CGA0101v2 Wireless Cable Gateway Quick Installation Guide Package Contents
CGA0101 cable modem * 1
Quick Installation Guide * 1
RJ-45 CAT 5e cable * 1
12 V/1.5 A Power Adaptor * 1
Telephone cord * 1 Rear Panel and Hardware Connection This chapter describes the proper steps for connecting your cable modem. Please be sure to follow the steps in the sequence outlined below. Failure to do so could result in improper operation or failure of your cable modem. Please be reminded this product CGA0101v2 is designed to stand in vertical position in order to keep the ventilation as clear as possible. Please do not put it down horizontally. Step 2 Connecting to a Network Interface Cord Step 1 Connecting the Coaxial Cable Step 3 Connecting the Telephone cord Step 4 Connecting to the AC Adapter Step 1: Connect a cable by feeding the F-connector on the back of the cable modem. Ensure the center conductor of the 75 ohm coaxial cable is inserted directly into the center of the F-connector. Secure the coaxial cable by carefully threading the outer shell of the coaxial cable connector onto the F-connector in a clockwise direction until tight. Be careful not to over-tighten the connector or you may damage either the connector or the cable modem. Step 2: Connect the cable modem to IEEE 802.3 10Base-T / 802.3u 100Base-TX / 802.3ab 1000Base-T Network using a RJ-45 male-terminated Ethernet cable. This cable modem equips with two Ethernet ports, you can connect two PCs to the cable modem at the same time if necessary. Step 3: Connect the telephone sets to TEL. Use RJ-11 telephone line to connect TEL port on the cable modem and telephone socket on telephone Step 4: Connect the AC Adapter to the cable modem by inserting the barrel-shaped connector into the mating power connector on the back of the cable modem. Exercise carefully to ensure the connectors are properly aligned prior to insertion and ensure the two connectors engage completely. The cable modem is shipped with an AC adapter. Remember to use only power adapter that came with the cable CGA0101v2 Wireless Cable Gateway Quick Installation Guide modem. Other power adapters might have voltages that are not correct for your particular cable modem. Using a power adapter with the wrong voltage can damage the cable modem. Step 5: Adjust the antenna if necessary. Step 6:The screen of the coaxial cable is intended to be connected to earth in the building installation. Front Panel & LEDs There are nine Light-Emitting-Diodes (LEDs) located on the front panel top provide status information to the user. CGA0101v2 Wireless Cable Gateway Quick Installation Guide LED NAME COLOR MODE STATUS POWER Green DS US Green Green Green Green ONLINE Green LAN1 LAN2 Green
& Orange Green
& Orange On Off DC power connected No DC power connected Blinking Downstream scanning On Off On Off Downstream locked Cable interface idle W/DS locked W/DS disabled or CM standby Blinking Upstream ranging On Off On Off Upstream locked Cable interface idle W/US locked W/US disabled or CM standby Blinking CM provisioning On Off On CM on-line Cable interface idle ETH device connected (Green: GbE, Orange: FE) Blinking Data in traffic Off No ETH device connected On ETH device connected (Green: GbE, Orange: FE) Blinking Data in traffic Off No ETH device connected On WiFi enabled Wi-Fi Green Blinking Data in traffic WPS Green TEL Green Off WiFi disabled Blinking WPS in paring On Off WPS enabled WPS disabled Blinking TEL provisioning or off-hook On Off TEL on-hook TEL disabled CGA0101v2 Wireless Cable Gateway Quick Installation Guide Accessing the Web Management For easy-changing the default settings, a Web-based GUI is built-in for your access. Use the following procedures to login to your CGA0101v2. 1. Open your web browser. Type the default IP address of the CGA0101v2 (e.g. http://192.168.0.1) and press Enter. Configuring Your WAN Connection The DHCP page allows you to activate/deactivate the DHCP server function of the CGA0101v2, and, if the DHCP server is activated, to see DHCP leases it has provided. Enable CGA0101v2s DHCP server to allocate IP address to the connected LAN client (PC) and configure the Starting Local Address to be issued. You can also set the maximum number of PCs to which the CGA0101 will issue IP addresses and the release time (in second). CGA0101v2 Wireless Cable Gateway Quick Installation Guide SSID:
