2.6 LMU Manager LMU Manager is the primary configuration tool in the CalAmp system. It allows access to almost every feature available to the LMU-3240. Unlike the backend software, it has the option of talking directly to an LMU3240 or making a request forwarded by the LM Direct server. For further details on using LMU Manager, please refer to the LMU Manager Users Guide. 2.2.7 Wireless Data Network The Wireless Data Network provides the information bridge between the LM Direct server and the LMU3240s. Wireless data networks can take a variety of forms, such as cellular networks, satellite systems or local area networks. At this point in time, the networks available to the LMU-3240 are:

LTE (Long-Term Evolution) Long-term evolution (LTE) is the latest and rapidly growing global data transmission technology. Based on GSM and UMTS/HSPA standards, LTE is a standard of high-speed wireless data transmission and communication. Continuously evolving, LTE advancements continue to push data capacity and user experience on a global scale. With a peak downlink rate of 300 mbps, uplink rate of 75 mbps, LTE sits in 1.4 MHz to 20 MHz bands, while also supporting FDD, TDD, and not sacrificing data capability. 2.2.8 LMU-3240 The LMU-3240 is responsible for delivering the location and status information when and where it is needed. Data requests can come from any of the following sources:

PEG script within the LMU-3240 A location or status request from the LM Direct server A location or status request from LMU Manager A request made from a host device such as a laptop, PDA or MDT COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 8 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 3 PEG Conversion Reference the PEG to PEG Script conversion guide to integrate existing script into the next generation format. Note that only LMU-3240 device script is currently supported by the conversion process other device script may not function as intended. Consult with your FAE support regarding PEG to PEG Conversion inquiries. 3.1 Getting Started It is recommended to conduct testing and validation on one unit before deploying on to a larger fleet. 1. Select a script (use case) based on PEG support available in LMU-3240 2. We highly encourage you to share the following information with your FAE to get timely support on possible issues o Script to be used. o YMM of chosen vehicles. o List of vehicle parameters (PIDs) 3. Convert your current PEG script to PEG2 format using LMU Manager 8.9 or later. Refer to conversion guide for help. You may have to make some changes manually in PEG1 format to get your conversion right. 4. Assign PEG2 (.pg2) script through PULS o Go to Other Files under Firmware drop-down o Choose Device Type as LMU, and File type as PEG2 5. Install SIM cards and install the devices in your vehicles. 3.2 Setup & Equipment To properly set up the LMU-3240, users will need access to and have knowledge of the following items;

Device Sims: 4ff (Nano) AT&T Sim Device Management: https://puls.calamp.com/devicemgr/

3.2.1 Serial Communication o Serial Cable: Micro USB B cable (male). Example: StarTech P/N: UUSBHAUB3 o Windows PC or Linux o SSH tool: E.g. Putty (see login instructions below) o Power Supply o OBD Power cable 3.2.2 Login (SSH) Instructions:

o Open a SSH program (e.g. Putty) o Enter in Host: 192.168.225.1 COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 9 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 o Enter Port: 22 o Username: calamp o Password: welcome123 o Type atcon to start the debug session 4 Hardware Overview 4.1 Location Messaging Unit-LMU-3240 4.1.1 LMU-3240 Handling Precautions Electrostatic Discharge (ESD) Electrostatic discharge (ESD) is the sudden and momentary electric current that flows between two objects at different electrical potentials caused by direct contact or induced by an electrostatic field. The term is usually used in the electronics and other industries to describe momentary unwanted currents that may cause damage to electronic equipment. ESD Handling Precautions ESD prevention is based on establishing an Electrostatic Protective Area (EPA). The EPA can be a small working station or a large manufacturing area. The main principle of an EPA is that there are no highly charging materials in the vicinity of ESD sensitive electronics, all conductive materials are grounded, workers are grounded, and charge build-up on ESD sensitive electronics is prevented. International standards are used to define typical EPA and can be obtained for example from International Electro-technical Commission (IEC) or American National Standards Institute (ANSI). This ESD classification of the sub assembly will be defined for the most sensitive component, therefore the following classifications apply:

Class 1B Human Model (< 1 kV) Class M1 Machine Model (< 100V) When handling the LMU-3240s main-board (i.e. sub assembly) by itself or in a partial housing proper ESD precautions should be taken. The handler should be in an ESD safe area and be properly grounded. GPS Ceramic Patch Handling When handling the sub assembly it may be natural to pick it up by sides and make contact with the antenna boards. In an uncontrolled ESD environment contact with the center pin of ceramic patch antenna can create a path for electrostatic discharge directly to the GPS Module. The GPS Module is very sensitive to ESD and can be damaged and rendered non-

functional at low levels of ESD. One should avoid contact with the center pin of the patch during handling. Packaging COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 10 of 37 Electrical Over-Stress (EOS) Storage and Shipping LMU-3040 Hardware & Installation Guide Anytime the sub assembly is shipped and it is not fully packaged in its final housing it must be sealed in an ESD safe bag. Revision &

Date 1.0 07/22/2019 The GPS receiver can be damaged if exposed to an RF level that exceeds its maximum input rating. Such exposure can happen if a nearby source transmits an RF signal at sufficiently high level to cause damage. One potential source of EOS is proximity of one LMU-3240 GPS Antenna to another LMU-3240 GSM Antenna. Should one of the units be in a transmit mode the potential exists for the other unit to become damaged. Therefore any LMU-

3240 GPS Antenna should be kept at least four inches apart from any active LMU-3240 GSM Antenna or any other active high power RF transmitter with power greater than 1 Watt. 4.1.2 Battery Back-up devices Please properly dispose of the battery in any of the CalAmp products that utilize one, do not just throw used batteries, replaced batteries, or units containing a back-up battery into the trash. Consult your local waste management facility for proper disposal instructions. COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 11 of 37 Revision &

Date 1.0 07/22/2019 LMU-3040 Hardware & Installation Guide 4.1.3 Environmental Specifications The LMU-3240 is designed to operate in environments typically encountered by fleet vehicles, including wide temperature extremes, voltage transients, and potential interference from other vehicle equipment. To ensure proper operation in such an environment, the LMU-3240 was subjected to standard tests defined by the Society of Automotive Engineers (SAE). The specific tests included temperature, shock, vibration, and EMI/EMC. These tests were performed by independent labs and documented in a detailed test report. In accordance with Appendix A of SAE J1113 Part 1, the Unit is considered a Functional Status Class B, Performance Region II system that requires Threat The following shows the environmental conditions the LMU is designed to operate in and the relevant SAE tests that were performed. No formal altitude tests were conducted. Level 3 Testing. Dimensions Weight 2.54 oz. (72 g) Temperature 1.88 x 2.50 x 1.14 (48 x 63.25 x 29 mm)

-30 to +60 C (connected to primary power)

-10 to +60 C (operating on internal battery)

-20 to +25 C 6 months (long term storage) COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 12 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 Humidity 0% to 95% relative humidity, at 50 C non-condensing Shock and Vibration SAE Test: SAE J1455 Compliant Mil Standard 202G and 810F Compliant Ground vehicle environment with associated shock and vibration Electromagnetic Compatibility (EMC/EMI) IEC 61000-4-2 (4KV Test) Operating Voltage Range 12-24 VDC Vehicle Systems 9-30 VDC (start-up, operating) 7-32 VDC (momentary) Power Consumption Typical 1 mA @ 12V (deep sleep) Typical 10 mA @ 12V (sleep on active network) Typical 70 mA @ 12V (active tracking with GPS and cell enabled) Satellite Location (GNSS) Hybrid GPS, GLONASS, SBAS Engine

(WAAS, EGNOS, MSAS) 55 channel GPS Receiver Tracking Sensitivity

-157 dBm (hot start)

-148 dBm (cold start)

~2.0m CEP Open Sky (GPS SBAS 24 hours static) COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 13 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 Acquisition Sensitivity

-167 dBm tracking sensitivity Communications (Comm) Operating Bands (MHz) North America Variant I:

LTE Cat1: 1900 (B2)/AWS 1700 (B4)/850 (B5)/700 (B12) MHz HSPA/UMTS: 850 (V)/1900 (II) MHz North America Variant II:

LTE Cat1: AWS 1700 (B4)/700 (B13) MHz Data Support SMS, UDP Packet Data, TCP, TLS, CalAmp Telematics Cloud API 4.2 LMU-3240 Connectors 4.2.1 Primary Connector The LMU-3240 equips a 16-Pin J1962 Compliant OBD-II Plug that also supports the following OBD-II physical layer interfaces:

1. ISO 15765 CAN COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 14 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 2. 3. ISO 9141-2 K-Line ISO 14230 KWP2000]

4. J1850 PWM 5. J1850 VPW Connector on Vehicle side Please note that only 13 out of the 16 connector pins are actually populated on the connector. Connector on LMU-3040 side Pin Signal Name Description 1 Make/Model Specific Vendor Option 2 Bus+ Line SAE-J1850 PWM and SAE-1850 VPW 3 Make/Model Specific Vendor Option 4 Chassis Ground Ground 5 Signal Ground Ground Can High ISO 15765-4 and SAE-J2284 K line ISO 9141-2 and ISO 14230-4 6 7 COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 15 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 8 Make/Model Specific Vendor Option 10 Bus- Line SAE-J1850 PWM and SAE-1850 VPW 11 Make/Model Specific Vendor Option 14 Can Low ISO 15765-4 and SAE-J2284 15 L line ISO 9141-2 and ISO 14230-4 16 Battery Power Power 4.2.2 Serial Adapter Depending on the variant of the LMU3240, the LMU-3240 may or may not have an external serial connector. If it does not have a serial connector as shipped, the LMU 3240 requires additional steps in order to use a serial connector. Please contact your FAE for steps on how to do this. 4.2.3 Accessories See the Harness Diagrams page for more information on LMU accessories, and supported products table The LMU-3240 provides the following Inputs for scripting purposes, but there are no selectable inputs on the device Input 1: Motion Sensor (low = no motion, high = motion) Input 2: Power State (low = main power, high = battery power) Input 3: Vbatt Low Input 4: Vin Active (On LMU-3240 use Input 4 for Ignition Input Wake Up Monitor instead of Input 4.3 I/O Descriptions Digital Inputs Input 0: Engine ON 0) Analog to Digital Inputs A/D 0: Vin COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 16 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 A/D 1: uP Temp A/D 2: Vref A/D 3: Battery A/D 4: Impact Outputs Output 4: Power Supply Switch (cleared = switch to external power, set = switch to internal power) Output 5: Enable/Disable Battery charging (cleared = enable battery charging, set = disable battery charging) 4.3.1 3-Axis Accelerometer + 3-Axis Gyroscope The LMU-3240 supports an internal 3 Axis Precision Accelerometer as one of its discreet inputs. When the LMU is moved in any direction, the associated input will be in the High state. If the LMUs accelerometer does not detect motion, then the input will be in the Low state. No external connections are required for this functionality to be operational. Accelerometer Acquisition rate: >1600Hz Sampling rate - output data rate: 100, 200, 400 Hz Resolution: <= 0.01G Full Scale: 15-24G Gyroscope Acquisition rate: >1600Hz Sampling rate - output data rate: 100, 200, 400 Hz Resolution: <= 0.01G Full Scale: 15-24G 4.3.2 Status LEDs the table below:

The LMU-3240 contains one programmable dual-color status LED (amber and green). Please note that there are PEG configuration parameters that can change the factory default behavior of all LEDs. LED behavior detail can be reviewed in COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 17 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 LED Definitions and Behavior Condition Order LED Color LED Frequency Power On 1 Amber/Green Fast GPS On GPS Time Sync 2 2 GPS Fix 2 Comms On & Searching 3 Network Available 3 Green Green Green Amber Amber Amber Slow blinking Fast blinking Solid for 10 s Slow blinking Fast blinking Registered but no inbound acknowledgement 3 Solid & Fast Blink every 1 s Registered and received inbound acknowledgement 3 Amber Solid for 10 s Vehicle Not Compatible 4 Amber/Green Slow Install Successful 5 Green Solid 5 Installing the LMU 5.1 Preventing Accidental or Unauthorized Modification If you anticipate that fleet drivers or others might interfere with the LMUs once they are installed, take steps to be sure that it is not easy to remove the LMU from its power source, etc. Two common methods are the use of Tamper Proof Sealant or creation of PEG Script to detect power loss or GPS antenna disconnections. 5.2 Installing the LMU in a vehicle 1. Make sure the vehicle is turned on/running when plugging in the unit. If the unit is plugged in while the vehicle is off it will need to complete the detection process on the next ignition on cycle in order to operate correctly. 2. Plug the unit into the OBD2 connector of the vehicle while it is running, and do NOT turn off the ignition. COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 18 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 3. Leave the unit plugged in with vehicle ignition on until the detection process has completed. Vehicle detection status can be checked through SMS over the air or with AT Commands using the CalAmp serial connection cable. The AT Command to check vehicle detection status. The vehicle detection complete response will look like:

ATIV

-Vehicle Detection-

Detection Complete VIN: <Vehicle Vin Number>

OBDII Protocol:5 Params:0,1,4,7,8,11,12

!VV Yes Proto:5

- Veh Det -

VIN:<Vehicle Vin Number>

Params:0,1,4,7,8,11,12 Indicators:0(000000000011),1(11111111111) The SMS command to check vehicle detection status:

The vehicle detection complete response will look like:

COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 19 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 Inds:0(000000000011),1(11111111111) DTCs Cnt:7 Flt Mtch:1 4. Once the vehicle detection has completed the vehicle ignition can then be turned off. 5.3 Installation Verification In many cases it is desirable to verify that an installed LMU-3240 is working properly. That is, installers should verify that the GPS and communications functions of the LMU-3240 are working properly before departing the installation site. In more robust cases, some key configuration settings such as the Inbound Address and URL should also be verified. Note that these processes are all based on issuing AT Commands to the LMU-3240. It is expected that installers will have access to a serial port expansion cable and a laptop or PDA capable of a terminal connection. Alternatively, an SMS message can be sent to an LMU-3240 to obtain its current status. 5.3.1 Comm Verification Installers should first verify that the LMU-3240 has been acquired and has registered to the wireless network. This may be verified in one of two ways. First, installers may look at the LED. If this LED is solid, then the LMU has registered to the network and established a data session. If the LED is not visible, then Comm may be verified using an AT Command:

Depending on the wireless network being used something similar to what is shown below will be displayed. It is important to verify that 'Yes' values are displayed at the top for Data and Network registration and the correct APN is displayed. Radio Access : LTE Network Reg. : Yes, Home Data Reg. : Yes, ATIC Home COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 20 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 Connection : Yes RSSI : -97 dBm BER : 99 Channel : 737 Cell ID : 3441 Base Station ID : 40 Local Area Code : 31003 Network Code : 410 Country Code : 310 IMEI (Modem S/N): 351802055396182 IMSI (SIM ID) : 310410202524377 ICC-ID (SIM S/N):

89014102212025243778 Phone Number :

GPRS APN : ISP.CINGULAR Maint. Server :

maint.vehiclelocation.com(216.177.93.246):20500 Inbound Server : (0.0.0.0):20500 Dual Comm : routing id=0, log cid=0, modem type=21, inbnd index=0 OK the wireless network. 5.3.2 GPS Verification AT$APP GPS?

If any of the responses return Not-Acquired or Not-Registered (and the APN is correct), the wireless network operator should be contacted for further troubleshooting. Please note that it may take several seconds (or longer) for the LMU-3240 to communicate with the modem and acquire The next step is to verify that the GPS receiver is seeing enough satellites to obtain a valid GPS position. Again, installers have two choices on how to perform this verification. First, like the Comm Verification, there is a GPS status LED (i.e., the one closest to the SMA connector). If this LED is solid, then the LMU has found GPS service. If the LED is not visible then GPS service may be verified using an AT Command:

COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 21 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 The response should be similar to:

Lat=3304713, Lon=-11727730, Alt=0 Hdg=113 Spd=0 3D-RTIME HDOP=130 nSats=7 Installers are looking for the 3D-RTIME setting along with a valid Lat, Long pair (i.e. something other than 0). If the GPS receiver does not have a valid lock within 2-3 minutes, installers should check antenna placement (see the Installation Notes section for placement suggestions), the antenna connector and that the antenna has a clear view of the sky. For further troubleshooting, installers should contact CalAmp Support (productsupport@CalAmp.com) 5.3.3 Inbound Verification The last item to verify is that the LMU-3240 is sending data to the correct server. In general, this is a two-step process that will need the aid of an observer on the back end. That is, a technician will have to be logged in so they can monitor data coming into the backend mapping/vehicle management application. First, verify that the LMU-3240 is using the correct Inbound IP address by using:

AT$APP INBOUND?

The response should be similar to:

INBOUND LMD INBOUND 0 ADDR ddd.ddd.ddd.ddd:ppppp *

INBOUND 0 URL myURL.myCompany.com INBOUND 1 ADDR 0.0.0.0:20500 INBOUND 1 URL INBOUND 2 ADDR 0.0.0.0:20500 INBOUND 3 ADDR 0.0.0.0:20500 The installer will need to verify with a backend technician that the, URL (myURL.myCompany.com ), IP address

(ddd.ddd.ddd.ddd) and port (<ppppp>) are correct. The second step is to verify that the LMU-3240 is sending data. The best way to do this is to force the LMU-

3240 to send in an unacknowledged Event Report (i.e., its current GPS location) with the following command:

COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 22 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 AT$APP PEG SUNRPT 255 The LMU-3240 will respond with: OK

!R0 The backend monitor must then be contacted to confirm that they received an Event Report with Event Code 255. Assuming that all three sections have passed, the installation can be considered to be complete. The current Comm, GPS and Inbound status of a LMU can be obtained via SMS provided you have access to an SMS 5.3.4 Verification via SMS capable phone or PDA. Using your handset, send the following SMS Message to the LMU:

Within a few minutes, the LMU should return a response in the following format:

APP: <App ID> <Firmware Version>

COM:<RSSI> [./d/D][./a/A][./L][IP address] [<APN>]

GPS:[Antenna <Short/Open/Off>] | [No Time Sync] | [<FixStatus> <Sat Count>]

INP:<inputs states> <vehicle voltage>

MID:<mobile ID> <mobile ID type>

INB:<inbound IP address>:<inbound port> <Inbound Protocol (LMD/LMX)>

ID>:

APP: o <App The current firmware version in use by the LMU o <Firmware Version>:

COM:

o <RSSI>:

The Application ID value of the LMU indicating the host platform and the wireless networking technology of the LMU. COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 23 of 37 LMU-3040 Hardware & Installation Guide This is the signal strength the wireless modem sees from the network. In general the LMU is at least scanning for the Revision &

Date 1.0 07/22/2019 network if the RSSI is not -113. o [./d/D]:

If the character D is present, it indicates the LMU had a data session established when it responded to the status request. For the 8-Bit product line an upper case D indicates both the Inbound and Maintenance sockets are ready. The lower case d indicates that only the Maintenance socket is ready. A . indicates no sockets are ready. This field indicates if the LMU has received an Acknowledgement from the Inbound server. This field will be empty if the LMU has never received an ACK. The lower case a will be present if it has received an ACK since the last cold boot (i.e. power cycle) but not the last warm boot (App Restart or Sleep). The upper case A will be present if the LMU has received an ACK since the last warm boot. A . Indicates no acknowledgement has been received. This field indicates if the LMUs log is currently active. An L indicates that the log is currently in use (i.e. one or more records have been stored) where a . indicates the log is inactive. This is an optional field if and is only present if the LMU has established a valid data session. This field will contain the current IP address of the LMU as assigned by the wireless network. Note that if you see a value of 192.168.0.0, this is an indication that the LMU has not been able to establish a data session. o [./a/A]:

o [./L]:

o [IP Address]:

o [<APN>]

The current Access Point Name in use by a GSM LMU. o [Antenna <Short/Open/Off>]:

GPS:

This field, if present, indicates a problem with the LMUs GPS antenna. A value of Short indicates that the antenna cable has likely been crushed. A value of Open indicates that the antenna cable is either cut or disconnected. A value of Off indicates that the LMU GPS receiver is off. o [No Time Sync]:

If this field is present, it indicates that the LMUs GPS receiver has not been able to find even a single GPS satellite. This would likely been seen in conjunction with the above antenna error, or if the LMU GPS antenna is otherwise blocked. o [<FixStatus> <Sat Count>]:

COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 24 of 37 LMU-3040 Hardware & Installation Guide If these fields are present it indicates that the LMU has, or had a valid GPS solution. The <Sat Count> field indicates how many GPS satellites are currently in use by the LMU. The <FixStatus> field indicates the type of fix. The Fix Status types are detailed in the LM Direct Reference Guide. Revision &

Date 1.0 07/22/2019 o <input states>:

INP:

This field details the current state of each of the LMUs discreet inputs. This field is always 8 characters long. The left most character represents the state of input 7 where the right most represents the state of input 0 (i.e. the ignition). A value of 1 indicates the input is currently in the high state. A value of 0 indicates it is currently in the low state. This field will contain the current reading of the LMUs internal A/D. This will be the supply voltage provided to the LMU in mV. MID:

This will be the current mobile ID in use by the LMU. This will be the type of Mobile ID in use by the LMU. The available types are, Off, ESN, IMEI, IMSI, USER, MIN and IP ADDRESS. INB:

This is the current IP address in use by the LMU. This value should match the IP address of your LM Direct server. This is the current UDP port the LMU will use to deliver its LM Direct data. This value should match UDP port you are using on your LM Direct server. It is typically 20500. o <Inbound Protocol (LMD/LMX)>:

This is the current UDP/IP messaging protocol in use by the LMU. In general it should be LMD. o <vehicle voltage>:

o <mobile ID>:

o <mobile ID type>:

o <inbound IP address>:

o <inbound port>:

Example Response APP:081 8.3d COM:0 GPS:No Time Sync INP:11100111 13.7V MID:4141000100 ESN COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 25 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 INB:207.7.101.227:20500 LMD 6 CalAmp Locations United States as well as internationally. CalAmp's corporate headquarters is located in Irvine, CA, with many divisional and satellite locations across the Corporate Headquarters 15635 Alton Parkway, Suite 250 Irvine, CA 92618 Additional Locations 1401 North Rice Avenue Oxnard, CA 93240 6551 City West Parkway Eden Prairie, MN 55344 2177 Salk Avenue, Suite 200 Carlsbad, CA 92008 40 Pequot Way Canton, MA 02021 13655 Dulles Technology Drive, Suite 200 Herndon, VA 20171 5th Floor Five Lamps Place 77-80 Amiens, Street Dublin 1 D01 A7V2 Republic of Ireland COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 26 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 7 License Agreement FOR SOFTWARE, APPLICATION PROGRAMING INTERFACES (APIs) & DOCUMENTATION IMPORTANT: DO NOT INSTALL OR USE THE SOFTWARE OR DOCUMENTATION UNTIL YOU HAVE READ AND AGREED TO THIS LICENSE AGREEMENT. This is a legal agreement between you, the Customer, and CalAmp DataCom Incorporated (CalAmp). By installing and/or using the software or documentation, you are consenting to the terms of this License. If you do not agree to the terms of this non-exclusive License Agreement, DO NOT INSTALL OR USE THE SOFTWARE, APIs OR DOCUMENTATION. For a full refund, return the unused media package and all accompanying materials within seven (7) days to CalAmp. Where there is no packaging or media, use of the software and/or documentation constitutes acceptance. Definitions: As used in this License Agreement, Software means CalAmps LM Direct , LMU Manager, LapTop Locator, LMU Application/Programmable Event Generator, CDMA LMU Provisioning Tool, GPRS LMU Provisioning Tool, iDEN Provisioning Tool, LMU Status, Clone Config, Hex Dump, LM Exchange Traffic Monitor, Freewave Base Station Config, Remote Serial Port, App Watcher Service and/or other software products licensed by CalAmp for use in computer applications development or integration including the computer programs, libraries and related materials either contained on the media provided to you by or from CalAmp, or which you have received or downloaded electronically. Application means a compiled or executable software program created by Developer that uses some or all of the functionality of the Software. Software Copies means the actual copies of all or any portion of the Software including backups, updates, merged or partial copies permitted hereunder or subsequently licensed to you. Documentation means the non-Software information contained on the media provided with this package or downloaded and which is used with and describes the operation and use of the Software. Documentation Copies means the actual copies of all or any portion of the Documentation including backups, updates, merged or partial copies permitted COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 27 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 hereunder or subsequently provided to you. Related Materials means all other materials and whatever is provided by or from CalAmp, and the non-Software and non-Documentation contained on the media supplied, downloaded, or otherwise supplied by or from CalAmp for use with the Software and Documentation. Server means a single, networked computer that is accessible to other client machines on the network. User means (i) a single person using an Application for his/her internal, use or (ii) a single terminal or a single workstation of a computer used only by a person (and not accessed otherwise) for accessing an Application. Use License means limited rights granted by CalAmp for deployment of a single Application to a User. Developer means a single programmer developing an Application. Developer License means the grant of certain limited rights to use and maintain the Software, Software Copies, Documentation, Documentation Copies and Related Materials in development of Applications. Background: A Developer License is required for each Developer who uses the Software in building Application(s). A Use License is required and must be purchased by Customer for each User to which Customer provides access to an Application (unless a Server or Site license for unlimited or a specified number of users has been purchased). Each Use License is specific to one client-side Application only and may not be used for any other client-

side Application. Each Server license is limited to Server-based Applications deployed on that Server for which the license has been purchased as specified in a CalAmp License Certificate. The Software is licensed on a per Developer, and on a per User, per Application basis. In order to preserve and protect its rights under applicable law, CalAmp is not selling you ownership rights to Software or Documentation (owned by or licensed to CalAmp). CalAmp specifically retains title to all CalAmp Software, Documentation and Related Materials and CalAmp licensors retain title to items owned by them. Duration: This License Agreement is effective from the day you install or start using the Software, or receive or download it electronically, and continues until terminated. If you fail to comply with any provision of the License, termination is automatic, without notice from CalAmp and without the necessity for recourse to any judicial authority. Upon termination, you must destroy the Related Materials, the Software, Documentation and all Software and Documentation copies. CalAmp can also enforce its other legal and equitable rights. Developer License OnlyUses Permitted: Software and Documentation may be used for the sole purpose of developing Applications and only by a licensed Developer. Software and Documentation may be installed onto a hard disk drive or a Server, access to which is restricted to Developers for which a Developer License has been purchased and may also be stored or installed on a storage device such as a network server, used only to install or access the Software or COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 28 of 37 LMU-3040 Hardware & Installation Guide Documentation on your other computers over an internal network; however, you must have acquired a license for each separate computer on which the Software or Documentation is installed or accessed from the storage device. A Developer License may not be shared or Revision &

Date 1.0 07/22/2019 COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 29 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 used concurrently on different computers. One backup copy may be made for each legally obtained media copy or electronic copy you have received, provided that all CalAmp and third party licensor information including copyright notices are maintained and possession of the copy is retained in a secure location. In addition, you agree to use reasonable efforts to protect the Software and Documentation from unauthorized use, reproduction, distribution or publication. All rights not specifically granted in this License are reserved by CalAmp. Customer agrees to include the notice Copyright 1999 2009 CalAmp DataCom Inc., All Rights Reserved in Applications developed with the Software. Customer agrees to include the following CalAmp Copyright and Government Restricted Use notice in all documentation and in any Application on-line help or readme file. Portions of this computer program are owned by CalAmp DataCom Inc., Copyright l999 2009, CalAmp DataCom Inc., All Rights Reserved. Use, duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph

(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 or subparagraphs (l) and

(2) of the Commercial Computer Software-Restricted Rights at 48 CFR 52.227-19, as applicable. Manufacturer is CalAmp DataCom Inc., 1401 North Rice Ave. Oxnard, CA 93240. Rights are reserved under copyright laws of the United States with respect to unpublished portions of the Software. Developer(s) LicenseUses Not Permitted: Unless Otherwise Agreed To In Writing with CalAmp, You May Not (1) Make derivative works including but not limited to translations, adaptations, arrangements or any other alteration (each of which would become the property of CalAmp or its licensors, as applicable) or make copies of the Software or Documentation except as permitted above; (2) Make copies of the Related Materials; (3) Use any CalAmp product to translate the product of another licensor unless you have the legal right to do so; (4) Allow a greater number of Developers to access the Software at any one time than the total number of Developer licenses for which you have paid; (5) Rent, lease, sublicense or lend the Software, Software Copies, Documentation, Documentation Copies, Related Materials or your rights under this License or allow access to the Software for unlicensed users; (6) Alter, decompile (except to the limited extent that decompilation by the licensed Developer only is necessary as the only available way to achieve interoperability with other programs and, in that situation, any resulting information cannot be used in developing, producing or marketing any software substantially similar in expression to the Software), disassemble or reverse engineer the Software; (7) Make any attempt to unlock or bypass any initialization system or encryption techniques utilized by the Software or Documentation; (8) Alter, remove or obscure any proprietary legend, copyright or trademark notice contained in or on Software, Documentation or Related Materials; or (9) use the Software to create an Application intended solely to duplicate functionality of an existing CalAmp COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 30 of 37 end user software product. Revision &

Date 1.0 07/22/2019 LMU-3040 Hardware & Installation Guide Use Licenses: For each Server or Site License purchased, CalAmp grants the Customer the right to distribute Applications on a single Server or at a single Site, as the case may be, accessible to the number of individual users (not concurrent users) for which the Server or Site License has been purchased as evidenced by a CalAmp License Certificate. For each Use License purchased, as evidenced by a CalAmp License Certificate, CalAmp grants the Customer the right to distribute a single Application to a single User. In no circumstance may Customer distribute an Application under a site license or concurrent use license unless a comparable license has been purchased for the Software as evidenced by a CalAmp License Certificate. Customer agrees that distribution of an Application to a User will in all cases be accompanied by a license agreement containing at a minimum terms and conditions substantially similar to and at least as restrictive as the following:

The User may not (1) Make derivative works including but not limited to translations, adaptations, arrangements or any other alteration of the Application or make copies of the Application, except one backup copy may be made for each legally obtained copy of the Application, provided that all CalAmp and third party licensor information including copyright notices are maintained and possession of the copy is retained in a secure location; (2) Allow access to the Application for unlicensed users; (3) Rent, lease, sublicense or lend the Application or its rights under the license; (4) Alter, decompile, disassemble or reverse engineer the Application; (5) Make any attempt to unlock or bypass any initialization system or encryption technique utilized by the Application; or (6) Alter, remove or obscure any proprietary legend, copyright or trademark notice contained in or on the Application. The User agrees to use reasonable efforts to protect the Application from unauthorized use, reproduction, distribution or publication. Audit: Customer shall keep records of all transactions involving Software for five (5) years after the transaction. CalAmp shall have the right upon written notice to audit Customers records to verify compliance with this License including the number of Use Licenses granted by Customer. Audit may take place at Customers place or business during normal working hours. In the event that there is a discrepancy in excess of five percent (5%) between the number of Use Licenses granted and the number paid for, Customer shall pay all costs related to performing the audit in addition to remitting payment for those licenses granted in excess of those paid for as evidenced by a CalAmp License Certificate. General: This Agreement represents our entire understanding and agreement regarding the Software, COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 31 of 37 LMU-3040 Hardware & Installation Guide Software Copies, Documentation, Documentation Copies and Related Materials and supersedes any prior purchase order, communication, advertising or representation and may only be modified in a written amendment signed by an authorized CalAmp representative or by a specific prior or subsequent written agreement between the parties. If any provision of this Agreement shall be unlawful, void or for any reason unenforceable, that provision shall be deemed severable from, and shall in no way affect the validity or enforceability of, the remaining provisions. Revision &

Date 1.0 07/22/2019 8 Limited Warranty Covering the Physical Media and Printed Materials: CalAmp warrants to you, the original licensee, that the media on which the Software is recorded are free from defects in materials and workmanship under normal use and service FOR A PERIOD OF NINETY (90) DAYS FROM THE DATE OF DEVELOPER LICENSE PURCHASE. CalAmps entire liability and your exclusive remedy as to defective media, Documentation or Related Material(s) shall be replacement of the media, Documentation or Related Material(s) by CalAmp. Each defective item, along with proof of license purchase and date, must be sent in a traceable manner to: CalAmp DataCom Inc., 1401 North Rice Ave. Oxnard, CA 93240. Disclaimer Regarding the Software, Documentations and Related Materials: THE SOFTWARE, DOCUMENTATION AND RELATED MATERIALS ARE PROVIDED AS IS. EXCEPT AS MAY OTHERWISE BE EXPRESSLY SET FORTH HEREIN, CALAMP MAKES NO REPRESENTATIONS OR WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO THE SOFTWARE, DOCUMENTATION OR RELATED MATERIALS INCLUDING BY WAY OF EXAMPLE, AND NOT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. BY WAY OF FURTHER EXAMPLE AND NOT LIMITATION, CALAMP MAKES NO REPRESENTATIONS OR WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO THE ACCURACY, RELIABILITY OR COMPLETENESS OF THE DOCUMENTATION OR THE RELATED MATERIALS. THE ENTIRE RISK AS TO THE USE OF THE SOFTWARE, DOCUMENTATION AND RELATED MATERIALS IS ASSUMED BY YOU. IN NO EVENT SHALL CALAMP BE LIABLE TO YOU OR ANY OTHER PERSON, REGARDLESS OF THE CAUSE, FOR THE EFFECTIVENESS OR ACCURACY OF THE SOFTWARE, DOCUMENTATION OR RELATED MATERIALS OR FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM OR OCCASIONED BY YOUR USE OF THE SOFTWARE, DOCUMENTATION OR RELATED MATERIALS, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN THE EVENT THE FOREGOING IS FOUND BY A COURT OF COMPETENT JURISDICTION TO BE INEFFECTIVE, YOU HEREBY AGREE THAT CALAMPS COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 32 of 37 LMU-3040 Hardware & Installation Guide MAXIMUM LIABILITY FOR ANY CLAIM ARISING IN CONNECTION WITH THE SOFTWARE, DOCUMENTATION AND/OR RELATED MATERIALS (WHETHER IN CONTRACT, TORT, INCLUDING NEGLIGENCE, PRODUCT LIABILITY OR OTHERWISE) SHALL NOT EXCEED THE LICENSE FEES PAID Revision &

