FCC ID: 2AAZPCT0311YB DC power ceiling fan remote control

Model#CT0311YB+DC8-116MR(with light function) DC POWER CEILING FAN REMOTE CONTROL MANUAL INSTALLATION INSTRUCTIONS NOTE: This unit is to be used for the control of DC power ceiling fan and in an AC120V 60Hz power supply only. Output Power: 50W (Max.) for motor and 60W (Max.) for LED light. Important To reduce the risk of re or electrical shock, do not use a full range dimmer switch to control fan speed.

: Using a full range dimmer switch (not included) to control fan speed will damage the fan. ACL ACN White Black Yellow/Green FORLIGHT White FORLIGHT Blue MOTOR3 Gray MOTOR1 Red MOTOR2 Purple FIG.1 ANT 1. Switch power o at fuse box or circuit breaker before you begin installing the fan. 2. Take wiring connections as indicated FIG. 1. 3. Launch distance for remote control: about 10m. 4. The remote learning function setting process:

Learning Button Insert the 2pcs of batteries into the remote control,with the fan

Step 1) power o.(FIG. 2)

Step 2) Within 60 seconds of restring power to the fan, you must press "FAN on/o" button about 5 seconds.Once the receiver has detected the frequency, the receiver will "BeepBeep Beep"three times, then they pair successfully. This will indicate the receiver has learned the frequency that was previously selected on the remote control. Step 3): After the AC power is on, do not press any other button on the remote control before setting learning. Doing so will cause the procedure to fail. Step 4):After completing the steps above, you should be able to operate the ceiling fan and lampe. If the fan is not responding to the remote control, please turn the power o to the receiver.And repeat Step2). NOTE:

(1)One transmitter to one receiver matching has been done for you as leaving factory.You have been able to control your fan when you connect the fan with pairing receiver correctly at this moment.

(2)The transmitter can only record two sets of learning codes.If you want to control one fan only,you could follow the steps above to learn to match the receiver again with your transmitter.

(3)When you learn the code for the third time on the same frequency receiver with the transmitter, then the rst recorded learning code will be removed out, and the receiver that was learned the rst time will be uncontrollable FIG.2 FUNCTION OF REMOTE CONTROL:(FIG.3)

-Fan on/o:Click it to turn on/o the fan;press and hold it for 5s within 60s after power-on to start pairing.

-Natural air:Cycle of highlowhigh level: When enabled, the indicator will light up once from top to bottom; press level or fan switch button to quit this mode.

-Wind speed +:Green indicator: Progressive increase.

-Wind speed -:Green indicator: Progressive decrease.

-Timing 1HR:Indicator 1 and 2 light up simultaneously, the fan will stop within 1HR; lamp is not controlled in timing mode; when timing is enabled, the timing of other buttons will be cancelled.

-Timing 4HR:Indicator 3 and 4 light up simultaneously, the fan will stop within 4HR; lamp is not controlled in timing mode; when timing is enabled, the timing of other buttons will be cancelled.

-Timing 8HR:Indicator 5 and 6 light up simultaneously, the fan will stop within 8HR; when timing is enabled, the timing of other buttons will be cancelled; hold and press 8HR for further WIFI pairing.

-Lamp switch:Click lamp switch;Press and hold it to adjust the brightness. FIG.3

-Color temperature adjusting:It could let lamp change color temperature when you click this button.

-Fan reverse rotation:Blowing up.

-Fan forward rotation:Blowing down

-Mute switch:Press and hold "Fan on/o" and "Wind speed -

" buttonfor over 5s tomute; repeat this operation to unmute. NOTE:The transmitter&receiver is incorporated with last memory function.This function stores your last setting in memory and the next time you turn on the fan,fan will operate the last setting. INSTALLING WALL MOUNTED HOLDER Attach wall mounted holder using the two provided screws. (FIG. 4) FIG.4 Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 Note:

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

(2) this device must accept any interference received, including interference that may cause undesired operation.

Model:

FCC ID:

CT0311YB 2AAZPCT0311YB This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference and 2) This device must accept any interence received including interference that may cause undesired o eration. p SIZE:30*30MM

Carewell Electric Technology (Zhongshan) Co., Ltd Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 01-10-2024 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID:2AAZPCT0311YB Carewell Electric Technology (Zhongshan) Co., Ltd(the applicant) certifies that the equipment for which authorization is sought is notcovered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, ALLEN XU Rev 1/26/2023 Carewell Electric Technology (Zhongshan) Co., Ltd Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 01-10-2024 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AAZPCT0311YB Carewell Electric Technology (Zhongshan) Co., Ltd(the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely, ALLEN XU Rev 1/26/2023

Carewell Electric Technology (Zhongshan) Co., Ltd Date:January 10, 2024 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID:2AAZPCT0311YB Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Schematics Block Diagram Operational Description File Name Schematic.pdf Block Diagram.pdf Operational Description.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Carewell Electric Technology (Zhongshan) Co., Ltd Signature ALLEN XU/Manager Typed name and Title

Carewell Electric Technology (Zhongshan) Co., Ltd FCC ID:2AAZPCT0311YB POWER OF ATTORNEY Date: January 10, 2024 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern:

We, the undersigned, hereby authorize Waltek Testing Group (Foshan) Co., Ltd.

(Dara Zhou) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group (Foshan) Co., Ltd. (Dara Zhou) on our behalf shall have the same effect as acts of our own. This authorization expires on January 10, 2025 . This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Carewell Electric Technology (Zhongshan) Co., Ltd are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Carewell Electric Technology (Zhongshan) Co., Ltd Signature ALLEN XU/Manager Typed name and Title

Carewell Electric Technology (Zhongshan) Co., Ltd. Date:2024-01-09 FCC ID:2AAZPCT0311YB Carewell Electric Technology (Zhongshan) Co., Ltd. Dan s Electronics of the ling of the application, agent for service of process for the above referenced FCC ID. Carewell Electric Technology (Zhongshan) Co., Ltd.(the Applicant)accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment.

(the Applicant) certies that, as of the date Etc. Inc.(U.S. agent). is our designated U.S. Dan s Electronics the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Etc. Inc. (U.S. agent) accepts, as of the date of the ling of the application, FRN:The agent for service of process does no other business with the FCC and does not have an FRN Signed by (printed name): Andrew Lawrence Williard Signature:

FRN:0022969950 Signed by (printed name):ALLEN XU Signature: