CARDOSYSTEMS,INC. User Guide Gebrauchsanleitung Guide dUtilisation Guida di Avvio Guia de Usario
| Cardo Rider Q2
| INTRODUCTION | CONTENTS OF RETAIL BOX INTRODUCTION Congratulations, and thank you for having chosen the Cardo Rider Q2 Bluetooth Headset for bikers. This Manual will help you operate the headset, but you should first familiarize yourself with the Bluetooth functionality of your cellular phone and/or GPS device before using the Cardo Rider Q2. The retail box of the Cardo Rider Q2 contains one headset unit. When paired with another Cardo Rider Q2, the headsets can be used as an Intercom at a range of up to 600 ft (200m). The Cardo Rider Q2 offers the following uses:
1. Bluetooth headset for mobile phone communication, supporting headset* and Handsfree* profiles (10m range) 2. Bike-to-Bike Intercom Communication with another Q2 unit
(up to 600 ft. / 200m range) in Full Duplex** mode [purchased separately]
3. Turn-by-Turn GPS Navigation instructions and Streaming Audio from compatible Bluetooth devices 4. FM Radio built in FM radio receiver with six preset stations The Cardo Rider Q2 can establish an audio connection with one Bluetooth device at a time. Please read the section Using the Headset to see how you can switch the audio connection between the paired devices. CONTENTS OF RETAIL BOX Headset Volume Up Charging Jack Volume Down CTRL Control Button Power On, Power O Answer/End MC Multi-Connection Radio On/O/change stations Initiate/Terminate Buddy Intercom call with Primary or Secondary Buddy Helmet Clamp Right Speaker
(long cord) Tab Sliding Plate Microphone Left Speaker
(short cord) ____________________
* Mobile phones that do not support the Bluetooth Handsfree prole may prevent you from using the Redial and Call Reject features
** Full duplex calls allow you to speak and hear the other party speak simultaneously NOTE: The use of two speakers may be illegal in certain jurisdictions. Please check the local regulations and act accordingly. 2 CONTENTS OF RETAIL BOX | BEFORE USING |
Cardo Rider Q2 |
Wall Charger Allen Wrench Velcro Pads Extension Pad User Guide, including Warranty and Registration form IMPORTANT:
The Cardo Rider Q2 is a water-resistant device, designed for use under moderate rain or snow conditions. However, the headset is not waterproof and should not be used under severe weather conditions. The cover tongue protecting the Charging Jack should be kept tightly closed at all times to prevent moisture from entering the device. BEFORE USING (CHARGING THE HEADSET) Make sure that the headset is fully charged for at least five hours before initial use. 1. Connect the wall charger to the headsets Charging Jack
(located between the two Volume Buttons). 2. While charging, the Red Light turns on (it may take up to 15 seconds until the Red Light turns on). When charging is complete, the Red Light will turn off. E n g l i s h SET UP AND CONFIGURATION Full Duplex Intercom Connection Cardo Rider Q2 or scala-rider Family Headset Embedded Embedded FM Radio FM Radio 200 meters 200 meters
(600 ft.)
(600 ft.) Mobile Phone GPS STEP 1 SET UP FOR BIKE-TO-BIKE INTERCOM: PAIRING The Cardo Rider Q2 can be paired with up to two other headsets for Intercom communication, referred to in this guide as:
Primary Buddy and Secondary Buddy. Pairing is a one time process. Once the headsets are paired during this Setup Procedure, they will remain paired and automatically recognize each other whenever they are within range. NOTE: The Cardo Rider Q2 allows you to speak via Intercom to one Buddy headset at a time. 3
| Cardo Rider Q2
| SETUP AND CONFIGURATION PRIMARY BUDDY PAIRING (requires two Cardo Rider Q2 headsets) 1. If either headset is turned OFF, turn it ON by pressing and holding the CTRL Button until the Blue Light flashes three times. 2. Make sure that both headsets are now flashing slowly in Blue. 3. Pick up one headset and simultaneously press and hold the CTRL Button and MC Button for at least six seconds until the Red Light begins flashing rapidly, indicating it is in Intercom Pairing mode. 4. Repeat Step 3 again for the second Cardo Rider Q2 headset. Both headsets should now be flashing rapidly in Red. 5. Within a few seconds, both headsets will show a solid Red light for two seconds, and then begin flashing slowly in Blue. SECONDARY BUDDY PAIRING (requires three Cardo Rider Q2 headsets) Once you have paired the Main Cardo Rider Q2 to the Primary Buddy headset, repeat the procedure above to pair the Main Cardo Rider Q2 to the Secondary Buddy headset. NOTE: The Main Cardo Rider Q2 is able to communicate with either the Primary Buddy or the Secondary Buddy. The Primary Buddy and Secondary Buddy are not able to communicate directly via Intercom. NOTE: If the Pairing process is not completed within one minute the headset will return to Standby mode. STEP 2 (Optional) SET UP FOR RIDER-TO-PASSENGER INTERCOM: PAIRING There are two ways that the Cardo Rider Q2 can be used for Rider-to-
Passenger communication.
A. Both Rider and Passenger are using Cardo Rider Q2 headsets. To Pair the two headsets, follow the Steps listed in the section above titled PRIMARY BUDDY PAIRING. B. The Rider is using a Cardo Rider Q2 and the Passenger is using a scala-rider headset (i.e. a scala-rider, a scala-rider FM or a scala-
rider TeamSet Driver unit headset). To Pair the two headsets:
1. Starting with the scala-rider headset turned OFF, press and hold the CTRL button until the Red/Blue lights begin rapidly alternating. 2. Starting with the Cardo Rider Q2 turned ON, simultaneously press and hold the CTRL Button and MC Button for six seconds until the Red light begins flashing rapidly, indicating it is in Intercom Pairing mode. 3. Within a few seconds, the Cardo Rider Q2 will show a solid Red light for two seconds, and then begin flashing slowly in Blue. NOTE: If the Pairing process is not completed within one minute the headset will return to Standby mode. NOTE: When using a scala-rider headset as a Passenger headset, Voice Connect Intercom can be initiated only by the Cardo Rider Q2 headset. Manual Connect Intercom can be initiated from either headset. RESET INTERCOM PAIRING You can delete all of the headsets Intercom pairings at any time. 1. Place the Cardo Rider Q2 into Intercom Pairing mode following the instructions in the PRIMARY BUDDY PAIRING section above. 2. Once the Red Light begins flashing rapidly, press and hold Volume up for three seconds. 3. The Red and Blue Lights will flash five times, confirming that the Reset Pairing was successful. E n g l i s h SETUP AND CONFIGURATION |
Cardo Rider Q2 |
STEP 3 SET UP FOR MOBILE PHONE CALLS: PAIRING If you have a Bluetooth enabled mobile phone and would like to make and receive phone calls using the Cardo Rider Q2, you must first pair your headset to the mobile phone. NOTE: If you have a compatible Bluetooth GPS device you wish to use with the Cardo Rider Q2, please skip this step, and continue ahead to STEP 4: SET UP FOR BLUETOOTH GPS DEVICE. Pairing is a one time process. Once the headset is paired to a specific mobile phone during this Setup Procedure, they will remain paired and automatically recognize each other whenever they are within range. If the connection between the phone and headset is lost, tap the CTRL button to reconnect the devices. TO PAIR THE CARDO RIDER Q2 TO A BLUETOOTH MOBILE PHONE 1. Turn on your phone and make sure its Bluetooth function is activated. 2. With the Cardo Rider Q2 headset turned ON, press and hold the CTRL Button for at least six seconds until the Red and Blue Lights begin rapidly alternating. 3. Search for Bluetooth devices on your phone by following the phones instructions. Please consult your phones User Manual for more information. 4. After a few seconds the phone will list the Cardo Rider Q2 as a discovered device. Select it and follow your phones instructions to accept the pairing. 5. When prompted enter 0000 (four zeros) as your PIN or passkey. 6. Your phone will confirm that pairing has succeeded and the headset will begin flashing slowly in Blue. NOTE: If the Pairing process is not completed within two minutes the headset will return to Standby mode. With some mobile phones, you may need to tap the CTRL button to connect the headset to the phone after pairing is complete. The Cardo Rider Q2 headset will automatically connect to the last phone connected to the headset. STEP 4 SET UP FOR BLUETOOTH GPS DEVICE: PAIRING If you have a Bluetooth enabled GPS device and would like to transmit navigation instructions and sounds from the GPS device through the headsets speakers, you must first pair your headset to the GPS device. NOTE: Not all Bluetooth enabled GPS devices allow connections to Bluetooth headsets like the Cardo Rider Q2. Please consult your GPS devices User Manual for more information. TO PAIR THE CARDO RIDER Q2 TO A BLUETOOTH GPS DEVICE:
1. Turn on your GPS device. 2. With the Cardo Rider Q2 headset turned ON, press and hold the CTRL Button for at least six seconds until the Red and Blue Lights begin rapidly alternating. 3. Search for Bluetooth headsets on your GPS device by following the devices instructions. Please consult your GPS devices User Manual for more information. 4. If your GPS device prompts for a PIN or Passkey enter 0000 (four zeros). 5. Your GPS device will confirm that pairing has succeeded. The headset will begin flashing slowly in Blue. 6. If you wish to use a Bluetooth mobile phone to make and receive calls through the headset, you must now pair your
| Cardo Rider Q2
| SETUP AND CONFIGURATION mobile phone to your GPS device by following your GPS and/or mobile phones instructions. NOTE: If the Pairing process is not completed within two minutes the headset will return to Standby mode. MOUNTING THE HEADSET ON THE HELMET The microphone/speaker clamp must be mounted onto the helmet. Once mounted, the headset unit can be attached or detached from the microphone/speaker clamp at any time. Allen Wrench Back Plate Attaching the Clamp to the Helmet 1. Use the enclosed Allen Wrench to loosen the two screws on the Back Plate. 2. Slide the Back Plate between the internal padding and the external shell of the helmet. (If the external shell is too thick, use the supplied plastic Extension Pad by loosening the screws and fitting the Extension Pad between the Back Plate and the main body of the clamp.) 3. Adjust the clamps location so that the microphone is located in front of the center of your mouth, with the yellow sticker pointing towards your mouth, and then tighten the screws. CORRECT INCORRECT ATTACHING AND REMOVING THE HEADSET FROM THE HELMET CLAMP ATTACHING:
Slide the headset downwards along the sliding panel until a clicking sound indicates that the headset is locked in place. 6 REMOVING:
Press here to remove Your headset can be removed for charging and storage by pressing your finger gently against the tab and sliding the headset up with the other hand. We recommend that you remove the headset from the helmet when not in use. SPEAKERS AND MICROPHONE POSITIONING The microphone must be positioned vertically, not horizontally, in front of the center of the mouth, with the yellow sticker pointing towards the mouth. Attach the speakers to the Velcro inside your helmet opposite your ears
(short speaker cord for left ear & long speaker cord for right ear), or use the supplied Velcro pads. USING THE HEADSET GENERAL USAGE DESIRED RESULT:
Turn on the headset Turn off the headset Increase the volume Decrease the volume GENERAL FUNCTIONS REQUIRED ACTION:
Press the CTRL Button steadily for at least three seconds Press the CTRL Button steadily for at least three seconds Short press the Volume Up Button Short press the Volume Down Button AGC (Automatic Gain Control): In addition to manual Volume Control, the Cardo Rider Q2 will automatically increase and reduce its volume according to ambient noise and driving speed. SETUP AND CONFIGURATION |
Cardo Rider Q2 |
AUDIO SOURCES AND PRIORITIES The different Audio Sources that are connected to the Cardo Rider Q2 are prioritized as follows:
Highest 1. Mobile phone Audio / GPS device (Incoming/outgoing calls , GPS audio and navigation instructions) 2. Primary Buddy Audio and Secondary Buddy Audio Lowest 3. FM Radio A high priority Audio Source will always interrupt any lower priority Audio Source. USING THE INTERCOM Making Intercom calls Mobile phone call interrupts Intercom call Intercom call interrupts FM Radio i.e. To start a Buddy Intercom call with the Primary Buddy while the headset is on Standby you can either:
or VOICE CONNECT:
Start talking A Buddy Intercom call will be established and stay on until both sides are quiet for 30 seconds. MC BUTTON CONNECT:
Single tap the MC Button A Buddy Intercom call will be established. To end the Buddy Intercom call, single tap the MC Button again. To start a Buddy Intercom call with the Secondary Buddy while the headset is on Standby:
MC BUTTON CONNECT:
Double tap the MC Button A Buddy Intercom call will be established. To end the Buddy Intercom call, double tap the MC Button again. MC Button 7 E n g l i s h NOTE: When using a scala-rider Headset as a Passenger headset, Voice Connect Intercom can be initiated only by the Cardo Rider Q2 headset. Manual Connect Intercom can be initiated from either headset. Failed Connection: On the Cardo Rider Q2, if you attempt to start a Buddy Intercom call with a Buddy that is already on a Phone/GPS/
Intercom call, you will hear a double beep indicating the Buddy is busy. Reconnecting the Intercom: If the Cardo Rider Q2 and its Intercom Buddy headset go out of range and disconnect from each other, the Cardo Rider Q2 will automatically try to reconnect to its Intercom Buddy for five minutes. You can manually reconnect at any time by pressing the MC Button
(single tap for Primary Buddy and double tap for Secondary Buddy). Receiving Intercom calls If you are not speaking with any one, once the other party tries to initiate a Buddy Intercom call, the call will begin immediately. TROUBLESHOOTING THE INTERCOM:
First, make sure your microphone is located properly in front of the center of your mouth. The Cardo Rider Q2 is designed for use in loud environments. Please make sure to test the Intercom functionality in a LOUD environment, such as next to an idling motorcycle. Please also verify that the headsets were paired together properly by following the instructions in the relevant Setup sections. Setting Voice Connect Intercom preference (Primary vs. Secondary Buddy) The headsets Voice Connect feature allows you to start a Buddy Intercom call by simply speaking into the microphone. You can define
| Cardo Rider Q2
| SETUP AND CONFIGURATION which of the two Buddy headsets you wish to connect to when using Voice Connect Intercom. NOTE: The Primary Buddy has priority by default. To toggle the Voice Connect Intercom between Primary and Secondary Buddy:
When the headset is on an active phone call, any Buddy Intercom call request will be rejected automatically. Once the phone call audio link drops, you can initiate and accept Buddy Intercom calls. STATUS LIGHT STATES Press and hold the Volume Up Button for three seconds and you will hear a beep:
One beep Voice Connect set to Primary Buddy Two beeps Voice Connect set to Secondary Buddy Enable/Disable Voice Connect feature Press and hold the Volume Up and Down Buttons simultaneously until you hear a beep. The default status is Voice Connect enabled. NOTE: The Enable/Disable Voice Connect feature affects both the Intercom and the mobile phone functionality. MAKING AND RECEIVING MOBILE PHONE CALLS Answer a call Reject a call Terminate a call Voice Dial Redial PHONE FUNCTIONS Short press the CTRL Button or speak loudly any word of your choice. Short press the MC Button or remain silent for 15 seconds. Short press the CTRL Button. During Standby, short press the CTRL Button and state the name of the person you wish to call. This feature is supported only by mobile phones that support the Voice Dial feature. Press and hold the Volume Down Button for three seconds. NOTE: If your Bluetooth mobile phone is paired to a Bluetooth GPS device, not directly to the Cardo Rider Q2, some of the above Phone functions may not be compatible. Headset is off None Alternating Red/blue flashes Mobile phone/GPS Pairing mode Rapid Red flashes 1 blue flash every 3 seconds 2 blue flashes every 3 seconds Call being initiated or in progress /
Intercom Pairing mode Standby No call is in progress 1 red flash every 3 seconds 2 red flashes every 3 seconds Call being initiated or in progress /
FM Radio ON Battery is low Solid red FM Radio ON and battery is low Headset is being charged WORKING WITH THE FM RADIO Your headset is equipped with a high-quality FM Radio receiver. This section explains how to enjoy the functions of the FM Radio. The Cardo Rider Q2 enables you to listen to FM Radio while you are not receiving audio from another audio source. While listening to the radio, you do not have to worry about missing any calls, as the headset automatically mutes the FM Radio and switches to Bluetooth headset operation when an incoming call is received, or when you decide to initiate a call. When the conversation is over, the headset automatically tunes back in to the FM Radio. Turning the FM Radio On While no call is on the headset (either mobile phone call or Intercom call), press and hold the MC Button on your headset for three seconds to turn
SETUP AND CONFIGURATION | SUPPORT | NOTICES Cardo Rider Q2 |
on the radio. The radio tunes in to the last radio station you were listening to. With some phones you should wait a few seconds after ending a call before turning on the Radio. Turning the FM Radio Off While the radio is turned on, press and hold the MC button for three seconds to turn the Radio off. Switching Preset FM Radio Station There are six pre-set Radio stations available on your Cardo Rider Q2. While the Radio is on, tap the MC Button to cycle between saved stations. Searching for a New FM Radio Station While the Radio is on, press and hold the Volume Up or Volume Down Button for three seconds or until you hear the next station on your headset. Pressing Volume Up will search upwards (higher frequency). Pressing Volume Down will search downwards (lower frequency). Once a station is found, searching stops and you can hear the station. To save this station, refer to the following section. To continue searching, press the Volume Up or Volume Down Button again for three seconds. You may still continue to listen to the current unsaved station. Pressing the MC Button in this case will switch to the next saved station. Saving an FM Radio Station The FM Radio is equipped with a memory capacity of six stations. Select the station you wish to replace by tapping the MC button until you find the station you want to replace. Search for a new station as described above. Tap the MC Button within 20 seconds of finding the station to save the current station. If you don't save the station, the Radio will exit search mode without saving the current station. You can still continue to listen to the current unsaved station. Tapping the MC Button in this case will move to the next saved station. E n g l i s h SUPPORT For additional information please visit our website at www.cardosystems.com FAQ: www.cardosystems.com/faq or contact us at:
support@cardosystems.com Phone:
USA and Canada + 1-800-488-0363 International +4989 450 36819 NOTICES FCC Notice ThisequipmentcomplieswithPart15oftheFCCRules.Operationis subjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseharmful interference,and(2)thisdevicemustacceptanyinterferencereceived, includinginterferencethatmaycauseundesiredoperation. FCC RF Radiation Exposure Statement:
ThisequipmentcomplieswithFCCradiationexposurelimitssetforthfor an uncontrolled environment. End users must follow the specific operating instructionsforsatisfyingRFexposurecompliance.Thistransmittermustnotbe co-locatedoroperatinginconjunctionwithanyotherantennaortransmitter.
| Cardo Rider Q2
| NOTICES Warning: Changes or modifications to this unit not expressly approved bythepartyresponsibleforcompliancecouldvoidtheusersauthorityto operatetheequipment.Useonlyapprovedbatteriesandchargers.This equipmenthasbeentestedandfoundtocomplywithPart15oftheFCC rules.Theselimitsaredesignedtoprovidereasonableprotectionagainst harmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates andcanradiateradiofrequencyenergy,andifnotinstalledandusedin accordancewiththeinstructions,maycauseharmfulinterferencetoradio communications.However,thereisnoguaranteethatinterferencewill notoccurinaparticularinstallation.YourCardoRiderQ2headsetis designedtooperateatthemaximumstrengthallowedbytheFCC.This meansthatyourheadsetcancommunicateonlyoveracertaindistance subjectonthelocationofthecellphone,baseunitandheadset,your vehicle, the construction and layout of your home or office. Weather conditionscanalsoaffectperformance. CAUTION NEVER OPEN THE HEADSET AS THIS MAY CAUSE DAMAGE OR INJURY AND WILL VOID YOUR WARRANTY. NOTE:Ifthisequipmentcausesharmfulinterferencetoradioortelevision reception,whichcanbedeterminedbyturningtheequipmentoffandon,the userisencouragedtotrytocorrecttheinterferencebyoneormoreofthe followingmeasures:
Reorientorrelocatethereceivingantenna. Increasetheseparationbetweenequipmentandreceiver. Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhich thereceiverisconnected. Consultthedealeroranexperiencedradio/TVtechnicianforhelp. European CE Notice TheCardoRiderQ2headset(theProduct)isinconformitywiththe followingessentialrequirementsofCouncilDirective1999/5/EC(referredto asR&TTEDirective):Articles3.1a,3.1.band3.2.TheProductismanufactured inaccordancewithAnnexIIoftheabovedirective. Declaration of Conformity (DOC) TheCardoRiderQ2headsetiscompliantwithandadoptstheBluetooth Specification 2.0 and has successfully passed all interoperability tests that are specified in the Bluetooth specification. However, interoperability betweenthedeviceandotherBluetooth-enabledproductsisnotguaranteed. WAIVER AND GENERAL RELEASE By using the Cardo Rider Q2 you will waive substantial legal rights incc cluding the right to sue. Please read the following carefully before using the device. If you do not accept all terms of this agreement, you should immediately return the product for a full refund. By using the headset you agree to be bound to this agreement and forfeit the right to sue. Usingacommunicationdevicewhileridingamotorcycle,scooter,moped,ATV, quad-bike or any other vehicle or equipment, whether on land, water or air
(jointlyreferredtoasVehicle)requiresyourcompleteandundividedattention. Cardo Systems, Inc., including its Officers, Directors, Affiliates, Parent Comp-
pany,Representatives,Agents,Contractors,Sponsors,Employees,Suppliers andResellers(jointlyreferredtoastheCompanyorCardo)stronglyadvises you to take all necessary precautions and remain alert to the traffic, weather androadconditionsifyouchoosetousetheCardoRiderQ2headset,includ--
ingallderivativemodelsirrespectiveofitscommercialnameorbranding(the Device),andstopyourVehicleontheroadsidepriortoinitiatingorreceiving calls.Anypublications,advertisements,announcementsorsimilarnotesthat refertousingtheDevicewhileridingaVehiclearesolelyintendedtoaddressits technicalcapabilitiesandshouldnotbemisconstruedasifencouragingusers to operate the Device while actively involved in traffic. BywayofpurchasingthisDeviceandnotreturningitforafullrefund(seebe--
low),youareirrevocablyreleasing,indemnifyingfromanyliability,loss,claim and expense (including attorneys fees) and holding Cardo harmless for any bodilyinjuries,harmordeathaswellaslossesordamagesingoods,toany Vehicles including your own, or to any property or asset that belong to you or to third parties, any of which may result from using the Device under any circumstancesorconditionsandirrespectiveofjurisdiction.Cardowillnotbe responsible for any physical damages, irrespective of reasons, conditions or circumstances,includingmalfunctioningoftheDevice,andallrisksassociated withoperatingitrestsolelyandentirelywiththeuserofthisDevice,irrespective ofwhethertheDeviceisusedbytheoriginalpurchaseroranythirdparty. Cardo hereby notifies you that using this Device may also be in contravention 10 NOTICES |
Cardo Rider Q2 |
tolocal,federal,stateornationallawsorregulations,andthatanyuseofthe Deviceisentirelyatyoursoleriskandresponsibility. 1.You,yourheirs,legalrepresentatives,successorsorassigns,herebyvolun--
tarilyandforeverrelease,discharge,indemnifyandholdharmlessCardofrom anyandalllitigation,claims,debts,demands,actionsandliabilitywhichmay arise,directlyorindirectly,fromusingtheDeviceforanydistress,pain,suffer--
ing,discomfort,loss,injury,death,damagestoorinrespecttoanypersonor property however caused, WHETHER ARISING FROM THE NEGLIGENCE OR OTHERWISE, and which may hereafter accrue to you on some future date asaresultofsaiduse,tothefullestextentpermittedbylaw. 2.YoufullyunderstandandassumetherisksinusingtheDevice,includingrisk ofnegligentactsoromissionsbyothers. 3. You confirm that you are physically capable to use the Device and that you have no medical conditions or needs that may infringe upon your abilities to do so in a safe manner. You confirm that you are at least eighteen (18) years ofageandthatyouhavebeenadvisedoftherisksassociatedwiththeuseof the Device. You further confirm that you will not consume any alcohol that may affectyouralertnessoranymind-alteringsubstance,andwillnotcarry,useor consumethesesubstancesbeforeorduringtheuseoftheDevice. 4.Youfullyacknowledgeourwarningsandunderstandthat:(a)risksanddan--
gers exist in using the Device while in traffic, incl. but not limited to injury or illness,strains,fractures,partialand/ortotalparalysis,deathorotherailments thatcouldcauseseriousdisability;(c)theserisksanddangersmaybecaused bythenegligenceofthemanufacturersoritsagentsoranythirdpartyinvolved indesigningormanufacturingtheDevice;(d)theserisksanddangersmayarise fromforeseeableorunforeseeablecauses.Youherebyassumeallrisksand dangersandallresponsibilityforanylossesand/ordamages,whethercaused inwholeorinpartbythenegligenceorotherconductofothers,includingthe Company. 5. You confirm that you have read this release of liability and fully understand its termsandthatyouhavegivenupsubstantialrightsbynotreturningtheDevice forafullrefund(seerefundoptionbelow). Disclaimer of Warranty IMPLIED WARRANTIES CARDO DISCLAIMS ALL EXPRESS AND WITH REGARD TO THE ENCLOSED DEVICE, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NONpINFRINGEMENT. THE DEVICE AND IS AS AVAILABLE WITHOUT WARRANTY OF ANY KIND AND BEYOND THE ENCLOSED MANUAL. ITS ACCESSORIES ARE PROVIDED THOSE ASSUMED AS IN E n g l i s h Limitation of Liability IN NO EVENT SHALL CARDO BE LIABLE FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THE DEVICE, WHETHER BASED ON BREACH OF CONTRACT, TORT
(INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. YOU ACKNOWLEDGE AND AGREE THAT THE LIMITATIONS SET FORTH ABOVE ARE FUNDAMENTAL ELEMENTS OF THIS AGREEMENT AND THE DEVICE WOULD NOT BE PROVIDED TO YOU ABSENT SUCH LIMITATIONS. SOME STATE STATUTES MIGHT APPLY REGARDING LIMITATION OF LIABILITY. RETURN FOR FULL REFUND IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONcc DITIONS, YOU MAY RETURN THIS DEVICE TO CARDO FOR A FULL REFUND, PROVIDED THAT YOU DO SO NO LATER THAN 7 BUSINESS DAYS FOLLOWING THE PURCHASE OF THE DEVICE (proof of purchase required) AND SUBJECT TO THE WRAPPING BEING INTACT. WHEN DOING SO, PLEASE REFER TO THIS SECTION. BY NOT RETURNING THE DEVICE FOR REFUND WITHIN THE PERIOD PROVIDED, YOU ARE EXPLICITLY IN AGREEMENT WITH THE ABOVE, AND RENOUNCE ALL RIGHTS TO FUTURE CLAIMS AND DEMANDS AGAINST CARDO AS DEcc FINED ABOVE. 11 www.cardosystems.com
| Cardo Rider Q2
| NOTICES 12