2005 NEW PRODUCT PROPOSAL CPX 2350 Description: 2 channel alarm with dual polarity door locks, trunk/hatch release, dual stage shock sensor, starter disable output, 20 watt single tone siren, mini-transmitters. B.O.M.:
1- Main Unit 2- mini-transmitters at 433.9 MHz. 1- 20 watt six tone siren (SN3541 20 watt single tone- Same as Auto Page standard) 1- dual zone shock sensor 1- valet/override switch 1- LED with white plug 1- 3-pin plug for dual polarity door lock/unlock outputs (same as Auto Page standard) 1- Multi-pin alarm wire harness 1- 5-pin standard power harness 1- 2-color box (Auto Page to provide the design) 1- Manuals for Operations and Installation (English and Spanish) 1. 500 milli-amp output for starter disable (ground while armed) 2. 500 milli-amp output for door lock/unlock outputs 3. 200 milli-amp output for 2nd channel trunk release 4. Dual polarity parking light with 2 fuses (one for main power / one parking light power input) on the 5-pin power harness.) 5. On board parking light relay (same as Auto Page standard) Specifications:
Programming:
PROGRAMMING:
Note: This system can keep up to 4 remote transmitters in its memory. If more than 4 transmitters programmed, the system will keep only the last 4 transmitters. PROGRAMMING THE REMOTE TRANSMITTER Enter:
1. Turn the Ignition switch OFF/ON 3 TIMES and stay in ON position. Within 15 seconds. 2. Push the Valet switch 2 times. (Holding in on the 2nd push) until you hear a long chirp. The transmitter is ready to program. Program:
1. Press any button on the transmitter until the siren responds with a confirming chirp the first transmitter is now programmed. 2. Press button on the second transmitter until the siren responds with a confirming chirp, the second transmitter is now programmed. 3. Apply the same procedure to program 3rd and 4th. Exit: Turn Ignition to OFF position, or leave it for 15 seconds. A 3 long chirps & 3 parking light flashes to confirm exit. FEATURE PROGRAMMING:
FEATURE A PROGRAMMING:
1. Turn the Ignition switch ON/OFF 3 TIMES and stay in OFF position. 2. Push the Valet switch 3 times (holding in on the 3rd push) until one chirp with a long chirp is heard, then release the valet switch. You are now in the Alarm feature A programming mode. 3. Press and release the transmitter button corresponding to the feature you want to program.
(See chart on next page) The siren chirps and LED pause will indicate new setting. The factory default settings are always [1] LED flash, [1] siren chirp. 4. Depress the transmitter button to change the feature. Simply keep re-depressing the transmitter button again until the module advances to your desired setting. a. In this case, Press the button again, the module would advance to [2] LED flash, [2] horn chirp. b. Press the button again; the module would advance to [3] LED flash, [3] horn chirps etc. Press Transmitter Button 1 2 3 4 5
One Chirp /
LED one pulse Factory Default Setting Active arming Two Chirps /
LED two pulses Three Chirps /
LED three pulses Passive arming without passive door locking Passive arming with passive door locking. Automatic Rearm off Automatic Rearm on Instant Door Ajar error chirp Siren Confirmation chirp on only Ignition Alarm trigger ON 45 seconds delay Door Ajar error chirp. All Confirmation chirps off Ignition Alarm trigger OFF Four Chirps /
LED four pulses Exit: Turn Ignition to ON position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit. Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. THIS DEVICE COMPLIES WITH PART 15 OF THE FCCRULES. OPERATIONS IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: ( 1 ) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND ( 2 ) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFEERENCE THAT MAY CAUSE UNDESRIED OPERATION FEATURE B PROGRAMMING:
1 Turn the Ignition switch ON/OFF 3 TIMES and stay in OFF position. 2 Push the Valet switch 5 times (holding in on the 5th push) until two chirps with a long chirp is heard then release the valet switch. You are now in the Alarm feature B programming mode. 3 Press and release the transmitter button corresponding to the feature you want to program. Press Transmitter Button 1 One Chirp /
LED one pulse Factory Default Setting Pathway illumination feature off Ignition controlled door locks &
unlocks Two Chirps /
LED two pulses Parking light turns on for 30- second upon an unlock signal Ignition controlled door locks only Three Chirps /
LED three pulses Four Chirps /
LED four pulses Without ignition controlled door locks &
unlocks Ignition controlled door unlocks only Double pulse unlock 0.8-second Door lock pulses. Car Jacking Off H1/4 Brown Wire =
(+) Siren Output 3.5-second Door lock pulse. Car Jacking On H1/4 Brown Wire =
(+) Horn pulse Output (Relay Required for negative out) 2 3 4
5
Exit: Turn Ignition to ON position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit. Transmitter Operation Transmitter Button System Function Remark Lock Doors & Arm System Panic function Car Locator Arm and Delete The 2 Stage Shock Sensor Silent Arming / Disarming Unlock Doors & Disarm System Two Steps Door Unlock & Disarm System Trunk Release (Channel 2) Passive Arming By-pass Silent Arming / Disarming Control another car Press and Hold for 3 seconds Under armed mode Press twice within 3 seconds Ignition in "off" position. Press twice within 3 seconds. Press and Hold for 2 seconds While the system Disarmed. Press within 3 seconds Press and Hold for 2 seconds
II