Die Line File:
Die Line File:
IDL_TM0007P_T-MOBILE 10W WIRELESS CHARGING PAD QIG-FCC IDL_TM0007P_T-MOBILE 10W WIRELESS CHARGING PAD QIG-FCC Artwork File:
Artwork File:
INS_TM0022P-BLK_8820-01593_RevA00_Studio_Wireless_Charging_Stand_10W_Insert_TMO_v2 REV REV A A 00 00 DIE LAYOUT DIE LAYOUT I N N O V A T I O N C R E A T I V E G R O U P INS_TM0022P-BLK_8820-01593_RevA00_Studio_Wireless_Charging_Stand_10W_Insert_TMO_v2 TM0022P-BLK P#
8820-01593 REV FILE NAME SKU#
DESIGNER Anny DATE 12/10/21 4:20 PM VERSION X X X X X A00 02 QIG/FCC Statement QIG/FCC Statement 70 gsm woodfree paper 70 gsm woodfree paper Wireless Charging Stand 10W SKU/MODEL: TM0022P 1 2 1 Its recommended to use the provided wall adapter & Type C cable to power your wireless charging stand. 2 With the screen facing out, place your Qi-enabled smartphone vertically so that it aligns with the center of the stand. Or, place it horizontally centered on the front-side stand holder. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the distance between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instructions as documented in this manual. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. See T-Mobiles Terms and Conditions (including arbitration provision) at T-Mobile. com, for additional information, and restrictions and details. T-Mobile and the magenta color are registered trademarks of Deutsche Telekom AG. 2022 T-Mobile USA, Inc. Printed in Vietnam. 8820-01593 Rev. A00 FRON T FRON T 3 4 If device is placed correctly in the middle and charging, the light will be solid white. If device is not placed correctly in the middle, it will not charge and the light will be off. Do not place foreign objects on the stand, the light will be solid red for certain objects. iPhone 13/12 mini 4 Do not place magnetic mounts, metal cases, keys, coins, or other objects between your phone and the charger. It might reduce performance or damage magnetic strips or RFID chips like those found in some credit cards, security badges, and passports. If your case holds any of these sensitive items, remove them before charging or make sure they arent between the back of your phone and the charger. The stand has sensors which detects objects which are not supposed to be placed to prevent the charger emitting unnecessary power and heat that could damage your smartphone and other heat-
sensitive items. Safety Instructions:
1. Please read these instructions before using the device to ensure safe and proper use. 2. Connect the wall adapter of the wireless charging stand into a socket outlet that is close by and is easy to disconnect from the source. 3. Use indoors and in a dry location only; keep away from wet or damp locations. 4. Keep wireless charging stand and wall adapter away from any liquids or moisture. 5. Unplug the wireless charging stand when unused for long periods of time. 6. Do not store your device in very hot or very cold areas. It is recommended to use your device at room temperatures. 7. Caution: If you experience problems with the wireless charging stand, please discontinue use, unplug the wall adapter of the wireless charging stand from the AC socket, and contact T-Mobile for assistance. 8. Do not use if visible defects are observed on the wireless charging stand or wall adapter. Do not attempt to service or disassemble. 411/32 411/32
[110.109]
[110.109]
3 LED light will indicate charging status as summarized in the table below. FCC Statement Status Start-up (Power On) Charging Fully Charged Insufficient from Power Source FOD (Foreign object detected) Temperature Fault Power Source Error Standby LED Solid White 3 Seconds Solid White Solid White Intermittent White Light Solid Red Solid Red Solid Red None/Off DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We, T-Mobile, of 12920 SE 38th St., Bellevue, WA 98006, Tel:+1(877)453 1304, declare under our sole responsibility that the product, to which this declaration relates, complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Federal Communications Commission Interference Statement BACK BACK 33/4 33/4
[95.250]
[95.250]
111/4 111/4
[285.750]
[285.750]
Business Unit:
Business Unit:
Core Core Program Manager:
Program Manager:
Packaging Engineer:
Packaging Engineer:
Matthew Duffy Matthew Duffy Retail Outside Dimension (Including Hang Tab) Retail Outside Dimension (Including Hang Tab) L x W x D (in):
L x W x D (in):
L x W x D (mm):
L x W x D (mm):
DIE/MATERIAL SPECS:
DIE/MATERIAL SPECS:
Material:
Material:
Please refer to drawing Please refer to drawing Blank Size (in):
Blank Size (in):
Blank Size (mm):
Blank Size (mm):
This dieline works for following skus (if any):
This dieline works for following skus (if any):
Unit:
Unit:
IN/MM IN/MM PRINT SIDE PRINT SIDE Side Shown:
Side Shown:
Flute/Grain:
Flute/Grain:
vertical vertical Tolerance:+/- 1/32" - 0.8mm Tolerance:+/- 1/32" - 0.8mm Drawing Scale 1:1 Drawing Scale 1:1 RELEASE DATE: 08/02/2019 RELEASE DATE: 08/02/2019 DIELINE:
DIELINE:
Intermediate Intermediate THIS DOCUMENT & THE INFORMATION THIS DOCUMENT & THE INFORMATION IN IT ARE THE CONFIDENTIAL PROPERTY IN IT ARE THE CONFIDENTIAL PROPERTY OF BELKIN INTERNATIONAL AND MUST OF BELKIN INTERNATIONAL AND MUST NOT BE COPIED, REPRODUCED OR USED NOT BE COPIED, REPRODUCED OR USED IN ANY MANNER WITHOUT THE WRITTEN IN ANY MANNER WITHOUT THE WRITTEN CONSENT OF BELKIN CORPORATION. CONSENT OF BELKIN CORPORATION. IT MUST BE RETURNED UPON REQUEST IT MUST BE RETURNED UPON REQUEST DO NOT PRINT DO NOT PRINT DIE LINES, PRINTERS NOTES DIE LINES, PRINTERS NOTES PRINT SPECS:
PRINT SPECS:
Color Plates:
Color Plates:
Finish:
Finish:
Notes:
Notes: