CM-TX-99 Lazerpoint RF Transmitter Installation Instructions Package Contents 1 CM-TX-99 Lazerpoint RF Transmitter Description CAMDEN DOOR CONTROLS CM-TX-99 RF Transmitter is designed for industrial and commercial applications, where wireless operation is required. The transmitter is a plug-in board designed to interface to the CM-120i/W Keypads and the CM-325 Touchless Switch. Application Camden CM-TX-99 RF Transmitter is ideal for applications where running additional cable is expensive or impractical. Installation CM-TX-99 is installed by aligning the pins with the socket on the CM-120i/W Keypad or CM-325 Touchless switch and plugging it in. Pairing CM-TX-99 is easily paired with Camden CM-RX-91 and CM-
RX-92 Lazerpoint Receivers. Pairing the CM-120i/W Keypad To learn the transmitter into the receiver, press the PB1 button
(on the CM-RX-91/92) using a small blunt object, such as a small blade screwdriver or similar. Within 10 seconds, enter a valid user code on the CM-120i/W Keypad connected to a CM-TX-99 transmitter. The Green LED Array will flash once to confirm enrollment. Pairing the CM-325 Touchless Switch To learn the transmitter into the receiver, press the PB1 button
(on the CM-RX-91/92) using a small blunt object, such as a small blade screwdriver or similar. Within 10 seconds, wave your hand in front of the CM-325 connected to a CM-TX-99 transmitter to activate the switch. The Green LED Array will flash once to confirm enrolment. If you wait longer than the 10-second period, the receiver will time out of Learn Mode and revert back to standby. The LED will then flash to indicate the number of transmitters learned into the receiver. 1
(40mm) 9/16
(15mm) CAMDEN LAZERPOINT 1/4
(6mm) 5/16
(8mm) Page 1 of 2 CM-TX-99 Lazerpoint RF Transmitter Installation Instructions IC & FCC INFORMATION FOR USERS IC: 8725A-TX99 This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1) lappareil ne doit pas produire de brouillage;
2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. FCC ID: 2AHAB-TX99 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications made to this equipment not expressly approved by Camden Door Control could void the users authority to operate the equipment. OEM Labeling Requirements WARNING: The Original Equipment Manufacturer (OEM) must ensure that FCC labeling requirements are met. This includes a clearly visible label on the outside of the final product enclosure that displays the contents shown in the figure below. Required FCC Label for OEM products containing the CM-TX99 Module. Contains FCC ID: 2AHAB-TX99 & IC: 8725A-TX99 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interferences that may cause undesired operation. IMPORTANT: OEMs must test final product to comply with unintentional radiators (FCC section 15.107 & 15.109) before declaring compliance of their final product to Part 15 of the FCC Rules. Questions? Call us toll-free at 1-877-226-3369 Push Buttons Key Pads Strikes Magnetic Locks Key Switches Relays & Timers Access Control 5502 Timberlea Blvd., Mississauga, ON Canada L4W 2T7 www.camdencontrols.com Toll Free: 1.877.226.3369 File: CM-TX-99 Lazerpoint RF Transmitter-Manual-Eng .indd-Rev3 October 26, 2016 Part No.: 40-82B0148 Page 2 of 2