WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6363159.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case CMP40x0 (Model: CEL8721D) Hostless Dual-Band Wi-Fi + BLE Module Datasheet This document is subject to change without notice. 1 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com Table of Contents CMP40x0 WiFi/Bluetooth Modules Table of Contents ................................................................................................................................ 2 TRANSCEIVER IC .................................................................................................................................. 3 INTEGRATED FLASH ............................................................................................................................. 3 ABSOLUTE MAXIMUM RATINGS .......................................................................................................... 3 RECOMMENDED OPERATING CONDITIONS .......................................................................................... 3 POWER CONSUMPTION ...................................................................................................................... 4 Wi-Fi 2.4 GHz Band RF Receiver Specifications ..................................................................................... 5 Wi-Fi 2.4 GHz Band RF Transmitter Specifications ................................................................................ 6 Wi-Fi 5 GHz Band RF Receiver Specifications ........................................................................................ 7 Wi-Fi 5 GHz Band RF Transmitter Specifications ................................................................................... 8 Bluetooth 2.4 GHz Band RF Tx/Rx Specifications .................................................................................. 8 I/O PIN ASSIGNMENTS ........................................................................................................................ 9 MODULE PINOUT ...............................................................................................................................10 MODULE DIMENSIONS .......................................................................................................................10 MODULE LAND FOOTPRINT ................................................................................................................10 AGENCY CERTIFICATIONS for CMP40x0 ...............................................................................................13 SHIPMENT, HANDLING AND STORAGE ................................................................................................18 QUALITY ............................................................................................................................................18 ORDERABLE PART NUMBERS ..............................................................................................................19 REFERENCES .......................................................................................................................................19 REVISION HISTORY .............................................................................................................................19 DISCLAIMER .......................................................................................................................................20 This document is subject to change without notice. 2 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com CMP40x0 WiFi/Bluetooth Modules TRANSCEIVER IC The CMP40x0, utilizing the Realtek RTL8721x SoC, is a WiFi+Bluetooth combo device with dual-integrated MCU cores. This module supports WiFi- and Bluetooth communications while hosting the end-user application. The architecture is optimized for low-power consumption. Customers can select from several supported RTOS implementations and interface to a variety of peripherals or external MCUs. The CMP4010 uses the RTL8721C and supports 2.4 GHz WiFi. The CMP4020 uses the RTL8721D and supports 2.4 / 5 GHz WiFi. INTEGRATED FLASH The CMP40x0 incorporates additional SPI flash for storing program code and Over-The-Air code updates. The flash is managed by the core SoC SPI Flash Controller (SPIC) and is accessible by both MCU cores in the CMP40x0. CMP4010-1(C) 2 MB flash CMP4020-1(C) 2 MB flash CMP4020-2(C) 8 MB flash CMP4020-3(C) 16 MB flash ABSOLUTE MAXIMUM RATINGS Description Storage temperature range Power supply voltage (VDD) I/O supply voltage
* VDD = Terminal Supply Domain Min
-40 3.0 0.99 Max 125 3.6 3.6 Unit C V V RECOMMENDED OPERATING CONDITIONS Description Min Typ Max Unit Operating temperature range Power supply voltage (VDD)
-40 3.0
85 3.6 C V This document is subject to change without notice. 3 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com CMP40x0 WiFi/Bluetooth Modules POWER CONSUMPTION
(@25C unless otherwise specified) Operation Mode Scenario Min Typical Max Unit Deep Sleep Sleep Active WoWLAN Beacon WoWLAN DTIM=1 RTC Timer; 1 kB RAM retention KM4 Power Gate; KM0 Clock Gate All RAM retained; WiFi retained HT20 MCS0~7 Normal Mode KM4 Active Mode Rx Idle HT20 MCS0~7 ULP Mode KM4 Active Mode Rx Idle HT20 MCS0~7 ULP Mode KM4 Active Mode UDP Rx @ 8 Mbps Rx Beacon Normal Mode KM4 Sleep Mode Rx Beacon ULP Mode KM4 Sleep Mode KM4 Sleep Mode; SRAM Retained WiFi Retained Transmit Mode MCS7/HT20 18 dBm Tx MCS7/HT40 18 dBm (2.4 GHz) / 17 dBm (5 GHz) OFDM 54 Mbps 19 dBm (2.4 GHz) / 18 dBm (5 GHz) CCK 11 Mbps 18 dBm 7 30
7.5 40 52 35 39 28 23 8 50
700 750 800 Typical
(2.4 GHz) Typical
(5 GHz) 248 247 262 257 308 310 323 n/a uA uA mA mA uA Unit mA mA mA mA Bluetooth Operation Mode TX KM4 and M0 ON RX KM4 and M0 ON ADV KM4 and M0 ON Connection Condition Typical Units 4.5 dBm TX Central Mode Peripheral Mode Central Mode 100 56.1 56.2 56.3 mA mA mA mA This document is subject to change without notice. 4 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com CMP40x0 WiFi/Bluetooth Modules Wi-Fi 2.4 GHz Band RF Receiver Specifications
(@25C unless otherwise specified) Parameter Description Frequency Range Center Channel Frequency RX Sensitivity RX Sensitivity RX Sensitivity BW = 20 MHz Mixed Mode 800 ns Guard Interval Non-STBC RX Sensitivity BW = 40 MHz Mixed Mode 800 ns Guard Interval Non-STBC Maximum Receive Level 1 Mbps CCK 2 Mbps CCK 5.5 Mbps CCK 11 Mbps CCK BPSK rate 1/2, 6 Mbps OFDM BPSK rate 3/4, 9 Mbps OFDM QPSK rate 1/2, 12 Mbps OFDM QPSK rate 3/4, 18 Mbps OFDM 16QAM rate 1/2, 24 Mbps OFDM 16QAM rate 3/4, 36 Mbps OFDM 64QAM rate 1/2, 48 Mbps OFDM 64QAM rate 3/4, 54 Mbps OFDM MCS 0, BPSK rate 1/2 MCS 1, QPSK rate 1/2 MCS 2, QPSK rate 3/4 MCS 3, 16QAM rate 1/2 MCS 4, 16QAM rate 3/4 MCS 5, 64QAM rate 2/3 MCS 6, 64QAM rate 3/4 MCS 7, 64QAM rate 5/6 MCS 0, BPSK rate 1/2 MCS 1, QPSK rate 1/2 MCS 2, QPSK rate 3/4 MCS 3, 16QAM rate 1/2 MCS 4, 16QAM rate 3/4 MCS 5, 64QAM rate 2/3 MCS 6, 64QAM rate 3/4 MCS 7, 64QAM rate 5/6 6 Mbps OFDM 54 Mbps OFDM MCS 0 MCS 7 1 Mbps CCK 11 Mbps CCK Receive Adjacent Channel Rejection BPSK rate 1/2, 6 Mbps OFDM 64QAM rate 3/4, 54 Mbps OFDM HT20, MCS 0, BPSK rate 1/2 HT20, MCS 7, 64QAM rate 5/6 HT40, MCS 0, BPSK rate 1/2 HT40, MCS 7, 64QAM rate 5/6 Unit MHz dBm dBm dBm dBm dBm dBm Min 2412
-99.1
-97
-94.5
-91.5
-96
-94.5
-93
-91
-87
-84
-79.5
-78.1
-95.5
-92.2
-90
-86.5
-83.2
-78.5
-77
-75.7
-93
-89.5
-87
-83.5
-80
-75.5
-74.5
-73
42 39 39 20 39 19 27 9 Typ
-98.6
-95.9
-94.2
-91.1
-95.4
-94.3
-92.9
-90.4
-86.8
-83.8
-79.2
-77.8
-95.1
-92
-89.4
-85.8
-82.9
-78.4
-76.7
-75.4
-92.5
-88.7
-86.5
-83.3
-79.9
-75.4
-74
-72.5 0 0 0 0 43 41 40 22 39 20 29 10 Max 2484
-97.5
-95.5
-93.5
-90.6
-94.3
-93.9
-92.5
