INSTALLATION BT12 Wireless Awning Control System CONTROL SYSTEM FOR 12V MOTORIZED AWNINGS USING BLUETOOTH WIRELESS TECHNOLOGY Read this manual before installing or using this product. Failure to follow the instructions and safety precautions in this manual can result in personal injury and/or cause the product to not operate properly. The BT12 Wireless Awning Control System may be installed as part of the original motorized awning installation or as an upgrade to an existing motorized awning installation. The system offers unique features not available with a standard awning installation. 1) Carefree Connects Mobile App The app provides full and enhanced control of the awning using a smart phone or tablet. The free app can be downloaded on any devices that support: 1) Current iOS or Android operating systems, and 2) Bluetooth low energy technology. 2) Full Retract When the awning is retracted, it retracts completely. It is not necessary to hold the button when closing the awning. 3) Full Extend When the awning is extended, it extends completely. It is not necessary to hold the button when opening the awning. 4) Auto-Retract The awning can be set to automatically close when windy conditions occur with the optional BT Motion Sensor. 5) Remote Control The operator can conveniently operate the awning from any location with the optional BT Remote. 070029-001r1 Printed in USA March, 2018 INSTALLATION MANUAL CAREFREE OF COLORADO Increase the separation between the equipment and receiver. BT12 WIRELESS AWNING CONTROL SYSTEM NOTICES AND DISCLAIMERS TRADEMARKS The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. Use of such marks by Carefree of Colorado is under license. Other trademarks and trade names are those of their respective owners. STATEMENTS OF COMPLIANCE BT12 Control Module BT Motion Sensor BT Remote FCC and IC identification numbers are located on the exterior surfaces of the individual components. FCC COMPLIANCE These devices comply with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) These devices may not cause harmful interference and, (2) These devices must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. IC COMPLIANCE These devices comply with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) These devices may not cause harmful interference and, (2) These devices must accept any interference received, including interference that may cause undesired operation. Ces appareils sont conformes aux normes RSS exonres de licence d'Industrie Canada. L'opration est soumise aux deux conditions suivantes: (1) Ces appareils ne doivent pas causer d'interfrences nuisibles et, (2) Ces appareils doivent accepter toute interfrence reue, y compris les interfrences pouvant entraner un fonctionnement indsirable. FCC/IC RADIATION EXPOSURE STATEMENT BT12 Control Module BT Motion Sensor This equipment complies with FCC and IC radiation exposure limits for an uncontrolled environment. The minimum distance between the radiator and people is designed to be 20cm when installed and operated. Cet quipement est conforme aux limites d'exposition aux radiations FCC et IC pour un environnement non contrl. La distance minimale entre le radiateur et les personnes est de 20cm lorsqu'install et utilis. BT12 Remote This equipment complies with FCC and IC radiation exposure limits for an uncontrolled environment. The minimum distance between the radiator and people is designed to be 5mm when operated. Cet quipement est conforme aux limites d'exposition aux radiations FCC et IC pour un environnement non contrl. La distance minimale entre le radiateur et les personnes est de 5mm ( l'exclusion des extrmits:
mains, poignets, pieds et chevilles) lors de l'utilisation. 2 070029-001r1 INSTALLATION MANUAL BT12 WIRELESS AWNING CONTROL SYSTEM CAREFREE OF COLORADO DISCLAIMERS The BT12 Wireless Awning Control System and the Carefree Connects Mobile App are products of Carefree of Colorado, located in Broomfield, Colorado, USA. The information contained in or disclosed in this document is considered proprietary to Carefree of Colorado. Every effort has been made to ensure that the information presented in the document is accurate and complete. However, Carefree of Colorado assumes no liability for errors or for any damages that result from the use of this document. The information contained in this manual pertains to the current components and software listed on the title page. Carefree of Colorado reserves the right to cancel, change, alter or add any parts and procedures, described in this manual, without prior notice. Carefree of Colorado agrees to allow the reproduction of this document for use with Carefree of Colorado products only. Any other reproduction or translation of this document in whole or part is strictly prohibited without prior written approval from Carefree of Colorado. SERVICE AND SUPPORT www.carefreeofcolorado.com customerservice@carefreeofcolorado.com Carefree of Colorado 2145 W. 6th Ave. Broomfield, CO 80020 TABLE OF CONTENTS Installation ..................................................................................................................................... 5 BT12 Control Module Installation ............................................................................................................ 6 Awning Switch Installation ...................................................................................................................... 7 LED Switch Installation ........................................................................................................................... 7 Wiring Diagram ....................................................................................................................................... 8 Installing the BT Motion Sensor .............................................................................................................. 9 Altitude / Longitude / Latitude ......................................................................................................... 9 Small Box Awnings ......................................................................................................................... 9 Pairing the Motion Sensor .............................................................................................................. 9 Setting the System into Pairing Mode ................................................................................................... 10 Battery Replacement ................................................................................................................... 11 BT Motion Sensor ................................................................................................................................. 11 BT Remote............................................................................................................................................ 11 BT12 Wireless Awning Control Kits .......................................................................................... 12 070029-001r1 3 BT12 WIRELESS AWNING CONTROL SYSTEM SAFETY INFORMATION INSTALLATION MANUAL CAREFREE OF COLORADO This is the safety alert symbol. It is used to alert individuals to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible personal injury or death. Indicates a hazardous situation, which if not avoided, could result in death or serious bodily injury. Indicates a hazardous situation, which if not avoided, may result in minor or moderate bodily injury. Indicates a situation that may result in equipment-related damage. WARNING CAUTION NOTICE General Safety:
WARNING SHOCK HAZARD. Always disconnect battery or power source before working on or around the electrical system. WARNING Always wear appropriate safety equipment (i.e. goggles). WARNING FALL HAZARD. ALWAYS use a ladder that meets or exceeds the standards and requirements of the American National Standards Institute and the Occupational Safety and Health Administration. ALWAYS follow the manufacturers instructions for ladder safety. Failure to follow this warning could result in death or serious bodily injury. CAUTION Always use appropriate lifting devices and/or helpers when lifting or holding heavy objects. NOTICE When using fasteners, do not over tighten. Soft materials such as fiberglass and aluminum can be "stripped out" and lose the ability to grip and hold. The state of California requires the following warning:
CALIFORNIA PROPOSITION 65 WARNING This product contains chemicals known to the state of California to cause cancer or birth defects or other reproductive harm. Californias Proposition 65 requires this warning to be given to customers in the state of California. 4 070029-001r1 CAREFREE OF COLORADO INSTALLATION INSTALLATION MANUAL BT12 WIRELESS AWNING CONTROL SYSTEM WARNING SHOCK HAZARD. Always disconnect battery or power source before working on or around the electrical system. Important Note: To comply with 2015 NFPA 1192 RV Standard, Section 6.4.9, switches must be mounted as follows:
a) Installed in a dedicated switch cabinet with a latching door; or, b) Installed with the optional covered bezel available from Carefree; or, c) Installed in a cabinet with a latching door where the switch is protected and CANNOT be activated by any items or cargo that may move or shift during transit; or, d) Installed with an interrupt circuit that disables awning extension when the vehicle is in motion. 1. The BT12 module provides an ignition lockout option. When the IGN LOCK is connected to the vehicle PCM or other switched source the following parameters are set:
i) ii) iii) If tied to +12Vdc = Standard Extend command disabled If Open = Awning Active If tied to GND = RTL (Retract Then Lock) Awning retracts, extend command disabled To Start:
1. Determine the location for the awning switches, LED switch and BT12 control module. NOTE: The BT12 control module leads are 6" in length. If the distance between the module and the switches is greater than 6", the installer must furnish splice wires for the extra distance. Use appropriate size wire gauges. Use appropriate sized butt splices to secure connections. 2. Route the motor cable and LED harness to the location of the module. 070029-001r1 5 INSTALLATION MANUAL BT12 WIRELESS AWNING CONTROL SYSTEM BT12 CONTROL MODULE INSTALLATION
(Refer to the wiring diagram on page 8.) NOTICE Do not mount the unit near heat producing elements such as LP appliances or engine exhaust components. NOTICE For best reception, do not mount the unit near or on a metal surface. 1. Clean the mounting surface. The surface must be flat CAREFREE OF COLORADO Mounting Tape and clean for the mounting tape to properly adhere. 2. Remove the release paper from the tape on the back of the module and firmly press the module onto the mounting surface. NOTE: The module may be oriented for best fit with access to the wire leads. 3. Attach the motor wires for corresponding wire colors) to the module leads for the motor using 14-16awg butt splices. to diagram
(refer Remove Release Paper 4. Run a minimum 14 awg wire to chassis ground. Suitable ground would be the vehicle chassis or BT003 conductive structure connected to the chassis. Splice the wire to the module GND lead with a 14-
16awg butt splice. 5. Run a minimum 14 awg wire from the power distribution panel (auxiliary battery circuit) or equivalent. The circuit should be protected by a 15-amp fuse. Splice the wire to the module +12V lead with a 14-16awg butt splice. NOTE: If the wire run is 30 feet or longer for +12Vdc and/or GND, use 12awg wire to prevent voltage drop. Use the appropriate butt splices for the wire size. 6. Splice the Black wire from the LED Harness to the module LED GND lead (Black) with a 18-22awg butt splice. 7. Route the module LED + lead (RED) to the LED switch location. Use 20awg wire and 18-22awg butt splice to extend the lead as necessary. 8. Route the module IGN LOCK lead (Green) to the vehicle PCM or other switch source (used for ignition lockout). 9. Route the remaining wires (Violet, Gray, Yellow and Brown) to the location for the awning control switches. Use 20awg wires and 18-22awg butt splices to extend the leads as necessary. 6 070029-001r1 CAREFREE OF COLORADO AWNING SWITCH INSTALLATION
(Refer to the wiring diagram on page 8.) 1. At the switch location cut a 2 5/16"
[5.9cm) x 1 1/2" [3.8cm] hole. 2. From the module, terminate the three (3) 20awg wires (Brown, Yellow and Gray) with .187, 18-20 awg female terminals. Attach to the EXTEND/RETRACT switch as shown in the wiring diagram. 3. From the module, terminate the Violet wire with a .187, 18-20 awg female terminal. Attach to the ON/OFF switch. INSTALLATION MANUAL BT12 WIRELESS AWNING CONTROL SYSTEM Optional Covered Bezel 1" [2.5cm]
2.32" [5.9cm]
ON RETRACT OFF EXTEND Awning Control 1.5"
[3.8cm]
ON RETRACT 4. Run a minimum 14 awg wire to chassis ground. Suitable ground would be the vehicle chassis or conductive structure connected to the chassis. Terminate the wire with
.187, 14-16 awg female terminal and connect to the second terminal of the ON/OFF switch. NOTE: If the wire run is 30 feet or longer, use 12awg wire to prevent voltage drop. Use the appropriate wire terminals for the wire size.
#6 x 1/2" Screw (x4) OFF Awning Control BT001 EXTEND 5. Push the wires and switches into the hole then attach the switch frame using 4 #6 x 1/2" screws. 6. Snap the switch bezel over the switch frame. LED SWITCH INSTALLATION NOTE: Carefree offers two switch options, unlighted and lighted. Installers may choose to furnish the control switch or may wire directly to a multiplexing control center.
#6 x 1/2" Screw (x2) 1.13"
2.9"
ON OFF 1.88"
White/Violet (20awg) To +12VDC Single Pole, Single Throw Switch 1.5"
GND To +12VDC White/Violet (20awg) Lighted Single Throw Switch To Multiplexing Controller White/Violet (20awg) Multiplexing Control Connection BT004d 1. Determine the location of the switch. 2. At the switch location, cut a 1 1/8" x 1 1/2" hole. 3. Wire the switch as shown. Wire terminals at the switch are .187, 18-24 awg female disconnects. NOTE: The lighted switch has a third terminal. This is wired to GND. 070029-001r1 7 BT12 WIRELESS AWNING CONTROL SYSTEM WIRING DIAGRAM To +12VDC 1 GND Top F F Bottom Black Red A M M F F LED Strip 4 To +12VDC Red Black B INSTALLATION MANUAL CAREFREE OF COLORADO Red (16awg) Black (16awg) Blue (16awg) White (16awg) White/Red (20awg) White/Black (20awg) White/Violet (20awg) To vehicle PCM or other switched source To +12VDC Control Module 3 Violet
(18awg) Green
(18awg) Gray
(18awg) Yellow (18awg) Brown (18awg) 2
) g w a 8 1
(
d e R
.187, 18-20awg Female Spade Terminals (x5) Extend/
Retract On/Off Rear View of Switch Assy Top Black Red F F M M F F Blue (16awg) White (16awg) Bottom Eclipse, Travelr, Latitude, Longitude, Altitude Blue Brown Blue (16awg) White (16awg) Freedom WM, Freestyle WM, Marquee Brown Blue Blue (16awg) White (16awg) Freedom RM, Freestyle RM A B R O T O M A B R O T O M A B R O T O M DETAIL A Motor Connect White/Violet (20awg) To +12VDC Single Pole, Single Throw Switch GND To +12VDC White/Violet (20awg) Lighted Single Throw Switch To Multiplexing Controller White/Violet (20awg) Multiplexing Control Connection DETAIL B LED Switch Options BT002d For GND, run a minimum 14 awg wire to chassis ground. Suitable ground would be the vehicle chassis or conductive structure connected to the chassis. For +12Vdc, Run a minimum 14 awg wire from the power distribution panel (auxiliary battery circuit) or equivalent. The circuit should be protected by a 15-amp fuse. NOTE: If the wire run is 30 feet or longer, use 12awg wire to prevent voltage drop. Use the appropriate wire terminals for the wire size. The BT12 module leads are 6" in length. If the distance between the module and the switch is greater than 6", the installer must furnish splice wires for the extra distance. Use appropriate size wire gauges. Use appropriate sized butt splices to secure connections. The BT12 module provides an ignition lockout option. When the IGN LOCK is connected to the vehicle PCM or other switched source the following parameters are set:
a) If Open = Awning Active b) If tied to GND = RTL (Retract Then Lock) Awning retracts, extend command disabled c) If tied to +12Vdc = Standard Extend command disabled The LED connection is optional to provide LED controls through the app for white LEDS only. White LEDS can also be installed per the standard LED installation without BT12 Controls. RGB lights must be installed per the standard RGB installation. 1 2 3 4 8 070029-001r1 INSTALLATION MANUAL CAREFREE OF COLORADO INSTALLING THE BT MOTION SENSOR The system operates by gauging the motion of the awning's front edge (roller tube or lead rail). When the motion exceeds the preset threshold the system retracts the awning. The factory default is 3 on a scale from 1 to 5. When using the mobile app, the sensitivity can be adjusted for personal preference. The sensor is located in the motor head for vertical arms or in the lead rail for box awnings. Altitude / Longitude / Latitude 1. Remove the front cover on the motor side. BT12 WIRELESS AWNING CONTROL SYSTEM Battery Pull Tab Attach Bracket to Inside of Rear Cover The cover snaps onto the rear cover. 1.1. Altitude / Longitude: Press in on both sides of the rear cover in the area shown. Rotate the cover up and off. Motion Sensor Thumb Tab 1.2. Latitude: Press the bottom of the rear cover until the front cover releases then lift the front cover off. Front Cover Thumb Tab Down Remove Release Paper Press on both sides of the rear cover to release front cover 2. Clean the inside surface of the rear cover. 3. Remove release paper from the mounting tape on the back of the bracket. the 4. Firmly press the bracket onto the inner surface of the rear cover. Small Box Awnings This option is available for Freestyle WM and Freestyle RM. It is not available for the Freedom WM, Freedom RM or Marquee. 1. Open the awning to expose the inside of the lead rail on the motor side. 2. Clean the inside surface of the lead rail. 3. With oriented horizontally, as shown, remove the release paper from the mounting tape. the module bracket 4. Firmly press the bracket onto the inner surface of the lead rail between the end plate and arm connector on the motor side of the awning. Thumb Tab Pairing the Motion Sensor NOTE: Only 1 active motion sensor can be paired to the BT12 Control Module 1. After completing installation restore power to the awning and extend the awning using the switches. the Battery Pull Tab Altitude / Longitude
(Altitude Shown) Battery Pull Tab Motion Sensor Thumb Tab Front Cover Attach Bracket to Inside of Rear Cover Remove Release Paper Thumb Tab Down Press Up On Rear Cover to Release Front Cover Latitude Motion Sensor Remove Release Paper 2. Place the awning in pairing mode (refer to page 10). Small Box Awning
(Freestyle WM Shown) BT013 3. Remove the battery pull tab from the motion sensor. 4. Hold the motion sensor next to the control module for 2-3 seconds. The module should be paired. 5. Holding the sensor vertically with the Carefree logo upright, repeatedly move the sensor vertically up and down to simulate a brisk wind. The awning should retract. 6. Snap the module in the sensor bracket. 7. For Altitude / Longitude / Latitude: Snap the front cover onto the rear cover. Hang the cover on the top and swing down until it clicks. 070029-001r1 9 CAREFREE OF COLORADO INSTALLATION MANUAL BT12 WIRELESS AWNING CONTROL SYSTEM SETTING THE SYSTEM INTO PAIRING MODE After installation, the mobile app and peripheral devices must be paired to the BT12 module. 1. Restore power to the awning if needed. 2. Turn the awning power switch to OFF. 3. Open the pairing mode for the awning. 3.1. Press and hold the extend switch. 3.2. Continue holding the extend switch and turn the power switch to on. 3.3. Continue to hold the extend switch for 2-3 seconds and release. 3.4. The awning is now in pairing mode for 5 minutes. 4. The BT12 control module will automatically pair to the device then go to working mode. NOTES:
The module will pair to the physically closest unpaired device first. Repeat the pairing steps for each additional device (the module remembers the devices that have been paired). Refer to the Carefree Connects Mobile App manual for setting up and pairing a smart device (such as a smart phone or tablet). The app manual is available at www.carefreeofcolorado.com. Multiple devices can be paired to the awning but only a maximum of 8 peripheral devices can be active at one time such as key FOBS and one (1) mobile device. Only one active BT Motion Sensor can be paired to the BT12 Control Module. Only one mobile device (smartphone or tablet) can be active at a time. Testing the Remote Functions:
1. Turn the awning power switch ON. 2. On the remote, press and release the extend button. Press a second time to stop the awning motion. 3. Repeat for the retract button. NOTE: The LED controls are for White LED strips that are wired to the BT12 module. 4. Extend the awning so that the LED strip is visible. 5. Turn the LED power switch ON. 6. Press the ON/Off button to turn the LEDs on and off. 7. Press the LED Bright to brighten the LEDs. Press the LED Dim to lower the LEDs 10 070029-001r1 INSTALLATION MANUAL CAREFREE OF COLORADO BATTERY REPLACEMENT BT MOTION SENSOR If the motion sensor batteries are low, the awning will beep every 30 seconds (when the power switch is ON). This will continue until the batteries are replaced. The awning will operate normally after the batteries are replaced. The motion sensor uses two (2) 675 batteries; batteries are available at local battery outlets. BT12 WIRELESS AWNING CONTROL SYSTEM Thumb Tab Remove Screws and Cover Remove Module From Bracket Replace Batteries Match Battery Orientation 675 SIDE DOWN Note: Refer to the module installation for location in awning. BT007 1. Pull the thumb tab of the bracket away from the module and lift the module out of the bracket. NOTE:
It is not necessary to remove the mounting bracket. 2. Remove the two screws and the rear cover. 3. Replace the two batteries. Match the new battery orientation with the old batteries. 4. Replace the cover and screws. 5. Snap the module into the mounting bracket. The module will only fit one way in the bracket. BT REMOTE The remote uses one (1) CR2032 battery; batteries are available at local battery outlets. 1. Carefully remove the back cover using a coin in the slot at the Remove Back Cover bottom corner of the remote. 2. Remove the old battery and insert a new battery with the +
terminal facing up. 3. Snap the back cover on. Slot Coin CR2032 Replace Battery Match Battery Orientation 070029-001r1 BT008 11 BT12 WIRELESS AWNING CONTROL SYSTEM INSTALLATION MANUAL BT12 WIRELESS AWNING CONTROL KITS The following kits and components are available for the BT12 Wireless Awning Control System. CAREFREE OF COLORADO 5 SR0115 Cover Bezel Kit ON RETRACT OFF EXTEND Awning Control ON RETRACT OFF Awning Control EXTEND 1 Switch Kit R019468-006 2 BT12 Control Module R060780-001 3 BT Motion Sensor R060784-001 4 BT Remote R001911 BT501 KIT NUMBER SR0117 SR0118 SR0119 SR0120 R001911 SR0115 INCLUDED COMPONENTS 1 ON RETRACT OFF Awning Control EXTEND Included Included Included Included 2 Included Included Included Included 3 Included Included 4 Included Included Included Included 12 070029-001r1