802.11g Wireless USB 2.0 Adapter CAMEO/WLG-1502 Users Guide Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
to which the receiver is connected.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual. Consult the dealer or an experienced radio/TV technician for help. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. SAR compliance has been established in typical laptop computer(s) with USB slot, and product could be used in typical laptop computer with USB slot. Other application like handheld PC or similar device has not been verified and may not compliance with related RF exposure rule and such use shall be prohibited. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. Europe EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:
EN 60 950-1: 2001 +A11: 2004 Safety of Information Technology Equipment EN 50361 (2001) Basic standard for the measurement of specific absorption rate related to human exposure to electromagnetic fields from mobile phones (300 MHz-3 GHz) EN 50392:2004 Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic fields (0 Hz - 300 GHz) EN 300 328 V1.6.1 (2004-11) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive EN 301 489-1 V1.6.1: (2005-09) Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements EN 301 489-17 V1.2.1 (2002-08) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. 0560
[Czech]
esky
[Jmno vrobce] tmto prohlauje, e tento [typ zazen] je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 1999/5/ES. Dansk
[Danish]
Deutsch
[German]
Undertegnede typebetegnelse] overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF.
[fabrikantens navn] erklrer herved, at flgende udstyr
[udstyrets Hiermit erklrt [Name des Herstellers], dass sich das Gert [Gertetyp] in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti
[Estonian]
Kesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tp = type of equipment] vastavust direktiivi 1999/5/E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Espaol
[Spanish]
Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
[name of manufacturer] [type of equipment]
[Greek]
1999/5/. Franais
[French]
Par la prsente [nom du fabricant] dclare que l'appareil [type d'appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano
[Italian]
Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski
[Latvian]
Ar o [name of manufacturer / izgatavotja nosaukums] deklar, ka [type of equipment /
iekrtas tips] atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. Lietuvi
[Lithuanian]
iuo [manufacturer name] deklaruoja, kad is [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlands
[Dutch]
Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti
[Maltese]
Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-
tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar
[Hungarian]
Alulrott, [gyrt neve] nyilatkozom, hogy a [... tpus] megfelel a vonatkoz alapvet kvetelmnyeknek s az 1999/5/EC irnyelv egyb elrsainak.
[Polish]
Polski Niniejszym [nazwa producenta] owiadcza, e [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostaymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Portugus
[Portuguese]
[Nome do fabricante] declara que este [tipo de equipamento] est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE. Slovensko
[Slovenian]
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloili direktive 1999/5/ES. Slovensky
[Slovak]
[Meno vrobcu] tmto vyhlasuje, e [typ zariadenia] spa zkladn poiadavky a vetky prslun ustanovenia Smernice 1999/5/ES. Suomi
[Finnish]
[Valmistaja = manufacturer] vakuuttaa tten ett [type of equipment = laitteen tyyppimerkint]
tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Svenska
[Swedish]
Hrmed intygar [fretag] att denna [utrustningstyp] str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG. TABLE OF CONTENT Introduction............................................................................................................................................................................................... 1 Overview of this Users Guide.............................................................................................................................................................. 1 Unpacking and Setup ................................................................................................................................................................................ 2 Unpacking............................................................................................................................................................................................. 2 Setup ..................................................................................................................................................................................................... 2 Hardware Installation................................................................................................................................................................................ 3 LED Indicator ....................................................................................................................................................................................... 3 Check the installation............................................................................................................................................................................ 3 Software Installation ................................................................................................................................................................................. 4 Utility and Driver Installation ............................................................................................................................................................... 4 Wireless utility setting .............................................................................................................................................................................. 7 Link Info ............................................................................................................................................................................................... 7 Configuration ........................................................................................................................................................................................ 8 Advanced .............................................................................................................................................................................................. 9 Site Survey.......................................................................................................................................................................................... 12 Technical Specifications ......................................................................................................................................................................... 14 i INTRODUCTION Congratulations on your purchase of this 802.11g Wireless USB 2.0 Adapter. This manual helps to get familiar with the 802.11g Wireless USB 2.0 Adapter. This manual contains detailed instructions in operation of this product. Please keep this manual for future reference. With a Wireless LAN (IEEE 802.11g) USB 2.0 Adapter, a desktop or laptop computer can communicate with another computer in a wireless way. Easy-to-use utilities are bundled with Wireless USB Adapter for configuration, monitoring, and diagnosis purposes. The 802.11g Wireless USB 2.0 Adapter can wirelessly transmit and receive data, minimizing the need for wired connections, at a speed of up to fifty-four megabit per second. The 802.11g Wireless USB 2.0 Adapter provides users with an access to real-time information anywhere in their organization. The mobility provides productivity and service, which are not available under wired networks. The 802.11g Wireless USB 2.0 Adapter configuration is easy to change from peer-to-peer networks, suitable for a small number of users, to full infrastructure networks of thousands of users that allow roaming around a broad area. Overview of this Users Guide Introduction. Describes the 802.11g Wireless USB 2.0 Adapter and its features. Unpacking and Setup. Helps you get started with the basic installation of the 802.11g Wireless USB 2.0 Adapter. Hardware Installation. Describes the LED indicators of the Adapter. Software Installation. Tells how to setup the driver and the utility setting. Technical Specifications. Lists the technical specifications of the 802.11g Wireless USB 2.0 Adapter. 1 UNPACKING AND SETUP This chapter provides unpacking and setup information for the 802.11g Wireless USB 2.0 Adapter. Unpacking Open the box of the 802.11g Wireless USB 2.0 Adapter and carefully unpack it. The box should contain the following items:
One 802.11g Wireless USB 2.0 Adapter
One Driver & Utility CD-ROM If any item is found missing or damaged, please contact your local reseller for replacement. Setup The setup of the 802.11g Wireless USB 2.0 Adapter can be performed using the following steps:
Visually inspect the USB connector and make sure that it is fully plugged in to the systems USB port.
Make sure that there is a well environment that there is no much intrusion to have a better connection. 2 HARDWARE INSTALLATION LED Indicator LINK The LINK LED lights green when the 802.11g Wireless USB 2.0 Adapter is connected to a network successfully. Otherwise the LINK indicator blinks green while the 802.11g Wireless USB 2.0 Adapter is access the wireless network. Check the installation The LED of the 802.11g Wireless USB 2.0 Adapter is clearly visible and the status of the network link can be seen instantly:
1. When connected to the USB port and the driver were installed, the LNK LED will start blinking, and it means that the device is starting to scan an 802.11g wireless device near the 802.11g Wireless USB 2.0 Adapter. 2. While the 802.11g Wireless USB 2.0 Adapter linked up to the Access Point or to other Wireless LAN station, the LINK LED will always light up. 3 SOFTWARE INSTALLATION This section will lead you to install the driver and utility of the 802.11g Wireless USB 2.0 Adapter. Before insert the USB Dongle into USB port of your computer, please install the Utility Program first. Make sure that the 802.11g Wireless USB 2.0 Adapter is NOT inserted into the USB slot. Utility and Driver Installation Insert the 802.11g Wireless LAN USB 2.0 Adapter Driver & Utility CD-ROM into computers CD-ROM Drive and it will automatically run a setup menu and install the driver and the utility. In some specific setting on Windows system, you may need to proceed the software manually, go to your Windows Start menu and choose Run, type D:\Setup\Setup.exe in the dialog box (D:\ will depend on where your CD-ROM drive is located). Note: (D:\ will depends on where the CD-ROM drive is located and <Windows OS> will depend on the Windows Operating System you are using). 1. Click Install to start the Utility and driver installation. 4 2. The Install Shield Wizard screen will appear. Click Next to continue. 3. Click Finish to finish the installation. 5 4. Plug-in your 802.11g Wireless USB 2.0 Adapter into your computers USB port. 5. You will see the icon on the Windows task bar when you finish the utility installation and plugged the 802.11g Wireless USB 2.0 Adapter. When the icon in the toolbar represents in green color, it is properly connected to the network and shown the linking quality. 6 WIRELESS UTILITY SETTING Windows XP users may use the built-in wireless utility as default. The following instructions are for Service Pack 2 users. If you are using Windows 2000/98/ME, you must use the Wireless Utility. With the Wireless utility, users can configure all the functions provided by the Wireless LAN Adapter Utility. Double-click the utility icon system tray. that appears in the The Wireless LAN Adapter Utility includes six tabs: Link Info, Configuration, Advanced, Site Survey and About. Link Info The Link Info screen shows you the status of the Wireless Adapter, it shows that where the device is connected to, the connect Status, the connecting Speed, the network Type, the Encryption type, the SSID and the Signal Strength. 7 Configuration This is the page where you can change the basic settings of the 802.11g Wireless USB 2.0 Adapter with the minimum amount of effort to implement a secure wireless network environment. SSID: The SSID differentiates one Wireless LAN group name from another; so all access points and all devices attempting to connect to a specific Wireless LAN group name must use the same SSID. A device will not be permitted to join the BSS unless it can provide the unique SSID. Wireless Mode: If you want to connect with an Access Point/WLAN Router, please set to Infrastructure mode. If you have more stations and just want to set them as local network, please set the mode to Ad-hoc mode. Channel: It shows auto that used for Infrastructure Wireless LAN network. The channel number can be set only under the Ad-Hoc operation mode. In Ad-Hoc mode stations, each station must have the same channel number and SSID. In Infrastructure mode, the Wireless USB Adapter will automatically detect the channel number of the Access Point. Power Mode: There are 3 modes to choose:
Continuous Access Mode (default): The USB Dongle is constantly operating with full power and it consumes the most power. Maximum Power Save: The USB Dongle consumes the least power and only operates when there is wireless network activity. Power Save: The USB Dongle consumes the moderate level of power. 8 Preamble: Select Long or Short/Long (auto) Preamble type. Preamble is a sequence of bits transmitted at 1Mbps that allows the PHY circuitry to reach steady-state demodulation and synchronization of bit clock and frame start. Two different preambles and headers are defined: the mandatory supported Long Preamble and header, which interoperates with the 1 Mbit/s and 2 Mbit/s DSSS specification (as described in IEEE Std. 802.11), and an optional Short Preamble and header (as described in IEEE Std. 802.11b). At the receiver, the Preamble and header are processed to aid in demodulation and delivery of the PSDU. The Short Preamble and header may be used to minimize overhead and, thus, maximize the network data throughput. However, the Short Preamble is supported only from the IEEE 802.11b (High-Rate) standard and not from the original IEEE 802.11. That means that stations using Short-Preamble cannot communicate with stations implementing the original version of the protocol. Support Band: There are two bands available for selection; 11B and 11G. Advanced The Advanced settings help you to control the Wireless Adapter to adjust with wireless devices in certain environment. Auth. Mode: Eight options are available: Disable, Auto, Open System, Shared Key, WPA/WPA2, and WPA-PSK/WPA2-PSK. Select Auto, Disable for other authentication feature. If one of the two options is selected, it is required to select the Encryption mode from the next dropping list. 9 Shared Key/Open System Network Key: Choose the encryption way, either in HEX or ASCII formats, and enter the password in the blank space. Key Length, Key Format and WEP Key: If you select 64bit in Hex format, you must type 10 values in the following range (0~F, hexadecimal), or 64bit in ASCII format, you must type 5 values in the following range (0~9, A~Z and a~z Alphanumeric). If you select 128bit in Hex format, you must type 26 values (0~F, hexadecimal), or 128bit in ASCII format, you must type 13 values in the following range (0~9, A~Z and a~z Alphanumeric). WPA-PSK / WPA2-PSK Click the Configuration button than enter a Passphrase in the Define WPA PSK dialog box. This Passphrase must be the same on each computer that is connected to the wireless network. 10 WPA / WPA2 WPA2 (Wi-Fi Protected Access 2) is the second generation of WPA; providing enterprise and consumer Wi-Fi user with a high level of assurance that only authorized user can access their wireless networks. WPA2 is based on the final IEEE802.11i amendment to the 802.11 standard and is eligible for FIPS 140-2 compliant. WPA2 the Certificate button. The below window is pop up. Then, please select the certificate that user wants to use and enter the server name and login name. is select, configuration Please click is enabled. 11 Site Survey Available Network The screen shows all the Wireless LAN devices around your Wireless LAN USB Adapter. The information of the wireless devices includes the SSID, MAC Address, Channels, Signal, the Security type and the Network mode. You can click the Refresh button to find the new wireless LAN devices, and double-click the device to choose the wireless station that you want to connect with. 12 Profile Add: Click Add to create a new profile, set the related values such as Profile name, SSID, Wireless Mode and Security settings than click Apply to save the profile. Edit: Click Edit to modify existing profile, modify the settings than click Apply to save the profile. Remove: Choose a profile name in the Available Profiles and click Remove to remove the existing profile. Connect: Choose a profile name in the Available Profiles and click Connect to activate the existing profile. About The About section shows you the 802.11g Wireless USB 2.0 Adapter information, it shows MAC address, Utility Version, Driver Version, Regulatory Domain. 13 TECHNICAL SPECIFICATIONS General Standards IEEE 802.11g, USB 2.0, 1.1, 1.0 Radio Technology IEEE 802.11b -- DSSS IEEE 802.11g -- OFDM Data Transfer Rate 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54Mbps (auto sense) Receiver Sensitivity 54Mbps: Typical -68dBm @ 10% PER (Packet Error Rate) 11Mbps: Typical -83dBm @ 8% PER (Packet Error Rate) Frequency Range 2412 MHz 2462 MHz (FCC/NCC) 2412 MHz 2472 MHz (ETSI) 2400 MHz 2497 MHz (Japan) Modulation Schemes BPSK/QPSK/CCK/OFDM Channels 1 ~ 11 channels (FCC/NCC) 1 ~ 13 channels (ETSI) 1 ~ 14 channels (Japan) Media Access Protocol CSMA/CA with ACK Security 64/128bits WEP, WPA, WPA2, WPA-PSK, WPA2-PSK Output power 17.5dBm Antenna Internal printed antenna, 2.94dBi Physical and Environmental Driver Support Windows 98se, Windows 2000, Windows ME, Windows XP Continuous Current Consumption Temperature Humidity Dimensions 280mA typ. for receive mode, 410mA typ. for transmit mode Operating: 0o C ~ 40o C, Storage: -10o C ~ 70o C 10% ~ 95% RH, no condensation 77 x 26 x 12 mm (W x H x D) Certifications FCC Part 15.247 for US, ETS 300 328 for Europe, 14