Date 1.0 07/22/2019 COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 33 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 BY YOU WITH RESPECT TO THE SOFTWARE, DOCUMENTATION AND/OR RELATED MATERIALS AT ISSUE. SOME STATES DO NOT ALLOW THE LIMITATION OR EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE FOREGOING PROVISION, WITH RESPECT TO EXCLUDING OR LIMITING SUCH DAMAGES, MAY NOT APPLY TO YOU. Acknowledgement: You acknowledge that you have read this LIMITED WARRANTY, understand it and agree to be bound by its terms and conditions. You also agree that: (1) No oral or written information or advice given by CalAmp, its dealers, distributors, agents or employees shall in any way increase the scope of this Limited Warranty and you may not rely on any such information or advice; (2) Unless a written governing agreement signed by you and CalAmp exists, this License Agreement is the complete and exclusive statement of agreement between CalAmp and you regarding the licensing of the Software, Documentation and Related Materials and supersedes all proposals, oral or written, and any other communications you may have had prior to purchasing your license; (3) Except for the price and delivery terms agreed upon by both parties, the terms and conditions of this License Agreement shall supersede those set forth in any purchase order where the purchase order conflicts or is inconsistent with or adds to the terms and conditions of this License and those superseded purchase order terms and conditions shall be null and void; (4) You agree to assure that copies of this License Agreement are distributed, read and agreed to by each Developer using the Software and/or Documentation. Governing Law: This Agreement shall be governed by the laws of the State of California, United States, excluding its conflicts of law principles and excluding the United Nations Convention on Contracts for the International Sale of Goods. You agree to exclusive jurisdiction of California State federal and state courts, Ventura County, for resolution of any dispute related to this Agreement. U.S. Government Protected Rights: The Software Documentation and Related Materials are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph (1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-

7013 or subparagraphs (1) and (2) of the Commercial Computer Software-Restricted Rights at 48 CFR 52.227-19, as applicable. Manufacturer is CalAmp DataCom Inc., 1401 North Rice Ave. Oxnard, CA 93240. Rights are reserved under copyright laws of the United States with respect to unpublished portions of the Software. COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 34 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 9 Regulatory Information Human Exposure Compliance Statement Pursuant to 47 CFR 24.52 of the FCC Rules and Regulations, personal communications services (PCS) equipment is subject to the radio frequency radiation exposure requirements specified in 1.1307(b), 2.1091 and 2.1093, as appropriate. CalAmp DataCom Inc. certifies that it has determined that the LMU-3240 complies with the RF hazard requirements applicable to broadband PCS equipment operating under the authority of 47 CFR Part 24, Subpart E of the FCC Rules and Regulations. This determination is dependent upon installation, operation and use of the equipment in accordance with all instructions provided. The LMU-3240 is designed for and intended to be used in fixed and mobile applications. Fixed means that the device is physically secured at one location and is not able to be easily moved to another location. Mobile means that the device is designed to be used in other than fixed locations and generally in such a way that a separation distance of at least 20 cm is normally maintained between the transmitters antenna and the body of the user or nearby persons. The LMU-3240 is not designed for or intended to be used in mobile applications (within 20 cm of the body of the user) and such uses are strictly prohibited. To ensure that the LMU-3240 complies with current FCC regulations limiting both maximum RF output power and human exposure to radio frequency radiation, a separation distance of at least 20 cm must be maintained between the units antenna and the body of the user and any nearby persons at all times and in all applications and uses. Additionally, in mobile applications, maximum antenna gain must not exceed 3.2 dBi. FCC Rules and Industry Canada (IC) regulatory information Compliance Statement (Part 15.19) interference that may cause undesired operation. Warning (Part 15.21) The equipment device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received including COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 35 of 37 LMU-3040 Hardware & Installation Guide this equipment. Changes or modifications not expressly approved by TransCore Amtech Systems could void the users authority to operate the equipment. Manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to Revision &

Date 1.0 07/22/2019 Compliance Statement (Part 15.105(b)) Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Class B digital device notice CAN ICES-3 (B)/NMB-3(B) RF Radiation Exposure Statement except tested built-in radios. person/user. This equipment complies with the FCC/IC radiation exposure limits set fourth for mobile transmitting devices operation in an uncontrolled environment. End users must follow the specific operating instructions to satisfy RF exposure compliance. The equipment should only be used where there is normally at least 20cm separation between the antenna and all This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 36 of 37 LMU-3040 Hardware & Installation Guide Revision &

Date 1.0 07/22/2019 Dclaration d'exposition aux radiations:

Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Cet appareil et son antenne ne doivent pas tre situs ou fonctionner en conjonction avec une autre antenne ou un autre metteur, exception faites des radios intgres qui ont t testes. COMPANY CONFIDENTIAL: CalAmp reserves all rights to these documents and any information contained therein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. 2018 CalAmp Page 37 of 37