Children operating or playing with a garage door opener can injure themselves or others. The garage door could close We oDeCU rity+ and cause serious injury or death. Do not allow children to 3-Chann el Mini Remote Control operate the wall push buttons or remote controls.
' A moving garage door could injure or kill someone under OWNER'S MANUAL it. Activate the opener only when you can see the door The 90 Series remote control (Security+) works only with clearly, it is free of obstructions, and (s properly adjusted. door openers and light controls having an orange Smart :
NOTICE: This device complies with Part 15 of the FCC Rules: Operation is subject to the button anda yellow indicator light. following two conditions: (1) this device may not case harmful interference, and (2) this. device
. ; 7 must acept any interference received, including interference that may cause undesired operation. Programming instructions are described and illustrated To comply with FCC/IC rules, adjustment or modification of this receiver and/or transmitter is iti i prohibited, except for changing the code setting or replacing the battery. THERE ARE NO below. The additional push buttons can also activate other prohibited, except for changing wee garage door openers and/or light controls. (Instructions for programming light products are included with those accessories.) To Control the Opener Lights
(only if you have a Multifunction door control) With Security* transmitters, a remote push button can be Security+ Garage Door Openers programmed to operate the opener lights without opening the To Program the Opener to Accept door. |
the Remote Control Code 1. With the door closed, press and hold the remote button that you want to control the light. Select a remote control push button to operate the opener. The 2. Press and hold the Light button on the door control.
/arge button is recommended for use with a garage door opener. 1. Press and fold the selected remote control push button. See 3. Press and hold the Lock button on the door control. Figure 1. 4. After the opener lights flash, release all buttons. 2. Press and release the Smart button on the opener panel. Test by pressing the remote push button. The opener lights See Figure 2. The indicator light on the panel will begin to should turn on or off but the door should not move. blink and the opener lights will fash once. Open/Close/Stop Operation 3. Release the remote push button. (only if you have a Multifunction door control) Now the opener will operate when that remote control button is Your Security# remote control can be programmed to operate pressed. Test it by pressing the remote button to see that the one door using all 3 buttons: the /e/f button will only open the door goes up and down. door, the m/dd/e button will only close the door, and the third Model Sect, 970 ~316 LG SECURITY+# Dutton wil riop ime doors movement. You may set up this Security+ Garage Door Opener Open Close 1. With the door closed, press and hold the feftremote push button. 2. Press and hold the Lock button on the door control. 3. Press and hold the door control push bar. ay be ee ca id push button "Smart" ;
Figure 1 Figure 2 Butt-n Indicator Light When the opener lights flash, release all buttons. Test by pressing the left (Open) button on the remote. The door should Adding a remote can also be done from a Multifunction door open. Press it again while the door is open and nothing should control, as follows: happen. Press the middle (C/ose) button and the door should 1. With the door closed, press and hold a remote push button. close. Press the third (Sfop) button while the door is moving 2. Press and hold the Light button on the door control. and it should stop immediately. 3. Press and hold the door control push bar. 4. After the opener lights flash, release all buttons. Test by pressing the remote push button. To Erase All Remote Control Codes Press and hold the Smart button on the opener pane! until the indicator light turns off (about 6 seconds). All transmitter codes are now erased. Then follow the steps above to re-program each remote control. The lithium battery should produce power for up to 5 years. To replace battery, pry open The Remote Control Battery G70 -3'54G Replacement Parts Model 976tNrSecurity# remote case ........... eedues 2 case as shown. Insert battery
(circuit board not included) positive side up. Dispose of old 3V2032 Lithium battery ...... 0... cece cece eee eeveeeeees battery properly. FOR SERVICE DIAL OUR TOLL FREE NUMBER: 1-800-528-2817 2000, Fhe Chamberlain Group, Inc. tteastosn 1/4A25 68 All Rights Reserved Printed in Mexico