R2 : Confidential ZV-223
(RMN : PP2002) INSTANT CAMERA PRINTER USER MANUAL FOR COMPLIANCE USE Updated : 2020.02.28 1 SAFETY INFORMATION READ BEFORE USE Please read the following instructions and safety precautions before using the device. For regulatory and additional safety information, refer to the Regulation and Warranty Information sheet included in your package contents. RMN : PP2002 Regulatory Model Identification Number is assigned for regulatory identification purpose. WARNING Keep away from children and infants. Improper use of this product may cause suffocation or accident. Stop using the device immediately if it emits smoke or a strange smell, or otherwise behaves abnormally. Do not look at the sun or bright lights through the viewfinder or the lens. Blindness or vision problems could result. Do not fire the flash near the eyes. It may hurt the eyes. A strap wound around a childs neck may result in asphyxiation. If your product uses a power cord, mistakenly winding the cord around a childs neck may result in asphyxiation. Turn the device off in places where camera use is prohibited. The electromagnetic waves emitted by the camera may interfere with operation of electronic instruments and other devices. Exercise adequate caution when using the product in places where use of electronic devices is restricted, such as inside airplanes and medical facilities. CAUTION When operating in extreme weather, the device might not print. Let the printer temperature adjust to the recommended operating temperature of 59 to 90 F (15 to 32 C), before attempting to print again. When charging, please charge the device at the recommended temperature of 59 to 90 F (15 to 32 C). Use a soft dry cloth to clean the device. Do not clean with a damp cloth or volatile liquids such as paint thinner. Keep the top cover closed to avoid dust and other particles from entering the inside of the device. If the device is not functioning properly, please contact the dealer you purchased this product from or Canon Service & Support at www.usa.canon.com/support Never expose the battery to high temperatures, direct heat, or dispose by incineration. Electromagnetic interference or electrostatic discharge may cause the device to malfunction or the memory to be lost or altered. Should this occur, use a pin, or similar item to press the [RESET] button at the bottom of the device. 2 GETTING STARTED CHARGING Charging Status LED Charging : Red Full : Green The device has a built-in battery. Please fully charge the device via the USB cable provided before using. 1. Insert the smaller end of the supplied USB cable into the device and other end into a chargeable USB adapter. The charging LED light, at the bottom of the device, will turn red to indicate charging. 2. 3. Once fully charged, the charging LED will turn green.
- Operating time may vary depending on the battery status, operational status and environment conditions. INSERTING SD CARD An external MicroSD card (up to 256 GB) is needed for saving captured photos. Only FAT16, FAT32 and exFAT format are supported. PREPARING A MEMORY CARD Use the following memory cards (sold separately) MicroSD memory cards *1 MicroSDHC memory cards *1*2 MicroSDXC memory cards *1*2
*1 Cards conforming to SD standards. However, not all memory cards have been verified to work with the camera.
*2 UHS-I memory cards are also supported. INSTALL AND REMOVE THE MicroSD CARD Insert the MicroSD card into the slot at the bottom of the device. You will feel a slight click when the card is fully inserted. Push on the top of the card to release it. Gently pull to fully remove the card from the device. If there is an error on ready / writing to the MicroSD card, the MicroSD Error LED Indication will be displayed. Connect the device to a computer by USB cable. Double-click the external drive image when it appears on the computer to view and save the photos. 3 OPERATION POWER ON/OFF 1. Press and hold the Power Button unit the LED indicator light turns on. 2. When the LED indicator turns to a steady white, the device is ready to use. 3. Press and hold the Power Button to turn off the device. AUTO POWER OFF When the device is idle for about 3 minutes (default), it will automatically power off. User can resume the device by pressing the Power Button again. User can change the time (3 minutes / 5 minutes / 10 minutes) in the App. CAMERA MODES You can select the different camera modes by the Slide Switch at the top of the device for different scenarios. Slide Switch Mode Description Outdoor Portrait Flash Off Auto Flash Selfie Ring Light and Flash ON TAKING A PHOTO 1. Hold the device, confirm the desired composition of the image. 2. Press the Shutter Button to take a photo.
- Half press for focus lock
- Full press to take a photo 4 Status Power On LED INDICATIONS Operation LED Indicator Press and hold Power Button Standby After the device is powered on Power Off Press and hold Power Button SMART SHEETTM Error Processing SMART SHEETTM When the device detects wrong SMART SHEETTM is inserted, or other SMART SHEETTM error When the device is printing out SMART SHEETTM No Paper When the device has no paper Paper Jam / Cover Open When there is a paper jam or the printer cover is opened Get Ready for Printing When the device is preparing for printing Printing Photo When the device is printing a photo MS Mode (Mass Storage Mode) Device is connected to a computer MicroSD Card Error When the device cannot write data into MicroSD Card Temperature Too High When device temperature is too high Temperature Too Low Printer Head Cooling When device temperature is too log When the device is checking the printer head temperature and letting it cool down before printing 5 Low Battery When battery level down to 20%
Very Low Battery When battery level is very log Firmware Updating When the device is updating firmware Selfie Photo When the device is taking a photo in Selfie Mode
(Ring Light) 6 Printing Speed Approximately 50 seconds Motor starts and stops, at room temperature 77 F (25 C) SPECIFICATIONS Printing Technology ZINK Printing Resolution 314 x 600 dpi (dots per inch) Photo Aspect Ratio 2 x 3 Compatible Paper Canon ZINK Photo Paper :
ZP-2030-20 (20 sheets) ZP-2030-50 (50 sheets) 2 x 3 / Peel-and-Stick Back Paper Capacity Up to 10 sheets of ZINK photo paper + 1 SMART SHEETTM Photo Resolution Focal Length Aperture Focusing Range Sensitivity Flash Flash Range Memory Card Power Source 8MP 2.6mm f 2.2 1 ft -
Auto (ISO 100 1600) YES (Auto) 1.6ft 3.2ft MicroSD Card, up to 256 GB Built-in Rechargeable Li-Polymer Battery 700mAh, 7.4V Charging Speed Approximately 120 minutes (Full Charge) Power Adapter Output Current : 1A (min) Voltage : 5V Environmental Parameters 90 F (15 to 32 C)
- Recommended Printing Operating, Charging, and Storage Temperature : 59 to
- Recommended Printing Operating, Charging, and Storage Humidity : 40-55% RH
- Operating Temperature : 41 to 104 F (5 to 40 C)
- Operating Humidity : < 70% RH Automatic Power-off 3 minutes / 5 minutes / 10 minutes (selectable in app) Dimension 4.8 (W) x 3.1 (H) x 0.9 (D) 121mm (W) x 80.3mm (H) x 22.5mm (D) Weight 6.6 oz / 188 g Compatible OS
(for Computer) Connectivity Window 7 / 8 / 8.1 / 10 Mac OSX 10.10 10.15 Bluetooth 5.0 Mobile Application Canon Mini Print Connection for Charging and Data Transfer Subject to change without notice. USB 2.0 (Mirco USB) Compatible OS iOS 9.0 or above, and Android 4.4 or above 7 8 ZV-223 RMN : PP2002 ENGLISH technician for help. Consult the dealer or an experienced radio/TV Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be required to stop operation of the equipment. RMN : PP2002 Regulatory Model Identification Number is assigned for regulatory identification purpose. FCC REGULATIONS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. WARNING : Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC Statement to the User : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. WARRANTY : 1 year limited warranty. For full terms and conditions, visit www.usa.canon.com/support (For USA Customer) www.canon.ca/support (For Canada Customer) Canada Compliance RF Radiation Exposure Statement
"This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device."
FOR PORTABLE DEVICE USAGE (<20cm from body/SAR needed) Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. PMN : Instant Camera Printer Internal rechargeable battery 700 mAh Li-Polymer 7.4 V SPECIFICATIONS Power Source:
Connectivity: Bluetooth 5.0 Operating Temperature (Printing): 41 to 104F / 5 to 40C Operating Humidity: <70%RH Recommended Operating and Charging Temperature:
59 to 90F (15 to 32C) Recommended Operating Humidity: 40-55%RH Dimension: 4.8"(W) x 3.1" (H) x 0.9" (D) /
Weight: 6.6 oz (188 g) Automatic Power-off: 3 minutes / 5 minutes / 10 minutes NOTE: All specifications are subject to change without notice. 121 mm (W) x 80.3 mm (H) x 22.5 mm (D)
(selectable In-App) FRANAIS RMN : PP2002 Le numro d'identification du modle rglementaire est attribu des fins d'identification rglementaire. RGLEMENT DE LA FCC Cet appareil est conforme la partie 15 du rglement de la FCC. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage prjudiciable; et
(2) lappareil doit accepter tout brouillage subi, mme si le brouillage est susceptible den compromettre le fonctionnement. MISE EN GARDE : Tout changement ou toute modification apport(e) cette unit qui na pas t approuv(e) expressment par la partie voyant sa conformit risque d'annuler l'autorisation de l'utilisateur faire fonctionner l'quipement. Dclaration de la FCC l'utilisateur : Cet quipement a t test et dclar conforme aux limites pour un appareil numrique de classe B, conformment la partie 15 du rglement de la FCC. Ces limites sont conues pour offrir une protection raisonnable contre le brouillage prjudiciable dans une installation rsidentielle. Cet quipement produit, utilise et peut mettre de l'nergie de frquence radio et, s'il n'est pas install et utilis conformment aux instructions, peut occasionner un brouillage prjudiciable aux communications radio. Cependant, il n'existe aucune garantie l'effet qu'une installation particulire ne produira aucun brouillage. Si cet quipement produit un brouillage prjudiciable la rception radiophonique ou tlvisuelle, ce que vous pouvez dterminer en teignant et rallumant l'quipement, nous encourageons l'utilisateur essayer de corriger le brouillage laide d'une ou de plusieurs des faons suivantes :
Rorienter ou repositionner l'antenne de rception. Augmenter la sparation entre l'quipement et le rcepteur. Brancher l'quipement dans la prise d'un circuit autre quecelui auquel le rcepteur est branch. Consulter le distributeur ou un technicien radio/TV expriment pour toute assistance. N'apportez aucun changement ou aucune modification l'quipement moins que le manuel le/la spcifie. Si vous faites pareil changement ou pareille modification, vous pourriez avoir arrter dutiliser l'quipement. Dclaration d'exposition aux radiations:
Le produit est conforme la limite d'exposition RF de la FCC dfinie pour un environnement non contrl et peut tre utilis en toute scurit, comme dcrit dans ce manuel. Une rduction supplmentaire de l'exposition aux RF peut tre obtenue si le produit peut tre tenu aussi loin que possible du corps de l'utilisateur ou si le priphrique est rgl sur une puissance de sortie infrieure si cette fonction est disponible. Cet metteur ne doit pas tre situ au mme endroit ni fonctionner avec une autre antenne ou un autre metteur. GARANTIE : Garantie limite d'un an. Pour toutes les conditions et modalits, visitez www.usa.canon.com/support (Pour les tats-Unis) www.canon.ca/support (Pour le client du Canada) Conformit au Canada Dclaration d'exposition aux radiations RF Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage; et
(2) lappareil doit accepter tout brouillage, mme si le brouillage est susceptible de compromettre le fonctionnement de l'appareil . POUR LUTILISATION DUN APPAREIL PORTABLE
(<20 m du corps / SAR ncessaire) Dclaration d'exposition aux radiations:
Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada tablies pour un environnement non contrl. Le produit est sr pour un fonctionnement tel que dcrit dans ce manuel. La rduction aux expositions RF peut tre augmente si l'appareil peut tre conserv aussi loin que possible du corps de l'utilisateur ou que le dispositif est rgl sur la puissance de sortie la plus faible si une telle fonction est disponible. PMN : Appareil photo instantan imprimante SPCIFICATIONS Alimentation : Pile rechargeable interne 700 mAh Li-Polymer 7,4 V Connectivit : Bluetooth 5.0 Temprature d'utilisation (impression) : 41 104 F / 5 40 C Humidit de fonctionnement : HR < 70 %
Temprature de fonctionnement et de charge recommande :
59 90 F (15 32 C) Humidit de fonctionnement recommande : 40-55%HR Dimensions : 4,8 po (L) x 3,1 po (H) x 0,9 po (P) /
Poids : 6,6 oz (188 g) Mise hors tension automatque : 3 minutes / 5 minutes /
REMARQUE : Toutes les spcifications sont susceptibles dtre modifies sans pravis. 10 minutes (slection dans lappli) 121 mm (L) x 80,3 mm (H) x 22,5 mm (P) E-PO-1315 RMN : PP2002 El Nmero de Identificacin del Modelo Regulatorio se asigna para fines de identificacin reglamentaria. ESPAOL Regulaciones de la FCC Este dispositivo cumple con la Parte 15 de las reglas de la Comisin Federal de Comunicaciones (Federal Communications Commission, FCC). La utilizacin de este equipo est sujeta a las dos condiciones siguientes:
(1) Este dispositivo no causa interferencia perjudicial y
(2) este dispositivo debe aceptar cualquier interferencia, incluso toda interferencia que pueda causar un funcionamiento no deseado. ADVERTENCIA: Los cambios y las modificaciones a esta unidad que no estn expresamente aprobadas por la parte responsable de cumplimiento pueden anular el permiso del usuario para utilizar el equipo. Declaracin de la FCC para el usuario: Este equipo se prob y cumpli con los lmites para un dispositivo digital clase B, conforme a la Parte 15 de las reglas de la FCC. Estos lmites estn diseados para brindar una proteccin razonable frente a interferencia perjudicial en un establecimiento residencial. Este equipo genera, usa y puede irradiar energa de radiofrecuencia y, si no se instala y usa de acuerdo con las instrucciones, puede causar interferencia perjudicial a las radiocomunicaciones. Sin embargo, no existe garanta de que la interferencia ocurrir en un establecimiento en particular. Si este equipo causa interferencia perjudicial a la recepcin de radio o televisin, que se puede determinar al encender y apagar el equipo, se recomienda que el usuario intente corregir la interferencia mediante una de las siguientes medidas:
Orientar o ubicar de nuevo la antena de recepcin Aumentar el espacio de separacin entre el equipo y la recepcin Conectar el equipo a una salida en un circuito diferente al circuito en el cual est conectada la recepcin Consultar al proveedor o a un tcnico de radio/TV con experiencia para obtener ayuda No realice cambios ni modificaciones al equipo salvo que as se especifique en el manual. Si se realizan cambios o modificaciones, es posible que se le solicite que no contine operando el equipo. Declaracin de exposicin a la radiacin:
El producto cumple con el lmite de exposicin a RF porttil de la FCC establecido para un entorno no controlado y es seguro para la operacin prevista como se describe en este manual. La reduccin adicional de la exposicin a la RF se puede lograr si el producto se puede mantener lo ms alejado posible del cuerpo del usuario o se puede configurar el dispositivo para reducir la potencia de salida si dicha funcin est disponible. Este transmisor no debe colocarse ni funcionar junto con ninguna otra antena o transmisor. GARANTA: Garanta limitada de 1 ao. Para conocer todos los trminos y condiciones, visite www.usa.canon.com/support (Para el cliente de Estados unidos) www.canon.ca/support (Para el cliete de Canad) Cumplimiento para Canad Declaracin sobre la exposicin a la radiacin de radiofrecuencia
"Este dispositivo cumple con las especificaciones para regulaciones de radios (Radio Standards Specification, RSS) de exencin de licencia de la industria de Canad. La utilizacin de este equipo est sujeta a las dos condiciones siguientes:
(1) Este dispositivo no causa interferencia perjudicial y
(2) Este dispositivo debe aceptar cualquier interferencia, incluso toda interferencia que pueda causar un funcionamiento no deseado". PARA USO DE DISPOSITIVOS PORTTILES
(se necesitan <20 m desde el cuerpo / SAR) Declaracin de exposicin a la radiacin:
El producto cumple con el lmite de exposicin a RF porttil de Canad establecido para un entorno no controlado y es seguro para la operacin prevista como se describe en este manual. La reduccin adicional de la exposicin a la RF se puede lograr si el producto se puede mantener lo ms alejado posible del cuerpo del usuario o se puede configurar el dispositivo para reducir la potencia de salida si dicha funcin est disponible. PMN: Impresora de cmara instantnea 41 a 104F (5 a 40 C) de polmero de litio 700 mAh 7.4 V ESPECIFICACIONES Fuente de energa: Batera interna recargable Conectividad: Bluetooth 5.0 Temperatura de funcionamiento (impresin):
Humedad de operacin: <70% HR Temperatura recomendada de operacin y carga Humedad recomendada de operacin: 40-55%HR Dimensiones: 4,8" (An.) x 3,1" (Al.) x 0,9" (Pr.) /
Peso: 6,6 oz (188 g) Apagado automtico : 3 minutos / 5 minutos / 10 minutos NOTA: Todas las especificaciones estn sujetas a cambio sin previo aviso. 121mm (An.) x 80,3 mm (Al.) x 22,5mm (Pr.)
(seleccionable en la aplicacin) 59 a 90F (15 a 32C) Battery Caution / Prcautions relatives la pile /
Precaucin con la Batera Please call 1-800-8-BATTERY for information on how to recycle this battery. U.S.A and Canada only The lithium ion/polymer battery is recyclable. EN FR Les Etats-Unis et le Canada seulement La batterie aux ons de lithium est recyclable. Pour obtenir des renseignements sur les faons de recycler cette batterie, veuillez appeler au 1-800-8-BATTERY. ES Los EE.UU. y Canad solamente La batera de ion de litio es reciclable. Llame por favor 1-800-8-BATTERY para la informacin sobre cmo reciclar esta batera. CANON ELECTRONIC BUSINESS MACHINES (H.K.) CO., LTD. 17/F., Tower One, Ever Gain Plaza, 82-100 Container Port Road, Kwai Chung, New Territories, Hong Kong CANON U.S.A., INC. One Canon Park, Melville, NY 11747, 1-800-OK-CANON CANON CANADA INC. 8000 Mississauga Road, Brampton, ON, L6Y 5Z7, Canada CANON ELECTRONIC BUSINESS MACHINES (H.K.) CO., LTD. 2020 E-PO-1315