FCC Regulatory Information for the Module This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Information to be supplied to the OEM or Host Integrator The OEM/Host Integrator shall be responsible for ensuring that the end-user has no manual instructions to remove or install module and the FCC compliance requirement of the end product, which integrates this module. 1. Applicable rules:
This module is certified pursuant to two Part 15 rules sections (15.247). 2. Specific operational use conditions and antenna list:
a) This module is restricted to installation in products for use only in mobile and fixed applications. b) The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. c) The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter. d) OEM integrator has be limited the operation channels in channel 1-11 for 2.4GHz band. e) This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated. Ant. Port Brand Model Name Antenna Type Gain (dBi) A B 1 2 1
-
-
ALO140-052030 ALC140-051021-A PIFA Print 3 3 3 Ant. Port Brand Model Name Antenna Type Gain (dBi) 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 C D E F G H I J
-
-
-
-
ALC140-052030-A ALC160-051020-000000 ALC160-051021-000000 GY196HT625-001 GY196HT625-002 ALO160-052030-A ALO160-052030-A Master Wave 660023500G WNC WNC Sevio 81XCBB15.G01 81XCBB15.G02 NTW01 PIFA Print Print PIFA Dipole PIFA PIFA Dipole 3 3 3 3.33 3.76 1.73 1.84 3.54 3.41 2.38 2.38 1.28 1.28 1.18 1.18 2.2 2.2 Note: Other types of antennas and/or higher gain antennas shall only be authorized by Permissive Change procedures 3. RF exposure considerations The end product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC RF exposure guideline. Mobile: (2.1091) (b) A mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 cm is normally maintained between the transmitters radiating structure(s) and the body of the user or nearby persons. Per 2.1091(d)(4) In some cases (for example, modular or desktop transmitters), the potential conditions of use of a device may not allow easy classification of that device as either Mobile or Portable. In these cases, applicants are responsible for determining minimum distances for compliance for the intended use and installation of the device based on evaluation of either specific absorption rate (SAR), field strength, or power density, whichever is most appropriate. Note: If the final host/end product is intended for use as a portable device, the host manufacturer is responsible for separate approvals for the SAR requirements from FCC Part 2.1093. 4. Information on test modes and additional testing requirements 1. This module is restricted to integration into hosts for indoor use only. 2. This module has been approved under stand-alone configuration. 3. OEM integrator has be limited the operation channels in channel 1-11 for 2.4GHz band. 4. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations. 5. The information on how to configure test modes for host product evaluation for different operational conditions for a stand-alone modular transmitter in a host, versus with multiple, simultaneously transmitting modules or other transmitters in a host can be found at KDB Publication 996369 D04. if applicable additional equipment 5. Additional testing, Part 15 Subpart B disclaimer Appropriate measurements (e.g. 15B compliance) and authorizations (e.g. SDoC) of the host product to be addressed by the integrator/manufacturer. This module is only FCC authorized for the specific rule parts 15.247 listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host product as being Part 15 Subpart B compliant. Manual Information to Be Supplied to the End User by the OEM or Host Integrator Class B Device Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Label Compliance Information to be mandatory to affix to the End Product The host product shall be labeled in an external, visible permanent area with the following:
"Contains TX FCC ID: PANWM8192EU " or Contains Transmitter Module FCC ID: PANWM8192EU The end product shall bear the following 15.19 statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Note: If the labelling area is considered too small and therefore it is impractical (smaller than the palm of the hand) to display the compliance statement, then the statement may be placed in the user manual or product packaging. Industry Canada statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. Lappareil ne doit pas produire de brouillage;
2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This radio transmitter [IC: 6225A-WM8192EU] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Brand Ant. 1 Sevio Antenna Type Model Name Gain (dBi) NTW01 Dipole 2.2 Le prsent metteur radio [IC: 6225A-WM8192EU] a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'metteur. Ant. 1 Antenna Type Brand Sevio Model Name Gain (dBi) NTW01 Dipole 2.2 IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20cm de distance entre la source de rayonnement et votre corps OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the IC authorization is no longer considered valid and the IC No. cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate IC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains transmitter module IC:
6225A-WM8192EU. Contient le module d'mission IC: 6225A-WM8192EU The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online. This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit tre installe de telle sorte qu'une distance de 20cm est respecte entre l'antenne et les utilisateurs, et 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. IMPORTANT NOTE for OEM integrator:
This module is intended for OEM integrator. The OEM integrator is still responsible for 1. ensuring that the end-user has no manual instructions to remove or install module 2. the ISED compliance requirement of the end product, which integrates this module. 3. Appropriate measurements and if applicable additional equipment authorizations of the host device to be addressed by the integrator/manufacturer. 4. The separate approval is required for all other operating configurations, including portable configurations and different antenna configurations The transmitter module may not be co-located with any other transmitter or antenna. Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. CAN ICES-3 (B)/NMB-3(B) The Country Code Selection feature is disabled for products marketed in the US/Canada For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux tats-Unis / Canada du march, seul le canal 1 11 peuvent tre exploits. Slection d'autres canaux n'est pas possible.