FCC ID: CN292820 IR LRM2 2400 MHz Module

IR LRM2 Radio Module Document p/n: 9S02-9282-A001 Rev.A Introduction Product Development IR LRM2 Radio Module

(2MOD-9282-xxxx) Document p/n: 9S02-9282-A001 Rev.A CONFIDENTIALITY NOTICE This correspondence and all information contained within are the exclusive, confidential and proprietary property of Cattron North America Inc. it is not to be reproduced, nor is it or any portion of it to be used by or disclosed to any other individual or legal entity, without the prior, written approval of Cattron North America Inc. Furthermore, the information contained within this correspondence is also to be handled in accordance with any and all confidentiality agreements between Cattron North America Inc. and the receiver or user of this information. 2022 Cattron North America Inc. IR LRM2 Radio Module Document p/n: 9S02-9282-A001 Rev.A Introduction Revision History Date Revision Description Signature / Date 2022-10-15 A Initial draft Prepared H. Lin Verified Approved Prepared Verified Approved Prepared Verified Approved Prepared Verified Approved IR LRM2 Radio Module Document p/n: 9S02-9282-A001 Rev.A Introduction Table of Contents 1. INTRODUCTION ............................................................................................................................................1-6 1.1 1.2 1.3 1.4 1.5 PURPOSE ..........................................................................................................................................................1-6 SCOPE ..............................................................................................................................................................1-6 APPLICABILITY ................................................................................................................................................1-6 DEFINITIONS, ACRONYMS ...............................................................................................................................1-6 1.4.1 Definitions ..............................................................................................................................................1-6 1.4.2 Acronyms ................................................................................................................................................1-6 REFERENCES ....................................................................................................................................................1-6 2. FEATURES SUMMARY .................................................................................................................................2-1 3. HOST INTERFACE DEFINITION ................................................................................................................3-2 3.1 3.2 PINS ASSIGNMENT ...........................................................................................................................................3-2 SIGNALS DESCRIPTION ....................................................................................................................................3-3 4. FUNCTIONAL DESCRIPTION .....................................................................................................................4-5 4.1 4.2 4.3 OVERVIEW.......................................................................................................................................................4-5 IR LRM2(2MOD-9282) Radio ...............................................................................................................4-5 4.1.1 4.1.2 Data Communication Model & Definitions ............................................................................................4-5 TELEGRAM TRANSMISSION..............................................................................................................................4-6 TELEGRAM RECEPTION ...................................................................................................................................4-6 5. IR LRM2 CONFIGURATION CONCEPT ...................................................................................................5-7 5.1 5.2 5.1.1 5.1.2 5.1.3 CONSOLE INTERFACE ......................................................................................................................................5-7 Write command ...................................................................................................................................5-7 Read command ....................................................................................................................................5-7 Help command ....................................................................................................................................5-7 STAND-ALONE TEST MODE .............................................................................................................................5-7 IR LRM2 Radio Module Document p/n: 9S02-9282-A001 Rev.A Introduction 92820TRX module meets Part 15 of the FCC rules and regulations. Compliance with the labeling requirements, FCC notices is required. In order to comply with FCC Certification requirements, the Original Equipment Manufacturer (OEM) must fulfill the following requirements. 1. The system integrator must place an exterior label on the outside of the final product housing the 92820 TRX Module. The figure below shows the contents that must be included in this label. 2. 92820TRX modules may only be used with the antennas that have been tested and approved for use with the module. Labeling Requirements The OEM must make sure that FCC labeling requirements are met. This includes a clearly visible exterior label on the outside of the final product housing that displays the contents shown in below. WARNING: The 92820TRX modules have been tested by the FCC for use with other products without further certification (as per FCC Section 2.1091). Changes or modifications to this device not expressly approved by Cattron North America Inc. could void the users authority to operate the equipment. NOTICE: OEMs must verify the final product complies with unintentional radiators (FCC Section 15.107 and 15.109) before providing a declaration of conformity for their final product to Part 15 of the FCC Rules. NOTICE: The 92820TRX modules have been certified for mobile and fixed radio applications. If the module will be used for portable applications, the device must undergo SAR testing. RF Exposure WARNING: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. NOTICE: The preceding statement must be included as a CAUTION statement in OEM product manuals in order to alert users of FCC RF Exposure compliance. 92820TRX is designed for use in countless wireless applications requiring long range communications with low energy consumption. To ensure that the final product complies with the all of the regulatory requirements for the Modular Grant the following integration instructions should be followed. 92820TRX is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end-user has no manual instructions to remove or install the module. IR LRM2 Radio Module Document p/n: 9S02-9282-A001 Rev.A Introduction FCC Part 15.19 Warning Statement THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. FCC Part 15.21 Warning Statement NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. FCC Part 15.105(b) Warning Statement- (ONLY Required for 15.109-JBP devices) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. IC RSS-GEN, Sec 8.4 Warning Statement ENGLISH:

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. FRENCH:

Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Only the following authorized antennas or the antenna gain less than highest gain antenna for each band may be used with the equipment:

2400MHz wave dipole antenna (SPDA17RP2400/5900, 2dBi);

2400MHz PCB PIFA antenna, -3dBi IR LRM2 Radio Module Document p/n: 9S02-9282-A001 Rev.A Introduction 1. Introduction 1.1 Purpose A new family of RF module, the LRM2 family, is being developed by Cattron North America Inc. This family is employing Silicon Labs EFR32FG13 Flex Gecko SoC (System On Chip), which is including a high performance Radio transceiver and a high performance Micro-Controller Unit. 1.2 Scope This document describes the host interface signal definitions, timings, operation mode, available functionalities, and provide details about its integration to Unity products. This document does not cover RF specifications or power supply specifications. 1.3 Applicability Applies to IR LRM2 family members, P/N 2PCA-9282-xxxx 1.4 Definitions, Acronyms 1.4.1 Definitions 1.4.2 Acronyms IR LRM2 MCU SoC OCU 1.5 References Radio Module Machine Control Unit System-On-Chip Operator Control Unit

[1] Schematic Drawing for LRM2, Cattron P/N 9D02-9282-A001

[2] Unity RF Telegrams Format, Cattron P/N 9S01-7640-A101

[3] LRM2 Radio Module Configuration Registers Specifications, Cattron P/N 9S02-8969-A002 IR LRM2 Radio Module Document p/n: 9S02-9282-A001 Rev.A Features Summary 2. Features Summary The IR LRM2 is designed to replace Remtron products with less cost and improved performance. Its host interface is compatible with previous LRM(2PCA-7954-xxxx) series. Direct electrical compatibility to LRM (2PCA-7954-xxxx) interface On-board wireless SoC The interface is controlled by an on-board Silicon Labs EFR32FG13 SoC. The EFR32FG13 Flex Gecko SoC includes both a high-performance radio transceiver and a high performance, low power Micro-Controller. Minimum buffers/Minimum Delay IR LRM2 firmware is implemented to provide a almost transparent operation; transmission and reception delays are kept to a minimum Support for different Modulation modes The IR LRM2 family is designed to support multiple different RF Modulations (2FSK and 4FSK), which is transparent to Host firmware. These different aspects are covered in the rest of this document. IR LRM2 Radio Module Document p/n: 9S02-9282-A001 Rev.A Host Interface Definition 3. Host Interface Definition 3.1 Pins Assignment Board to board connector Pin Details J1 Pin number 1 3 5 7 9 11 13 15 17 19 Signal name GND TDI-RF MASTER-CTRL-US1-RX-M GND I2C0-SDA-RF I2C0-SCL-RF GND RFIO-1-M BOOT-EN/RFIO-0-M GND Pin number 2 4 6 8 10 12 14 16 18 20 Signal name GND nRESET-RF RFIO-2-M MASTER-DATA-US0-TX-M RFIO-3-M TDO-RF MASTER-DATA-US0-RX-M TMS/SWDIO-RF TCK/SWDCLK-RF MASTER-CTRL-US1-TX-M Pin number 1 3 5 7 9 11 13 15 17 19 Signal name GND nRESET-M nRESET-S BOOT-EN/RFIO-0-S SLAVE-DATA-US0-RX-S SLAVE-CTRL-US1-RX-S SLAVE-DATA-US0-TX-S SLAVE-CTRL-US1-TX-S READY GND J5 Pin number 2 4 6 8 10 12 14 16 18 20 Signal name GND 3.3V 3.3V GND REV_AN RFIO-1-S ANT_SEL FWD_AN READY (For PA_EN) GND Table 3.1 Host Interface pins assignment IR LRM2 Radio Module Document p/n: 9S02-9282-A001 Rev.A 3.2 Signals Description Host Interface Definition Net Name TCK/SWDCLK-RF TMS/SWDIO-RF TDO-RF TDI-RF MASTER-DATA-US0-TX-M MASTER-DATA-US0-RX-M RFIO-2-M RFIO-3-M 3.3V 38.4MHz crystal Oscillator nRESET-RF Sub GHz RF Output Sub GHz RF Input GND GND GND 2G4RF_IOP PAVDD nRESET-M nRESET-S BOOT-EN/RFIO-0-S SLAVE-DATA-US0-RX-S SLAVE-DATA-US0-TX-S SLAVE-CTRL-US1-RX-S SLAVE-CTRL-US1-TX-S TCXO_EN TX/nRX READY REV_AN RFIO-1-S 3.3V ANT_SEL FWD_AN General Description GPIO (5V) GPIO (5V) GPIO (5V) GPIO (5V) GPIO (5V),UART_RX for Master data signals GPIO (5V), UART_TX for Master data signals GPIO (5V), RFIO-2_Master GPIO (5V), RFIO-3_Master Radio Power Supply High Frequency Crystal input, 38.4MHz crystal Oscillator High Frequency Crystal output, 38.4MHz crystal Oscillator Reset input, active low, nReset_Radio (Input from JTAG connector) Sub GHz Differential RF output, positive path Sub GHz Differential RF output, negative path Sub GHz Differential RF input, positive path Sub GHz Differential RF input, negative path Radio Ground Power Amplifier (PA) voltage regulator VSS 2.4 GHz Differential RF input/output, negative path 2.4 GHz Differential RF input/output, positive path Power Amplifier (PA) voltage regulator VDD input nRESET_M (Reset output for Master controller) nRESET_S (Reset output for Slave controller) RFIO-0_Slave UART_TX for slave data signals UART_RX for slave data signals UART_TX for Slave control signals UART_RX for Slave control signals GPIO for TCXO_EN GPIO (5V), TX/nRX (GPIO to enable RF switch#01 & 02) GPIO for GREEN LED. Multiplexed with READY (GPIO output) REV_AN RFIO-1_Slave Analog power supply ANT_SEL (GPIO to enable RF switch#03 which will be located on MCU board) GPIO for RED LED. Multiplexed with FWD_AN (For power amplifier. It is not required in our design. Just provision for cattron team) Host Interface Definition IR LRM2 Radio Module Document p/n: 9S02-9282-A001 Rev.A GND NC 3.3V 3.3V GND with decoupling cap 3.3V BOOT-EN/RFIO-0-M RFIO-1-M I2C0-SCL-RF I2C0-SDA-RF MASTER-CTRL-US1-RX-M MASTER-CTRL-US1-TX-M Voltage regulator VSS Kept it NC 3.3V Supply 3.3V Supply Decouple output for on-chip voltage regulator 3.3V Supply RFIO-1_Master I2C0_SCL I2C0_SDA UART_TX for Master control signals UART_RX for Master control signals Table 3.2 - Host Interface signals description IR LRM2 Radio Module Document p/n: 9S02-9282-A001 Rev.A Functional Description 4. Functional Description 4.1 Overview 4.1.1 IR LRM2(2MOD-9282) Radio

. Figure 4.1 IR LRM2 Design The Silicon Labs ERF32FG13 SoC is located between the host interface and the RF interface, providing decoupling between host and RF interface. The EFR32FG13 SoC has sufficient buffer space for one telegram. As shown later, telegram processing is defined to minimize delays, so to provide a transparent-like behavior. 2.4-GHz will be supported. 4.1.2 Data Communication Model & Definitions The communication model defines some of the terminology used in the rest of this document. Figure 4.2 - Data communication model HostLRM Radio ModuleHost Data BufferTx/RxTransmit Telegram FramesReceive Telegram FramesRF packetsLRM Host InterfaceLRM RF Interface IR LRM2 Radio Module Document p/n: 9S02-9282-A001 Rev.A Functional Description

- The IR LRM2 Radio Module is used to communicate telegrams between hosts. In Unity context, hosts are OCU and MCU CPU boards. The IR LRM2 has two interfaces: a Host Interface and a RF Interface.

- Transmit and Received Telegrams are relayed through the IR LRM2 Host Data Buffer. This buffer is capable to hold only one telegram at a time. The purpose of this buffer is to relax host timings requirements, and to allow decoupling between Host Interface and RF Interface data rates.

- Telegrams sent/received on the Host Interface and RF interface are encapsulated into frames to improve synchronization.

- The IR LRM2 does not perform any processing on the telegrams content; it controls only the frames overhead. 4.2 Telegram Transmission Transmit frames have two fields:

- Telegram length (number of bytes). The length is used by the CPU to control the transmission process.

- Telegram (maximum 254 bytes). The content of the telegram is defined by the application. For Unity application, this is the Unity Telegram beginning with the Scrambling byte, the TID and terminated with the 16bits CRC, as defined in ref [2]. Figure 4.3 - Transmit Telegram frame format 4.3 Telegram Reception Each RF packet received by the LRM2 is sent to the host interface, followed by its RSSI. Also, in order to ensure receive telegram frame synchronization (i.e. unambiguous detection of the start of the frame), the frame is encapsulated according to SLIP framing. SLIP framing is very simple to decode. It is described in section Error!

Reference source not found.. Receive frame fields are:

SOF (Start-of-Frame character). This is part of SLIP encapsulation.

- Length of the Telegram field (number of bytes), not counting RSSI fields and any additional control characters introduced for SLIP encapsulation.

- Telegram (maximum 254 bytes). The content of the telegram is defined by the application.

- RSSI: Received signal strength for this frame. RSSI is an 8 bits integer value, expressed in dBm. Range;-128 to

+127 dBm. Figure 4.4 - Receive Telegram frame format Length1 byteTelegramLength bytesLength1 byteTelegramLength bytesRSSISOF1 byte1 byte IR LRM2 Radio Module Document p/n: 9S02-9282-A001 Rev.A IR LRM2 Configuration Concept 5. IR LRM2 Configuration Concept All IR LRM2 configuration and status parameters are accessible through addressable registers.

- All parameters can be read and written only in CONFIG mode. The definition of the configuration registers is given in reference [3]. This section addresses the basic description of all these three methods. 5.1 Console Interface The Sub-GHz serial interface configuration port is enabled by asserting !CONFIG signal; the serial interface is automatically reconfigured in asynchronous mode, running at 38400bps, 8N1. All ASCII strings received are interpreted as configuration commands. This mode is particularly useful for stand-alone testing, when the unit can be controlled from a PC or by an operator/tester using a terminal emulation program. 5.1.1 Write command wrCmd register value , where:

wrCmd = write command. w or wr can be used and are equivalent register = register identification. Can use the register name or register address value = value to be written, in decimal or hexadecimal format. Hexadecimal values are preceded by 0x 5.1.2 Read command rdCmd reg where:

rdCmd= read command. r or rd can be used and are equivalent reg

= register identification. Can use the register name or register address 5.1.3 Help command helpCmd where:

helpCmd= help command. h, help or ? can be used and are equivalent. The IR LRM2 responds with the list off all available configuration registers. 5.2 Stand-Alone Test Mode The IR LRM2 can be operated in stand-alone mode for production/service tests. In this case, only a 3.3VDC supply is needed, and a RS232/TTL transceiver (like Cattron FLASHBOX) to connect to a PC serial port. IR LRM2 Radio Module Document p/n: 9S02-9282-A001 Rev.A IR LRM2 Configuration Concept Figure 5.1 - LRM2 connection for stand-alone operation The IR LRM2 will support several built-in test modes to ease testing from a PC. For example a. Bluetooth Tests

- By using Silicon Labs application, Wireless Gecko, the Bluetooth channel, transmit power level, data speed could be adjusted. 21LRM, host interface26RXDTXD25!CONFIG3V3GND2722RS232 - TTL transceiver(ex: Cattron FLASHBOX)3.3VDCRS232PC, running automated testprogram, or ANSI terminalemulation software*Note: The LRM !RX_EN, !TX_EN and !RESET all have internal pull-ups, so they can be left unconnected.

D C B A 1 2 3 4 5 6 USE LOGO GRAPHIC FILE 9D11-8993-A002 Mfd by Cattron North America, Inc. Warren, OH 44483-2254 USA This unit contains radio module:

FCC ID:

IC:

M/N:

Freq:

CN292820 1007A- 92820 92820 TRX 2404-2480 MHz 3LBL-7707-A215 IR LRM2, 2400MHz r e h t o y n a o t d e s o c s l i d r o y b d e s u e b o t t i f o n o i t r o p y n a r o t i s i r o n

, d e c u d o r p e r e b o t t o n s i t I

. n o r t t a C f o y t r e p o r p y r a t e i r p o r p d n a l ia t n e d i f n o c

, e v s u c x e e h t l i 1 2 DRAWING NUMBER:

9D08-7707-A215 4 3 DESCRIPTION:

LABEL, APPROVAL, M, L, IR LRM2 2400MHZ 5 REV. B SHEET 2 OF 2 6 a m r o n f i l l a d n a t n e m u c o d s h T i e r a i n h t i w d e n i t a n o c n o i t y it l a i t n e d i f n o c l l a d n a y n a h t i w e c n a d r o c c a n i d e l d n a h e b o t o s l a s i e c n e d n o p s e r r o c s i h t n i h t i w d e n i a t n o c n o i t a m r o f n i e h t

, e r o m r e h t r u F

. n o r tt a C f o l a v o r p p a n e t t i r w

, r o i r p e h t t u o h t i w

, ty i t n e l a g e l r o l a u d v d n i i i D C B A

. 9 1 0 2 n o r t t a C t h g i r y p o C

. n o i t a m r o f n i is h t f o r e s u r o r e v e c e r i e h t d n a n o r t t a C n e e w t e b ts n e m e e r g a

27th October

, 2022 Federal Authorization Communications and Evaluation Commission Division

@ CATTRON'"

North America Inc. Cattron 655 N River Road NW STE A Warren OH 44483-2254 Tel: (826) 674 9780 806 0019 Fax:(234) www.cattron.com USA Confidentiality Request regarding application for certification of FCC ID: CN292820 Pursuant treatment to Sections of information accompanying this application as outlined below:

0.457 and 0.459 of the Commission's Rules, we hereby request confidential Exhibit Type Block Diagram Schematics Operation Parts List Description File Name IR-LRM2-CN292820-BlkDia.pdf IR-LRM2-CN292820-Schem. pdf IR-LRM2-CN292820-OpDes.pdf IR-LRM2-CN292820-PartsLst.pdf The above materials The public public. disclosure to its competitors. benefits contain trade secrets of these materials and proprietary information may be harmful to the applicant not customarily and provide released to the unjustified The applicant all accompanying that pursuant documentation understands to Section 0.907 of the Rules, disclosure of this application and will not be made before the date of the Grant for this application. Pursuant confidential to DA04-1705 treatment public notice, June 15, 2004 of the Commission's this application we also request for 180 days as outlined temporary below:

accompanying of information Type Exhibit Test Set up photos Manual File Name Test Setup Photos.pd[

IR-LRM2-CN292820-Manual.pdf Sincerely, David Stagg Program Cattron Manager North America Inc. Cattron North America Inc. Conf-letter-long-short-tenn-CN292820.doc

November 16th, 2022 Reference:

Applicant:

Equipment:

Model #:

FCC ID:

IC:

Cattron North America Inc. 2400MHz Transceiver Device 92820 TRX CN292820 1007A-92820 Cattron North America Inc. 655 N River Road NW STE A Warren OH 44483-2254 USA Tel: (826) 674 9780 Fax:(234) 806 0019 www.cattron.com With regard to the Part 15 requirements for modular approval, Cattron North America Inc. would make the following observations with regard to the numbered requirements for the RF module: 92820 TRX (FCC ID: CN2 92820, IC ID:1007A-92820):

I. The radio elements must have the radio frequency circuitry shielded. Complies, the module has metallic shielding cover. II. The module must have buffered modulation/data inputs.-

The equipment into which this module is installed is exclusively designed and manufactured by and for Cattron North America Inc., the equipment is of our own design and the data is carefully controlled to maintain FCC compliance. III. The module must contain power supply regulation on the module.-

The equipment into which this module is installed is exclusively designed and manufactured by and for Cattron North America Inc. and all have their own regulated and monitored 3.3V supply voltage, excursions of more than +/-10% result in equipment shut down. IV. The module must contain a permanently-attached antenna, or contain a unique antenna connector, and be marketed or operated only with specific antenna(s)-

The antenna requirements are met by having third party tested the integral and variants of external antennas as part of the FCC submission. V. The module must demonstrate compliance in a stand-alone configuration.-

The modular transmitter has been tested in the defined stand-alone configuration. VI. The module must be labeled with its permanently fixed FCC ID label, or use an electronic display.-

The Labeling requirements of the modular approvals will be followed, as previously stated the module is only incorporated into Cattron North America Inc. equipment, the label will be installed on the outside of the equipment into which it is incorporated. VII. Operating parameters are controlled within system requirements specifications, these define the specific voltage tolerance, data rate, deviation and Duty Cycle. VIII. RF exposure limits are maintained by, a) Limiting power and duty cycle according to the test report. b) Posting warnings in the operations manual to warn of the possible harmful effects of human exposure to radiation. Cattron North America Inc. FCC-ISED-Declare-letter-IR-LRM2-2400MHz.doc

ks CATTRON Cattron North America Inc. 655 N River Road NW STE A Warren OH 44483-2254 USA October 27", 2022 Tel: (826) 674 9780 Fax: (234) 806-0019 Federal Communications Commission www.cattron.com Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: FCC Application for FCC ID: CN292820 and IC: 1007A-92820 To Whom It May Concern:

We, the undersigned, hereby authorize Mrs. Sharon Hoffman at Timco Engineering Inc. on our behalf, to apply to the Federal Communications Commission on our equipment (FCC ID: CN292820, IC:

1007A-92820). Any and all acts carried out by Mrs. Sharon Hoffman on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, David Stagg Program Manager Cattron North America Inc. Cattron North America Inc. Page | of | FCC-Power-Attorney2022 10-CN29282.doc