FCC ID: 2AVFA-YESWECAN CAN Go

Get Started with CAN Go User Manual Step 1 Wake it up Press the scroll button to turn on the smart cane Scroll button Step 2 Activate it Visit the activation link below to set up an emergency contact that you can call directly from your smart cane www.can.co/activate Step 3 Adjust the height Step 1: Twist the collar towards you to loosen, then push the button. Collar Step 2: Extend the shaft until the button snaps to the desired height. Step 3: Twist the collar away from you to tighten and lock the cane. Collar Step 4 Set up the charger Step 1 Find a convenient location to charge your smart cane daily. Step 2 Peel the tape strips from the back of the charger mount, then press it into the wall (at stomach height) for 30 seconds. Step 3 Finally, plug the charger cord into the AC adapter, then into an electrical outlet (or extension cord). Step 5 Charge it Place the smart cane securely onto the charger. Its charging when you see the battery charging icon on the screen and when you feel it vibrate. 1 2 Get to know CAN Go Controls Call button Scroll button Activity light Flashlight Home screen Phone signal Time Battery level LED Flashlight Make phone calls Step 1 Push the call button for 3 seconds. Step 2 Initiate the call. Step 3 Push the call button to end the call. C A L L I N G CALL ENDED Receive phone calls Step 1 Press the call button to pick up. Step 2 Press the call button to end the call. CALL ENDED Track activity Push the scroll button to view steps, miles and minutes Achieve activity goals The light turns green when youve met your daily activity goals Troubleshooting What to do if the home screen freezes Press the call and scroll button simultaneously for 17 seconds How to remove the charger from the wall Step 1 Pull the wall mount away from the wall. Step 2 Pull the velcro tape attached to the wall down from the tip. Safety and Regulatory Information IMPORTANT PRODUCT SAFETY AND REGULATORY INFORMATION CAN Mobilities Smart Cane Trade Name: CAN Go FCC ID: 2AVFA-YESWECAN Model: CAN Go Type: Smart Walking Cane Location of the FCC ID and other regulatory information, and compliance marks on your device:

The FCC ID and other regulatory information can be found in the device with the following steps: 1) From the Home screen, long press the Flashlight button; 2) Select: Info 3) Select:

Legal & Regulatory by clicking on the power (center) button. FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2)this device must accept any including interference that may cause undesired operation. interference received, Caution: The changes or modications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. installed and used This equipment generates, uses and can radiate radio frequency energy and, in if not accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a installation. If this equipment does cause particular harmful interference to radio or television reception, which can be determined by turning the equipment turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Exposure to radio frequency energy. The radiated output power of this device meets the limits of FCC radio frequency exposure limits. RF Exposure. CAN Go has been tested and meets applicable limits for radio frequency (RF) exposure. The highest SAR values are as follows (visit can.co/pages/rfexposure):

1.6 W/kg (over 1 g) SAR Limit Body (over 1g): 1.44 W/kg Extremity (over 10g): < 0.1 W/kg Maximum RF Output Power of the Product:

BLE: 7 2 dBM LTE: 15 2 Working Frequency Range:

BLE: 2.402 - 2.480 GHz LTE: Bank 2, 4 & 12 Responsible Party (contact for FCC matters):

CAN Mobilities, Inc. 119 Independence Drive | Menlo Park | CA 94025 United States info@canmobilities.com California Proposition 65 WARNING: This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Got questions?

contact hi@canmobilities.com

Vicki Albertson From:

Sent:

To:

Subject:

oetech@fcc.gov Tuesday, January 24, 2023 7:56 AM Vicki Albertson Response to Inquiry to FCC (Tracking Number 814547) (TCB) Importance:

High CAUTION:This email originated from outside of Element Materials Technology. DO NOT click links or open attachments unless you recognize the sender and know the content is safe. Please contact IT Service Desk if you are in any doubt about this email. Inquiry on 01/23/2023 :

Inquiry:

If a device using e-labeling has limited screen space and the full FCC ID number cannot be seen on the screen at one time due to the small size of the screen, is it acceptable to have the text continuously scrolling from left to right so the full FCC ID number is viewable that way?

Please advise. FCC response on 01/24/2023 Hello, Yes we can accept that. Attachment Details:

Do not reply to this message. Please select the Reply to an Inquiry Response link from the OET Inquiry System to add any additional information pertaining to this inquiry. 1

R F C o m p o n e n t s September 2016 Multilayer Antenna For 2400-2484MHz ANT016008LCS2442MA1 1.6x0.8mm [EIA 0603]*

* Dimensions Code JIS[EIA]

R F C o m p o n e n t s Multilayer Antenna For 2400-2484MHz ANT016008LCS2442MA1 Conformity to RoHS Directive SHAPES AND DIMENSIONS

[Top view]

1.600.10 0.40max. 0 1

. 0 0 8

. 0

[Bottom view]

0.200.10

(0.1) 0 1

. 0 3 6

. 0

(1)

(2)

(3)

(6)

(5)

) 1

. 0

(4) Terminal functions 1 Radiator electrode 2 Dummy pad 3 Dummy pad 4 Feed point 5 Dummy pad 6 Dummy pad 0.250.10 0.2150.10 Dimensions in mm RECOMMENDED LAND PATTERN SOLDER RESIST PATTERN 1.60 0.90 0.60 1 2

. 0 1.53 0.90 0.60 3 7

. 0 0 8

. 0 Dimensions in mm 1 1

. 0 3 7

. 0 Dimensions in mm RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html All specifications are subject to change without notice.

Before using these products, be sure to request the delivery specifications. 20160926 / rf_ant_ant016008lcs2442ma1_summary R F C o m p o n e n t s ANT016008LCS2442MA1 EVALUATION BOARD Ft-1 ANT016008LCS2442MA1 PCB size : 50mm x 10mm x 1mm Antenna area : 5 x 3 mm Ft-1 Mt Component P/N 6.2pF 0.8pF Mt Measurement condition for Radiation Pattern Chip antenna PCB Z X Er E E Y

All specifications are subject to change without notice.

Before using these products, be sure to request the delivery specifications. 20160926 / rf_ant_ant016008lcs2442ma1_summary Max. 3.0 Typ. 1.60 Linear 5020 53 50 (Nominal) R F C o m p o n e n t s ANT016008LCS2442MA1 ELECTRICAL CHARACTERISTICS Frequency Range

(MHz) 2400 to 2484 Min. Item VSWR Polarization PCB size (mm) Antenna keep-out area (mm) Characteristic Impedance () This is typical antenna performance with the standard PCB. TEMPERATURE RANGE Operating temperature C 40 to +85 Storage temperature C 40 to +85 FREQUENCY CHARACTERISTICS EFFICIENCY AND VSWR 0 1 2 3 4 5 6 7 8

) B d

y c n e c i f f i E 9 10 2.300 11 10 9 8 7 6 5 4 3 R W S V 2.400 2.500 Frequency(GHz) 2 1 2.600 Efficiency Spec (VSWR) VSWR

Tested antenna has been soldered. Evaluation board size is 50x20x1 mm.

All specifications are subject to change without notice.

Before using these products, be sure to request the delivery specifications. 20160926 / rf_ant_ant016008lcs2442ma1_summary R F C o m p o n e n t s ANT016008LCS2442MA1 RADIATION PATTERNS 2.4GHz BAND 315 0 10(dBi) 0 10 20 30 40 45 315 90 270 0 10(dBi) 0 10 20 30 40 45 90 Y 270 270 Z 0 90 X 225 135 180 Horizontal polarization 2442 21.5 18.5 40.8 2400 21.5 16.9 46.0 Frequency(MHz) Average(dBi) Maximum(dBi) Minimum(dBi) 2400MHz 2442MHz 2484MHz 225 135 180 Vertical polarization 2400MHz 2442MHz 2484MHz 2484 21.3 17.2 36.4 Frequency(MHz) Average(dBi) Maximum(dBi) Minimum(dBi) 2400 0.0 1.3 2.4 2442 0.3 1.6 2.2 2484 0.2 1.2 3.0 315 0 10(dBi) 0 10 20 30 40 45 315 90 270 0 10(dBi) 0 10 20 30 40 50 45 90 270 90 Y 270 0 Z X 225 135 180 Horizontal polarization 2442 2.6 1.6 21.9 2400 2.9 1.3 21.5 Frequency(MHz) Average(dBi) Maximum(dBi) Minimum(dBi) 2400MHz 2442MHz 2484MHz 225 135 180 Vertical polarization 2400MHz 2442MHz 2484MHz 2484 3.1 1.2 23.6 Frequency(MHz) Average(dBi) Maximum(dBi) Minimum(dBi) 2400 24.1 20.2 39.2 2442 24.7 19.1 46.1 2484 24.8 21.5 34.9 315 0 10(dBi) 0 10 20 30 40 Z 270 45 315 90 270 0 10(dBi) 0 10 20 30 40 45 90 270 X 0 90 Y 225 135 180 Horizontal polarization 2442 2.7 0.6 28.5 2400 3.1 0.2 29.8 Frequency(MHz) Average(dBi) Maximum(dBi) Minimum(dBi) 2400MHz 2442MHz 2484MHz 225 135 180 Vertical polarization 2400MHz 2442MHz 2484MHz 2484 3.2 0.1 31.3 Frequency(MHz) Average(dBi) Maximum(dBi) Minimum(dBi) 2400 12.2 8.0 31.2 2442 11.8 7.5 30.5 2484 12.3 8.2 35.8

Tested antenna has been soldered. Evaluation board size is 50201 mm.

All specifications are subject to change without notice.

Before using these products, be sure to request the delivery specifications. 20160926 / rf_ant_ant016008lcs2442ma1_summary R F C o m p o n e n t s RECOMMENDED REFLOW PROFILE Preheating Soldering e r u t a r e p m e T

T T1 t1 6C/sec or lower T3 Peak T4 t3 t2 3C/sec or lower T3 T2 t: Time Preheating Temp. T1 150C T2 200C Time t1 60 to 120sec t3 : Time within 5C of actual peak temperature The maximum number of reflow is 3. Soldering Critical zone (T3 to T4) Time Temp. t2 T3 60 to 120sec 217C Peak Temp. T4 240 to 260C Time t3 30sec max.

All specifications are subject to change without notice.

Before using these products, be sure to request the delivery specifications. R F C o m p o n e n t s ANT016008LCS2442MA1 PACKAGING STYLE REEL DIMENSIONS 2.00.5 0 0

. 1 0

0 6 9.0 +1.0 0.0 13.01.0 Dimensions in mm 130.2 210.8 180 +0 1.5 TAPE DIMENSIONS Material of carrier the tape: PS J G H t E D C B A F K A B 0.970.05 1.80.05 C 8.00.2 D E 3.50.05 1.750.1 F 4.00.1 G 2.00.05 H J K t 4.00.1 1.5+0.1/-0 0.55max. 0.250.05 Dimensions in mm PACKAGE QUANTITY Standard package quantity

(pieces/reel) 4,000

All specifications are subject to change without notice.

Before using these products, be sure to request the delivery specifications. 20160926 / rf_ant_ant016008lcs2442ma1_summary R F C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. Please understand that we are not responsible for any damage or liability caused by use of the products in any of the applications below or for any other use exceeding the range or conditions set forth in this catalog.

(1) Aerospace/Aviation equipment

(2) Transportation equipment (cars, electric trains, ships, etc.)

(3) Medical equipment

(4) Power-generation control equipment

(5) Atomic energy-related equipment

(6) Seabed equipment

(7) Transportation control equipment

(8) Public information-processing equipment

(9) Military equipment

(10) Electric heating apparatus, burning equipment

(11) Disaster prevention/crime prevention equipment

(12) Safety equipment

(13) Other applications that are not considered general-purpose applications When using this product in general-purpose applications, you are kindly requested to take into consideration securing protection circuit/

equipment or providing backup circuits, etc., to ensure higher safety.

All specifications are subject to change without notice.

Before using these products, be sure to request the delivery specifications. 20160926 / rf_ant_ant016008lcs2442ma1_summary

Sample Attestation Statement -FCC Date: February 8, 2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Re: Attestation regarding covered equipment and the Covered List FCC ID: 2AVFA-YESWECAN To whom it may concern, Per 2.911(d)(5)(i), CAN Mobilities Inc. certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Per 2.911(d)(5)(ii), CAN Mobilities Inc. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely, Abdullah Hejazi VP of Software Engineering CAN Mobilities Inc.

CAN Mobilities Inc. DATE: 2022-11-08 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Re: Applicant: CAN Mobilities, Inc. FCC ID: 2AVFA-YESWECAN Enclosed, please find an application for an original equipment certification of module CAN Go; FCC ID:

2AVFA-YESWECAN under Rule Part FCC 15.247 to add Bluetooth low energy to the smart walking cane

(CAN Go) along with the cellular LTE module with FCC ID: 2AVFA-CANGO-4G-EC21. Please let us know if you might require anything further to assist with your review. Best, Abdullah Hejazi Nov 8, 2022

Request for Confidentiality Letter-FCC Date: 2022-11-08 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Re: Request for confidentiality Applicant: CAN Mobilities, Inc. FCC ID: 2AVFA-YESWECAN To whom it may concern, We hereby respectfully request that under the provision of 47 CFR 0.459 and 0.457(d) the documents listed below and attached with this application for certification be provided with confidential status. CAN Go_Bill Of Materials.xlsx CAN Go_Radio_Schematics.pdf Operational Description.pdf Frequency Block Diagrams.pdf Internal Photos (Short-Term for 180 days from the date of the grant) Any exhibit/information for which we have requested confidentiality, but which may not be accorded such treatment by the FCC, should be returned to us. The documents listed above contain trade secrets that are treated as confidential by us. Substantial competitive harm to us could result should they be made available to the public. Sincerely, Abdullah Hejazi VP of Engineering CAN Mobilities Inc.

US Agent Attestation Letter TO: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Re: section 2.911(d)(7) filing To whom it may concern, This letter is to confirm that Abdullah Hejazi has accepted responsibility to act as the agent for service of process as acknowledged by the applicant, CAN Mobilities Inc. U.S. Agent: Abdullah Hejazi FRN 0029047735 Title: VP of Software Engineering Company Name: CAN Mobilities Inc Address: 445 Minnesota Street, Suite 1500, Saint Paul, MN 55101 Telephone No: 310-866-8982 Email: abdullah@canmobilities.com The applicant accepts and acknowledges the obligation to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Signature of Applicant:

Signature of U.S. Agent (if different from applicant):

Name: Abdullah Hejazi Date: March 20, 2023 Name:

Date: