MONITORED WIRELESS EDGE KIT MONITORED WIRELESS EDGE KIT MONITORED WIRELESS EDGE KIT Model/Modle/Modelo LMWEKITU Review Copy To prevent possible SERIOUS INJURY or DEATH from a closing gate or door:
Be sure to DISCONNECT ALL POWER to the operator BEFORE installing the wireless edge kit. The gate or door MUST be in the fully opened or closed position BEFORE installing the LiftMaster Monitored Entrapment Protection device. Correctly install and connect the wireless edge kit. LiftMaster Monitored Entrapment Protection devices are for use with LiftMaster UL 325 compliant Gate and Commercial Door Operators ONLY. Use with ANY other product voids the warranty. Monitored external entrapment protection devices MUST be installed per the operator installation manual for each Entrapment Zone. To prevent possible SERIOUS INJURY or DEATH from a closing gate or door:
Be sure to DISCONNECT ALL POWER to the operator BEFORE installing the wireless edge kit. The gate or door MUST be in the fully opened or closed position BEFORE installing the LiftMaster Monitored Entrapment Protection device. Correctly install and connect the wireless edge kit. LiftMaster Monitored Entrapment Protection devices are for use with LiftMaster UL 325 compliant Gate and Commercial Door Operators ONLY. Use with ANY other product voids the warranty. Monitored external entrapment protection devices MUST be installed per the operator installation manual for each Entrapment Zone. ADVERTENCIA To prevent possible SERIOUS INJURY or DEATH from a closing gate or door:
Be sure to DISCONNECT ALL POWER to the operator BEFORE installing the wireless edge kit. The gate or door MUST be in the fully opened or closed position BEFORE installing the LiftMaster Monitored Entrapment Protection device. Correctly install and connect the wireless edge kit. LiftMaster Monitored Entrapment Protection devices are for use with LiftMaster UL 325 compliant Gate and Commercial Door Operators ONLY. Use with ANY other product voids the warranty. Monitored external entrapment protection devices MUST be installed per the operator installation manual for each Entrapment Zone. ATTENTION AVERTISSEMENT AVERTISSEMENT AVERTISSEMENT 2 Review Copy CARTON INVENTORY INVENTAIRE DE LEMBALLAGE CONTENIDO DE LA CAJA AA Lithium Batteries (2) Energizer Ultimate Lithium AA L91 recommended as replacements AA Lithium Batteries (2) Energizer Ultimate Lithium AA L91 recommended as replacements AA Lithium Batteries (2) Energizer Ultimate Lithium AA L91 recommended as replacements I2C Dongle I2C Dongle I2C Dongle 1" Screw (8) 1" Screw (8) 1" Screw (8)
.375" Screw (8)
.375" Screw (8)
.375" Screw (8) Mounting Bracket (2) Mounting Bracket (2) Mounting Bracket (2) Transmitter Transmitter Transmitter Receiver Receiver Receiver INTRODUCTION The LiftMaster Wireless Edge Kit provides a Bluetooth connection between a LiftMaster monitored resistive edge (not included) and the gate operator. Maximum range is 130 ft. (objects in the path of the signal and location of devices may reduce range). You can program up to 4 transmitters to the receiver. The kit works with LiftMaster monitored resistive edge sensors ONLY. Contact closure edge sensors are NOT supported. For use with LiftMaster gate operators that meet UL 325 requirements. Transmitter and receiver are UL Recognized Components and meet UL 325 requirements. A monitored safety device MUST be installed in each entrapment zone. INTRODUCTION The LiftMaster Wireless Edge Kit provides a Bluetooth connection between a LiftMaster monitored resistive edge (not included) and the gate operator. Maximum range is 130 ft. (objects in the path of the signal and location of devices may reduce range). You can program up to 4 transmitters to the receiver. The kit works with LiftMaster monitored resistive edge sensors ONLY. Contact closure edge sensors are NOT supported. For use with LiftMaster gate operators that meet UL 325 requirements. Transmitter and receiver are UL Recognized Components and meet UL 325 requirements. A monitored safety device MUST be installed in each entrapment zone. INTRODUCCIN The LiftMaster Wireless Edge Kit provides a Bluetooth connection between a LiftMaster monitored resistive edge (not included) and the gate operator. Maximum range is 130 ft. (objects in the path of the signal and location of devices may reduce range). You can program up to 4 transmitters to the receiver. The kit works with LiftMaster monitored resistive edge sensors ONLY. Contact closure edge sensors are NOT supported. For use with LiftMaster gate operators that meet UL 325 requirements. Transmitter and receiver are UL Recognized Components and meet UL 325 requirements. A monitored safety device MUST be installed in each entrapment zone. 3 Review Copy 1 WIRE RECEIVER 1. Find the operator diagram on pages 12-18 to see the mounting location for the receiver and wire routing. 2. Open the receiver housing. 3. Route the wire harness from the receiver to the operator control board. Connect the wire harness to the EXP. BOARD terminal on the control board or to the expansion board (if installed) using the provided I2C dongle. Connect the dongle to the TO MAIN BOARD terminal on the expansion board. The blue power LED will come on. WIRE RECEIVER 1. Find the operator diagram on pages 12-18 to see the mounting location for the receiver and wire routing. 2. Open the receiver housing. 3. Route the wire harness from the receiver to the operator control board. Connect the wire harness to the EXP. BOARD terminal on the control board or to the expansion board (if installed) using the provided I2C dongle. Connect the dongle to the TO MAIN BOARD terminal on the expansion board. The blue power LED will come on. WIRE RECEIVER 1. Find the operator diagram on pages 12-18 to see the mounting location for the receiver and wire routing. 2. Open the receiver housing. 3. Route the wire harness from the receiver to the operator control board. Connect the wire harness to the EXP. BOARD terminal on the control board or to the expansion board (if installed) using the provided I2C dongle. Connect the dongle to the TO MAIN BOARD terminal on the expansion board. The blue power LED will come on. 2 3 OR OU O Control Board Tableau de commande Tarjeta de control To Main Control Board To Main Control Board To Main Control Board I2C Dongle I2C Dongle I2C Dongle Expansion Board Tableau dextension Tarjeta de expansin Illustrations in manual are for reference only, your application may look different Les illustrations dans le manuel sont fournies titre de rfrence uniquement; votre application peut avoir une autre apparence. Las ilustraciones del manual se ofrecen nicamente como referencia, su instalacin podra ser diferente. 4 Review Copy 2 INSTALL TRANSMITTER BATTERIES AND SET EDGE DIRECTION 1. Open the transmitter housing. 2. Install the batteries. 3. Decide the direction (open or closed) the edge will be installed. Set OPEN/CLOSE DIP switch to match the direction of the edge protection. INSTALL TRANSMITTER BATTERIES AND SET EDGE DIRECTION 1. Open the transmitter housing. 2. Install the batteries. 3. Decide the direction (open or closed) the edge will be installed. Set OPEN/CLOSE DIP switch to match the direction of the edge protection. INSTALL TRANSMITTER BATTERIES AND SET EDGE DIRECTION 1. Open the transmitter housing. 2. Install the batteries. 3. Decide the direction (open or closed) the edge will be installed. Set OPEN/CLOSE DIP switch to match the direction of the edge protection. OPEN/CLOSE Dip Switches OPEN/CLOSE Dip Switches OPEN/CLOSE Dip Switches 3 PROGRAMMING The receiver can learn up to 4 transmitters. 1. Press the learn button on the RECEIVER board. The red LED will come on and the operator control board will beep once to indicate programming mode. NOTE: Press the learn button again to exit programming mode. 2. Press the learn button on the TRANSMITTER to be learned. The red LED on the RECEIVER will blink 4 times. Press the learn button on the next TRANSMITTER to be learned. NOTE: Learn mode times out after 60 seconds if no transmitters are added or the capacity is reached. After each transmitter is learned there will be an additional 60 seconds to complete programming. PROGRAMMATION The receiver can learn up to 4 transmitters. 1. Press the learn button on the RECEIVER board. The red LED will come on and the operator control board will beep once to indicate programming mode. NOTE: Press the learn button again to exit programming mode. 2. Press the learn button on the TRANSMITTER to be learned. The red LED on the RECEIVER will blink 4 times. Press the learn button on the next TRANSMITTER to be learned. NOTE: Learn mode times out after 60 seconds if no transmitters are added or the capacity is reached. After each transmitter is learned there will be an additional 60 seconds to complete programming. PROGRAMACIN The receiver can learn up to 4 transmitters. 1. Press the learn button on the RECEIVER board. The red LED will come on and the operator control board will beep once to indicate programming mode. NOTE: Press the learn button again to exit programming mode. 2. Press the learn button on the TRANSMITTER to be learned. The red LED on the RECEIVER will blink 4 times. Press the learn button on the next TRANSMITTER to be learned. NOTE: Learn mode times out after 60 seconds if no transmitters are added or the capacity is reached. After each transmitter is learned there will be an additional 60 seconds to complete programming. Learn Button Bouton Apprendre Botn de Programacin 5 Review Copy 4 MOUNT THE RECEIVER 1. Find the operator diagram on pages 12-18 to see the mounting location for the receiver. 2. Attach the mounting bracket to the gate operator. 3. Reattach the receiver housing. 4. Snap the receiver onto the mounting bracket and secure with screw provided. MOUNT THE RECEIVER 1. Find the operator diagram on pages 12-18 to see the mounting location for the receiver. 2. Attach the mounting bracket to the gate operator. 3. Reattach the receiver housing. 4. Snap the receiver onto the mounting bracket and secure with screw provided. MOUNT THE RECEIVER 1. Find the operator diagram on pages 12-18 to see the mounting location for the receiver. 2. Attach the mounting bracket to the gate operator. 3. Reattach the receiver housing. 4. Snap the receiver onto the mounting bracket and secure with screw provided. 2 3 4 6 Review Copy 5 1 3 WIRE AND MOUNT THE TRANSMITTER(S) NOTE: The transmitter can be wired to 1 or 2 edge sensors. 1. Route the wires from the edge sensor into the transmitter. Connect the wires to the terminal blocks (polarity is NOT 2. Attach the mounting bracket to the gate using the screws provided. If installing on a round surface, use zip ties (not 3. Reattach the transmitter housing. 4. Snap the transmitters onto the mounting bracket and secure with the screw provided. WIRE AND MOUNT THE TRANSMITTER(S) NOTE: The transmitter can be wired to 1 or 2 edge sensors. 1. Route the wires from the edge sensor into the transmitter. Connect the wires to the terminal blocks (polarity is NOT 2. Attach the mounting bracket to the gate using the screws provided. If installing on a round surface, use zip ties (not 3. Reattach the transmitter housing. 4. Snap the transmitters onto the mounting bracket and secure with the screw provided. WIRE AND MOUNT THE TRANSMITTER(S) NOTE: The transmitter can be wired to 1 or 2 edge sensors. 1. Route the wires from the edge sensor into the transmitter. Connect the wires to the terminal blocks (polarity is NOT 2. Attach the mounting bracket to the gate using the screws provided. If installing on a round surface, use zip ties (not important). provided). important). provided). important). provided). 3. Reattach the transmitter housing. 4. Snap the transmitters onto the mounting bracket and secure with the screw provided. 2 4 7 Review Copy 6 TEST Apply pressure to edge. The red LED on the TRANSMITTER and the corresponding open or close edge LED on the gate operator control board will flash. If the TRANSMITTER LED does not flash, check the transmitter and edge sensor for proper installation and wiring. TEST Apply pressure to edge. The red LED on the TRANSMITTER and the corresponding open or close edge LED on the gate operator control board will flash. If the TRANSMITTER LED does not flash, check the transmitter and edge sensor for proper installation and wiring. TEST Apply pressure to edge. The red LED on the TRANSMITTER and the corresponding open or close edge LED on the gate operator control board will flash. If the TRANSMITTER LED does not flash, check the transmitter and edge sensor for proper installation and wiring. Status LED Status LED Status LED 8 Review Copy BATTERY STATUS During normal operation, the red status LEDs on the transmitter(s) and receiver flash to indicate the battery status. NOTE: The receiver LED corresponds to the lowest battery level of all transmitters. 1 Flash 2 Flashes 3 Flashes Battery is fine. Battery is low; the operator will beep twice. Battery is critically low; the operator will not function until the battery is replaced. The operator will either open automatically (fail-safe) or latch at close (fail-secure) based on the operator setting (see the gate operator manual for more information). BATTERY STATUS During normal operation, the red status LEDs on the transmitter(s) and receiver flash to indicate the battery status. NOTE: The receiver LED corresponds to the lowest battery level of all transmitters. 1 Flash 2 Flashes 3 Flashes Battery is fine. Battery is low; the operator will beep twice. Battery is critically low; the operator will not function until the battery is replaced. The operator will either open automatically (fail-safe) or latch at close (fail-secure) based on the operator setting (see the gate operator manual for more information). BATTERY STATUS During normal operation, the red status LEDs on the transmitter(s) and receiver flash to indicate the battery status. NOTE: The receiver LED corresponds to the lowest battery level of all transmitters. 1 Flash 2 Flashes 3 Flashes Battery is fine. Battery is low; the operator will beep twice. Battery is critically low; the operator will not function until the battery is replaced. The operator will either open automatically (fail-safe) or latch at close (fail-secure) based on the operator setting (see the gate operator manual for more information). Transmitter Transmitter Transmitter Status LED Status LED Status LED Status LED Status LED Status LED Receiver Receiver Receiver 9 Review Copy REMOVE A TRANSMITTER 1. Disconnect the edge sensor wires from the TRANSMITTER. 2. Remove the batteries from the TRANSMITTER. 3. Press and hold the RECEIVER learn button until the red status LED begins to flash (about 3 seconds) then release. The receiver will remove disconnected transmitters from memory and return to normal operation after 60 seconds or when the user presses the learn button again. REMOVE A TRANSMITTER 1. Disconnect the edge sensor wires from the TRANSMITTER. 2. Remove the batteries from the TRANSMITTER. 3. Press and hold the RECEIVER learn button until the red status LED begins to flash (about 3 seconds) then release. The receiver will remove disconnected transmitters from memory and return to normal operation after 60 seconds or when the user presses the learn button again. REMOVE A TRANSMITTER 1. Disconnect the edge sensor wires from the TRANSMITTER. 2. Remove the batteries from the TRANSMITTER. 3. Press and hold the RECEIVER learn button until the red status LED begins to flash (about 3 seconds) then release. The receiver will remove disconnected transmitters from memory and return to normal operation after 60 seconds or when the user presses the learn button again. 1-2 3 Transmitter Transmitter Transmitter Learn Button Bouton Apprendre Botn de Programacin Receiver Receiver Receiver ERASE ALL TRANSMITTERS FROM MEMORY Press and hold the RECEIVER learn button until the red status LED begins to flash. Hold the learn button until the LED turns off (about 10 seconds) then release. The gate operator will beep for 5 seconds to confirm all transmitters are erased. ERASE ALL TRANSMITTERS FROM MEMORY Press and hold the RECEIVER learn button until the red status LED begins to flash then turns off (about 10 seconds) then release. The operator will beep for 5 seconds to confirm all transmitters are erased. ERASE ALL TRANSMITTERS FROM MEMORY Press and hold the RECEIVER learn button until the red status LED begins to flash then turns off (about 10 seconds) then release. The operator will beep for 5 seconds to confirm all transmitters are erased. 10 Review Copy TROUBLESHOOTING The diagnostic display on the operator control board will display an error code to indicate a problem. See the gate operator manual for instructions to display error codes. 46 Wireless edge battery low 67 Wireless edge triggered more than 3 minutes 68 Wireless edge loss of monitoring 69 Wireless edge triggered Replace batteries in wireless edge. Check wired input for wiring issue or obstruction. Check wireless edge inputs. Check for connection between receiver and main board/expansion board. IF an obstruction occurred, no action required. If an obstruction did NOT occur, check inputs and wiring. DPANNAGE The diagnostic display on the operator control board will display an error code to indicate a problem. See the gate operator manual for instructions to display error codes. Pile faible du chant sans fil Chant sans fil dclench pendant plus de 3 minutes Perte de surveillance du chant sans fil Remplacer les piles du chant sans fil. Vrifi er lentre cble pour tout problme de cblage ouobstruction. Vrifi er les entres du chant sans fil. Check for connection between receiver and main board/expansion board. Si une obstruction sest produite, aucune action nest requise. Si une obstruction ne sest pas produite, vrifi er les entres et le cblage. 69 Chant sans fil dclench 46 67 68 RESOLUCIN DE PROBLEMAS The diagnostic display on the operator control board will display an error code to indicate a problem. See the gate operator manual for instructions to display error codes. 46 Wireless edge battery low 67 Wireless edge triggered more than 3 minutes 68 Wireless edge loss of monitoring Replace batteries in wireless edge. Check wired input for wiring issue or obstruction. Check wireless edge inputs. Check for connection between receiver and main board/expansion board. IF an obstruction occurred, no action required. If an obstruction did NOT occur, check inputs and wiring. 69 Wireless edge triggered Control Board Tableau de commande Tarjeta de control DIAGNOSTICS 11 Review Copy MODEL RSW12U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. MODEL RSW12U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. MODEL RSW12U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. RSW12U A 7-1/2" (19.05 cm) B 4-7/16" (11.27 cm) C 6-1/8" (15.55 cm) A 7-1/2" (19.05 cm) B 4-7/16" (11.27 cm) C 6-1/8" (15.55 cm) RSW12U B C A B C A 12 Review Copy MODEL CSW24U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. MODLE CSW24U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. MODELO CSW24U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. CSW24U A 7-1/2" (19.05 cm) B 4-7/16" (11.27 cm) C 6-1/8" (15.55 cm) A 7-1/2" (19.05 cm) B 4-7/16" (11.27 cm) C 6-1/8" (15.55 cm) CSW24U C A B B 13 C A Review Copy MODELS RSL12U AND CSL24U - RECEIVER MOUNTING LOCATION MODLES RSL12U ET CSL24U - RECEIVER MOUNTING LOCATION MODELOS RSL12U Y CSL24U - RECEIVER MOUNTING LOCATION A 5" (12.7 cm) B 4-7/16" (11.27 cm) C 1-3/4" (4.44 cm) CSL24U B A C C B A 14 RSL12U A 1-1/2" (3.81 cm) B 4-7/16" (11.27 cm) C 3-3/16" (8.09 cm) Review Copy MODELS LA400, LA412, AND LA500 - RECEIVER MOUNTING LOCATION MODLES LA400U, LA412, ET LA500 - RECEIVER MOUNTING LOCATION MODELOS LA400U, LA412, Y LA500 - RECEIVER MOUNTING LOCATION A 5-1/8" (13.01 cm)) B 4-7/16" (11.27 cm) C 1" (2.54 cm) C B A STANDARD CONTROL BOX GRAND BOTER DE CONTRLE EN MTAL CAJA DE CONTROL METLICA GRANDE STANDARD CONTROL BOX BOTER DE CONTRLE STANDARD CAJA DE CONTROL ESTNDAR A 1" (2.54 cm) B 4-7/16" (11.27 cm) C 3-1/2" (8.89 cm) C A B 15 Review Copy MODEL CSW200U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. MODLE CSW200U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. MODELO CSW200U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. CSW200U A 9" (22.86 cm) B 4-7/16" (11.27 cm) C 1-1/2" (3.81 cm) A 8" (20.32 cm) B 4-7/16" (11.27 cm) C 3-3/4" (9.52 cm) CSW200U C B A B C A 16 Review Copy MODEL SL3000U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. MODLE SL3000U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. MODELO SL3000U - RECEIVER MOUNTING LOCATION Mount the bracket on the side facing the gate. A 3-1/4" (8.25 cm) B 4-7/16" (11.27 cm) C 1" (2.54 cm) SL3000 C B A 17 Review Copy MODELS SL585 AND SL595 - RECEIVER MOUNTING LOCATION MODLES SL585 AND SL595 - RECEIVER MOUNTING LOCATION MODELOS SL585 AND SL595 - RECEIVER MOUNTING LOCATION A 4-1/16" (10.3 cm) B 4-7/16" (11.27 cm) C 1" (2.54 cm) C B A SL585 A 6" (15.24 cm) C 11-3/4" (29.84 cm) B 4-7/16" (11.27 cm) D 1" (2.54 cm) C B D A SL595
.875" (2.22 cm) 18 Review Copy WARRANTY LiftMaster warrants to the first consumer purchaser of this product that it is free from defect in materials and/or workmanship for a period of 2 years from the date of purchase. GARANTIE LiftMaster garantit lacheteur initial de ce produit que celui-ci est exempt de tout dfaut matriel ou de fabrication pendant une priode de deux ans suivant la date dachat. GARANTA LiftMaster garantiza al primer comprador minorista de este producto, que el mismo est libre de defectos de materiales y de mano de obra por un perodo de dos aos a partir de la fecha de compra. NOTICE: This device complies with part 15 of the FCC rules and Industry Canada (IC) licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This Class B digital apparatus complies with Canadian ICES-003. This device must be installed in a way where a minimum 8" (20cm) distance is maintained between users/bystanders and device. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. AVIS : Ce dispositif est conforme la partie 15 des rgles de la FCC et des normes RSS exemptes de licence dIndustrie Canada (IC). Lutilisation est assujettie aux deux conditions ci-aprs : (1) ce dispositif ne doit pas causer dinterfrences nuisibles, et (2) ce dispositif doit accepter toute interfrence reue, y compris une interfrence pouvant causer un fonctionnement indsirable. Tout changement ou toute modification non expressment approuvs par la partie responsable de la conformit pourrait annuler lautorit de lutilisateur dutiliser lquipement. Cet appareil numrique de classe B est conforme la norme ICES-003 du Canada. This device must be installed in a way where a minimum 8 (20cm) distance is maintained between users/bystanders and device. Ce dispositif a t mis lessai et dclar conforme aux limites tablies pour les dispositifs numriques de classe B, conformment larticle 15 des rgles de la FCC. Cette conformit a pour but de fournir une protection raisonnable contre les interfrences nuisibles dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre des frquences radio et, sil nest pas install et utilis conformment aux instructions, causer des interfrences nuisibles aux communications radio. Cependant, il nexiste aucune garantie que des interfrences ne se produiront pas dans une installation particulire. Si cet quipement provoque des interfrences nuisibles la rception dune diffusion sonore ou visuelle, ce qui peut tre dtermin en lallumant et en lteignant, lutilisateur est invit essayer de rsoudre ce problme en prenant une ou plusieurs des mesures suivantes :
- Rorienter ou dplacer antenne de rception.
- Augmenter la distance entre lquipement et le rcepteur.
- Brancher lappareil une prise sur un circuit diffrent de celui du rcepteur.
- Pour obtenir de laide, consulter le dtaillant ou un radiotechnicien expriment. AVISO: Este dispositivo cumple con la Parte 15 de las normas FCC y las normas RSS con excepcin de licencia de Industry Canada (IC) de Canad. El uso est sujeto a las siguientes condiciones: (1) Este dispositivo no debe causar interferencia perjudicial, y (2) este dispositivo debe poder recibir interferencia, incluso interferencia que pueda afectar su funcionamiento. Todo cambio o toda modificacin no expresamente aprobada por la parte responsable del cumplimiento podra anular el derecho de usar el equipo. Este aparato digital de Clase B cumple con las normas canadienses ICES-003 This device must be installed in a way where a minimum 8 (20cm) distance is maintained between users/bystanders and device. Este dispositivo ha sido probado y cumple con los lmites establecidos para un dispositivo digital de Clase B segn la Parte 15 de las Normas de FCC de EE.UU. Estos lmites tienen por objeto brindar un grado razonable de proteccin contra interferencias molestas en una instalacin residencial. Este equipo genera, usa y puede emitir energa de radiofrecuencia. Si no se instala y utiliza de acuerdo con las instrucciones podr causar interferencia con comunicaciones radiales. Aun as, no hay garanta de que no se produzcan interferencias en una instalacin particular. Si este equipo produce interferencia en la recepcin de radio o televisin, lo cual puede determinarse apagando y encendiendo la unidad, el usuario debe tratar de corregir el problema por medio de lo siguiente:
- Reorientar o reubicar la antena de recepcin.
- Aumentar la distancia de separacin entre el equipo y el receptor.
- Conectar el equipo a un tomacorriente de un circuito elctrico diferente al que est conectado el receptor.
- Consultar al distribuidor del producto o a un tcnico idneo de radio y televisin. 19 Review Copy For parts and accessories visit LiftMaster.com Pour les pices et accessoires, allez LiftMaster.com En LiftMaster.com pueden adquirirse repuestos y accesorios LiftMaster 845 Larch Avenue Elmhurst, IL 60126-1196 LiftMaster.com The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. ALPHA 2015, LiftMaster All Rights Reserved Tous droits rservs Todos los derechos reservados Review Copy