-90
-86.4
-83.4
-78.9
-77
-94.1
-91.7
-89
-84
-82.5
-78
-76.4
-75
-92.2
-87
-86.4
-83
-79
-75
-73.9
-72.3
44 42 41 24 40 21 32 11 This document is subject to change without notice. 5 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com CMP40x0 WiFi/Bluetooth Modules Wi-Fi 2.4 GHz Band RF Transmitter Specifications
(@25C unless otherwise specified) Parameter Description Frequency Range Center Channel Frequency Min 2412 Output power with spectral mask and EVM compliance TX EVM 1 Mbps CCK 11 Mbps CCK BPSK rate 1/2, 6 Mbps OFDM 64QAM rate 3/4, 54 Mbps OFDM HT20, MCS 0, BPSK rate 1/2 HT20, MCS 7, 64QAM rate 5/6 HT40, MCS 0, BPSK rate 1/2 HT40, MCS 7, 64QAM rate 5/6 BPSK rate 1/2, 6 Mbps OFDM 64QAM rate 3/4, 54 Mbps OFDM HT20, MCS 0, BPSK rate 1/2 HT20, MCS 7, 64QAM rate 5/6 HT40, MCS 0, BPSK rate 1/2 HT40, MCS 7, 64QAM rate 5/6 Output Power Variation After Power Trim Carrier Suppression Harmonic Output Power 1st Harmonic 2nd Harmonic 3rd Harmonic
-1.5
Typ
18 18 17 17 16 16 16 16
Max 2484 Unit MHz
-5
-25
-5
-28
-5
-28 1.5
-30 dBm dBm dBm dBm
-23-
-15
-21.9
-14 This document is subject to change without notice. 6 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com CMP40x0 WiFi/Bluetooth Modules Wi-Fi 5 GHz Band RF Receiver Specifications
(@25C unless otherwise specified) Parameter Description Frequency Range Center Channel Frequency RX Sensitivity RX Sensitivity BW = 20 MHz Mixed Mode 800 ns Guard Interval Non-STBC RX Sensitivity BW = 40 MHz Mixed Mode 800 ns Guard Interval Non-STBC BPSK rate 1/2, 6 Mbps OFDM BPSK rate 3/4, 9 Mbps OFDM QPSK rate 1/2, 12 Mbps OFDM QPSK rate 3/4, 18 Mbps OFDM 16QAM rate 1/2, 24 Mbps OFDM 16QAM rate 3/4, 36 Mbps OFDM 64QAM rate 1/2, 48 Mbps OFDM 64QAM rate 3/4, 54 Mbps OFDM MCS 0, BPSK rate 1/2 MCS 1, QPSK rate 1/2 MCS 2, QPSK rate 3/4 MCS 3, 16QAM rate 1/2 MCS 4, 16QAM rate 3/4 MCS 5, 64QAM rate 2/3 MCS 6, 64QAM rate 3/4 MCS 7, 64QAM rate 5/6 MCS 0, BPSK rate 1/2 MCS 1, QPSK rate 1/2 MCS 2, QPSK rate 3/4 MCS 3, 16QAM rate 1/2 MCS 4, 16QAM rate 3/4 MCS 5, 64QAM rate 2/3 MCS 6, 64QAM rate 3/4 MCS 7, 64QAM rate 5/6 6 Mbps OFDM 54 Mbps OFDM MCS 0 MCS 7 Maximum Receive Level BPSK rate 1/2, 6 Mbps OFDM 64QAM rate 3/4, 54 Mbps OFDM HT20, MCS 0, BPSK rate 1/2 HT20, MCS 7, 64QAM rate 5/6 HT40, MCS 0, BPSK rate 1/2 HT40, MCS 7, 64QAM rate 5/6 Unit MHz dBm dBm dBm dBm Min 5180
-94.5
-93.5
-92
-90
-86.5
-83.5
-79
-77.5
-94
-91.5
-89
-86
-82.6
-78
-76.5
-74.8
-91.5
-88.5
-85.5
-82.5
-79
-74.5
-73.5
-72
19 10 19 7 29 11 Typ
-93.6
-92.8
-91.5
-89.1
-85.6
-82.8
-78.3
-76.7
-93.3
-90.7
-88.2
-85
-81.9
-77.1
-75.4
-73.7
-90.6
-87.8
-85.2
-82.1
-78.7
-74
-72.8
-71.3 0 0 0 0 21 11 19 7 30 13 Max 5825
-92
-91
-90.5
-88
-84.5
-82
-77.5
-76
-91.5
-89.5
-87
-84
-80.5
-76
-74
-72.5
-88.5
-86.5
-83.5
-81
-78
-73
-72
-70.5
23 12 20 9 31 14 This document is subject to change without notice. 7 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com CMP40x0 WiFi/Bluetooth Modules Wi-Fi 5 GHz Band RF Transmitter Specifications
(@25C unless otherwise specified) Parameter Description Frequency Range Center Channel Frequency Min 5180 BPSK rate 1/2, 6 Mbps OFDM 64QAM rate 3/4, 54 Mbps OFDM HT20, MCS 0, BPSK rate 1/2 HT20, MCS 7, 64QAM rate 5/6 HT40, MCS 0, BPSK rate 1/2 HT40, MCS 7, 64QAM rate 5/6 BPSK rate 1/2, 6 Mbps OFDM 64QAM rate 3/4, 54 Mbps OFDM HT20, MCS 0, BPSK rate 1/2 HT20, MCS 7, 64QAM rate 5/6 HT40, MCS 0, BPSK rate 1/2 HT40, MCS 7, 64QAM rate 5/6 TX EVM Output Power Variation After Power Trim Carrier Suppression Bluetooth 2.4 GHz Band RF Tx/Rx Specifications
(@25C unless otherwise specified) Parameter Frequency Range TX Power RX Sensitivity (LE 1M PHY) RX Sensitivity (LE 2M PHY) Min 2402
-100.9
-96.8
-1.5
Typ
4.5
Typ
17 16 16 15 16 15
Max 2480
Max 5825 Unit MHz
-5
-25
-5
-28
-5
-28 1.5
-30 dBm dBm dBm Unit MHz dBm dBm dBm This document is subject to change without notice. 8 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com I/O PIN ASSIGNMENTS Refer to the RTL8721 datasheet for pin functionality details. CMP40x0 WiFi/Bluetooth Modules Module Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 Notes Adding a 12K pull down resistor enables HSUSB Either HSDP or GPIO PA26 depending on 12K pull down present or not Either HSDP or GPIO PA26 depending on 12K pull down present or not Pin Name PA27 PA30 RREF/PA28 HSDP/PA26 HSDM/PA25 PB1 PB2 PB3 PB4 PB5 PB6 PB7 VCC GND FLASH SPI Data In Pin not available as GPIO: Dedicated to Flash NC FLASH_SPI_CS FLASH_SPI_Data Out Pin isolated from Flash CLK Pin not available as GPIO: Dedicated to FLASH Pin not available as GPIO: Dedicated to FLASH PB22 PB23 PB26 PB29 PB31 PA0 GND PA4 PA2 CHIP_ENABLE UART_LOG_TXD / PA7 This Pin pulled low with Reset applied placed device in Download Mode UART_LOG_RXD / PA8 PA19 PA18 PA17 PA16 PA15 PA14 PA12 PA13 GND This document is subject to change without notice. 9 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com MODULE PINOUT CMP40x0 WiFi/Bluetooth Modules MODULE DIMENSIONS 1.036 x 0.656 x 0.142 in (16.7 x 26.3 x 3.6 mm) MODULE LAND FOOTPRINT Dimensions in inches. EVALUATION BOARDS This document is subject to change without notice. 10 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com CMP40x0 WiFi/Bluetooth Modules PROCESSING Recommended Reflow Profile Parameter Values Ramp Up Rate (from Tsoakmax to Tpeak) 3/sec max Minimum Soak Temperature Maximum Soak Temperature Soak Time TLiquidus Time above TL Tpeak Time within 5 of Tpeak Time from 25 to Tpeak 150C 200C 60-120 sec 217C 60-150 sec 250C 20-30 sec 8 min max Ramp Down Rate 6C/sec max Pb-Free Solder Paste Use of No Clean soldering paste is strongly recommended, as it does not require cleaning after the soldering process. Note: The quality of solder joints on the castellations ("half vias") where they contact the host board should meet the appropriate IPC Specification. See the Castellated Terminations Section in the latest IPC-A-610 Acceptability of Electronic Assemblies document. Cleaning In general, cleaning the populated module is strongly discouraged. Residuals under the module cannot be easily removed with any cleaning process. Cleaning with water can lead to capillary effects where water is absorbed into the gap between the host board and the module. The combination of soldering flux residuals and encapsulated water could lead to short circuits between neighboring pads. Water could also damage any stickers or labels. Cleaning with alcohol or a similar organic solvent will housings, which is not accessible for post-washing inspection. The solvent could also damage any stickers or labels. Ultrasonic cleaning could damage the module permanently. flood soldering flux residuals likely into the two The best approach is to consider using a No Clean solder paste and eliminate the post-soldering cleaning step. Optical Inspection After soldering the module to the host board, consider optical inspection to check the following:
Proper alignment and centering of the module over the pads Proper solder joints on all pads Excessive solder or contacts to neighboring pads or vias This document is subject to change without notice. 11 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com CMP40x0 WiFi/Bluetooth Modules Repeating Reflow Soldering Only a single reflow soldering process is encouraged for host boards. Wave Soldering If a wave soldering process is required on the host boards due to the presence of leaded components, only a single wave soldering process is encouraged. Hand Soldering Hand soldering is possible. When using a soldering iron, follow IPC recommendations (reference document IPC-7711). Rework The CMP4010 can be unsoldered from the host board. Use of a hot air rework tool should be programmable and the solder joint and module should not exceed the maximum peak reflow temperature of 250C. Caution If temperature ramps exceed the reflow temperature profile, module and component damage may occur due to thermal shock. Avoid overheating. Warning Never attempt a rework on the module itself (i.e., replacing individual components); such actions will terminate warranty coverage. Additional Grounding Attempts to improve the module or the system grounding by soldering braids, wires or cables onto the module RF shield cover is done at the customer's own risk. The ground pins at the module perimeter should be sufficient for optimum immunity to external RF interference. This document is subject to change without notice. 12 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com CMP40x0 WiFi/Bluetooth Modules AGENCY CERTIFICATIONS for CMP40x0 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module:
KDB 996369 D03 OEM Manual v01 rule sections:
2.2 List of applicable FCC rules This module has been tested for compliance to FCC Part 15 2.3 Summarize the specific operational use conditions The module is tested for standalone mobile RF exposure use condition. Any other usage conditions such as co-
location with other transmitter(s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification. 2.4 Limited module procedures Not applicable. 2.5 Trace antenna designs Not applicable. 2.6 RF exposure considerations This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules. 2.7 Antennas (CMP4020 only) This document is subject to change without notice. 13 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com CMP40x0 WiFi/Bluetooth Modules The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. The antenna must be installed such that 20 cm can be maintained between the antenna and users. Antenna NO. RF Chain NO. Brand Model Antenna Net Gain(dBi) Frequency range Antenna Type Connector Type
*Cable Length 1 2 0 MAG.LAY ERS MSA-4008-25GC1-
A2 2.98 2.4~2.5GHz PIFA ipex(MHF) 150mm 0 CEL 0027-02-07-00-001 2.1 2.4~2.5GHz PIFA none none 5.16 5.15~5.85G Hz 3.5 5.15~5.85G Hz 2.8 Label and compliance information The final end product must be labeled in a visible area with the following:
CMP4010 - Contains FCC ID: W7Z-WB242102. CMP4020 - Contains FCC ID: W7Z-WB220501. The grantee's FCC ID can be used only when all FCC compliance requirements are met. 2.9 Information on test modes and additional testing requirements This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) or portable use will require a separate class II permissive change re-evaluation or new certification. 2.10 Additional testing, Part 15 Subpart B disclaimer This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B
(unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-
location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. OEM/Host manufacturer responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules. This module must not be incorporated into any other device or system without retesting for compliance as multi-radio and combined equipment This document is subject to change without notice. 14 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com CMP40x0 WiFi/Bluetooth Modules Industry Canada statement:
This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with greater than 20cm between the radiator & your body. Dclaration radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis plus de 20 cm entre le radiateur et votre corps. d'exposition aux This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 1 condition ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:
Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed and operated with greater than 20cm between the antenna and users. The final end product must be labeled in a visible area with the following:
CMP4010 - Contains IC: 8254A-WB242102. CMP4020 - Contains IC: 8254A-WB220501. Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un appareil o lantenne peut tre installe et utilise plus de 20 cm entre lantenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante:
"Contient des IC: 8254A-WB242102 (CMP4010) 8254A-WB220501 (CMP4020)". This document is subject to change without notice. 15 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com CMP40x0 WiFi/Bluetooth Modules Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. ce module RF dans l'utilisateur du produit le manuel de final qui intgre Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-
channel mobile satellite systems;
(ii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate;
(iv) where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated. Avertissement:
Le guide dutilisation des dispositifs pour rseaux locaux doit inclure des instructions prcises sur les restrictions susmentionnes, notamment :
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
(ii) pour les dispositifs munis dantennes amovibles, le gain maximal dantenne permis pour les dispositifs utilisant les bandes de 5 250 5 350 MHz et de 5 470 5 725 MHz doit tre conforme la limite de la p.i.r.e;
(iii) pour les dispositifs munis dantennes amovibles, le gain maximal dantenne permis (pour les dispositifs utilisant la bande de 5 725 5 850 MHz) doit tre conforme la limite de la p.i.r.e. spcifie, selon le cas;
(iv) lorsquil y a lieu, les types dantennes (sil y en a plusieurs), les numros de modle de lantenne et les pires angles dinclinaison ncessaires pour rester conforme lexigence de la p.i.r.e. applicable au masque dlvation, nonce la section 6.2.2.3, doivent tre clairement indiqus This document is subject to change without notice. 16 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com CMP40x0 WiFi/Bluetooth Modules DETACHABLE ANTENNA USAGE (CMP4020) This radio transmitter [IC: 8254A-WB220501] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Le prsent metteur radio [IC: 8254A-WB220501] a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'metteur. Antenna NO. RF Chain NO. Brand Model Antenna Net Gain(dBi) Frequency range Antenn a Type Connect or Type 1 2 0 0 MAG.LAY ERS CEL MSA-4008-
25GC1-A2 0027-02-07-
00-001 2.98 5.16 2.1 3.5 2.4~2.5GHz 5.15~5.85GHz 2.4~2.5GHz 5.15~5.85GHz PIFA ipex(MH F) PIFA none Cab le Len gth 150 mm non e Impedance
() 50 50 50 50 European Standards Testing Completed Contact CEL for details and test reports. EN 62311 EN 301893 EN 300328-WLAN EN 300328-BT This document is subject to change without notice. 17 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com CMP40x0 WiFi/Bluetooth Modules SHIPMENT, HANDLING AND STORAGE Tape and Reel The CMP4010 modules are delivered in tape and reel. Each reel contains 600 modules. Handling The CMP4010 modules are designed and packaged to be processed in an automated assembly line. Warning The CMP4010 modules contain highly sensitive electronic circuitry. Handling without proper ESD protection may destroy or damage the module permanently. Warning The CMP4010 modules are moisture-sensitive devices. Appropriate handling instructions and precautions are summarized in J-
STD-033. Read carefully to prevent permanent damage due to moisture intake. Moisture Sensitivity Level (MSL) MSL 3, per J-STD-033 Storage Storage/shelf life in sealed bags is 12 months at <40C and <90% relative humidity. QUALITY CEL Modules offer the highest quality at competitive prices. Our modules are manufactured in compliance with the IPC-A-610 specification, Class II. Our modules go through JESD22 qualification processes which includes high temperature operating life tests, mechanical shock, temperature cycling, humidity and reflow testing. CEL conducts RF and DC factory testing on 100% of all production parts. CEL builds the quality into our products, giving our customers confidence when integrating our products into their systems. This document is subject to change without notice. 18 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com CMP40x0 WiFi/Bluetooth Modules ORDERABLE PART NUMBERS Orderable Part Number Description CMP4010-1-R RTL8721C IC, Wi-Fi + BT combo, 2 MB, PCB antenna CMP4010-1C-R RTL8721C IC, Wi-Fi + BT combo, 2 MB, u.Fl connector CMP4010-1-EVB Evaluation Board, RTL8721C IC, Wi-Fi + BT combo, 2 MB Min/Mult 600/600 600/600 1/1 CMP4020-1-R RTL8721D IC, Dual Band Wi-Fi + BT combo, 2 MB, PCB antenna 600/600 CMP4020-1C-R RTL8721D IC, Dual Band Wi-Fi + BT combo, 2 MB, u.Fl connector 600/600 CMP4020-1-EVB Evaluation Board, RTL8721D IC, Dual Band Wi-Fi + BT combo, 2 MB 1/1 CMP4020-2-R RTL8721D IC, Dual Band Wi-Fi + BT combo, 8 MB, PCB antenna 600/600 CMP4020-2C-R RTL8721D IC, Dual Band Wi-Fi + BT combo, 8 MB, u.Fl connector 600/600 CMP4020-3-R RTL8721D IC, Dual Band Wi-Fi + BT combo, 16 MB, PCB antenna 600/600 CMP4020-3C-R RTL8721D IC, Dual Band Wi-Fi + BT combo, 16 MB, u.Fl connector 600/600 NOTE: THE '-R' IN THE ORDERABLE PARTNUMBER SHOULD BE REPLACED WITH -B FOR BULK QTYS. REFERENCES Health Canada Safety Code 6 REVISION HISTORY Reference Documents Revision Changes to Current Version 0027-00-07-00-000
(Issue A) July 17, 2020 0027-00-07-00-000
(Issue B) Sept 25, 2020 0027-00-07-00-000
(Issue C) Oct 30, 2020 Initial Preliminary Data Sheet Add Reference Code Available section. Add BLE Mesh capability. Update operational temperature range 0027-00-07-00-000
(Issue D) Apr 26, 2021 Add FCC/IC certification information. Update Orderable PN Table 0027-00-07-00-000
(Issue E) June 1, 2021 0027-00-07-00-000
(ISSUE F) May 23, 2022 0027-00-07-00-000
(ISSUE G) JUNE, 2022 0027-00-07-00-000
(ISSUE H) JAN, 2023 0027-00-07-00-000
(ISSUE J) FEB, 2023 Change BLE Tx power. Correct PN in references to core SoC. Convert to CMP40x0; Add 5 GHz data for CMP4020 Clarify SPI FLASH Pin Assignments; Add Orderable PNs for higher flash densities Add certification details for CMP4020 Add CE test data list. Download Link Page(s) N/A 1 4 12 15 7
10 17 This document is subject to change without notice. 19 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com CMP40x0 WiFi/Bluetooth Modules DISCLAIMER The information in this document is current as of the published date. The information is subject to change without notice. For actual design-in, refer to the latest publications of CEL Data Sheets or Data Books, etc., for the most up-to-date specifications of CEL products. Not all products and/or types are available in every country. Please check with a CEL sales representative for availability and additional information. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of CEL. CEL assumes no responsibility for any errors that may appear in this document. CEL does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of CEL products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of CEL or others. Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customers equipment shall be done under the full responsibility of the customer. CEL assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. While CEL endeavors to enhance the quality, reliability and safety of CEL products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in CEL products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-
containment and anti-failure features. FOR MORE INFORMATION For more information about CEL wireless products and solutions, visit our website at www.cel.com/. TECHNICAL ASSISTANCE For Technical Assistance, please contact us at wirelessmodules@cel.com This document is subject to change without notice. 20 Document No.: 0027-00-07-00-000 Issue J California Eastern Laboratories wirelessmodules@cel.com / www.cel.com