all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 3 4 5 |
|
User Manual | Users Manual | 1.44 MiB | ||||
1 2 3 4 5 | Cover Letter(s) | February 07 2018 | ||||||
1 2 3 4 5 | Cover Letter(s) | February 07 2018 | ||||||
1 2 3 4 5 | Test Report | February 07 2018 | ||||||
1 2 3 4 5 | Test Report | February 07 2018 | ||||||
1 2 3 4 5 | Test Report | February 07 2018 | ||||||
1 2 3 4 5 | RF Exposure Info | |||||||
1 2 3 4 5 | External Photos | |||||||
1 2 3 4 5 | Internal Photos | |||||||
1 2 3 4 5 | ID Label/Location Info | |||||||
1 2 3 4 5 | Cover Letter(s) | |||||||
1 2 3 4 5 | RF Exposure Info | |||||||
1 2 3 4 5 | Test Report | |||||||
1 2 3 4 5 | Test Report | |||||||
1 2 3 4 5 | Test Setup Photos | |||||||
1 2 3 4 5 | Cover Letter(s) | |||||||
1 2 3 4 5 | Test Report | |||||||
1 2 3 4 5 | Test Report | |||||||
1 2 3 4 5 | Test Report | |||||||
1 2 3 4 5 | External Photos | |||||||
1 2 3 4 5 | Test Report | |||||||
1 2 3 4 5 | Test Report |
1 2 3 4 5 | User Manual | Users Manual | 1.44 MiB |
M0065690-01 (en-us) January 2018 Operation and Maintenance Manual Cat Detect Proximity Awareness for MineStar Onboard Version 4 PA4 1-UP (Machine Control
& Guidance Products) SAFETY.CAT.COM DRAFT Important Safety Information i06558969 Most accidents that involve product operation, maintenance and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards, including human factors that can affect safety. This person should also have the necessary training, skills and tools to perform these functions properly. Improper operation, lubrication, maintenance or repair of this product can be dangerous and could result in injury or death. Do not operate or perform any lubrication, maintenance or repair on this product, until you verify that you are authorized to perform this work, and have read and understood the operation, lubrication, maintenance and repair information. Safety precautions and warnings are provided in this manual and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. The hazards are identified by the Safety Alert Symbol and followed by a Signal Word such as DANGER, WARNING or CAUTION. The Safety Alert WARNING label is shown below. The meaning of this safety alert symbol is as follows:
Attention! Become Alert! Your Safety is Involved. The message that appears under the warning explains the hazard and can be either written or pictorially presented. A non-exhaustive list of operations that may cause product damage are identified by NOTICE labels on the product and in this publication. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. The warnings in this publication and on the product are, therefore, not all inclusive. You must not use this product in any manner different from that considered by this manual without first satisfying yourself that you have considered all safety rules and precautions applicable to the operation of the product in the location of use, including site-specific rules and precautions applicable to the worksite. If a tool, procedure, work method or operating technique that is not specifically recommended by Caterpillar is used, you must satisfy yourself that it is safe for you and for others. You should also ensure that you are authorized to perform this work, and that the product will not be damaged or become unsafe by the operation, lubrication, maintenance or repair procedures that you intend to use. The information, specifications, and illustrations in this publication are on the basis of information that was available at the time that the publication was written. The specifications, torques, pressures, measurements, adjustments, illustrations, and other items can change at any time. These changes can affect the service that is given to the product. Obtain the complete and most current information before you start any job. Cat dealers have the most current information available. When replacement parts are required for this product Caterpillar recommends using Cat re-
placement parts. Failure to follow this warning may lead to pre-
mature failures, product damage, personal in-
jury or death. In the United States, the maintenance, replacement, or repair of the emission control devices and systems may be performed by any repair establishment or individual of the owner's choosing. DRAFT M0065690-01 3 Table of Contents Table of Contents Foreword ........................................................... 4 Safety Section Safety ................................................................ 5 Product Information Section General Information .......................................... 6 Operation Section Before Operation..............................................11 Operation......................................................... 13 Maintenance Section Maintenance Interval Schedule....................... 40 Index Section Index................................................................ 43 DRAFT M0065690-01 Maintenance The maintenance section, if present, is a guide to equipment care. Proper maintenance and repair are essential to keep the equipment and systems operating correctly. As the owner, you are responsible for the performance of the required maintenance listed in the Owner Manual, Operation and Maintenance Manual, and Service Manual. The Maintenance Interval Schedule lists the items to be maintained at a specific service interval. Items without specific intervals are listed under the "When Required" service interval. The Maintenance Interval Schedule lists the page number for the step-by-step instructions required to accomplish the scheduled maintenance. Use the Maintenance Interval Schedule as an index or "one safe source" for all maintenance procedures. Maintenance Intervals Use the service hour meter to determine servicing intervals. Calendar intervals shown (daily, weekly, monthly, etc.) can be used instead of service hour meter intervals if they provide more convenient servicing schedules and approximate the indicated service hour meter reading. Recommended service should always be performed at the interval that occurs first. Under extremely severe, dusty, or wet operating conditions, more frequent lubrication than is specified in the maintenance intervals chart might be necessary. Perform service on items at multiples of the original requirement. For example, at every 500 service hours or 3 months, also service those items listed under every 250 service hours or monthly and every 10 service hours or daily. Product Capacity Additional attachments or modifications may exceed product design capacity, which can adversely affect product performance characteristics, safety, reliability, and applicable certifications. Contact your dealer for further information. 4 Foreword Foreword Literature Information This manual should be read carefully before using this product for the first time and before performing maintenance. This manual should be stored in the product literature holder or in the product literature storage area. Immediately replace this manual if lost, damaged, or unreadable. This manual may contain safety information, operation instructions, transportation information, lubrication information, and maintenance information. Some photographs or illustrations in this publication show details or attachments that can be different from your product. Guards and covers might have been removed for illustrative purposes. Continuing improvement and advancement of product design might have caused changes to your product, which are not included in this publication. Whenever a question arises regarding your product, or this publication, consult your dealer for the latest available information. Safety The safety section, if present, lists basic safety precautions. In addition, this section identifies the text and locations of safety messages used on the product. Read and understand the basic precautions listed in the safety section before operating or performing lubrication, maintenance, and repair on this product. Operation The operation section, if present, is a reference for the new operator and a refresher for the experienced operator. This section includes a discussion of gauges, switches, controls, attachment controls, transportation, and towing information (if applicable). Photographs and illustrations guide the operator through correct procedures of checking, starting, operating, and stopping the product. Operating techniques outlined in this publication are basic. Skill and techniques develop as the operator gains knowledge of the product and its capabilities. Product Information The product information section, if present, may provide specification data, product intended use, product identification plate locations, and certification information. DRAFT 5 Safety Section Safety M0065690-01 Safety Section Safety SMCS Code: 1400 Safety Messages i06535611 Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your authorized dealer for replacement manuals. Proper care is your responsibility. Operation Ensure that you have read and understood the machine Operation and Maintenance Manual. Ensure that the screen is clean and adjusted properly. During system start-up, ensure that the audible alarm is heard during the display self-test. Prior to operating the machine, ensure that the brightness of the display is properly adjusted. Ensure that the brightness is adjusted after changes in conditions for ambient light. Check the display for system information warnings, if warnings are present, contact your supervisor. DRAFT 6 Product Information Section General Information Product Information Section General Information General Information SMCS Code: 7348; 7490 Intended Use i07059083 NOTICE Use of this system does not replace basic safety pre-
cautions and procedures for operating a machine. Refer to the Operation and Maintenance Manual of the machine for additional information. Cat Detect Proximity Awareness uses a combination of hardware and software, both onboard
(machine) and off board (infrastructure and office) to provide information to the machine operator. The machine sends GPS position to other machines over DSRC using V2x modules and to the office (server) over a wireless radio network. The V2x modules and the office then process all the messages from the individual machines within coverage. The V2x modules then share near real-time positions with the display and the office broadcast the messages out over the wireless radio network for machines that have shutdown or that are equipped with WiFi only Proximity Awareness. The display processes the messages and calculates machines of interest based on the position of your machines and the machines around you. The Proximity Awareness onboard system uses locations from a Global Positioning System (GPS), to enhance operator awareness of other equipment with a proximity awareness system installed and configured boundaries surrounding the machine. Detect helps increase operator awareness of machine surroundings. Detect includes a range of capabilities designed to assist the operator, including blind spot and proximity detection of fixed and mobile equipment. The system is highly configurable during setup and the on-board alarming behavior may differ from what is specified in this manual. Refer with your site supervisor for site-specific alarming behaviors. Detect Basics Definitions GPS: Global Navigation System (United States Department of Defense (DoD) NAVSTAR) M0065690-01 GLONASS: Global Navigation Satellite System
(Russia) GNSS: Global Navigation Satellite Systems
(generic naming used to describe the use of more than one positioning system) BSM Basic Safety Message is a standard format message that allows machines to share positioning information. DSRC Dedicated Short Range Communications is the communications protocol used to pass Basic Safety Messages. GPS/GNSS Availability Due to the nature of wireless communications and government controlled navigation systems, satellite timing signals may be lost, inaccurate, or of poor signal strength. The availability of satel-
lite-based positioning signals is beyond the con-
trol of both, the user and Caterpillar. Diagnostics to detect low accuracy or the loss of signal pro-
vide warnings to the operator. Failure to follow the instructions or heed the warnings could re-
sult in injury or death. Detect Proximity Awareness consists of several key elements that make up the complete system. At the heart of the Proximity Awareness system are the GNSS satellite constellations. Both GPS (United States) and GLONASS (Russia) are owned and operated by the defense departments of the countries that placed the satellites in orbit. While these government agencies recognize the great dependence the private sector has for these systems, an important message is, that for national security reasons, and at any time, the government can shut off, move/reallocate to a different slot, or alter the timing signals provided by these satellites. These government activities are out of the user and Caterpillar control and would have an adverse effect on the system to report accurate locations of the equipment. The onboard system incorporates diagnostics to detect low accuracy and/or no corrections to warn the operator of this condition. Elements of the Proximity Awareness System The following list defines elements of the Proximity Awareness system:
GPS/GNSS (Space element) Reference station (Ground element) Onboard Site Awareness system (User element) Wireless network, onboard, and infrastructure
(Two-way data communications) DRAFT 7 Product Information Section System Components M0065690-01 Office application (receives machine locations and broadcasts to all) Another key element embedded within the user element is the geographic local coordinate system calibration file. This file is a conversion file on the GNSS satellite receiver that is created by the mine site. The file calibrates the latitude, longitude, and elevation calculated by the satellite receiver into the mine site local coordinate system (northing, easting, and elevation). The accuracy of the indicated position in the plan view window of the Proximity Awareness system depends on the accuracy of the conversion file and measure-up of the machine during installation. Ensure that the GNSS reference point that is on the machine is placed over known site calibration point. Verify that the Proximity Awareness indicated that position matches the known mine site calibration point prior to placing the machine in service. Object Detection System (If Installed) If your machine is equipped with the Object Detect System, refer to the applicable system Operation and Maintenance Manual for further information. i07059086 System Components SMCS Code: 7348; 7490 The Detect onboard system consists of the following components:
Required:
Touchscreen monitor display V2x module GPS antenna Wireless radio (customer supplied) Optional:
Interface module Ethernet switch Medium precision satellite receiver Reference: Refer to Special Instruction, M0077913, Installation Procedure for theCat Detect Proximity Awareness System - PL671 for the installation requirements. DRAFT 8 Product Information Section System Components M0065690-01 Illustration 1 Stand-alone Proximity Awareness system
(1) GPS antenna
(2) Primary PL671 radio
(3) Secondary PL671 radio
(4) GS407 monitor display g06212749
(5) Third-party wireless radio DRAFT M0065690-01 9 Product Information Section System Components Illustration 2 Integrated with Fleet
(1) GPS antenna
(2) Primary PL671 radio
(3) Secondary PL671 radio Touchscreen Monitor Display The monitor display (4) provides the only operator interface to control the system. The monitor display provides the following functions:
Displays the position of the machine and other machines and configured areas in the plan view of the mine site Displays the status of system and diagnostic screens Generates visible and audible alarms based on proximity of machines and avoidance zones to machine V2x Module The V2x module is the systems main communication module. The V2x module performs the following functions:
Processes GPS positions
(4) GS407 monitor display
(5) Third-party wireless radio
(6) MS352 satellite receiver g06212780
(7) Ethernet switch
(8) Health Interface Module (HIM) Sends and received Basic Safety Messages GPS Antenna The GPS (1) antenna receives signals from the GPS satellites and provides them to the V2x module. Wireless Radio (Customer Supplied) The wireless radio (5), supplied by the customer, provides network connectivity between the onboard and office systems. Optional Items The following list depicts items that can be integrated when used with Cat MineStar Fleet Onboard Systems:
Interface Module (Optional) The interface module (8) performs the following function:
DRAFT M0065690-01 10 Product Information Section System Components Provides directional gear information from the machine to the monitor display Ethernet Switch (Optional) Supplied by the customer, the onboard Ethernet switch (7), provides network onboard between the Detect and Fleet systems. Medium Precision Satellite Receiver
(Optional) Medium precision MS352 GPS satellite receivers (6) can be configured to provide positions to the V2x module. DRAFT M0065690-01 Operation Section Before Operation Before Operation SMCS Code: 7348; 7490 i07059155 The Proximity Awareness system is highly con-
figurable. Depending on site configuration set-
tings within Detect Office, certain visual and/or audible alerts may not function for a particular event. Work with your supervisor to understand the alert behavior prior to using the system. Fail-
ure to follow the instructions or heed the warn-
ings could result in injury or death. Perform the following tasks prior to operating the machine:
Understand the functionality of all the views on the monitor display. Adjust the screen brightness for optimal viewing in the current conditions. Position the display to provide clear visibility of the screen from the operator seat. Ensure that the display is clean. Improper operation of an access platform could result in injury or death. Operators must carry out their duties properly and follow all instructions and guidelines given for the machine and access platform. Power ON/OFF Power is supplied to the system when the operator turns the machine keyswitch to the ON position. During the power-up process, the monitor and the V2x module will perform a self-test. During the self-
test, the monitor display will ensure that all the components are communicating. System status icons will be displayed if GPS or communication issues are present. The V2x module will illuminate LEDs to indicate what processes are functioning. 11 Operation Section Before Operation g03863938 Illustration 3 Caution screen After turning the keyswitch on, the CAT startup screen will appear while the application launches. The disclaimer splash screen and caution will appear. When the self-test is completed, the following actions occur:
The operator logon window appears (as required). The plan view becomes active. If a portion of the application fails or a system fault is detected, one or more of the following icons will be present:
No GPS This icon displays when there is no GPS communication. No communication to office This icon displays when broadband radio communication to the office is unavailable in WiFi mode or when BSMs are unavailable in V2x Mode. V2x Fault, High Priority All Machine to Machine communication functions with the V2x module are stopped. V2x Fault, Low Priority Some Machine to Machine communication functions with the V2x module are stopped. If the self-test fails, contact your site technology support or Cat technical communicator. If a fault is present, contact your site technology support or Caterpillar dealer. PL671 Indicator Lights The PL671 is a V2x module used on CaT Detect systems. The module contains 4 LED indicator lights that indicate the following scenarios:
DRAFT M0065690-01 g03738018 Illustration 4 Blue LED OFF Indicates no Ethernet link established. Blue LED Blinking The blue LED will blink to indicate Ethernet activity. Blue LED ON The blue LED will turn ON when the module has established an Ethernet link. Refer to Illustration 4 . 12 Operation Section Before Operation Green LED The purpose of the green LED is to indicate when the radio is powered ON or OFF. Green LED OFF Indicates that the radio is not powered. Green LED ON Indicates that the radio is powered properly and is ON. Green LED Blinking The green LED will blink when a fault has been detected that will prevent the application firmware from running. If the green LED is blinking, contact your Caterpillar dealer. Orange LED - GPS The purpose of the orange LED is to indicate whether a GPS fix has been made. Orange LED OFF The orange LED will be OFF when a GPS antenna is not found by the radio. Orange LED ON The GPS antenna is working properly, and can see enough GPS satellites to determine a good location fix. Orange LED Blinking The orange LED will have a constant blinking status when the GPS antenna is working properly, however not enough GPS satellites are viewable to get a good GPS location fix. If a blinking orange LED persists, contact your Caterpillar dealer. Yellow LED - DSRC Communications The purpose of the yellow LED is to indicate that a connection to the communication network, through DSCR, is being attempted. This action does not indicate that there is an appropriate signal, only that the hardware is working properly, and is capable of making a connection given that a signal is present. Yellow LED OFF Indicates no DSRC communications available. Yellow LED Blinking Indicates that there is a DSRC fault and the device is unable to launch communications. Blue LED - Ethernet The purpose of the blue LED is to determine when Ethernet connections are present. DRAFT M0065690-01 Operation Display Navigation SMCS Code: 7348; 7490 i07059186 13 Operation Section Operation Illustration 5 Display Arrow button (1) The arrow button is used to perform the following functions:
Highlight a selection (up/down) Manually adjust brightness level after the brightness button is depressed (right/ left) OK button (2) The OK button is used to select items that are highlighted. Tab button (3) The tab button is used to change the active screen between the plan view and the camera view. g06012813 Brightness button The brightness button is used to adjust the screen brightness. The screen will toggle between two settings. Press the button once to set the screen to the brightest mode, press the button again to set the screen to dimmest mode. Pressing and holding the brightness button for 3 seconds will cause the brightness adjustment window to appear. Alarm acknowledge button (5) The alarm acknowledge button is used for acknowledging alarms. Press the button once to acknowledge the alarm. If a new alarm occurs, the new alarm must be acknowledged again. Also, the alarm acknowledge can be used to mute the alarm until the next power cycle or when the button is held again for 10 seconds. When the alarm is muted, all alarms will still be displayed but not be audible. The mute feature depends upon site configuration. DRAFT M0065690-01 14 Operation Section Main Screen i07059236 Main Screen SMCS Code: 7348; 7490 The main screen allows the operator to monitor the operation of the system. The operator can perform the following tasks in the main screen:
Monitor the system state for Global Positioning System (GPS) and wireless communications conditions View system information Monitor position of other machines Access toolbar buttons The main screen is divided into seven areas. The following seven items make up the main screen:
System information window Plan window Status window Status bar Tool access window Toolbar button Note: Depending on how the site has configured the onboard display, the screen may look different. DRAFT M0065690-01 15 Operation Section System Information Windows Illustration 6
(1) Object Detection Proximity Bar
(2) System Information
(3) Speed Limit
(4) Operator Name
(5) Soft Button Panel including Up and Down Arrows, and OK buttons
(6) Soft Panel Next Screen button
(7) Soft Panel Alarm Acknowledge button
(8) Soft Panel Brightness button
(9) System Status and Warning
(10) Tool Bar Button Menu
(11) Truck State g06213236
(12) Status Window
(13) Object Detection Quadrant Detection
(14) Map View System Information Windows SMCS Code: 7348; 7490 i07060214 Illustration 7 System information window
(1) Speed limit
(2) Name of operator currently logged in g06012976 DRAFT 16 Operation Section Status Window A system information window displays information to the machine operator. A dedicated system information window is configured to display the time. An extra dedicated system information window is configured to display the current speed limit. The system information window that is at the top left of the screen can be configured to display several types of system information data in a single window. This system information displays one item at a time. Touching the system information window scrolls to the next configured system information item. Several types of system information data can be combined in the system information window. The following system information data can display:
Time Global Positioning System (GPS) accuracy Speed limit (KM/H or MPH) Operator name Note: Depending upon site configuration, different items may be available in the status information window. i07060230 Status Window SMCS Code: 7348; 7490 The status window continuously displays critical system and proximity information. Status icons provide status information to the operator for the following system components:
Global Positioning System (GPS) Radio Alarm Zones Speed limit violation The status bar will also display information about GPS proximity detection. GPS Status Icons Low Priority Low GPS icon displays when the GPS accuracy is low. M0065690-01 No GPS No GPS icon displays when there is no GPS communication. Radio Status Icon No communication to office No communication to office icon displays when broadband radio communication to the office is unavailable. Alarm Status Icon Alarm muted Alarm muted icon displays when the alarm has been muted by the operator. Proximity Critical Icons Low priority Low Priority icon displays when a machine equipped with proximity awareness is in the path or avoidance area of the machine or a machine around your machine. The low priority icon will display when the avoidance or path area of one machine has entered the avoidance or path area of another machine. This information is calculated based on GPS positions and the defined dimensions of your machine in the office. High priority High Proximity icon displays when a machine equipped with proximity awareness path, avoidance, or body area is in the body area of your machine or your machines path, avoidance, or body area of another machine. This information is calculated based on GPS positions and the defined dimensions of your machine in the office. V2x Module Icons High Priority High Priority icon displays when all machine to machine communication functions with the V2x module are stopped. Low Priority Low Priority icon displays when some machine to machine communication functions with the V2x module are stopped. Miscellaneous Icons Speed limit violation Speed limit violation icon displays when the machine exceeds the speed limit set for the class of machine being operated. Also, if the machine exceeds a speed limit for a zone that the machine is located in, the speed limit icon will display. DRAFT M0065690-01 Avoidance zone Avoidance zone icon displays when the machine enters an avoidance zone. i07060216 Plan Map Window SMCS Code: 7348; 7490 17 Operation Section Plan Map Window Illustration 9 g03142117 The name of the machine is displayed next to the icon. Refer to Illustration 9 . Illustration 8 Plan view window g02614938 The plan window is the main operating screen in Detect onboard. The plan window displays the following information:
Illustration 10
(1) Compass
(2) Machine icon
(3) Zone g03417508 Position of your machine Position of other machines Zones Reference points Position of Your Machine The position of your machine is displayed within the plan view window. Your machine is shown as the icon in the center of the screen. The compass (1) is located in the top left corner of the plan map. The red portion of the compass indicates which direction is north. In Illustration 11 , the machine is facing North. The operators machine is always centered on the screen with the front of the machine (2) facing the top of the display. This location matches the physical orientation of the machine. The map rotates around the machine during movement to ensure physical and displayed left, right, front, and rear always match. For example, zones that are displayed on the right are physically located to the right (3). DRAFT M0065690-01 18 Operation Section Plan Map Window Note: The machine icon will always display near the center of the map. The icon does not move or change directions. The machine icon will always appear to travel towards the top of the display, even when the machine is traveling in reverse. The movement of the machine on the map is shown by the map display changing machine instead of machine in the background, moving behind the icon of your machine. DRAFT M0065690-01 Zoom Level 19 Operation Section Plan Map Window Illustration 11 Zoomed out level
(4) Zoom in button
(5) Zoom out button
(6) Sliding scale g03142318 The operator can adjust the zoom level by pressing the zoom in (4) and zoom out (5) buttons on the plan screen. The sliding scale (6) in between the zoom buttons indicates the current level of zoom. After the operator has set the zoom level, the scale will disappear until the zoom button is pressed again. All machine icons are displayed to scale both with other machines and their physical environment such as zones and other machines. Position of Other Machines The position of other machines is displayed within the plan view window. Your machine is shown as the icon in the center of the screen. DRAFT 20 Operation Section Plan Map Window M0065690-01 Illustration 12
(6) Your machine
(7) Other machine Based on the operator-selected zoom Level, the machines are displayed in the plan view at the appropriate location and size dimensions. In addition, the statuses of the other machines are also displayed as on overlay of the machine icon. Machine Status Indicators NOTICE Use of this system does not replace basic safety pre-
cautions and procedures for operating a machine. Refer to the Operation and Maintenance Manual of the machine for additional information. Due to the nature of wireless communications and government controlled navigation systems, satellite timing signals may be lost, inaccurate, or of poor signal strength. The availability of satel-
lite-based positioning signals is beyond the con-
trol of both, the user and Caterpillar. Diagnostics to detect low accuracy or the loss of signal pro-
vide warnings to the operator. Failure to follow the instructions or heed the warnings could re-
sult in injury or death. g03142338 Illustration 13 Example of powered off icon
(8) Powered off machine g03416717 DRAFT M0065690-01 21 Operation Section Plan Map Window Powered Off This icon overlay indicates that the machine has been shutdown. This location is the last known good position reported to the office prior to the shutdown. Since the machine indicates that it is shutdown and has not reestablished communications to report a startup, then the last known position is likely the current position of the machine. Compactor Dragline Drill Fuel Truck or Water Truck Grader Hydraulic Shovel or Track Excavator Light Vehicle Scraper Soil Compactor, Underground Loader, or Wheel Loader Track Dozer or Track Loader Wheel Dozer Wheel Excavator Wheel Loader Other Machine with Heading Illustration 14 Example of out of communication icon
(9) Out of communication machine g03416721 Out of Communication This icon is only used for Detect machines in WiFi only mode and will not be used for V2x Mode machines. This icon overlay indicates that the machine has low GPS quality and/or has lost communication with the office. The current location on the screen is the last known good position reported to the office. The machine position on the display may not reflect the actual current position of the machine or machines. Machine Types The following list indicates the machine icon with the associated machine type:
Articulated Truck, Haul Truck, or Underground Truck Cable Shovel DRAFT 22 Operation Section Plan Map Window M0065690-01 Other without Heading Avoidance Zone Zone Polygons The proximity awareness feature does not re-
place basic safe operating procedures identified in the machine Operator and Maintenance Man-
ual. Machines equipped with proximity aware-
ness that are turned off and/or have lost radio communication, will not report current position of machine. Be aware of your surroundings be-
fore moving. Failure to follow the instructions or heed the warnings could result in serious injury or death. NOTICE Zones can be configured as any color. Note which type of zone you are approaching before you enter the zone. Zones are used to define specific areas on the mine site. The zone polygons display on the plan view screen to the operator. The operator may encounter the following types of zones:
Avoidance zones Speed limit zones Hazard zones Illustration 15 Avoidance zone
(8) Avoidance zone symbol
(9) Icon indicating machine has entered avoidance zone g03140116 Avoidance zones (8) are areas on the mine site that are restricted to the machine. An icon (9) will appear indicating that the machine has entered an avoidance area. Also, a do not enter notification message may display to the operator and a constant audible tone will sound. These alerts will continue until the machine leaves the avoidance zone. DRAFT 23 Operation Section Plan Map Window Entering and Exiting Zones The operator may be notified upon entry and exit of zones. The following notifications occur:
An audible alarm may sound depending upon site configuration. A popup text message may appear depending upon site configuration. The site may not be configured to display visual or audible warnings. Be aware of the site configu-
ration settings before operating a machine. Con-
sult your site operations manager. Failure to be aware of the site configuration settings could re-
sult in serious injury or death. Illustration 17 Example message g03057276 M0065690-01 Speed Limit Zones Illustration 16 Speed limit zones
(10) Speed limit zone
(11) Speed limit of the zone
(12) Current speed limit
(13) Speed limit violation icon g03140165 Speed limit zones are areas on the mine site where the speed limit changes from the set global speed limit. The current speed limit indicator (12) will update indicating the new speed limit of that zone to the operator. Note: If the global speed limit for your class of machine is lower than that of the zone, the speed limit will not change. If the machine exceeds the set speed limit, a single beep audible tone may sound and a visual speed limit violation icon (13) will be displayed until one of the following scenarios occur:
The machine speed drops below the speed limit The machine exits the speed zone and enters an area with a higher speed limit which is not being exceeded Hazard Zones Hazard zones are areas on the mine site that the operator needs to be aware of. These areas include but are not limited too, material spillage, damage to haul roads, and disabled machines. A do not enter notification and message may be displayed to the operator and a constant audible tone may sound. These alerts will continue until the machine leaves the hazard zone. DRAFT 24 Operation Section Tool Button Display Refer to Illustration 13 for an example of a message that would appear upon entry of a zone. i07060246 Tool Button Display SMCS Code: 7348; 7490 Illustration 18 Tool buttons g03064342 The tool button display expands vertical and buttons stack. The tool button display would allow for four buttons. A dedicated button at the bottom is available to scroll to other tool buttons. The following functions are accessible from the tool bar windows:
Operator login Send a mayday Mark hazards Diagnostics More buttons Delays Zone lock Data record M0065690-01 Illustration 19 Operator login This toolbar button is used to change the operator. g03410764 Illustration 20 g03106256 Send mayday This toolbar button is used to send a mayday to the office. The mayday feature is for non-critical situations where the operator requires assistance from of-
fice personnel. Due to the nature of wireless com-
munications, the mayday message is not ensured to reach the office in a timely manner. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility. Use other methods of communica-
tion for safety critical situations. Illustration 21 g03416726 Mark hazard This toolbar button is used to mark a hazard. DRAFT M0065690-01 25 Operation Section Visual Proximity Alarming Illustration 22 More buttons This toolbar button is used to cycle through the toolbars on the display. g03142760 Note: Additional toolbar buttons are available as part of the Cat MineStar Fleet system. Consult the Fleet Operator Maintenance Manual (OMM) for details on these buttons. i07073355 Visual Proximity Alarming SMCS Code: 7348; 7490 Fundamentals Illustration 23
(1) Avoidance area
(2) Machine body area
(3) Stop zone
(4) Projected path Proximity alarming is based on the following:
Machine speed Machine position Machine heading Machine dimensions and avoidance areas defined in office software g03320138 The avoidance area (1) is a fixed area around the machine, is configured in the office at the machine class level, and does not change based on the heading or the speed of the machine. The area does scale as the GPS accuracy decreases. For example, if the GPS accuracy is 1 m (3.28 ft) and the zone is configured as 2 m (6.56 ft), then the total avoidance zone around the machine would be 3 m (9.84 ft). DRAFT M0065690-01 26 Operation Section Visual Proximity Alarming Note: The dimensions of the machines and the avoidance areas of the machine are defined in the office software. The projected path (4) is added onto the avoidance area (1) at the (front or rear) of the machine to determine potential collisions. The total projected path is a mathematical calculation tied to the speed and direction of the machine and is defined in the office software. The projected path will increase as the speed of the machine increases and decrease in the direction of travel as the speed of the machine decreases. Alarms are based on priority. For example, if a machine is equipped with Object Detection and an object is detected by the Object Detection sensors, that alarm would have higher priority then a GPS-
based proximity alarm. Table 1 Priority Alarms Path Low Low High Other Machine Avoidance Low Low High Body High High Critical Your Machine Path Avoidance Body Refer to Table 1 for priority of the alarms. Low Priority Proximity Alarm Illustration 24
(5) Projected path g03061398 DRAFT M0065690-01 27 Operation Section Visual Proximity Alarming Illustration 25
(5) Projected path
(6) Machine proximity low alert icon g06012988 When the proximity awareness audible alarm is sounded, identify the other machine and the loca-
tion of the other machine before you move your machine. Failure to identify the location of the other machine prior to moving your machine can result in product damage, personal injury, or death. The low priority proximity alarm is generated when any of the following occur:
Projected Path on Projected Path Project Path on Avoidance Zone The projected path (5) appears on the plan view and a proximity alarm icon (6) appears in the bottom right corner. During caution, the icon is solid. Depending on configuration, an audible alarm tone is sounded. Refer to M0065690, Audible Alarms section for additional audible alarming details. Refer to Illustration 24 and Illustration 25 for an example of a low priority proximity alarm. High Priority Proximity Alarm The high priority proximity alarm is generated when any of the following occur:
Avoidance Zone on Body Area DRAFT 28 Operation Section Visual Proximity Alarming Projected Path on Body Area M0065690-01 DRAFT M0065690-01 Critical Proximity Alarm 29 Operation Section Visual Proximity Alarming Illustration 26 g03061444 DRAFT 30 Operation Section Visual Proximity Alarming M0065690-01 g06012994 Illustration 27 Critical Zone
(5) Projected path
(7) Stop zone alert icon A critical proximity alarm is generated when any of the following activities occur:
Body on body area The projected path (5) appears and a proximity alarm icon (7) appears in the bottom right corner. During the incident, the icon flashes, and an audible alarm tone is sounded. Refer to M0065690, Audible Alarms section for additional audible alarming details. Refer to Illustration 26 and Illustration 27 for an example of a critical proximity alarm. DRAFT M0065690-01 31 Operation Section Visual Proximity Alarming When the proximity awareness audible alarm is sounded, identify the other machine and the loca-
tion of the other machine before you move your machine. Failure to identify the location of the other machine prior to moving your machine can result in product damage, personal injury, or death. Unknown Machines Illustration 28 Unknown Machine g06013037 DRAFT 32 Operation Section Audible Alarms Unknown machines are treated as a rotational machine and have a default body area and avoidance area that is defined in the configuration file. These machines are represented as an arrow on the display. Illustration 28 shows an unknown machine type and the default body area and avoidance area. The same rules apply regarding alarming for machines that are unknown. i07071219 Audible Alarms SMCS Code: 7348; 7490 Proximity Alarming Filters The system can be configured to exclude Proximity Awareness alarms except for the body on body alarm. These filters are used generally with loading tools so that normal operating procedures do not produce nuisance alarming. Check with your supervisor regarding the site-specific configuration. Alarm Types The Proximity Awareness System sounds audible alarms for different types of events. The Proximity Awareness system is highly con-
figurable. Depending on site configuration set-
tings within Detect Office, certain visual and/or audible alerts may not function for a particular event. Work with your supervisor to understand the alert behavior prior to using the system. Fail-
ure to follow the instructions or heed the warn-
ings could result in injury or death. Note: Depending upon how the system is configured an audible alarm may not be present for all the scenarios listed below. Diagnostic Alarms The following alarms are raised for diagnostics:
Low GPS No GPS Loss of wireless communications System fault (if equipped with Object Detection) M0065690-01 Low GPS When GPS drops below the level defined in the configuration file, a single beep may sound depending on the site configuration for 1 second indicating to the operator that the system has a low GPS signal. No action is required by the operator. No GPS When GPS signal is lost for more than 5 seconds either due to the environment or equipment failure, the audible alarm may sound depending on the site configuration for 1 second indicating to the operator that the system has lost the GPS signal. The operator should contact the supervisor if the no GPS indicator does not disappear from the screen. Loss of Wireless Communications When wireless communications with the office are lost for more than 15 seconds either due to the environment or equipment failure, the audible alarm may sound depending on the site configuration for 1 second indicating to the operator that the system has lost wireless. The operator should contact the supervisor if the no communication to office status indicator does not disappear from the screen. Object Detection System Fault (if equipped with Object Detection) If the Object Detection detects a fault with one of the components within the system, the system will trigger a diagnostic code or an event. The operator should contact the supervisor to resolve the issue. Refer to the applicable Object Detection system for additional information regarding diagnostic codes and events. Zone Alarms The following alarms are raised for zones:
