FCC ID: YG2-P120 Bluetooth Module

Canmax technology Ltd. Canmax Technology Ltd. 7F, No.183, Section 1, Tatung Road, His-Chih 22145,Taipei Hsien, Taiwan , R.O.C. TEL886-2-26477797 FAX 886-2-26477798 P120 Bluetooth Module User Manual & Datasheet

(Version 1.0) 1 Canmax technology Ltd. Canmax Technology Ltd. 7F, No.183, Section 1, Tatung Road, His-Chih 22145,Taipei Hsien, Taiwan , R.O.C. TEL886-2-26477797 FAX 886-2-26477798 FCC Regulations:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device is intended only for OEM integrators under the following conditions: 1) The transmitter module may not be co-located with any other transmitter or antenna. As long as the condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). The final end product must be labeled in a visible area with the following: "Contains TX FCC ID: YG2-

P120". IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the 2 Canmax technology Ltd. Canmax Technology Ltd. 7F, No.183, Section 1, Tatung Road, His-Chih 22145,Taipei Hsien, Taiwan , R.O.C. TEL886-2-26477797 FAX 886-2-26477798 OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Description of Operation :

This device is a class 1 Wirless Bluetooth Module provided 2.40GHz~2.48GHz ISM Band frequency hopping spread spectrum (FHSS) with 79 channels and connect up to 7 devices in a pacolet. The maximum transmitting enhanced data rate up to 3Mbps with Bluetooth 2.0+ . The antenna is external PCB type antenna, and use coxial cable to connect the antenna with this module. This Wirless Bluetooth Module compliance with Bluetooth 2.0+ standard. And it can communicate with any Bluetooth 2.0+ network or lower Bluetooth standard. It allows your microcontroller connect to a bluetooth network by using RS232 interface and share data without being bound to the network wires. This Wirless Bluetooth Module firmware support master mode and slave mode and AT command set for operation. And refer to the application circuit for detail hardware connection with microcontroller. In addition. The more details related operations, please refer to the datasheet and firmware command set list. P120 Bluetooth Class I Module :

3 Canmax technology Ltd. Canmax Technology Ltd. 7F, No.183, Section 1, Tatung Road, His-Chih 22145,Taipei Hsien, Taiwan , R.O.C. TEL886-2-26477797 FAX 886-2-26477798 OVERVIEW Highly integration BT 2.0 + EDR Class I module, CSR BC04-EXT + Flash Memory + LNA + PA +

Balun + Filter + XTal. Wireless communications module conforming to Bluetooth Version 2.1 + EDR , Class I. USB, UART, PCM interfaces available to various applications. 8 GPIO ports available for users application. Up to 7 actives devices and up to 3 SCO and eSCO links and up to 7 ACL links Support for Co-existence with WLAN Application, Cellular Phone, PDA, GPS SPP, HS, HF and Other Peripheral Devices

: CSR BC04 External Flash

: Bluetooth

: 2402 ~ 2480 MHz BT Chipset Standards Frequency TX Output Power @ DH5 : Non-EDR, 18.5dBm (max) RX Sensitivity

: Non-EDR, -90dBm (min) Range

: > 100m (open space, line of site) Flash Size

: 8MBits Operation Voltage

: 3.3V Dimension

: 25.5mm x 14mm x 2 mm

: Operation Temperature : 0~+45oC, Relative humidity : 0~95%

Environmental Range 4 Canmax technology Ltd. System Block Diagram Canmax Technology Ltd. 7F, No.183, Section 1, Tatung Road, His-Chih 22145,Taipei Hsien, Taiwan , R.O.C. TEL886-2-26477797 FAX 886-2-26477798 5 Canmax technology Ltd. Canmax Technology Ltd. 7F, No.183, Section 1, Tatung Road, His-Chih 22145,Taipei Hsien, Taiwan , R.O.C. TEL886-2-26477797 FAX 886-2-26477798 Pinout Diagram Note: Please contact Canmax Tech. to get the detail footprint of the module to do the PCB design. 6 Canmax technology Ltd. Canmax Technology Ltd. 7F, No.183, Section 1, Tatung Road, His-Chih 22145,Taipei Hsien, Taiwan , R.O.C. TEL886-2-26477797 FAX 886-2-26477798 Pin No. Pin Name Type Description I/O PIN LISTING 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 SPI_MISO SPI_CLK SPI_MOSI SPI_CSB CMOS output, tri-state, with weak internal pull-down Serial Peripheral Interface data output CMOS input with weak internal pull-down Serial Peripheral Interface clock CMOS input with weak internal pull-down Serial Peripheral Interface data input CMOS input with weak internal pull-up Chip select for Synchronous Serial Interface active low GND Power Ground UART_CTS CMOS input with weak internal pull-down UART clear to send active low PIO[3]

PIO[4]

PIO[5]

PIO[8]

PIO[9]

PIO[10]

PIO[11]

VCC_33 GND USB_DN USB_DP PIO[6]

PIO[7]

PIO[2]

Bi-directional with programmable strength internal pull-up/down Bi-directional with programmable strength internal pull-up/down Bi-directional with programmable strength internal pull-up/down Bi-directional with programmable strength internal pull-up/down Bi-directional with programmable strength internal pull-up/down Bi-directional with programmable strength internal pull-up/down Bi-directional with programmable strength internal pull-up/down Programmable input/output line Programmable input/output line Programmable input/output line Programmable input/output line Programmable input/output line Programmable input/output line Programmable input/output line Power Power Bi-directional Bi-directional Bi-directional with programmable strength internal pull-up/down Bi-directional with programmable strength internal pull-up/down Bi-directional with programmable strength internal pull-up/down 3.3V input Ground USB data minus USB data plus with selectable internal 1.5k pull-up resistor Programmable input/output line Programmable input/output line Programmable input/output line 7 Canmax technology Ltd. 21 22 23 24 25 UART_RTS UART_TX UART_RX ANT GND Canmax Technology Ltd. 7F, No.183, Section 1, Tatung Road, His-Chih 22145,Taipei Hsien, Taiwan , R.O.C. TEL886-2-26477797 FAX 886-2-26477798 UART request to send active low UART data output CMOS output, tri-state, with weak internal pull-up CMOS output, tri-state, with weak internal pull-up CMOS input with weak internal pull-down UART data input Antenna Power Ground Electrical Characteristics Absolute Maximum Ratings :

Supply Voltage Storage Temperature Recommend Operation Conditions :

Supply Voltage Operation Temperature Min.

-

-40 Min. 2.7 0 Typ.

-

-

Typ. 3.3

-

Max. 3.6 85 Max. 3.6 45 Unit V oC Unit V oC Input/Output Terminal Characteristics :

Digital (UART, PIO) VIL Input Voltage Low VIH Input Voltage High VOL Output Voltage Low, (IO is 4mA) VOH Output Voltage High, (IO is -4mA) USB VIL Input Voltage Low VIH Input Voltage High VOL Output Voltage Low VOH Output Voltage High Min. Typ. Max. Unit

+0.8 3.7 0.2

-

0.9

-

0.2 3.3

-

-

-

-

-

-

-

-

-0.4 2.3

-

3.1

-

2.3

-

2.8 V V V V V V V V 8 Canmax technology Ltd. Canmax Technology Ltd. 7F, No.183, Section 1, Tatung Road, His-Chih 22145,Taipei Hsien, Taiwan , R.O.C. TEL886-2-26477797 FAX 886-2-26477798 Radio Characteristics Supply voltage = 3.3V and test under Non-EDR environment Maximum RF transmit power Sensitivity, 0.1% BER 2.402 GHz 2.411 GHz 2.480 GHz RF Power control range RF Power control resolution 20dB bandwidth for modulated carrier f1avg modulation f2max modulation f1avg / f2avg Initial Center Frequency Frequency Drift Rate Frequency Drift (single slot packet) Frequency Drift (five slot packet) Typ 10

-90

-90

-90 22 4.5 700 160 168 1.04 Min

-5 20 4.2 150 150 0.95

-25

-15

-10

-10 23 5.1 800 170 180 1.2 25

+15

-20

-25 Unit dBm dBm dBm dBm dB dB kHz Max 18.5 Bluetooth Spec. 20 -6

-70 16 2 8 1000 40 < f1avg < 175 115 0.80 75 20 25 40 KHz KHz/50us KHz KHz 9 Canmax technology Ltd. Power Consumption Average Current Consumption Canmax Technology Ltd. 7F, No.183, Section 1, Tatung Road, His-Chih 22145,Taipei Hsien, Taiwan , R.O.C. TEL886-2-26477797 FAX 886-2-26477798 HW version FW version BT Host SPP device Power On No connection Open Inquiry Scan Connecting P120 V1.0 HID-SPP-AT-V100-T028 SPP B Sniff disable Deep Sleep enable Role: Slave Baud Rate:115200 General perpose dongle with Bluesoleil 5.0.5.178 Min. 8.01mA 26.67mA Connected No Data Transfer 12.28mA Connected TX 10 digits/sec 12.32mA Connected TX 1 digit/sec 12.23mA Avg.

(1 Min. 1sample/sec) 8.70mA 31.39mA 15.11mA 15.88mA 15.85mA Max 23.23mA 39.85mA 19.17mA 22.33mA 22.65mA 10 Canmax technology Ltd. Dimension Canmax Technology Ltd. 7F, No.183, Section 1, Tatung Road, His-Chih 22145,Taipei Hsien, Taiwan , R.O.C. TEL886-2-26477797 FAX 886-2-26477798 11 Canmax technology Ltd. Application Circuit Canmax Technology Ltd. 7F, No.183, Section 1, Tatung Road, His-Chih 22145,Taipei Hsien, Taiwan , R.O.C. TEL886-2-26477797 FAX 886-2-26477798 12 Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC statement in Users Manual (for class B) Federal Communications Commission (FCC) Statement This Equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-

-

-

-

FCC Caution:

1. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. 2. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. 3. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. FCC WARNING The modification of wireless broadband and other transceiver devices to operate on unauthorized frequencies or the disabling of DFS or TPC capabilities is a violation of FCC rules and may result in unlawful interference to radio communications services critical to public safety. 19