CGA0101v2_8C9D Check your CGA0101v2 Access Information There is a label pasted to the bottom of CGA0101v2 case. In that label, you can obtain following information. Pls note, following label is just an example, each CGA0101v2 has their own label and setting value. Pls follow your label information to access and configure CGA0101v2. In normal case, you dont need to change anything, all setting have been set and work properly. SSID: This is used for your CGA0101v2 wireless setting use, and, this setting has already been set to WPA2-PSK(TKIP+AES) password: password Web Management:
http://192.168.0.1 login: admin your CGA0101v2. WPA Pre-Shared Key: This is the password for your wireless client when connecting to CGA0101v2. You will be asked to key in this password so as to connect via wireless connection. Web Management: This is the URL when you like to access to CGA0101v2. You can simply type http://192.168.0.1 in Microsoft Internet Explorer or any other internet browser to access CGA0101v2 web management page. Login: This is the value when accessing CGA0101v2 web management page. You will be asked to key in this default value to access CGA0101v2. Password: This is the value when accessing CGA0101v2 web management page. You will be asked to key in this default value to access CGA0101v2. CGA0101v2 Wireless Cable Gateway Quick Installation Guide Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
-
-
-
-
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. CGA0101v2 Wireless Cable Gateway Quick Installation Guide FCC Statement This device complies with Class B Part 15 of the FCC Rules. The device generates, uses and can radiate radio frequency energy and, if not installed and used as instructed, may cause harmful interference to radio communication. Only Coaxial cables are to be used with this device in order to ensure compliance with FCC emissions limits. Accessories connected to this device by the user must comply with FCC Class B limits. The manufacturer is not responsible for any interference which results from use of improper cables, or which results from unauthorized changes or modifications to the device.
"A Minimum 26 AWG Line Core should be used for connection to the cable modem"
CGA0101v2 Wireless Cable Gateway Quick Installation Guide Canada-Industry Canada (IC) Operation is subject to the following two conditions:
this device may not cause interference and this device must accept any interference, including interference that may cause undesired operation of the device. IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment with IC radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with IC RF exposure compliance requirements, please follow operation instruction as documented in this manual. Warranty Items sold by manufacturer/distributor/agent, hereinafter called "Seller", are warranted only as follows:
Except as noted below Seller will correct, either by repair or replacement at its option, any defect of material or workmanship which develops within one year after delivery of the item to the original Buyer provided that evaluation and inspection by Seller discloses that such defect developed under normal and proper use. Repaired or replaced items will be further warranted for the unexpired term of their original warranty. All items claimed defective must be returned to Seller, transportation charges prepaid, and will be returned to the Buyer with transportation charges collect unless evaluation proves the item to be defective and that the Seller is responsible for the defect. In that case, Seller will return to Buyer with transportation charge prepaid. Seller may elect to evaluate and repair defective items at the Buyer's site. Seller may charge Buyer a fee (including travel expenses, if needed) to cover the cost of evaluation if the evaluation shows that the items are not defective or that they are defective for reasons beyond the scope of this warranty. The Seller makes no warranty concerning components or accessories not manufactured by it. However, in the event of failure of such a part, Seller will give reasonable assistance to Buyer in obtaining from the manufacturer whatever adjustment is reasonable in light of the manufacturer's own warranty. Seller will not assume expense or liability for repairs made outside the factory by other than Seller's employees without Seller's written consent. SELLER IS NOT RESPONSIBLE FOR DAMAGE TO ANY ASSOCIATED EQUIPMENT, NOR WILL SELLER BE HELD LIABLE FOR INCIDENTAL, CONSEQUENTIAL, OR OTHER DAMAGES. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING THE IMPLIED WARRANTY OF "MERCHANTABILITY" AND "FITNESS FOR PARTICULAR PURPOSE."
Note to CATV Sysrem Installer
"The EUT must be bonding the screen of the coaxial cable to the earth at the building entrance per ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable. Trademarks All trademarks are the property of their respective owners.