Speed zones Entering hazard zones Entering avoidance zones Speed Zones When the machine is operating in a speed limit zone and exceeds the speed limit of that zone, an audible alarm may sound depending on the site configuration continuously until the machine slows to the speed limit or exits the speed zone and enters an area with a higher speed limit which is not being exceeded. Entering and Exiting Zones When the machine enters a hazard zone, an audible alarm may sound depending on the site configuration for 1 second. Once the machine exits the zone, the audible alarm depending on the site configuration may then sound again for 1 second. DRAFT 33 Operation Section Audible Alarms M0065690-01 Entering Avoidance Zones When the machine enters an avoidance zone, the system may sound depending on the site configuration an audible alarm until the machine exits this zone. Proximity Alarms The following alarms are raised for proximity events:
Object Detection System (if equipped) Proximity Awareness Object Detection System (if equipped) The Object Detection system has various alarm levels depending upon the distant of the object to the machine. Refer to Operator and Maintenance Manual, Proximity Indicator (If Equipped with Object Detection) for more information regarding the various alarms of the Object Detection system. Proximity Awareness The Proximity Awareness system has two distinct alarm types based on the proximity of the object to the machine. Refer to Operator and Maintenance Manual, Proximity Alarmingfor more information regarding the various alarms of the Proximity Awareness system. Note: Alarms are automatically silenced once the machine is stopped and the gear selector is put into park or neutral. Once the machine is back in gear, the alarms are reactivated. This scenario applies to Object Detection and Proximity Awareness alarming only when installed on a machine utilizing VIMS supporting Cat MineStar system products. Consult your Site MineStar champion for more details. Table 2 Proximity Awareness Operator Notifications (GPS Based) Notification Levels Description Conditions Audible Alert Visual Notification Low Priority High Priority Critical Signals to the operator con-
trol new conditions Prepare to take action if required Signal to the operator new conditions have escalated Prepare to take action if required Signal when conditions are in violation of configured re-
gions and require immedi-
ate correction Path or avoidance regions of two machines intersect Path or avoidance regions intersect with another ma-
chines body region Body regions of two ma-
chines intersect Low Frequency On Off On Off tone pattern reference PA_Caution.wav on Dealer. Cat.Com Medium Frequency OnOf-
fOn Off On Off tone pattern reference PA_Warning.wav on Dealer.Cat.Com High Frequency OnOffOn Off On Off tone pattern reference PA_Critical.wav on Dealer.Cat.Com Solid yellow low priority icon Flashing red high priority icon Flashing red high priority icon
(continued) DRAFT 34 Operation Section Audible Alarms
(Table 2, contd) Miscellaneous Alerts Notification Levels M0065690-01 Description Conditions Audible Alert Visual Notification Fault Zone entry Speeding Signals when there is a loss of functionality that is not under operator control Indicates that a configured proximity zone has been entered Indicates that the speed limit has been exceded Poor GPS signal, loss of communication Configurable single 0.5 second alarm Fault icon in the System Status window Entering or exiting a prox-
imity zone Configurable single 0.5 second alarm Configurable pop-up Exceeding a class or con-
figured zone speed limit Constant tone Zone Violation Indicates that a restricted zone has been entered Entering or exiting a re-
stricted zone Constant tone Speed violation icon dis-
played in the System Sta-
tus window Zone violation icon dis-
played in the System Sta-
tus window Table 2 outlines the details of the various notification levels. Acknowledging Alarms Illustration 29 Acknowledge alarm g06013042 Depending upon the site configuration, the operator is able to acknowledge audible alarms. Acknowledging alarms silences the current active audible tone during that particular alarm event (for example, a radar object detection). Acknowledgment does not affect new events from generating audible alarms. Press the alarm button to acknowledge the alarm or alternatively, press the alarm acknowledge softkey (optional). The following alarm types can be acknowledged by the machine operator depending on the site configuration:
No GPS Speed limit violation Proximity Awareness events Muting Alarms Note: The alarm can be muted permanently based on-site configuration. By default, the alarms are not muted. Depending upon site configuration, the operator may be able to mute certain audible alarms. Muting the alarms silences the audible tones until the display is power cycled or the operator unmutes the alarms. The following alarm types can be muted by the machine operator depending upon site configuration:
Loss of radio communications Low GPS No GPS Interaction with machine that is out of communications Speed limit violation Proximity Awareness events To mute the alarms, perform the following procedure:
1. Press and hold the alarm acknowledge button for approximately 3 seconds. The disclaimer dialog will appear. Refer to Illustration 30 . DRAFT M0065690-01 35 Operation Section Operator Utilities Login Confirmation Select User Id Illustration 30 Disclaimer screen g03353994 2. Press the Accept key to mute the alarms. An icon will appear in the status window indicating that the system is muted. Illustration 32 Login Confirmation window g02155330 Illustration 31 Muted alarm icon g03353997 Note: The ability to mute an alarm type is configured specifically for each alarm type. 3. To unmute the alarm, press the alarm acknowledge button again for 5 seconds or cycle the power to the display. Illustration 33 Select User Id window g02155332 i06535633 2. If the Login Confirmation window appears, confirm the login. If the Select User Id window appears, perform the following procedure:
Operator Utilities SMCS Code: 7348; 7490 Logging In Change operator This button may be configured to display on the toolbar of the display. Press this button to log into the system. To log into the system, perform the following procedure:
1. Press the change operator button on the touchscreen of the display. One of the following windows will appear:
a. Select a user name in the selection tree of the Select User Id window. Alternatively, the user may press the Enter Id button. If the Enter Id button is used, the keypad will display to enter a numerical user ID. b. Press OK once a user is selected from the selection tree or a user entered. The Login Confirmation window will display. c. Select Yes to confirm the login. Press No to return to the Select User Id window. Note: In the Login Confirmation window, if No is selected, the Select User Id window will then display. DRAFT 36 Operation Section Operator Utilities 3. Press the OK on the touchscreen or press OK button on the display. Unknown Login M0065690-01 2. Press Yes to confirm the logout. The Select Id window appears for the next operator to log in. Note: Confirmation is not required if the office has disabled the operator confirmation window. Pre-Operation Check A pre-operation check may be configured to display at operator login. Each item in the checklist must be verified. Then each item is selected as pass or fail and the information is sent to the office. Note: The items in the checklist are customized by the site. Illustration 34 Login Failed window g02155702 The system will allow a user to perform a login as Unknown . This feature allows operators that cannot provide an ID to continue to operate the machine. If the operator enters an ID which is not found in the operator ID file, the Login Failed window will appear. Logging Out Change operator This button may be configured to display on the toolbar of the display. Press this button to log into the system. Illustration 35 Logout Confirmation window g02155713 To log out of the system, perform the following procedure:
1. Press the Change Operator button on the toolbar. The Logout Confirmation window will appear. Illustration 36 Pre-op safety check window g02645850 Perform the following procedure to process the pre-
operation check:
1. Select the first item in the list and the press OK if the item is operational or press BO if the item is broken. The next item will be highlighted automatically once the previous item has been processed. 2. Continue until all items in the list have been processed. 3. Press the Send button to send the information to the office. DRAFT 37 Operation Section Operator Utilities Illustration 37 Hazard Type Selection screen g02645979 Perform the following procedure to mark a hazard:
1. Press the hazard marking button. The hazard type selection screen will appear. 2. Select the type of hazard from the list and then press OK . The plan view window now displays a box around the machine. M0065690-01 Note: The checklist window may also be configured not to display the Cancel button. This feature ensures that the checklist is processed before operating the machine. Sending a Mayday Message Send mayday This button may be configured on the toolbar of the display. Press this button to send a mayday to the office. If a machine operator requires assistance in a situation, the operator can send a mayday message to the office. The system asks for confirmation before sending the notification. If the message is accepted by the dispatcher in the office, the office can then send a mayday message to all machines on the site. The mayday feature is for non-critical situations where the operator requires assistance from of-
fice personnel. Due to the nature of wireless com-
munications, the mayday message is not ensured to reach the office in a timely manner. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility. Use other methods of communica-
tion for safety critical situations. 1. Press the send mayday button on the touchscreen for the display. The Mayday window appears. 2. Press OK to confirm sending a mayday message. Press OK on the display or Yes on the touchscreen. A mayday message will be sent to the office. When received in the office, the mayday displays as an Urgent Alarm pop-up message on every MineStar Client that is running at the time of the event. The event is also captured in the alarm monitor page in the system. Marking a Hazard Hazard marking button Press this button to mark the location of on-road hazards. Detect Proximity Awareness on-board provides a method to allow machine operators to mark the location of on-road hazards that are encountered while in transit. Once the operator presses the hazard marking button, the operator selects the type of hazard and then locates the hazard using a polygon on the screen. This information is then sent to the office. The hazard information is then sent to other machines for display on the screen. DRAFT 38 Operation Section Operator Utilities M0065690-01 Illustration 38 Polygon in plan view
(1) Adjustable poly
(2) Hazard marking tool button
(3) Confirmation key
(4) Cancel key 3. Use the arrow keys shown on the plan map or the physical keys on the display to position the box around the hazard. Note: If the GPS accuracy of the machine is too low, then this feature will be disabled. A dialog box will appear indicating to the operator that the functionality is disabled. 4. Press the confirmation button to create the polygon. The hazard waypoint information is then sent to the office. The office then sends the hazard information to other machines for display on the screen. Adjusting Screen Brightness Brightness button The brightness button is used to adjust the screen brightness. The screen will toggle between two settings. Press once to set the screen to the brightest mode, press again to set the screen to dimmest mode. g02645985 Illustration 39 Brightness adjustment mode
(5) Dim button
(6) Brighten button g03057509 Two brightness modes may be set. A day mode and a night mode are configured by the operator. Press and hold the brightness button for 3 seconds. The screen brightness adjustment window will display to set the two modes. Move the slider button towards the dimmer button to change the level of the minimum brightness and then release the slider button. This action will set the night mode level. Then move the slider button towards the brighter button to change the level of the maximum brightness and then release the slider button. This action will set the day mode level. Once the two modes are set, switching between the modes is possible by pressing the brightness button once. DRAFT M0065690-01 Note: At night, adjust the brightness of the display to a level that allows viewing comfort while not distracting from night time operation. 39 Operation Section Operator Utilities DRAFT M0065690-01 40 Maintenance Section Maintenance Interval Schedule Maintenance Section i07071803 Maintenance Interval Schedule SMCS Code: 1400 Every 8 Service Hours or Daily Display - Clean . 41 GPS Accuracy - Check . 41 GPS Mast - Align . 41 GPS Orientation - Adjust. 41 Harness and Cable - Inspect . 41 V2x Module - Check . 41 Every 2000 Service Hours or 1 Year Dimensional Coverage - Verify . 41 DRAFT M0065690-01 i06552490 Dimensional Coverage - Verify SMCS Code: 7347 After 2000 hours or 1 year of service, ensure the machine measurements recorded in MineStar office are correct. Perform the machine measure up as described in Special Instruction, REHS9127 and compare the current results with the previously documented results in MineStar Office. Update values as needed. i06535635 Display - Clean SMCS Code: 7347-070 To maintain sufficient vision, the display must be inspected and/or cleaned for dust and debris at the beginning of each shift due to the environment. Use a soft, damp cloth with water only to clean the display. i06546889 GPS Accuracy - Check SMCS Code: 7348-535; 7490-535 After start up, ensure that the system is displaying a GPS accuracy in the Status and System Information windows. Verify that the level that is not reading fault . If the GPS mode is faulted, the Proximity Awareness system will not be active. Refer to Cat Detect Proximity Awareness User GuideUENR3246 for GPS troubleshooting information. i06546890 GPS Mast - Align SMCS Code: 7348-535; 7490-535 Improper operation of an access platform could result in injury or death. Operators must carry out their duties properly and follow all instructions and guidelines given for the machine and access platform. Note: When accessing the GPS antenna mast for cleaning of inspection, be sure to observe safe procedures for access. Maintain a three-point contact and or use a body harness. 41 Maintenance Section Dimensional Coverage - Verify Always inspect the condition of the GPS antenna mast and the condition of the GPS antenna mast mounting hardware before you operate the machine. Replace any parts that are damaged or worn before you operate the machine. Make sure that the mounting bolts are tight. i06547119 GPS Orientation - Adjust SMCS Code: 7348-025; 7490-025 After start up, ensure that the system is displaying the correct machine icon associated with your machine. Verify that the machine is positioned correctly relative to other machines or geographical features. If the orientation is incorrect, the Proximity Awareness system will not alarm correctly. To verify the system configuration, refer to Cat Detect Proximity Awareness User GuideUENR3246 for GPS configuration information. i07070734 V2x Module - Check SMCS Code: 1639-535 Check that the power and communication lights illuminate when powered ON . Check for physical damage to the module. Harness and Cable - Inspect SMCS Code: 1408-040; 4459-040 i07070757 Illustration 40 PL671 inspection g06214673 DRAFT 42 Maintenance Section Harness and Cable - Inspect Inspect for damaged wires or cables routed to the V2x modules. Refer to Illustration 40 . M0065690-01 DRAFT M0065690-01 Index A Audible Alarms ................................................ 32 Acknowledging Alarms ................................ 34 Alarm Types................................................. 32 Muting Alarms.............................................. 34 Proximity Alarming Filters............................ 32 B Before Operation..............................................11 Power ON/OFF.............................................11 D Dimensional Coverage - Verify........................ 41 Display - Clean ................................................ 41 Display Navigation........................................... 13 F Foreword ........................................................... 4 Literature Information .................................... 4 Maintenance .................................................. 4 Maintenance Intervals ................................... 4 Operation ....................................................... 4 Product Capacity ........................................... 4 Product Information ....................................... 4 Safety............................................................. 4 G General Information .......................................... 6 Detect Basics................................................. 6 Intended Use ................................................. 6 Object Detection System (If Installed) ........... 7 GPS Accuracy - Check.................................... 41 GPS Mast - Align............................................. 41 GPS Orientation - Adjust................................. 41 H Harness and Cable - Inspect........................... 41 I Important Safety Information............................. 2 43 Index Section Maintenance Interval Schedule....................... 40 Every 2000 Service Hours or 1 Year ........... 40 Every 8 Service Hours or Daily.................... 40 Maintenance Section....................................... 40 O Operation......................................................... 13 Operation Section.............................................11 Operator Utilities.............................................. 35 Adjusting Screen Brightness ....................... 38 Logging In .................................................... 35 Logging Out ................................................. 36 Marking a Hazard ........................................ 37 Pre-Operation Check................................... 36 Sending a Mayday Message ....................... 37 Unknown Login............................................ 36 P Plan Map Window ........................................... 17 Position of Other Machines ......................... 19 Position of Your Machine............................. 17 Zone Polygons............................................. 22 Product Information Section.............................. 6 S Safety ................................................................ 5 Operation ....................................................... 5 Safety Messages ........................................... 5 Safety Section ................................................... 5 Status Window ................................................ 16 Alarm Status Icon ........................................ 16 GPS Status Icons ........................................ 16 Miscellaneous Icons .................................... 16 Proximity Critical Icons ................................ 16 Radio Status Icon ........................................ 16 V2x Module Icons ........................................ 16 System Components......................................... 7 GPS Antenna................................................. 9 Optional Items................................................ 9 Touchscreen Monitor Display ........................ 9 V2x Module.................................................... 9 Wireless Radio (Customer Supplied) ............ 9 System Information Windows ......................... 15 M Main Screen .................................................... 14 T Table of Contents .............................................. 3 DRAFT 44 Index Section M0065690-01 Tool Button Display.......................................... 24 V V2x Module - Check ........................................ 41 Visual Proximity Alarming ............................... 25 Critical Proximity Alarm ............................... 29 Fundamentals.............................................. 25 High Priority Proximity Alarm....................... 27 Low Priority Proximity Alarm........................ 26 Unknown Machines ..................................... 31 DRAFT Product and Dealer Information Note: For product identification plate locations, see the section Product Identification Information in the Operation and Maintenance Manual. Delivery Date:
Product Information Model:
Product Identification Number:
Engine Serial Number:
Transmission Serial Number:
Generator Serial Number:
Attachment Serial Numbers:
Attachment Information:
Customer Equipment Number:
Dealer Equipment Number:
Dealer Information Name:
Address:
Branch:
Dealer Contact Phone Number Hours Sales:
Parts:
Service:
DRAFT M0065690 2018 Caterpillar All Rights Reserved 46 January 2018 CAT, CATERPILLAR, their respective logos, Caterpillar Yellow, and the POWER EDGE trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission. DRAFT
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2019-11-25 | 5745 ~ 5825 | NII - Unlicensed National Information Infrastructure TX | Class II Permissive Change |
2 | 2018-03-19 | 5850 ~ 5925 | TNB - Licensed Non-Broadcast Station Transmitter | Original Equipment |
3 | 5745 ~ 5825 | NII - Unlicensed National Information Infrastructure TX | ||
4 | 2402 ~ 2480 | DSS - Part 15 Spread Spectrum Transmitter | ||
5 | 2412 ~ 2462 | DTS - Digital Transmission System |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 3 4 5 | Effective |
2019-11-25
|
||||
1 2 3 4 5 |
2018-03-19
|
|||||
1 2 3 4 5 | Applicant's complete, legal business name |
Caterpillar, Inc.
|
||||
1 2 3 4 5 | FCC Registration Number (FRN) |
0022872246
|
||||
1 2 3 4 5 | Physical Address |
100 North East Adams Street
|
||||
1 2 3 4 5 |
Peoria, IL
|
|||||
1 2 3 4 5 |
Peoria, Illinois 61629
|
|||||
1 2 3 4 5 |
United States
|
|||||
app s | TCB Information | |||||
1 2 3 4 5 | TCB Application Email Address |
j******@metlabs.com
|
||||
1 2 3 4 5 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
1 2 3 4 5 |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
|||||
app s | FCC ID | |||||
1 2 3 4 5 | Grantee Code |
PQM
|
||||
1 2 3 4 5 | Equipment Product Code |
PL671
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 3 4 5 | Name |
W**** D******** B****
|
||||
1 2 3 4 5 | Title |
Certification Engineer
|
||||
1 2 3 4 5 | Telephone Number |
309-5********
|
||||
1 2 3 4 5 | Fax Number |
309-5********
|
||||
1 2 3 4 5 |
B******@cat.com
|
|||||
app s | Technical Contact | |||||
1 2 3 4 5 | Firm Name |
Caterpillar Inc.
|
||||
1 2 3 4 5 | Name |
J******** C********
|
||||
1 2 3 4 5 | Physical Address |
PO Box 610
|
||||
1 2 3 4 5 |
Mossville, 61552
|
|||||
1 2 3 4 5 |
Mossville, Illinois 61552
|
|||||
1 2 3 4 5 |
United States
|
|||||
1 2 3 4 5 | Telephone Number |
309-5********
|
||||
1 2 3 4 5 |
C******@cat.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 3 4 5 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 3 4 5 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 3 4 5 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 3 4 5 | Equipment Class | NII - Unlicensed National Information Infrastructure TX | ||||
1 2 3 4 5 | TNB - Licensed Non-Broadcast Station Transmitter | |||||
1 2 3 4 5 | DSS - Part 15 Spread Spectrum Transmitter | |||||
1 2 3 4 5 | DTS - Digital Transmission System | |||||
1 2 3 4 5 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Digital Transmission System | ||||
1 2 3 4 5 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | Yes | ||||
1 2 3 4 5 | No | |||||
1 2 3 4 5 | Modular Equipment Type | Does not apply | ||||
1 2 3 4 5 | Purpose / Application is for | Class II Permissive Change | ||||
1 2 3 4 5 | Original Equipment | |||||
1 2 3 4 5 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 3 4 5 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 3 4 5 | Grant Comments | Power output listed is conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter Device. This device supports MIMO system. The device has 20MHz and 40MHz bandwidth. | ||||
1 2 3 4 5 | Output Power listed is combined-conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and not be co-located with any other transmitters except in accordance with multi-transmitter product procedures. The device uses MIMO system. | |||||
1 2 3 4 5 | Power output listed is combined conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter Device. This device supports MIMO system. The device has 20MHz and 40MHz bandwidth. | |||||
1 2 3 4 5 | Output Power listed is peak conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and not be co-located with any other transmitters except in accordance with multi-transmitter product procedures. | |||||
1 2 3 4 5 | Output Power listed is combined-conducted. The device has 20MHz and 40MHz bandwidth. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and not be co-located with any other transmitters except in accordance with multi-transmitter product procedures. The device uses MIMO system. | |||||
1 2 3 4 5 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 3 4 5 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 3 4 5 | Firm Name |
Eurofins MET Laboratories, Inc.
|
||||
1 2 3 4 5 | Name |
J******** F********
|
||||
1 2 3 4 5 | Telephone Number |
41094********
|
||||
1 2 3 4 5 | Fax Number |
41035********
|
||||
1 2 3 4 5 |
j******@metlabs.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15E | CC | 5180 | 5240 | 0.0644 | |||||||||||||||||||||||||||||||||||
1 | 2 | 15E | CC MO | 5745 | 5825 | 0.103 | |||||||||||||||||||||||||||||||||||
1 | 3 | 15E | CC MO ND | 5260 | 5320 | 0.048 | |||||||||||||||||||||||||||||||||||
1 | 4 | 15E | CC MO ND | 5500 | 5700 | 0.045 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 90,95L | MO | 5850 | 5925 | 0.1035 | 9.556 ppm | 9M00G1D | |||||||||||||||||||||||||||||||||
2 | 2 | 90,95L | MO | 5850 | 5925 | 0.1035 | 9.556 ppm | 9M00W1D | |||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
3 | 1 | 15E | CC | 5180 | 5240 | 0.0644 | |||||||||||||||||||||||||||||||||||
3 | 2 | 15E | CC MO | 5745 | 5825 | 0.103 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
4 | 1 | 15C | CC | 2402.00000000 | 2480.00000000 | 0.0087000 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
5 | 1 | 15C | CC MO | 2412 | 2462 | 0.0406 | |||||||||||||||||||||||||||||||||||
5 | 2 | 15C | CC | 2402 | 2479 | 0.0082 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC