FCC ID: Q95ER01 Bluetooth Motorcycle Headset

scala-rider manual DRAFT APRIL 25, 2005 scala-rider User Manual Page 1 of 31 scala-rider manual DRAFT APRIL 25, 2005 Table of contents 1 INTRODUCTION ..................................................................................................... 4 2 WAIVER AND GENERAL RELEASE ..................................................................... 4 3 RETAIL PACKAGE CONTENTS. .......................................................................... 7 4 BEFORE USING THE HEADSET ........................................................................... 8 Charging Batteries.....................................................................................................................................9 4.1 Attaching and removing the scala-rider from your helmet .............................................................9 4.2 4.2.1 First installation ........................................................................................................................................9 4.2.2 Removing the headset from the helmet. ...........................................................................................11 4.2.3 Re-attaching the headset to the helmet. ...........................................................................................11 5 GETTING STARTED WITH THE SCALA-RIDER HEADSET............................... 12 Pairing process.........................................................................................................................................12 5.1 Power On/Off .............................................................................................................................................13 5.2 5.3 Renewed Pairing.......................................................................................................................................13 Reconnecting the scala-rider headset to a paired phone..............................................................13 5.4 6 HANDLING CALLS............................................................................................... 14 Initiating calls by using your phones keypad..................................................................................14 6.1 6.2 Voice Dialing..............................................................................................................................................14 Answering Calls (including Special Voice Recognition)................................................................14 6.3 6.4 Terminating Calls .....................................................................................................................................15 Volume Control.........................................................................................................................................15 6.5 6.6 Call Reject ..................................................................................................................................................16 7 VOICE RECOGNITION FEATURE ....................................................................... 16 Enable/Disable the Voice Recognition feature .................................................................................16 7.1 Answering calls using Voice Recognition.........................................................................................17 7.2 7.3 Rejecting calls using Voice Recognition ...........................................................................................17 Page 2 of 31 scala-rider manual DRAFT APRIL 25, 2005 8 OPERATING THE RADIO..................................................................................... 17 Turning the radio on/off..........................................................................................................................17 8.1 8.1.1 Turn the radio on .................................................................................................................................17 8.1.2 Turn the radio off.................................................................................................................................17 8.2 8.3 Switching preset radio station..............................................................................................................17 Searching for and saving a new radio station..................................................................................18 8.3.1 Enter search mode..............................................................................................................................18 8.3.2 Saving radio station............................................................................................................................18 9 OPERATING THE REMOTE CONTROL .............................................................. 19 CTRL_RC button usage..........................................................................................................................19 9.1 9.1.1 Power Off...............................................................................................................................................19 9.1.2 Initiate voice dial..................................................................................................................................19 9.1.3 Answering Calls...................................................................................................................................19 9.1.4 Terminating Calls ................................................................................................................................19 9.1.5 Rejecting Calls .....................................................................................................................................20 9.2 Radio_RC button usage..........................................................................................................................20 9.2.1 Power ON/OFF......................................................................................................................................20 9.2.2 Change radio station ..........................................................................................................................20 9.2.3 Search radio station............................................................................................................................20 Remote control functionality table ......................................................................................................20 9.3 10 LIGHT AND SOUND SIGNALS......................................................................... 21 11 12 13 14 15 16 17 18 19 FAQS ................................................................................................................. 22 LIMITED WARRANTY....................................................................................... 24 TROUBLESHOOTING....................................................................................... 27 FCC NOTICE ..................................................................................................... 29 TECHNICAL SPECIFICATION.......................................................................... 29 EUROPEAN CE NOTICE .................................................................................. 30 CONTACT INFORMATION ............................................................................... 31 SERVICE ........................................................................................................... 31 PATENT, COPYRIGHT, TRADEMARK INFORMATION .................................. 31 Page 3 of 31 scala-rider manual DRAFT APRIL 25, 2005 Introduction 1 Congratulations and thank you for purchasing the scala-rider Bluetooth headset for motorcycle helmets. Now you can wear your helmet while talking hands-free on your Bluetooth enabled mobile phone, made possible by the short-range wireless connection between your cell phone and the scala-rider headset. If you are using a standard non-Bluetooth mobile phone, you can still enjoy the headsets advantages by connecting our BT Adapter to your mobile phone (purchased separately). The scala-rider headset is compatible with the latest Bluetooth v1.2 specifications, as well as the earlier Bluetooth v1.1 specifications. Please read and familiarize yourself with all the instructions, components and controls of your scala-rider headset prior to first use. We wish you a great scala-rider experience. 2 Waiver and General Release By using the scala-rider you will waive substantial legal rights including the right to sue. Please read the following carefully before deciding to open the retail package and using the Device. If you do not accept the terms of this agreement, you should immediately return the product for a full refund. By opening the package you agree to be bound to this agreement and forfeit the right for a full refund. Using any tool or device including but not limited to situations such as riding a motorcycle, scooter, moped, ATV, quad-bike or any other vehicle, whether on land, water or air (jointly referred to as Vehicle) requires your complete und undivided attention. Cardo Systems, Inc., including its Officers, Directors, Affiliates, Parent Company, Representatives, Agents, Contractors, Sponsors, Employees, Suppliers and Resellers (jointly referred to as the Company or Cardo) strongly advises you to take all necessary precautions and remain alert to the traffic, weather and road conditions when using the scala-rider headset, including all derivative models irrespective of its commercial name or branding (the Device), and stop your Vehicle on the roadside prior to initiating or receiving calls or listening to the radio that is provided by a particular model of the Device. Any publications, advertisements, announcements or similar notes that refer to using the Device while riding a Vehicle are solely intended to address its technical capabilities and should not be misconstrued as if encouraging users to using it while actively involved in traffic. By way of purchasing this Device and not returning it for a full refund (see below), you are irrevocably releasing, indemnifying from any liability, loss, claim and expense (including attorneys' reasonable fees) and holding Cardo harmless for any bodily injuries, harm or death Page 4 of 31 scala-rider manual DRAFT APRIL 25, 2005 as well as losses or damages in goods, to any Vehicles including your own, or to any property or assets that belong to you or third parties, any of which may result from using the Device under any circumstances or conditions and irrespective of jurisdiction. Cardo will not be responsible for any physical damages, irrespective of reasons, conditions or circumstances, including malfunctioning of the Device, and all risks associated with the using it rest solely and entirely with the user of this Device, irrespective of whether the Device is used by the original purchaser or any third party. Cardo hereby notifies you that using this Device may also be in contravention to local, federal, state or national laws or regulations, and that any use of the Device is entirely at your sole risk and responsibility. 1. forever release, discharge, indemnify and hold harmless Cardo from any and all litigation, claims, debts, demands, actions and liability which may arise, directly or indirectly, from using the Device for any distress, pain, suffering, discomfort, loss, injury, death, damages to or in respect to any person or property however caused, WHETHER ARISING FROM THE NEGLIGENCE OR OTHERWISE, and which may hereafter accrue to you on some future date as a result of said usto the fullest extent permitted by law. 2. negligent acts or omissions by others and accept the terms and conditions upon which you have chosen to use it. You, your heirs, legal representatives, successors or assigns, hereby voluntarily and You fully understand and assume the risks in using the Device, including risk of You confirm that you are physically capable to use the Device and that you have no 3. medical conditions or needs that may infringe upon your abilities to do so in a safe manner. You confirm that you are at least eighteen (18) years of age and that you have been advised of the risks associated with the use of the Device. You further confirm that you will not consume any alcohol that may affect your alertness or any mind-altering substance, and will not carry, use or consume these substances before or during the use of the Device. 4. You fully acknowledge our warnings and understand that: (a) risks and dangers exist in using the Device while in traffic, incl. but not limited to injury or illness, strains, fractures, partial and/or total paralysis, death or other ailments that could cause serious disability; (c) these risks and dangers may be caused by the negligence of the manufacturers or its agents or any third party involved in designing the Device; (d) these risks and dangers may arise from foreseeable or unforeseeable causes. You hereby assume all risks and dangers and all responsibility for any losses and/or damages, whether caused in whole or in part by the negligence or other conduct of others, including the Company. 5. You confirm that you have read this release of liability and fully understand its terms and that you have given up substantial rights by not returning the Device for a full refund (see refund option below). Page 5 of 31 scala-rider manual DRAFT APRIL 25, 2005 Disclaimer of Warranty CARDO DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES WITH REGARD TO THE ENCLOSED DEVICE, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT. THE DEVICE AND ITS ACCESSORIES ARE PROVIDED "AS IS"

AND "AS AVAILABLE" WITHOUT WARRANTY OF ANY KIND BETOND THOSE ASSUMED IN THE ENCLOSED MANUAL. Limitation of Liability IN NO EVENT SHALL CARDO BE LIABLE FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THE DEVICE, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. YOU ACKNOWLEDGE AND AGREE THAT THE LIMITATIONS SET FORTH ABOVE ARE FUNDAMENTAL ELEMENTS OF THIS AGREEMENT AND THE DEVICE WOULD NOT BE PROVIDED TO YOU ABSENT SUCH LIMITATIONS. SOME STATE STATUTES MIGHT APPLY REGARDING LIMITATION OF LIABILITY. RETURN FOR FULL REFUND IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONDITIONS, YOU MAY RETURN THIS DEVICE TO CARDO FOR A FULL REFUND, PROVIDED THAT YOU DO SO NO LATER THAN 7 BUSINESS DAYS FOLLOWING THE PURCHASE OF THE DEVICE (proof of purchase required) AND SUBJECT TO THE WRAPPING BEING INTACT. WHEN DOING SO, PLEASE REFER TO THIS SECTION. BY NOT RETURNING THE DEVICE FOR REFUND WITHIN THE PERIOD PROVIDED, YOU ARE EXPLICITELY IN AGREEMENT WITH THE ABOVE, AND RENOUNCE ALL RIGHTS TO FUTURE CLAIMS AND DEMANDS AGAINST CARDO AS DEFINED ABOVE. Page 6 of 31 scala-rider manual DRAFT APRIL 25, 2005 Retail Package Contents. 3 Your retail package contains the following items:

Headset Clamp Remote control Big microphone sponge small microphone sponge plastic extension for the helmet unit Allen wrench Wall Charger (universal travel version) CD-Manual & Quick Guide Warranty + Registration Card Headset Clamp Quick guide and multilingual manual on mini-VD Wall Charger Remote Control Big sponge Small sponge Allen wrench Page 7 of 31 scala-rider manual DRAFT APRIL 25, 2005 Volume down button Press to decrease the volume Before using the headset Radio button Radio ON/OFF Changing radio stations 4 Read and familiarize yourself with all instructions, components and controls of your scala-rider headset prior to first use. CTRL (control button) Press on the logo. Accept/initiate calls End/Reject calls Power ON/OFF Charge the headset by inserting the Wall-charger into the charging socket Volume Up button Press to increase the volume Reel of the clamp Charging socket Microphone Speaker Page 8 of 31 scala-rider manual DRAFT APRIL 25, 2005 4.1 Charging Batteries Make sure the headset is fully charged prior to initial use. Allow at least six hours for a full charge before using for the first time. Normally 5-6 hours will suffice for complete charge. The headset should be off the helmet when being charged (solely for purposes of convenience) Plug the Wall Charger into the charging socket of the headset and connect it to an electrical outlet. The Red Light Indicator (LED) on the scala-rider will turn on when charging begins. Allow the headset to charge until the Red LED turns off. When charging is complete, release the headset from the charger. NOTE: You may leave the unit connected even if charging is completed. There is no danger of over-charging. 4.2 Attaching and removing the scala-rider from your helmet 4.2.1 First installation Once the headset is fully charged you should proceed to pair it to your mobile phone (see section 5 below). When done, you can proceed with attaching the unit to your helmet. The clamp serves as the base-cradle for the headset and must be attached to your helmet before using the headset Use the enclosed Allen wrench to loosen the two screws of the clamp (FIG. 1). Then slide the back-plate of the clamp between the internal padding and the external shell of the helmet (FIG. 2). Before fastening the screws, make sure to adjust the clamps location to an ideal position, i.e. to the spot where the attached speaker and microphone are respectively opposite your ear and just slightly off the corner of your mouth (FIG. 3). You may need to re-position the clamp repeatedly until you identify the ideal spot. The speaker can be easily placed into position and removed by means of the Velcro layer that attaches to the inner padding of your helmet. Once you have identified the ideal position for the clamp, use the Allen wrench to fasten the clamp. Now slide the scala-rider headset downward along the reel of the clamp (FIG. 4) until a light clicking sound indicates that the headset has reached its proper operational position. Page 9 of 31 scala-rider manual DRAFT APRIL 25, 2005 Turn on the headset by pressing and holding CTRL for at least 6 seconds until the Blue LED flashes three times and an ascending alert tone is heard. Quickly release the button. You are ready to go!

FIG 1 FIG 2 FIG 3 FIG 4 microphone should be placed just slightly off the corner of your mouth Page 10 of 31 scala-rider manual DRAFT APRIL 25, 2005 4.2.2 Removing the headset from the helmet. The clamp usually stays attached to the helmet, but you can also easily remove it by proceeding in the reverse order of the attachment procedure (see 4.2.1 above) To remove the headset from the clamp, press your finger firmly against the arched tip of the back-plate (FIG. 5) and use the other hand to slide the headset upwards along the reel (FIG. 5) FIG 5 Press here and than slide the headset unit up. 4.2.3 Re-attaching the headset to the helmet. To re-attach the headset, simply slide it downwards along the reel of the clamp (FIG. 4) until a light clicking sound indicates that the headset has reached its proper operational position. Page 11 of 31 scala-rider manual DRAFT APRIL 25, 2005 5 Getting Started with the scala-rider headset Before you can use your headset for the first time, the pairing process between your headset and mobile phone must be completed. Pairing is the required process of mutual recognition between your headset and mobile phone. Please note: Your headset will not work prior to successful completion of the pairing process!

5.1 Pairing process 5.1.1 Turn on the phone and make sure its Bluetooth function is activated. 5.1.2 Press and hold the CTRL button for six seconds until the red and blue LEDs begin flashing rapidly alternating. 5.1.3 On your Bluetooth phone, search for Bluetooth devices by following your phones instructions. Usually this is done by selecting the Search or Discover option in the Bluetooth or Connection menu. Refer to your phones manual for detailed instructions on how to pair your specific phone. 5.1.4 After a few seconds of searching, your phone will list the scala-rider as a discovered device. Select it, and when asked, follow your phones instructions to accept pairing. 5.1.5 When prompted by your phone, enter 0000 (4 zeros) as your PIN or passkey. completed. 5.1.6 Your phone will confirm when pairing has been successfully NOTE: If pairing is not completed within two minutes, the headset will return to Standby mode (flashing Blue every 3 seconds). To pair again, turn off the headset by pressing and holding the CTRL button until the red led flashes three times and repeat the process as shown above (5.1). Congratulations! You have now successfully completed your Bluetooth pairing process and are able to use your scala-rider headset with your mobile phone. From now on, when using your headset, you will no longer need to pair the headset to the phone. The two devices will remain paired until you delete that pairing from the phone. Page 12 of 31 scala-rider manual DRAFT APRIL 25, 2005 5.2 Power On/Off To turn ON, press and hold the CTRL button for at least 6 seconds until the Blue LED flashes three times and an ascending alert tone is heard. Quickly release the button. To turn OFF the headset, press and hold the CTRL button for at least 3 seconds until the Red LED flashes three times and an alert tone is heard. 5.3 Renewed Pairing If you wish to use different phone or in case you need to repeat the pairing process for any other reason, please proceed as follows:

6.3.1 Turn the headset off. 6.3.2 Press the CTRL button for 10 seconds until the red and blue LEDs begin flashing rapidly alternating. 6.3.3 Follow sections 5.1.3 to 5.1.6 above 5.4 Reconnecting the scala-rider headset to a paired phone Although you may have previously paired your headset to your phone, each time you turn one of them off, some phones require that you re-

establish the connection. Reconnecting may also be necessary when your headset and phone have lost the radio signal because the distance between them has exceeded 30 feet or 10 meters. After you have turned on your mobile phone, there are several methods to reestablish the connection:

Turning the headset on should reconnect it automatically to the phone. With some mobile phones you need to reestablish the link to your headset by using your phones menu. Please refer to your mobile phones manual for operating instructions. Assuming your mobile phone features voice activation, tap the CTRL button on your scala-rider headset. This will activate your voice dial function on the phone, indicating that the connection is established. Do nothing. Once a call is received, answer by pressing the CTRL button. Page 13 of 31 scala-rider manual DRAFT APRIL 25, 2005 6 6.1 Handling Calls NOTE: Certain advanced features of the scala-rider are only accessible to phones equipped with the hands-free profile. Please check if your phone supports both the headset and the hands-free profile. Initiating calls by using your phones keypad a. Dial the phone number on your phones keypad. b. Press Talk or Send on your phone to dial the number. 6.2 Voice Dialing While your phone is ON but no call is in progress, tap the CTRL button, which will be followed by a tone. Now pronounce the name of the party you wish to call and wait for feedback from the phone. The type of feedback depends on your phone. To improve voice tag recognition, use the headset to record voice tags on your phone (if possible). 6.3 Answering Calls (including Special Voice Recognition) The ringtone for incoming calls increases gradually. When hearing the ring tone (on the headset), there are two ways you can answer the call:

- Tap the CTRL button on your headset once (FIG. 6)

If the Voice Recognition (VR) feature is, you have 7 seconds available to utter any word of your choice in order to accept the call. If you remain silent for 7 seconds the call will be automatically rejected and the ringing will stop. Page 14 of 31 scala-rider manual DRAFT APRIL 25, 2005 6.4 Terminating Calls To terminate a call, tap the CTRL button, followed by a tone confirming the termination. If the other party terminates the call first, you don't have to do anything. Wait at least three seconds before pressing the CTRL button again to start voice dialing. Tap here to terminate the call FIG. 7 The scala-rider headset comes equipped with AGC technology to automatically adjust itself to the optimal speaker volume. Its embedded sensors continuously measure the ambient noise and driving speed to make manual adjustment of the volume buttons unnecessary. You can override the automatic volume adjustment anytime by manual control of the volume buttons one step at a time (FIG. 8). For each step of adjustment, you will hear a short beep. 6.5 Volume Control FIG.8 Press here to increase the volume Press here to decrease the volume Page 15 of 31 scala-rider manual DRAFT APRIL 25, 2005 6.6 Call Reject While you hear the ring tone on the headset, there are two ways you can reject the call:

- Press the CTRL button on your headset for three seconds to reject the call (FIG. 9).

- Assuming the VR feature is enabled (see section 7 below), remain silent for 7 seconds to reject the incoming call. FIG. 9 Tap here to reject the call Voice Recognition feature The VR feature allows you to answer or reject the call without removing your hands from the handlebars. The default mode of this feature is OFF To activate the VR feature please refer to section 7.1 below. FIG.10 Press the Volume Up and Volume Down buttons simultaneously for 3 seconds to activate / deactivate the VR feature. You will hear a brief tone confirming the change each time you switch ON/OFF modes. Press both buttons for 3 seconds to enable/disable the VR feature 7.1 Enable/Disable the Voice Recognition feature 7 Page 16 of 31 scala-rider manual DRAFT APRIL 25, 2005 7.2 Answering calls using Voice Recognition When hearing the ring tone of an incoming call through the headset speaker, you have 7 seconds available to utter any word of your choice in order to accept the call. 7.3 Rejecting calls using Voice Recognition When hearing the ring tone of an incoming call through the headset speaker, remain silent during the next 7 seconds in order to reject the call and cause the ringing the cease. Operating the Radio 8 The scala-rider enables you to listen to FM radio while you do not use the headset for a phone conversation. While listening to the radio, you do not have to worry about missing phone calls, as the scala-rider automatically switches to Bluetooth headset operation when the phone rings or when you decide to initiate a call. When the conversation is over, the scala-rider automatically returns to radio mode. 8.1 Turning the radio on/off 8.1.1 Turn the radio on While no call is on the headset, press and hold the Radio button on your headset for three seconds to turn on the radio. The radio turn on set to the last radio station you were listening to. 8.1.2 Turn the radio off While the radio is turned on and no call is in progress, press and hold the Radio button for three seconds to turn the radio off. 8.2 Switching preset radio station There are 6 pre-set radio stations available on your headset. While the radio is on, tap the Radio button to cycle between saved stations. 8.3 Searching for and saving a new radio station Page 17 of 31 scala-rider manual DRAFT APRIL 25, 2005 8.3.1 Enter search mode While the radio is on, press and hold for 3 seconds the Volume Up or Volume Down button on your headset to start searching. Pressing Volume Up will search upwards (higher frequency) and pressing Volume Down will search downwards (lower frequency). Once the radio finds a station it will stop and you will be able to hear this station. To save this station refer to section 8.3.2. To continue searching, press the Volume Up/Volume Down again for three seconds. Within 20 seconds of finding a station, if you dont save the station and dont search for another station the radio will exit search mode without saving the current station. You can still continue listen to the current unsaved station. Pressing the Radio button in this case will move to the next saved station. Before searching for a station to save, tap the Radio button until you find the station you want to replace. When you find a radio station you want to save by searching as describes in section [8.3.1, tap the Radio button to save the current station. 8.3.2 Saving radio station Page 18 of 31 scala-rider manual DRAFT APRIL 25, 2005 Operating the remote control 9 The remote control has two buttons which can be easily operated by a short movement of the left hand finger. 1. CTRL_RC. 2. Radio_RC. 9.1 CTRL_RC button usage 9.1.1 Power Off CTRL_RC-

Accept/ terminate calls Voice dial Radio_RC-

Radio ON/OFF Changing radio stations While your phone is ON but no call is in progress, press the CTRL_RC button for 3 seconds. You will hear a descending tone as the headset turns OFF. This will turn off the headset and the radio. In order to turn ON the headset you must use the CTRL button on the headset itself. While your phone is ON but no call is in progress, tap the CTRL_RC button. Wait for a sound and speak the name of the party you wish to call and wait for feedback from the phone. The type of feedback depends on your phone. 9.1.2 Initiate voice dial 9.1.3 Answering Calls When you hear the ring tone either on the headset or on the phone, tap the CTRL_RC to answer the call. 9.1.4 Terminating Calls To terminate a call, tap the CTRL_RC button, followed by a tone, which confirms the termination. Wait at least three seconds before pressing again the CTRL button to activate voice dial. 9.1.5 Rejecting Calls Page 19 of 31 scala-rider manual DRAFT APRIL 25, 2005 When you hear the ring tone on the headset, press and hold CTRL_RC for three seconds on your remote control to reject the call. 9.2 Radio_RC button usage 9.2.1 Power ON/OFF While no call on headset, press and hold the Radio_RC for three seconds to turn the radio ON or OFF. 9.2.2 Change radio station Tap the Radio_RC button to change the radio station to the next saved station. 9.2.3 Search radio station Searching is not possible using the Remote Control. Use the headset Radio button perform search. 9.3 Remote control functionality table Feature Headset buttons Remote control buttons CTRL (six seconds) CTRL (three seconds) Headset status Power on Off Power off On Voice dial Standby CTRL (short) Answer calls Standby CTRL (short) Terminate CTRL (short) calls Reject calls Ringing CTRL (three seconds) CTRL_RC (three seconds) Radio on/off Standby Radio (three seconds) Radio_RC (Three seconds) Change radio station CTRL_RC (short) CTRL_RC (short) CTRL_RC (three seconds) Radio on Radio (short) Radio_RC (Short) On call Page 20 of 31 scala-rider manual DRAFT APRIL 25, 2005 Status headset being turned on headset being turned off STANDBY:

Not on a call ACTIVE:

On a call or initiating a connection. PAIRING MODE Low battery while in STANDBY Low battery while a call in progress CHARGING FULLY CHARGED Toggle VR feature (On/Off) 10 Light and Sound Signals LED indication Triple blue flash Triple red flash Single blue flash every 3 seconds Double blue flash every 3 seconds Audio Feedback ascending tone (low-high) descending tone (high-low) Low bat beep Low bat beep High Tone Rapid red-blue alternating flash Single red flash every 3 seconds Double red flash every 3 seconds Steady red Steady red turns off None 11 FAQs Page 21 of 31 scala-rider manual DRAFT APRIL 25, 2005 What is the Cardo scala-rider headset?

The scala-rider wireless Headset is a comfortable, stylish and easy to use accessory to a Bluetooth mobile phone or smart-PDA when traveling on a motorcycle that enables you to hear and speak without holding your mobile phone near to your ear. Do I need an Adapter if I already have a Bluetooth enabled cell phone?

No. Your scala-rider device communicates with virtually every Bluetooth phone. How does the scala-rider Headset work?

Once, the scala-rider Headset is paired to your Bluetooth enabled mobile phone, the two devices communicate wirelessly using Bluetooth technology. If I want to keep my non-Bluetooth mobile phone, can I still use the scala-rider with my mobile phone?

You can hold on to your non-Bluetooth mobile phone and still enjoy the benefits of the Headset, if you also purchase the scala Bluetooth Adapter. The BT Adapter plugs directly into the headset jack of most non-

Bluetooth phones, thereby enabling that phone to communicate wirelessly with your headset. Is the battery removable?

The battery is not removable and you should never try to open the Headset. Let only Authorized Service Centers maintain or service your device. Please refer to our website for instructions at the end of your battery life. What if have trouble hearing?

The scala-rider headset comes with volume control, adjustable to suit your preferred volume level. What if I need more help?

Please access our website at:www.cardowireless.com/

Do I need to turn my headset off or leave it on when it is recharging?

Your headset may stay on or off during the charging process, according to Page 22 of 31 scala-rider manual DRAFT APRIL 25, 2005 your preference. When I turn on my cell phone, do I need to pair or link my cell phone and headset again?

Once your mobile phone and headset are paired, you will not have to pair it again. You will only need to implement the simple steps of reconnecting your phone and headset each time either or both are turned off or have moved more than approximately 30 feet (10 meters) apart from each other. Please refer to section 5.4 for further details. Will other Bluetooth phones interfere with my scala-rider headset?

Can they eavesdrop?

No. Once you are paired, your identity is known only to the mobile phone you use and no other Bluetooth phone can hear your audio signals. Can the headset cause interference with my car radio?

No, the Bluetooth standard does not interfere with car radios. Can I wear scala-rider in the rain?

Yes, the scala-rider is waterproof. 12 Limited warranty Page 23 of 31 scala-rider manual DRAFT APRIL 25, 2005 Your scala-rider headset is covered with a One-Year Limited product warranty from the date of original purchase. Please retain the retail sales receipt and your registration data for proof of purchase. What this limited warranty covers and for how long Cardo Systems, Inc. (the Company or Cardo) warrants the scala-rider headset and charger against defects in material and workmanship under normal use and service for a period of one (1) year from date of purchase

(proof of purchase and registration required). The Company at its sole discretion, will at no charge either repair, replace or refund the purchase price of the product to the original purchaser during the warranty period, provided the product has not been damaged or tampered with and has been returned in accordance with the terms of this warranty to an authorized Company Repair Center. Repair, at the Companys option, may include the replacement of parts, boards or batteries with functionally equivalent reconditioned or new parts. Warranty Conditions This express limited warranty is extended by Cardo Systems, Inc. solely to the original purchaser and is not assignable or transferable to others. This is the complete warranty for your scala-rider headset and charger. The Company assumes no obligation or liability for additions or modifications to this warranty unless made in writing and signed by an officer of the company. Batteries are warranted only if the battery capacity falls below 70% of rated capacity or if the battery develops leakage. This warranty becomes void if:

a. any of the seals on the case or battery are broken or device or battery show signs of tampering. b. The battery is used in equipment other than the equipment for which it was intended. The Company disclaims all responsibility for any equipment not furnished by Cardo Systems Inc., which is attached to or used in connection with the scala-rider headset. Furthermore, the Company is not responsible for any damage to any part of the scala-rider headset resulting from the use of ancillary equipment not furnished by the Company for use with the Product. What this warranty does not cover 1. Defects or damage resulting from the use of this product in other than Page 24 of 31 scala-rider manual DRAFT APRIL 25, 2005 its normal and customary manner. 2. Defects or damage from misuse, accident or neglect. 3. Defects caused by improper operation, maintenance, installation, adjustment or modification of any kind. 4. Products opened, disassembled or repaired non-authorized parties. 5. Defects or damage due to exposure to excessive temperatures, adverse weather conditions, external impacts or spills of solid or liquid substances. 6. All plastic surfaces and all other externally exposed parts that are scratched or damaged after purchase. Warranty Service To receive warranty service, your product must be registered. Fax the attached registration card to the numbers listed on the card, or register online at: http://www.cardowireless.com/registration.php For services, please present the product, along with your registration number, bill of sale (receipt) at any authorized Service Center or at the store from which you have purchased the product. Returns to the Company pursuant to the limited warranty can only be accepted with a Return Authorization number obtained from Cardos customer service department. General Provisions This warranty is given in lieu of all other express or implied warranties, including without limitation, implied warranties of merchantability and fitness for a particular purpose. Cardos obligations under this section are limited to the duration of this limited warranty. a. Certain limited-life components that are subject to normal wear and tear, such as eyeglass clips, ear clips, decorative finishes, batteries, panels, cradles, or other accessories, are exempt from any warranty. Page 25 of 31 scala-rider manual DRAFT APRIL 25, 2005 b. Cardo is not liable for any incidental or consequential damages arising from the use or misuse of any of the Companys products. c. The user should never attempt to perform service, adjustments or repairs of the Product by him/herself. Doing so will void all warranties. During the term of the warranty, all products must be returned to the point of purchase or the authorized service center for all necessary work. d. The Company is not responsible for any loss or damage incurred during shipping. All repair work on scala-rider products by parties not explicitly authorized by the Company will void any and all warranties. e. The information in this Manual is furnished strictly for informational purposes and is subject to change without notice. Cardo assumes no liability or responsibility for any errors or inaccuracies that may appear in this Manual or the Quick Guide. NOTE: Look for appropriate displays to verify that you are being serviced by an Authorized Cardo Dealer or Service Center. Cardo Systems, Inc. retains the right to amend and change its products, manuals and specifications at any time without notice. Page 26 of 31 scala-rider manual DRAFT APRIL 25, 2005 g 13 Troubleshooting Problem Pairing fails Action:

1. Delete scala-rider from your paired device list in your phone (if it is listed) 2. Turn off the mobile phone and headset 3. Take out the battery of the phone (some phones have shown problems with pairing that are solved only if the battery is temporarily unplugged) 4. Repeat the pairing process as shown in section 5.2. Problem Cant answer phone calls or perform voice dialing Action (assuming your mobile phone supports this feature) 1. Make sure your scala-rider headset is turned ON and in standby mode while the blue light indicator flashes slowly. 2. Verify that the Bluetooth function on your phone is set to ON. 3. Verify that the scala-rider headset is the correctly paired Headset to your mobile phone

(refer to phone manual) 4. Link the headset to the phone as described above 5. Check Definitions or Settings on your mobile phone. 6. Perform pairing process and check again. Problem Battery does not provide at least five hours talk time. Action Make sure your scala-rider Headset is fully charged. Charging time is up to 6 hours for an empty battery. When fully charged and charger is connected to Headset, the red light indicator turns off. Page 27 of 31 scala-rider manual DRAFT APRIL 25, 2005 Problem Red LED does not light steady when charger is connected. Action 1. Make sure DC jack is firmly plugged in 2. Disconnect DC jack, wait a few seconds and plug it back in. 3. If the scala-rider Headset is fully charged the red light turns off. Problem Bad sound quality Action 1. Possibly caused by nearby interference 2. If you have a GSM phone and your headset is to close to phone, noises may be heard 3. Headset and mobile phone are more than 30ft (10m) apart or there are major obstacles between headset and mobile phone (e.g. concrete walls or similar). Problem Sound deteriorates when the phone is in my back pocket. Action Some mobile phones emit weaker Bluetooth signals than others, resulting in reduced sound quality, especially when the phone is close to your body. Suggestion: Move the phone to your breast pocket or at least to a front pocket on the same side you wear your headset. Page 28 of 31 scala-rider manual DRAFT APRIL 25, 2005 14 FCC notice This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the Users authority to operate the equipment. Use only approved batteries and chargers. This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Your scala-rider headset is designed to operate at the maximum strength allowed by the FCC. This means that your headset and or base unit can communicate only over a certain distance subject on the location of the cell phone, base unit and headset, your vehicle, the construction and layout of your home or office. Weather conditions can also affect performance. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Tech Specs and Regulations 15 Technical Specification Technology:

Maximum power:

Maximum link distance: 30 feet or 10 meters Typical talk time:

Typical standby time:

Typical charging time: 6 hours Power Source:

Weight:

Approvals:

Wind blocking:

Note: Design and specifications are subject to change without notice. Your rated standby-time is subject to the amount of talk-time used. Rechargeable Lithium Polymer battery 1.12 oz or 33 g (without the clamp). FCC Part 15, CE, Bluetooth Compliant with Bluetooth ver 1.1 / 1.2 2.5 dbm up to 6 hours up to 6 days Up to 16km/h (10miles/h) Page 29 of 31 scala-rider manual DRAFT APRIL 25, 2005 ALERTE Risque d'explosion si la batterie est remplace par un model qui ne convient pas. Il faut traiter les batteries uses selon les instructions. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. 16 European CE Notice Certification and Safety Approvals/ General Information This product is CE marked according to the provisions of the R & TTE Directive (99/5/EC). Hereby Cardo Systems, Inc. declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. For further information please visit http://www.cardowireless.com Please note that this product uses radio frequency bands not harmonized within the European Union (EU). Within the EU this product is intended to be used in Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, The Netherlands, Portugal, Spain, Sweden, The United Kingdom and within EFTA in Iceland, Norway and Switzerland. Users are not permitted to make changes or modify the device in any way. Changes or modifications not expressly approved by Cardo will void the users authority to operate the equipment. Regulations and Notices Page 30 of 31 scala-rider manual DRAFT APRIL 25, 2005 17 Contact Information Cardo Systems, Inc., 100 High Tower Blvd., Pittsburgh, PA. 15205 (USA) North America: Call toll-free: 1 800 488-0363 or 412 788-4533, Fax: 412 788-0270 International: Call +49 89 450 36-819, Fax: +49 89 404-817 18 Service North America: Call toll-free: 1 800 488-0363 or 412 788-4533 International: Call +49 89 450 36-819 Service is provided under limited warranty. Cardo Systems, Inc. will only accept devices returned in compliance with our Warranty Provisions and submitted with a Return Authorization Number issued by a Cardo authorized service department. The Company retains the right to return all shipments not in compliance with our Warranty Provisions. 19 Patent, Copyright, Trademark Information U.S. and Worldwide Patent Pending;

2004 Cardo Systems Inc. Assembled in China. Bluetooth is a trademark owned by Bluetooth SIG, Inc., scala-rider is a trademark owned by Cardo Systems, Inc. All rights reserved by Cardo Systems, Inc. Page 31 of 31